IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
These functions were created for poll() in 1.5-dev18 (commit 80da05a4) to
replace the previous FD_{CLR,SET,ISSET} that were shared with select()
because some libcs enforce a limit on FD_SET. But FD_SET doesn't seem
to be universally MT-safe, requiring locks in the select() code that
are not needed in the poll code. So let's move back to the initial
situation where we used to only use bit fields, since that has been in
use since day one without a problem, and let's use these hap_fd_*
functions instead of FD_*.
This patch only moves the functions to fd.h and revives hap_fd_isset()
that was recently removed to kill an "unused" warning.
Since only select() and poll() still make use of maxfd, let's move
its computation right there in the pollers themselves, and only
during each fd update pass. The computation doesn't need a lock
anymore, only a few atomic ops. It will be accurate, be done much
less often and will not be required anymore in the FD's fast patch.
This provides a small performance increase of about 1% in connection
rate when using epoll since we get rid of this computation which was
performed under a lock.
The incorrect comment was introduced in commit:
2ac5718dbd4ec722ece228e9f613d2be74eee9da
v1.5-dev9 is the first tag containing this comment, the fix
should be backported to haproxy 1.5 and newer.
Marc Fournier reported an interesting case when using threads with the
master-worker mode : sometimes, a listener would have its FD closed
during startup. Sometimes it could even be health checks seeing this.
What happens is that after the threads are created, and the pollers
enabled on each threads, the master-worker pipe is registered, and at
the same time a close() is performed on the write side of this pipe
since the children must not use it.
But since this is replicated in every thread, what happens is that the
first thread closes the pipe, thus releases the FD, and the next thread
starting a listener in parallel gets this FD reassigned. Then another
thread closes the FD again, which this time corresponds to the listener.
It can also happen with the health check sockets if they're started
early enough.
This patch splits the mworker_pipe_register() function in two, so that
the close() of the write side of the FD is performed very early after the
fork() and long before threads are created (we don't need to delay it
anyway). Only the pipe registration is done in the threaded code since
it is important that the pollers are properly allocated for this.
The mworker_pipe_register() function now takes care of registering the
pipe only once, and this is guaranteed by a new surrounding lock.
The call to protocol_enable_all() looks fragile in theory since it
scans the list of proxies and their listeners, though in practice
all threads scan the same list and take the same locks for each
listener so it's not possible that any of them escapes the process
and finishes before all listeners are started. And the operation is
idempotent.
This fix must be backported to 1.8. Thanks to Marc for providing very
detailed traces clearly showing the problem.
Some pollers like epoll() need to know if the fd is already known or
not in order to compute the operation to perform (add, mod, del). For
now this is performed based on the difference between the previous FD
state and the new state but this will not be usable anymore once threads
become responsible for their own polling.
Here we come with a different approach : a bitmask is stored with the
fd to indicate which pollers already know it, and the pollers will be
able to simply perform the add/mod/del operations based on this bit
combined with the new state.
This patch only adds the bitmask declaration and initialization, it
is it not yet used. It will be needed by the next two fixes and will
need to be backported to 1.8.
Since the fd update tables are per-thread, we need to have a bit per
thread to indicate whether an update exists, otherwise this can lead
to lost update events every time multiple threads want to update the
same FD. In practice *for now*, it only happens at start time when
listeners are enabled and ask for polling after facing their first
EAGAIN. But since the pollers are still shared, a lost event is still
recovered by a neighbor thread. This will not reliably work anymore
with per-thread pollers, where it has been observed a few times on
startup that a single-threaded listener would not always accept
incoming connections upon startup.
It's worth noting that during this code review it appeared that the
"new" flag in the fdtab isn't used anymore.
This fix should be backported to 1.8.
A bitfield has been added to know if there are some FDs processable by a
specific thread in the FD cache. When a FD is inserted in the FD cache, the bits
corresponding to its thread_mask are set. On each thread, the bitfield is
updated when the FD cache is processed. If there is no FD processed, the thread
is removed from the bitfield by unsetting its tid_bit.
Note that this bitfield is updated but not checked in
fd_process_cached_events. So, when this function is called, the FDs cache is
always processed.
[wt: should be backported to 1.8 as it will help fix a design limitation]
A number of counters have been added at special places helping better
understanding certain bug reports. These counters are maintained per
thread and are shown using "show activity" on the CLI. The "clear
counters" commands also reset these counters. The output is sent as a
single write(), which currently produces up to about 7 kB of data for
64 threads. If more counters are added, it may be necessary to write
into multiple buffers, or to reset the counters.
