pinctrl: add bcm2835 driver
The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.
Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.
Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
implemented are driven by the board, not the GPIO HW block, so don't
really make sense of a HW block binding, were in general incomplete
(since they could only know about the few pins hard-coded into the
Raspberry Pi B board design and not the uncommitted GPIOS), and are
better represented simply by not writing incorrect data into pin
configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
glitches; defer this to gpio_set_direction(). Consequently, removed
empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
IRQ handler, thus fixing an issue where the code was indexing into
enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
spin_lock_irqsave() and so guarantees it doesn't run concurrently
with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
descriptive.
* Simplified remove(); removed call to non-existent
pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-09-28 08:10:11 +04:00
/*
* Driver for Broadcom BCM2835 GPIO unit ( pinctrl + GPIO )
*
* Copyright ( C ) 2012 Chris Boot , Simon Arlott , Stephen Warren
*
* This driver is inspired by :
* pinctrl - nomadik . c , please see original file for copyright information
* pinctrl - tegra . c , please see original file for copyright information
*
* This program is free software ; you can redistribute it and / or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation ; either version 2 of the License , or
* ( at your option ) any later version .
*
* This program is distributed in the hope that it will be useful ,
* but WITHOUT ANY WARRANTY ; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE . See the
* GNU General Public License for more details .
*/
# include <linux/bitmap.h>
# include <linux/bug.h>
# include <linux/delay.h>
# include <linux/device.h>
# include <linux/err.h>
# include <linux/gpio.h>
# include <linux/interrupt.h>
# include <linux/io.h>
# include <linux/irq.h>
# include <linux/irqdesc.h>
# include <linux/irqdomain.h>
# include <linux/module.h>
# include <linux/of_address.h>
# include <linux/of.h>
# include <linux/of_irq.h>
# include <linux/pinctrl/consumer.h>
# include <linux/pinctrl/machine.h>
# include <linux/pinctrl/pinconf.h>
# include <linux/pinctrl/pinctrl.h>
# include <linux/pinctrl/pinmux.h>
# include <linux/platform_device.h>
# include <linux/seq_file.h>
# include <linux/slab.h>
# include <linux/spinlock.h>
# include <linux/types.h>
# define MODULE_NAME "pinctrl-bcm2835"
# define BCM2835_NUM_GPIOS 54
# define BCM2835_NUM_BANKS 2
# define BCM2835_PIN_BITMAP_SZ \
DIV_ROUND_UP ( BCM2835_NUM_GPIOS , sizeof ( unsigned long ) * 8 )
