pve-docs/pvesdn.adoc

[[chapter_pvesdn]]
Software Defined Network
========================
ifndef::manvolnum[]
:pve-toplevel:
endif::manvolnum[]

The **S**oftware **D**efined **N**etwork (SDN) feature allows one to create
virtual networks (vnets) at datacenter level.

WARNING: SDN is currently an **experimental feature** in {pve}. This
Documentation for it is also still under development, ask on our
xref:getting_help[mailing lists or in the forum] for questions and feedback.


[[pvesdn_installation]]
Installation
------------

To enable the experimental SDN integration, you need to install
"libpve-network-perl" package

----
apt install libpve-network-perl
----

You need to have `ifupdown2` package installed on each node to manage local
configuration reloading without reboot:

----
apt install ifupdown2
----

Basic Overview
--------------

The {pve} SDN allows separation and fine grained control of Virtual Guests
networks, using flexible software controlled configurations.

Separation consists of zones, a zone is it's own virtual separated network area.
A 'VNet' is a type of a virtual network connected to a zone. Depending on which
type or plugin the zone uses it can behave differently and offer different
features, advantages or disadvantages.
Normally a 'VNet' shows up as a common Linux bridge with either a VLAN or
'VXLAN' tag, but some can also use layer 3 routing for control.
The 'VNets' are deployed locally on each node, after configuration was committed
from the cluster wide datacenter SDN administration interface.


Main configuration
------------------

The configuration is done at datacenter (cluster-wide) level, it will be saved
in configuration files located in the shared configuration file system:
`/etc/pve/sdn`

On the web-interface  SDN feature have 4 main sections for the configuration

* SDN: a overview of the SDN state

* Zones: Create and manage the virtual separated network Zones

* VNets: The per-node building block to provide a Zone for VMs

* Controller: For complex setups to control Layer 3 routing


[[pvesdn_config_main_sdn]]
SDN
~~~

This is the main status panel. Here you can see deployment status of zones on
different nodes.

There is an 'Apply' button, to push and reload local configuration on all
cluster nodes nodes.


[[pvesdn_config_zone]]
Zones
~~~~~

A zone will define a virtually separated network.

It can use different technologies for separation:

* VLAN: Virtual LANs are the classic method to sub-divide a LAN

* QinQ: stacked VLAN (formally known as `IEEE 802.1ad`)

* VXLAN: (layer2 vxlan)

* bgp-evpn: vxlan using layer3 border gateway protocol routing

You can restrict a zone to specific nodes.

It's also possible to add permissions on a zone, to restrict user to use only a
specific zone and only the VNets in that zone

[[pvesdn_config_vnet]]
VNets
~~~~~

A `VNet` is in its basic form just a Linux bridge that will be deployed locally
on the node and used for Virtual Machine communication.

VNet properties are:

* ID: a 8 characters ID to name and identify a VNet

* Alias: Optional longer name, if the ID isn't enough

* Zone: The associated zone for this VNet

* Tag: The unique VLAN or VXLAN id

* VLAN Aware: Allow to add an extra VLAN tag in the virtual machine or
  container vNIC configurations or allow the guest OS to manage the VLAN's tag.

* IPv4: an anycast IPv4 address, it will be configured on the underlying bridge
  on each node part of the Zone. It's only useful for `bgp-evpn` routing.

* IPv6: an anycast IPv6 address, it will be configured on the underlying bridge
  on each node part of the Zone. It's only useful for `bgp-evpn` routing.


[[pvesdn_config_controllers]]
Controllers
~~~~~~~~~~~

Some zone types need an external controller to manage the VNet control-plane.
Currently this is only required for the `bgp-evpn` zone plugin.


[[pvesdn_zone_plugins]]
Zones Plugins
-------------

Common options
~~~~~~~~~~~~~~

nodes:: Deploy and allow to use a VNets configured for this Zone only on these
nodes.

[[pvesdn_zone_plugin_vlan]]
VLAN Zones
~~~~~~~~~~

This is the simplest plugin, it will reuse an existing local Linux or OVS
bridge, and manage VLANs on it.
The benefit of using SDN module, is that you can create different zones with
specific VNets VLAN tag, and restrict Virtual Machines to separated zones.

Specific `VLAN` configuration options:

bridge:: Reuse this local bridge or OVS switch, already
configured on *each* local node.