To backport to 1.8 to help collect more detailed bug reports.
This one allows not to inflate some structures when threads are
disabled. Now struct global is 1.4 kB instead of 33 kB.
Should be backported to 1.8 for ease of backporting of upcoming
patches.
The "thread" part is 32kB long, better move it at the end of the
structure since it's only used during initialization, to keep the
rest grouped together.
Should be backported to 1.8 to ease backporting of upcoming patches,
no functional impact.
In addition to "option force-set-var", recently added, this directive can be
used to selectivelly register unknown variable names, without totally relaxing
their registration during the runtime, like "option force-set-var" does.
So there is no way for a malicious agent to exhaust memory by defining a too
high number of variable names. In other hand, you need to enumerate all
variable names. This could be painfull in some circumstances.
Remember, this directive is only usefull when the variable names are not
referenced anywhere in the HAProxy configuration or the SPOE one.
Thanks to Etienne Carrire for his help on this part.
Commit 1a69af6d3892fe1946bb8babb3044d2d26afd46e introduced code
for atomic prior to 4.7. Unfortunately clang uses as well those
constants which is misleading.
Till now the use of __atomic_* gcc builtins required gcc >= 4.7. Since
some supported and quite common operating systems like CentOS 6 still
come with older versions (4.4) and the mapping to the older builtins
is reasonably simple, let's implement it.
This code is only used for gcc < 4.7. It has been quickly tested on a
machine using gcc 4.4.4 and provided expected results.
This patch should be backported to 1.8.
A SRV record weight can range from 0 to 65535, while haproxy weight goes
from 0 to 256, so we have to divide it by 256 before handing it to haproxy.
Also, a SRV record with a weight of 0 doesn't mean the server shouldn't be
used, so use a minimum weight of 1.
This should probably be backported to 1.8.
Since commit f9ce57e ("MEDIUM: connection: make conn_sock_shutw() aware
of lingering"), we refrain from performing the shutw() on the socket if
there is no lingering risk. But there is a problem with this in tunnel
and in TCP modes where a client is explicitly allowed to send a shutw
to the server, eventhough it it risky.
Not doing it creates this situation reported by Ricardo Fraile and
diagnosed by Christopher : a typical HTTP client (eg: curl) connecting
via the config below to an HTTP server would receive its response,
immediately close while the server remains in keep-alive mode. The
shutr() received by haproxy from the client is "propagated" to the
server side but not acted upon because fdtab[fd].linger_risk is set,
so we expect that the next close will immediately complete this
operation.
listen proxy-tcp
bind 127.0.0.1:8888
mode tcp
timeout connect 5s
timeout server 10s
timeout client 10s
server server1 127.0.0.1:8000
But since the whole stream will not end until the server closes in
turn, the server doesn't close and haproxy expires on server timeout.
This problem has already struck by waking up an older bug and was
partially fixed with commit 8059351 ("BUG/MEDIUM: http: don't disable
lingering on requests with tunnelled responses") though it was not
enough.
The problem is that linger_risk is not suited here. In fact we need to
know whether or not it is desired to close normally or silently, and
whether or not a shutr() has already been received on this connection.
This is the approach this patch takes, and it solves the problem for
the various difficult modes (tcp, http-server-close, pretend-keepalive).
This fix needs to be backported to 1.8. Many thanks to Ricardo for
providing very detailed traces and configurations.
The new function check_request_for_cacheability() is used to check if
a request may be served from the cache, and/or allows the response to
be stored into the cache. For this it checks the cache-control and
pragma header fields, and adjusts the existing TX_CACHEABLE and a new
TX_CACHE_IGNORE flags.
For now, just like its response side counterpart, it only checks the
first value of the header field. These functions should be reworked to
improve their parsers and validate all elements.
By copying the info in the stream interface that the mux cleanly reports
aborts, we'll have the ability to check this flag wherever needed regardless
of the presence of a mux or not.
This new field will be used to describe certain properties of some
muxes. For now we only add MX_FL_CLEAN_ABRT to indicate that a mux
is able to unambiguously report aborts using CS_FL_ERROR contrary
to others who may only report it via a read0. This will be used to
improve handling of the abortonclose option with H2. Other flags
may come later to report multiplexing capabilities or not, support
of client/server sides etc.
For security reasons, the spoe filter was only able to change values of
existing variables. In specific cases (ex : with LUA code), the name of
variables are unknown at the configuration parsing phase.