/* GPIO register offsets */
# define GPFSEL0 0x0 /* Function Select */
# define GPSET0 0x1c /* Pin Output Set */
# define GPCLR0 0x28 /* Pin Output Clear */
# define GPLEV0 0x34 /* Pin Level */
# define GPEDS0 0x40 /* Pin Event Detect Status */
# define GPREN0 0x4c /* Pin Rising Edge Detect Enable */
# define GPFEN0 0x58 /* Pin Falling Edge Detect Enable */
# define GPHEN0 0x64 /* Pin High Detect Enable */
# define GPLEN0 0x70 /* Pin Low Detect Enable */
# define GPAREN0 0x7c /* Pin Async Rising Edge Detect */
# define GPAFEN0 0x88 /* Pin Async Falling Edge Detect */
# define GPPUD 0x94 /* Pin Pull-up/down Enable */
# define GPPUDCLK0 0x98 /* Pin Pull-up/down Enable Clock */
# define FSEL_REG(p) (GPFSEL0 + (((p) / 10) * 4))
# define FSEL_SHIFT(p) (((p) % 10) * 3)
# define GPIO_REG_OFFSET(p) ((p) / 32)
# define GPIO_REG_SHIFT(p) ((p) % 32)
enum bcm2835_pinconf_param {
/* argument: bcm2835_pinconf_pull */
BCM2835_PINCONF_PARAM_PULL ,
} ;
enum bcm2835_pinconf_pull {
BCM2835_PINCONFIG_PULL_NONE ,
BCM2835_PINCONFIG_PULL_DOWN ,
BCM2835_PINCONFIG_PULL_UP ,
} ;
# define BCM2835_PINCONF_PACK(_param_, _arg_) ((_param_) << 16 | (_arg_))
# define BCM2835_PINCONF_UNPACK_PARAM(_conf_) ((_conf_) >> 16)
# define BCM2835_PINCONF_UNPACK_ARG(_conf_) ((_conf_) & 0xffff)
struct bcm2835_gpio_irqdata {
struct bcm2835_pinctrl * pc ;
int bank ;
} ;
struct bcm2835_pinctrl {
struct device * dev ;
void __iomem * base ;
int irq [ BCM2835_NUM_BANKS ] ;
/* note: locking assumes each bank will have its own unsigned long */
unsigned long enabled_irq_map [ BCM2835_NUM_BANKS ] ;
unsigned int irq_type [ BCM2835_NUM_GPIOS ] ;
struct pinctrl_dev * pctl_dev ;
struct irq_domain * irq_domain ;
struct gpio_chip gpio_chip ;
struct pinctrl_gpio_range gpio_range ;
struct bcm2835_gpio_irqdata irq_data [ BCM2835_NUM_BANKS ] ;
spinlock_t irq_lock [ BCM2835_NUM_BANKS ] ;
} ;
static struct lock_class_key gpio_lock_class ;
/* pins are just named GPIO0..GPIO53 */
# define BCM2835_GPIO_PIN(a) PINCTRL_PIN(a, "gpio" #a)
struct pinctrl_pin_desc bcm2835_gpio_pins [ ] = {
BCM2835_GPIO_PIN ( 0 ) ,
BCM2835_GPIO_PIN ( 1 ) ,
BCM2835_GPIO_PIN ( 2 ) ,
BCM2835_GPIO_PIN ( 3 ) ,
BCM2835_GPIO_PIN ( 4 ) ,
BCM2835_GPIO_PIN ( 5 ) ,
BCM2835_GPIO_PIN ( 6 ) ,
BCM2835_GPIO_PIN ( 7 ) ,
BCM2835_GPIO_PIN ( 8 ) ,
BCM2835_GPIO_PIN ( 9 ) ,
BCM2835_GPIO_PIN ( 10 ) ,
BCM2835_GPIO_PIN ( 11 ) ,
BCM2835_GPIO_PIN ( 12 ) ,
BCM2835_GPIO_PIN ( 13 ) ,
BCM2835_GPIO_PIN ( 14 ) ,
BCM2835_GPIO_PIN ( 15 ) ,
BCM2835_GPIO_PIN ( 16 ) ,
BCM2835_GPIO_PIN ( 17 ) ,
BCM2835_GPIO_PIN ( 18 ) ,
BCM2835_GPIO_PIN ( 19 ) ,
BCM2835_GPIO_PIN ( 20 ) ,
BCM2835_GPIO_PIN ( 21 ) ,
BCM2835_GPIO_PIN ( 22 ) ,
BCM2835_GPIO_PIN ( 23 ) ,
BCM2835_GPIO_PIN ( 24 ) ,