[[pvesdn_zone_plugin_qinq]]
QinQ Zones
~~~~~~~~~~

QinQ is stacked VLAN. The first VLAN tag defined for the zone
(so called 'service-vlan'), and the second VLAN tag defined for the vnets

NOTE: Your physical network switches must support stacked VLANs!

Specific QinQ configuration options:

bridge:: A local VLAN-aware bridge already configured on each local node

service vlan:: The main VLAN tag of this zone

mtu:: Due to the double stacking of tags you need 4 more bytes for QinQ VLANs.
For example, you reduce the MTU to `1496` if you physical interface MTU is
`1500`.

[[pvesdn_zone_plugin_vxlan]]
VXLAN Zones
~~~~~~~~~~~

The VXLAN plugin will establish a tunnel (named overlay) on top of an existing
network (named underlay). It encapsulate layer 2 Ethernet frames within layer
4 UDP datagrams, using `4789` as the default destination port. You can, for
example, create a private IPv4 VXLAN network on top of public internet network
nodes.
This is a layer2 tunnel only, no routing between different VNets is possible.

Each VNet will have use specific VXLAN id from the range (1 - 16777215).

Specific EVPN configuration options:

peers address list:: A list of IPs from all nodes through which you want to
communicate. Can also be external nodes.

mtu:: Because VXLAN encapsulation use 50bytes, the MTU need to be 50 bytes
lower than the outgoing physical interface.

[[pvesdn_zone_plugin_evpn]]
EVPN Zones
~~~~~~~~~~

This is the most complex of all supported plugins.

BGP-EVPN allows one to create routable layer3 network. The VNet of EVPN can
have an anycast IP-address and or MAC-address. The bridge IP is the same on each
node, with this a virtual guest can use that address as gateway.

Routing can work across VNets from different zones through a VRF (Virtual
Routing and Forwarding) interface.

Specific EVPN configuration options:

VRF VXLAN Tag:: This is a vxlan-id used for routing interconnect between vnets,
it must be different than VXLAN-id of VNets

controller:: an EVPN-controller need to be defined first (see controller
plugins section)

mtu:: because VXLAN encapsulation use 50bytes, the MTU need to be 50 bytes
lower than the outgoing physical interface.


[[pvesdn_controller_plugins]]
Controllers Plugins
-------------------

For complex zones requiring a control plane.

[[pvesdn_controller_plugin_evpn]]
EVPN Controller
~~~~~~~~~~~~~~~

For `BGP-EVPN`, we need a controller to manage the control plane.
The currently supported software controller is the "frr" router.
You may need to install it on each node where you want to deploy EVPN zones.

----
apt install frr
----

Configuration options:

asn:: A unique BGP ASN number. It's highly recommended to use private ASN
number (64512 – 65534, 4200000000 – 4294967294), as else you could end up
breaking, or get broken, by global routing by mistake.

peers:: An ip list of all nodes where you want to communicate (could be also
external nodes or route reflectors servers)

Additionally, if you want to route traffic from a SDN BGP-EVPN network to
external world:

gateway-nodes:: The proxmox nodes from where the bgp-evpn traffic will exit to
external through the nodes default gateway

gateway-external-peers::  If you want that gateway nodes don't use the default
gateway, but, for example, sent traffic to external BGP routers, which handle
(reverse) routing then dynamically you can use. For example
`192.168.0.253,192.168.0.254'


[[pvesdn_local_deployment_monitoring]]
Local Deployment Monitoring
---------------------------

After applying the configuration through the main SDN web-interface panel,
the local network configuration is generated locally on each node in
`/etc/network/interfaces.d/sdn`, and with ifupdown2 reloaded.

You need to add
----
source /etc/network/interfaces.d/*
----
at the end of /etc/network/interfaces to have the sdn config included

You can monitor the status of local zones and vnets through the main tree.


[[pvesdn_setup_example_vlan]]
VLAN Setup Example
------------------

TIP: While we show plain configuration content here, almost everything should
be configurable using the web-interface only.

Node1: /etc/network/interfaces

----
auto vmbr0
iface vmbr0 inet manual
	bridge-ports eno1
	bridge-stp off
	bridge-fd 0
	bridge-vlan-aware yes
	bridge-vids 2-4094

#management ip on vlan100
auto vmbr0.100
iface vmbr0.100 inet static
	address 192.168.0.1/24

source /etc/network/interfaces.d/*
----

Node2: /etc/network/interfaces

----
auto vmbr0
iface vmbr0 inet manual
	bridge-ports eno1
	bridge-stp off
	bridge-fd 0
	bridge-vlan-aware yes
	bridge-vids 2-4094

#management ip on vlan100
auto vmbr0.100
iface vmbr0.100 inet static
	address 192.168.0.2/24

source /etc/network/interfaces.d/*
----

Create a VLAN zone named `myvlanzone':

----
id: myvlanzone
bridge: vmbr0
----

Create a VNet named `myvnet1' with `vlan-id` `10' and the previously created
`myvlanzone' as it's zone.