The force-set-var option can be enabled to register all variables.
Due to the nature of multiplexed protocols, it will often happen that
some operations are only performed on full frames, preventing any partial
operation from being performed. HTTP/2 is one such example. The current
MUX API causes a problem here because the rcv_buf() function has no way
to let the stream layer know that some data could not be read due to a
lack of room in the buffer, but that data are definitely present. The
problem with this is that the stream layer might not know it needs to
call the function again after it has made some room. And if the frame
in the buffer is not followed by any other, nothing will move anymore.
This patch introduces a new conn_stream flag CS_FL_RCV_MORE whose purpose
is to indicate on the stream that more data than what was received are
already available for reading as soon as more room will be available in
the buffer.
This patch doesn't make use of this flag yet, it only declares it. It is
expected that other similar flags may come in the future, such as reports
of pending end of stream, errors or any such event that might save the
caller from having to poll, or simply let it know that it can take some
actions after having processed data.
The thread patches adds refcount for notifications. The notifications are
used with the Lua cosocket. These refcount free the notifications when
the session is cleared. In the Lua task case, it not have sessions, so
the nofications are never cleraed.
This patch adds a garbage collector for signals. The garbage collector
just clean the notifications for which the end point is disconnected.
This patch should be backported in 1.8
The number of async fd is computed considering the maxconn, the number
of sides using ssl and the number of engines using async mode.
This patch should be backported on haproxy 1.8
In hpack_dht_make_room(), we try to fulfill this rule form RFC7541#4.4 :
"It is not an error to attempt to add an entry that is larger than the
maximum size; an attempt to add an entry larger than the maximum size
causes the table to be emptied of all existing entries and results in
an empty table."
Unfortunately it is not consistent with the way it's used in
hpack_dht_insert() as this last one will consider a success as a
confirmation it can copy the header into the table, and a failure as
an indexing error. This results in the two following issues :
- if a client sends too large a header into an empty table, this
header may overflow the table. Fortunately, most clients send
small headers like :authority first, and never mark headers that
don't fit into the table as indexable since it is counter-productive ;
- if a client sends too large a header into a populated table, the
operation fails after the table is totally flushed and the request
is not processed.
This patch fixes the two issues at once :
- a header not fitting into an empty table is always a sign that it
will never fit ;
- not fitting into the table is not an error
Thanks to Yves Lafon for reporting detailed traces demonstrating this
issue. This fix must be backported to 1.8.
If the hpack decoder sees an invalid header index, it emits value
"### ERR ###" that was used during debugging instead of rejecting the
block. This is harmless, and was detected by h2spec.
To backport to 1.8.
This BUG was introduced with:
'MEDIUM: threads/stick-tables: handle multithreads on stick tables'
The API was reviewed to handle stick table entry updates
asynchronously and the caller must now call a 'stkable_touch_*'
function each time the content of an entry is modified to
register the entry to be synced.
There was missing call to stktable_touch_* resulting in
not propagated entries to remote peers (or local one during reload)
server.h needs checks.h since it references the struct check, but depending
on the include order it will fail if check.h is included first due to this
one including server.h in turn while it doesn't need it.
Released version 1.9-dev0 with the following main changes :
- BUG/MEDIUM: stream: don't automatically forward connect nor close
- BUG/MAJOR: stream: ensure analysers are always called upon close
- BUG/MINOR: stream-int: don't try to read again when CF_READ_DONTWAIT is set
- MEDIUM: mworker: Add systemd `Type=notify` support
- BUG/MEDIUM: cache: free callback to remove from tree
- CLEANUP: cache: remove unused struct
- MEDIUM: cache: enable the HTTP analysers
- CLEANUP: cache: remove wrong comment
- MINOR: threads/atomic: rename local variables in macros to avoid conflicts
- MINOR: threads/plock: rename local variables in macros to avoid conflicts
- MINOR: threads/atomic: implement pl_mb() in asm on x86
- MINOR: threads/atomic: implement pl_bts() on non-x86
- MINOR: threads/build: atomic: replace the few inlines with macros
- BUILD: threads/plock: fix a build issue on Clang without optimization
- BUILD: ebtree: don't redefine types u32/s32 in scope-aware trees
- BUILD: compiler: add a new type modifier __maybe_unused
- BUILD: h2: mark some inlined functions "unused"
- BUILD: server: check->desc always exists
- BUG/MEDIUM: h2: properly report connection errors in headers and data handlers
- MEDIUM: h2: add a function to emit an HTTP/1 request from a headers list
- MEDIUM: h2: change hpack_decode_headers() to only provide a list of headers
- BUG/MEDIUM: h2: always reassemble the Cookie request header field
- BUG/MINOR: systemd: ignore daemon mode
- CONTRIB: spoa_example: allow to compile outside HAProxy.