BCM2835_GPIO_PIN ( 25 ) ,
BCM2835_GPIO_PIN ( 26 ) ,
BCM2835_GPIO_PIN ( 27 ) ,
BCM2835_GPIO_PIN ( 28 ) ,
BCM2835_GPIO_PIN ( 29 ) ,
BCM2835_GPIO_PIN ( 30 ) ,
BCM2835_GPIO_PIN ( 31 ) ,
BCM2835_GPIO_PIN ( 32 ) ,
BCM2835_GPIO_PIN ( 33 ) ,
BCM2835_GPIO_PIN ( 34 ) ,
BCM2835_GPIO_PIN ( 35 ) ,
BCM2835_GPIO_PIN ( 36 ) ,
BCM2835_GPIO_PIN ( 37 ) ,
BCM2835_GPIO_PIN ( 38 ) ,
BCM2835_GPIO_PIN ( 39 ) ,
BCM2835_GPIO_PIN ( 40 ) ,
BCM2835_GPIO_PIN ( 41 ) ,
BCM2835_GPIO_PIN ( 42 ) ,
BCM2835_GPIO_PIN ( 43 ) ,
BCM2835_GPIO_PIN ( 44 ) ,
BCM2835_GPIO_PIN ( 45 ) ,
BCM2835_GPIO_PIN ( 46 ) ,
BCM2835_GPIO_PIN ( 47 ) ,
BCM2835_GPIO_PIN ( 48 ) ,
BCM2835_GPIO_PIN ( 49 ) ,
BCM2835_GPIO_PIN ( 50 ) ,
BCM2835_GPIO_PIN ( 51 ) ,
BCM2835_GPIO_PIN ( 52 ) ,
BCM2835_GPIO_PIN ( 53 ) ,
} ;
/* one pin per group */
static const char * const bcm2835_gpio_groups [ ] = {
" gpio0 " ,
" gpio1 " ,
" gpio2 " ,
" gpio3 " ,
" gpio4 " ,
" gpio5 " ,
" gpio6 " ,
" gpio7 " ,
" gpio8 " ,
" gpio9 " ,
" gpio10 " ,
" gpio11 " ,
" gpio12 " ,
" gpio13 " ,
" gpio14 " ,
" gpio15 " ,
" gpio16 " ,
" gpio17 " ,
" gpio18 " ,
" gpio19 " ,
" gpio20 " ,
" gpio21 " ,
" gpio22 " ,
" gpio23 " ,
" gpio24 " ,
" gpio25 " ,
" gpio26 " ,
" gpio27 " ,
" gpio28 " ,
" gpio29 " ,
" gpio30 " ,
" gpio31 " ,
" gpio32 " ,
" gpio33 " ,
" gpio34 " ,
" gpio35 " ,
" gpio36 " ,
" gpio37 " ,
" gpio38 " ,
" gpio39 " ,
" gpio40 " ,
" gpio41 " ,
" gpio42 " ,
" gpio43 " ,
" gpio44 " ,
" gpio45 " ,
" gpio46 " ,
" gpio47 " ,
" gpio48 " ,
" gpio49 " ,
" gpio50 " ,
" gpio51 " ,
" gpio52 " ,
" gpio53 " ,
} ;
enum bcm2835_fsel {
BCM2835_FSEL_GPIO_IN = 0 ,
BCM2835_FSEL_GPIO_OUT = 1 ,
BCM2835_FSEL_ALT0 = 4 ,
BCM2835_FSEL_ALT1 = 5 ,
BCM2835_FSEL_ALT2 = 6 ,
BCM2835_FSEL_ALT3 = 7 ,
BCM2835_FSEL_ALT4 = 3 ,
BCM2835_FSEL_ALT5 = 2 ,
BCM2835_FSEL_COUNT = 8 ,
BCM2835_FSEL_MASK = 0x7 ,
} ;
static const char * const bcm2835_functions [ BCM2835_FSEL_COUNT ] = {
[ BCM2835_FSEL_GPIO_IN ] = " gpio_in " ,
[ BCM2835_FSEL_GPIO_OUT ] = " gpio_out " ,
[ BCM2835_FSEL_ALT0 ] = " alt0 " ,
[ BCM2835_FSEL_ALT1 ] = " alt1 " ,
[ BCM2835_FSEL_ALT2 ] = " alt2 " ,
[ BCM2835_FSEL_ALT3 ] = " alt3 " ,
[ BCM2835_FSEL_ALT4 ] = " alt4 " ,
[ BCM2835_FSEL_ALT5 ] = " alt5 " ,
} ;
static const char * const irq_type_names [ ] = {
[ IRQ_TYPE_NONE ] = " none " ,
[ IRQ_TYPE_EDGE_RISING ] = " edge-rising " ,
[ IRQ_TYPE_EDGE_FALLING ] = " edge-falling " ,
[ IRQ_TYPE_EDGE_BOTH ] = " edge-both " ,
[ IRQ_TYPE_LEVEL_HIGH ] = " level-high " ,
[ IRQ_TYPE_LEVEL_LOW ] = " level-low " ,
} ;
static inline u32 bcm2835_gpio_rd ( struct bcm2835_pinctrl * pc , unsigned reg )
{
return readl ( pc - > base + reg ) ;
}
static inline void bcm2835_gpio_wr ( struct bcm2835_pinctrl * pc , unsigned reg ,
u32 val )
{
writel ( val , pc - > base + reg ) ;