----
id: myvnet1
zone: myvlanzone
tag: 10
----

Apply the configuration through the main SDN panel, to create VNets locally on
each nodes.

Create a Debian-based Virtual Machine (vm1) on node1, with a vNIC on `myvnet1'.

Use the following network configuration for this VM:

----
auto eth0
iface eth0 inet static
	address 10.0.3.100/24
----

Create a second Virtual Machine (vm2) on node2, with a vNIC on the same VNet
`myvnet1' as vm1.

Use the following network configuration for this VM:

----
auto eth0
iface eth0 inet static
	address 10.0.3.101/24
----

Then, you should be able to ping between both VMs over that network.


[[pvesdn_setup_example_qinq]]
QinQ Setup Example
------------------

TIP: While we show plain configuration content here, almost everything should
be configurable using the web-interface only.

Node1: /etc/network/interfaces

----
auto vmbr0
iface vmbr0 inet manual
	bridge-ports eno1
	bridge-stp off
	bridge-fd 0
	bridge-vlan-aware yes
	bridge-vids 2-4094

#management ip on vlan100
auto vmbr0.100
iface vmbr0.100 inet static
	address 192.168.0.1/24

source /etc/network/interfaces.d/*
----

Node2: /etc/network/interfaces

----
auto vmbr0
iface vmbr0 inet manual
	bridge-ports eno1
	bridge-stp off
	bridge-fd 0
	bridge-vlan-aware yes
	bridge-vids 2-4094

#management ip on vlan100
auto vmbr0.100
iface vmbr0.100 inet static
	address 192.168.0.2/24

source /etc/network/interfaces.d/*
----

Create an QinQ zone named `qinqzone1' with service VLAN 20

----
id: qinqzone1
bridge: vmbr0
service vlan: 20
----

Create another QinQ zone named `qinqzone2' with service VLAN 30

----
id: qinqzone2
bridge: vmbr0
service vlan: 30
----

Create a VNet named `myvnet1' with customer vlan-id 100 on the previously
created `qinqzone1' zone.

----
id: myvnet1
zone: qinqzone1
tag: 100
----

Create a `myvnet2' with customer VLAN-id 100 on the previously created
`qinqzone2' zone.

----
id: myvnet2
zone: qinqzone2
tag: 100
----

Apply the configuration on the main SDN web-interface panel to create VNets
locally on each nodes.

Create a Debian-based Virtual Machine (vm1) on node1, with a vNIC on `myvnet1'.

Use the following network configuration for this VM:

----
auto eth0
iface eth0 inet static
        address 10.0.3.100/24
----

Create a second Virtual Machine (vm2) on node2, with a vNIC on the same VNet
`myvnet1' as vm1.

Use the following network configuration for this VM:

----
auto eth0
iface eth0 inet static
        address 10.0.3.101/24
----

Create a third Virtual Machine (vm3) on node1, with a vNIC on the other VNet
`myvnet2'.

Use the following network configuration for this VM:

----
auto eth0
iface eth0 inet static
        address 10.0.3.102/24
----

Create another Virtual Machine (vm4) on node2, with a vNIC on the same VNet
`myvnet2' as vm3.

Use the following network configuration for this VM:

----
auto eth0
iface eth0 inet static
        address 10.0.3.103/24
----

Then, you should be able to ping between the VMs 'vm1' and 'vm2', also
between 'vm3' and 'vm4'. But, none of VMs 'vm1' or 'vm2' can ping the VMs 'vm3'
or 'vm4', as they are on a different zone with different service-vlan.


[[pvesdn_setup_example_vxlan]]
VXLAN Setup Example
-------------------

TIP: While we show plain configuration content here, almost everything should
be configurable using the web-interface only.

node1: /etc/network/interfaces

----
auto vmbr0
iface vmbr0 inet static
	address 192.168.0.1/24
	gateway 192.168.0.254
	bridge-ports eno1
	bridge-stp off
	bridge-fd 0
	mtu 1500

source /etc/network/interfaces.d/*
----

node2: /etc/network/interfaces

----
auto vmbr0
iface vmbr0 inet static
	address 192.168.0.2/24
	gateway 192.168.0.254
	bridge-ports eno1
	bridge-stp off
	bridge-fd 0
	mtu 1500

source /etc/network/interfaces.d/*
----

node3: /etc/network/interfaces

----
auto vmbr0
iface vmbr0 inet static
	address 192.168.0.3/24
	gateway 192.168.0.254
	bridge-ports eno1
	bridge-stp off
	bridge-fd 0
	mtu 1500

source /etc/network/interfaces.d/*
----

Create an VXLAN zone named `myvxlanzone', use the lower MTU to ensure the extra
50 bytes of the VXLAN header can fit. Add all previously configured IPs from
the nodes as peer address list.