- CONTRIB: spoa_example: remove bref, wordlist, cond_wordlist
- CONTRIB: spoa_example: remove last dependencies on type "sample"
- CONTRIB: spoa_example: remove SPOE enums that are useless for clients
- CLEANUP: cache: reorder includes
- MEDIUM: shctx: use unsigned int for len and block_count
- MEDIUM: cache: "show cache" on the cli
- BUG/MEDIUM: cache: use key=0 as a condition for freeing
- BUG/MEDIUM: cache: refcount forbids to free the objects
- BUG/MEDIUM: cache fix cli_kws structure
- BUG/MEDIUM: deinit: correctly deinitialize the proxy and global listener tasks
- BUG/MINOR: ssl: Always start the handshake if we can't send early data.
- MINOR: ssl: Don't disable early data handling if we could not write.
- MINOR: pools: prepare functions to override malloc/free in pools
- MINOR: pools: implement DEBUG_UAF to detect use after free
- BUG/MEDIUM: threads/time: fix time drift correction
- BUG/MEDIUM: threads/time: maintain a common time reference between all threads
- MINOR: sample: Add "thread" sample fetch
- BUG/MINOR: Use crt_base instead of ca_base when crt is parsed on a server line
- BUG/MINOR: stream: fix tv_request calculation for applets
- BUG/MAJOR: h2: always remove a stream from the send list before freeing it
- BUG/MAJOR: threads/task: dequeue expired tasks under the WQ lock
- MINOR: ssl: Handle reading early data after writing better.
- MINOR: mux: Make sure every string is woken up after the handshake.
- MEDIUM: cache: store sha1 for hashing the cache key
- MINOR: http: implement the "http-request reject" rule
- MINOR: h2: send RST_STREAM before GOAWAY on reject
- MEDIUM: h2: don't gracefully close the connection anymore on Connection: close
- MINOR: h2: make use of client-fin timeout after GOAWAY
- MEDIUM: config: ensure that tune.bufsize is at least 16384 when using HTTP/2
- MINOR: ssl: Handle early data with BoringSSL
- BUG/MEDIUM: stream: always release the stream-interface on abort
- BUG/MEDIUM: cache: free ressources in chn_end_analyze
- MINOR: cache: move the refcount decrease in the applet release
- BUG/MINOR: listener: Allow multiple "process" options on "bind" lines
- MINOR: config: Support a range to specify processes in "cpu-map" parameter
- MINOR: config: Slightly change how parse_process_number works
- MINOR: config: Export parse_process_number and use it wherever it's applicable
- MINOR: standard: Add my_ffsl function to get the position of the bit set to one
- MINOR: config: Add auto-increment feature for cpu-map
- MINOR: config: Support partial ranges in cpu-map directive
- MINOR:: config: Remove thread-map directive
- MINOR: config: Add the threads support in cpu-map directive
- MINOR: config: Add threads support for "process" option on "bind" lines
- MEDIUM: listener: Bind listeners on a thread subset if specified
- CLEANUP: debug: Use DPRINTF instead of fprintf into #ifdef DEBUG_FULL/#endif
- CLEANUP: log: Rename Alert/Warning in ha_alert/ha_warning
- MINOR/CLEANUP: proxy: rename "proxy" to "proxies_list"
- CLEANUP: pools: rename all pool functions and pointers to remove this "2"
- DOC: update the roadmap file with the latest changes merged in 1.8
- DOC: fix mangled version in peers protocol documentation
- DOC: add initial peers protovol v2.0 documentation.