----
id: myvxlanzone
peers address list: 192.168.0.1,192.168.0.2,192.168.0.3
mtu: 1450
----

Create a VNet named `myvnet1' using the VXLAN zone `myvxlanzone' created
previously.

----
id: myvnet1
zone: myvxlanzone
tag: 100000
----

Apply the configuration on the main SDN web-interface panel to create VNets
locally on each nodes.

Create a Debian-based Virtual Machine (vm1) on node1, with a vNIC on `myvnet1'.

Use the following network configuration for this VM, note the lower MTU here.

----
auto eth0
iface eth0 inet static
        address 10.0.3.100/24
        mtu 1450
----

Create a second Virtual Machine (vm2) on node3, with a vNIC on the same VNet
`myvnet1' as vm1.

Use the following network configuration for this VM:

----
auto eth0
iface eth0 inet static
        address 10.0.3.101/24
        mtu 1450
----

Then, you should be able to ping between between 'vm1' and 'vm2'.


[[pvesdn_setup_example_evpn]]
EVPN Setup Example
------------------

node1: /etc/network/interfaces

----
auto vmbr0
iface vmbr0 inet static
	address 192.168.0.1/24
	gateway 192.168.0.254
        bridge-ports eno1
        bridge-stp off
        bridge-fd 0
	mtu 1500

source /etc/network/interfaces.d/*
----

node2: /etc/network/interfaces

----
auto vmbr0
iface vmbr0 inet static
	address 192.168.0.2/24
	gateway 192.168.0.254
        bridge-ports eno1
        bridge-stp off
        bridge-fd 0
	mtu 1500

source /etc/network/interfaces.d/*
----

node3: /etc/network/interfaces

----
auto vmbr0
iface vmbr0 inet static
	address 192.168.0.3/24
	gateway 192.168.0.254
        bridge-ports eno1
        bridge-stp off
        bridge-fd 0
	mtu 1500

source /etc/network/interfaces.d/*
----

Create a EVPN controller, using a private ASN number and above node addreesses
as peers. Define 'node1' and 'node2' as gateway nodes.

----
id: myevpnctl
asn: 65000
peers: 192.168.0.1,192.168.0.2,192.168.0.3
gateway nodes: node1,node2
----

Create an EVPN zone named `myevpnzone' using the previously created
EVPN-controller.

----
id: myevpnzone
vrf vxlan tag: 10000
controller: myevpnctl
mtu: 1450
----

Create the first VNet named `myvnet1' using the EVPN zone `myevpnzone', a IPv4
CIDR network and a random MAC address.

----
id: myvnet1
zone: myevpnzone
tag: 11000
ipv4: 10.0.1.1/24
mac address: 8C:73:B2:7B:F9:60 #random generate mac address
----

Create the second VNet named `myvnet2' using the same EVPN zone `myevpnzone', a
different IPv4 CIDR network and a different random MAC address than  `myvnet1'.

----
id: myvnet2
zone: myevpnzone
tag: 12000
ipv4: 10.0.2.1/24
mac address: 8C:73:B2:7B:F9:61  #random mac, need to be different on each vnet
----

Apply the configuration on the main SDN web-interface panel to create VNets
locally on each nodes and generate the FRR config.


Create a Debian-based Virtual Machine (vm1) on node1, with a vNIC on `myvnet1'.

Use the following network configuration for this VM:

----
auto eth0
iface eth0 inet static
        address 10.0.1.100/24
        gateway 10.0.1.1   #this is the ip of the vnet1 
        mtu 1450
----

Create a second Virtual Machine (vm2) on node2, with a vNIC on the other VNet
`myvnet2'.

Use the following network configuration for this VM:

----
auto eth0
iface eth0 inet static
        address 10.0.2.100/24
        gateway 10.0.2.1   #this is the ip of the vnet2
        mtu 1450
----


Then, you should be able to ping vm2 from vm1, and vm1 from vm2.

If you ping an external IP from 'vm2' on the non-gateway 'node3', the packet
will go to the configured 'myvnet2' gateway, then will be routed to gateway
nodes ('node1' or 'node2') and from there it will leave those nodes over the
default gateway configured on node1 or node2.

NOTE: Of course you need to add reverse routes for the '10.0.1.0/24' and
'10.0.2.0/24' network to node1, node2 on your external gateway, so that the
public network can reply back.

If you have configured an external BGP router, the BGP-EVPN routes (10.0.1.0/24
and 10.0.2.0/24 in this example), will be announced dynamically.