- DOC: mention William as maintainer of the cache and master-worker
- DOC: add Christopher and Emeric as maintainers of the threads
- MINOR: cache: replace a fprint() by an abort()
- MEDIUM: cache: max-age configuration keyword
- DOC: explain HTTP2 timeout behavior
- DOC: cache: configuration and management
- MAJOR: mworker: exits the master on failure
- BUG/MINOR: threads: don't drop "extern" on the lock in include files
- MINOR: task: keep a pointer to the currently running task
- MINOR: task: align the rq and wq locks
- MINOR: fd: cache-align fdtab and fdcache locks
- MINOR: buffers: cache-align buffer_wq_lock
- CLEANUP: server: reorder some fields in struct server to save 40 bytes
- CLEANUP: proxy: slightly reorder the struct proxy to reduce holes
- CLEANUP: checks: remove 16 bytes of holes in struct check
- CLEANUP: cache: more efficiently pack the struct cache
- CLEANUP: fd: place the lock at the beginning of struct fdtab
- CLEANUP: pools: align pools on a cache line
- DOC: config: add a few bits about how to configure HTTP/2
- BUG/MAJOR: threads/queue: avoid recursive locking in pendconn_get_next_strm()
- BUILD: Makefile: reorder object files by size
pendconn_get_next_strm() is called from process_srv_queue() under the
server lock, and calls stream_add_srv_conn() with this lock held, while
the latter tries to take it again. This results in a deadlock when
a server's maxconn is reached and haproxy is built with thread support.
There are just a few pools, and they're stressed a lot, so it makes
sense to dedicate them a cache line to avoid contention and to place
the lock at the beginning.
The struct is not cache line aligned but at least, every time the lock
will appear in the same cache line as the fd it will benefit from being
accessed first. This improves the performance by about 2% on fd-intensive
workloads with 4 threads.
Commit 9dcf9b6 ("MINOR: threads: Use __decl_hathreads to declare locks")
accidently lost a few "extern" in certain lock declarations, possibly
causing certain entries to be declared at multiple places. Apparently
it hasn't caused any harm though.
The offending ones were :
- fdtab_lock
- fdcache_lock
- poll_lock
- buffer_wq_lock
This patch changes the behavior of the master during the exit of a
worker.
When a worker exits with an error code, for example in the case of a
segfault, all workers are now killed and the master leaves.
If you don't want this behavior you can use the option
"master-worker no-exit-on-failure".
During the migration to the second version of the pools, the new
functions and pool pointers were all called "pool_something2()" and
"pool2_something". Now there's no more pool v1 code and it's a real
pain to still have to deal with this. Let's clean this up now by
removing the "2" everywhere, and by renaming the pool heads
"pool_head_something".
Rename the global variable "proxy" to "proxies_list".
There's been multiple proxies in haproxy for quite some time, and "proxy"
is a potential source of bugs, a number of functions have a "proxy" argument,
and some code used "proxy" when it really meant "px" or "curproxy". It worked
by pure luck, because it usually happened while parsing the config, and thus
"proxy" pointed to the currently parsed proxy, but we should probably not
rely on this.
[wt: some of these are definitely fixes that are worth backporting]
It is now possible on a "bind" line (or a "stats socket" line) to specify the
thread set allowed to process listener's connections. For instance:
# HTTPS connections will be processed by all threads but the first and HTTP
# connection will be processed on the first thread.
bind *:80 process 1/1
bind *:443 ssl crt mycert.pem process 1/2-
Now, it is possible to bind CPU at the thread level instead of the process level
by defining a thread set in "cpu-map" directives. Thus, its format is now:
cpu-map [auto:]<process-set>[/<thread-set>] <cpu-set>...
where <process-set> and <thread-set> must follow the format:
all | odd | even | number[-[number]]
Having a process range and a thread range in same time with the "auto:" prefix
is not supported. Only one range is supported, the other one must be a fixed
number. But it is allowed when there is no "auto:" prefix.
Because it is possible to define a mapping for a process and another for a
thread on this process, threads will be bound on the intersection of their
mapping and the one of the process on which they are attached. If the
intersection is null, no specific binding will be set for the threads.
The prefix "auto:" can be added before the process set to let HAProxy
automatically bind a process to a CPU by incrementing process and CPU sets. To
be valid, both sets must have the same size. No matter the declaration order of
the CPU sets, it will be bound from the lower to the higher bound.
Examples:
# all these lines bind the process 1 to the cpu 0, the process 2 to cpu 1
# and so on.
cpu-map auto:1-4 0-3
cpu-map auto:1-4 0-1 2-3
cpu-map auto:1-4 3 2 1 0
# bind each process to exaclty one CPU using all/odd/even keyword
cpu-map auto:all 0-63
cpu-map auto:even 0-31
cpu-map auto:odd 32-63
# invalid cpu-map because process and CPU sets have different sizes.
cpu-map auto:1-4 0 # invalid
cpu-map auto:1 0-3 # invalid