}
static inline int bcm2835_gpio_get_bit ( struct bcm2835_pinctrl * pc , unsigned reg ,
unsigned bit )
{
reg + = GPIO_REG_OFFSET ( bit ) * 4 ;
return ( bcm2835_gpio_rd ( pc , reg ) > > GPIO_REG_SHIFT ( bit ) ) & 1 ;
}
/* note NOT a read/modify/write cycle */
static inline void bcm2835_gpio_set_bit ( struct bcm2835_pinctrl * pc ,
unsigned reg , unsigned bit )
{
reg + = GPIO_REG_OFFSET ( bit ) * 4 ;
bcm2835_gpio_wr ( pc , reg , BIT ( GPIO_REG_SHIFT ( bit ) ) ) ;
}
static inline enum bcm2835_fsel bcm2835_pinctrl_fsel_get (
struct bcm2835_pinctrl * pc , unsigned pin )
{
u32 val = bcm2835_gpio_rd ( pc , FSEL_REG ( pin ) ) ;
enum bcm2835_fsel status = ( val > > FSEL_SHIFT ( pin ) ) & BCM2835_FSEL_MASK ;
dev_dbg ( pc - > dev , " get %08x (%u => %s) \n " , val , pin ,
bcm2835_functions [ status ] ) ;
return status ;
}
static inline void bcm2835_pinctrl_fsel_set (
struct bcm2835_pinctrl * pc , unsigned pin ,
enum bcm2835_fsel fsel )
{
u32 val = bcm2835_gpio_rd ( pc , FSEL_REG ( pin ) ) ;
enum bcm2835_fsel cur = ( val > > FSEL_SHIFT ( pin ) ) & BCM2835_FSEL_MASK ;
dev_dbg ( pc - > dev , " read %08x (%u => %s) \n " , val , pin ,
bcm2835_functions [ cur ] ) ;
if ( cur = = fsel )
return ;
if ( cur ! = BCM2835_FSEL_GPIO_IN & & fsel ! = BCM2835_FSEL_GPIO_IN ) {
/* always transition through GPIO_IN */
val & = ~ ( BCM2835_FSEL_MASK < < FSEL_SHIFT ( pin ) ) ;
val | = BCM2835_FSEL_GPIO_IN < < FSEL_SHIFT ( pin ) ;
dev_dbg ( pc - > dev , " trans %08x (%u <= %s) \n " , val , pin ,
bcm2835_functions [ BCM2835_FSEL_GPIO_IN ] ) ;
bcm2835_gpio_wr ( pc , FSEL_REG ( pin ) , val ) ;
}
val & = ~ ( BCM2835_FSEL_MASK < < FSEL_SHIFT ( pin ) ) ;
val | = fsel < < FSEL_SHIFT ( pin ) ;
dev_dbg ( pc - > dev , " write %08x (%u <= %s) \n " , val , pin ,
bcm2835_functions [ fsel ] ) ;
bcm2835_gpio_wr ( pc , FSEL_REG ( pin ) , val ) ;
}
static int bcm2835_gpio_request ( struct gpio_chip * chip , unsigned offset )
{
return pinctrl_request_gpio ( chip - > base + offset ) ;
}
static void bcm2835_gpio_free ( struct gpio_chip * chip , unsigned offset )
{
pinctrl_free_gpio ( chip - > base + offset ) ;
}
static int bcm2835_gpio_direction_input ( struct gpio_chip * chip , unsigned offset )
{
return pinctrl_gpio_direction_input ( chip - > base + offset ) ;
}
static int bcm2835_gpio_get ( struct gpio_chip * chip , unsigned offset )
{
struct bcm2835_pinctrl * pc = dev_get_drvdata ( chip - > dev ) ;
return bcm2835_gpio_get_bit ( pc , GPLEV0 , offset ) ;
}
static int bcm2835_gpio_direction_output ( struct gpio_chip * chip ,
unsigned offset , int value )
{
return pinctrl_gpio_direction_output ( chip - > base + offset ) ;
}
static void bcm2835_gpio_set ( struct gpio_chip * chip , unsigned offset , int value )
{
struct bcm2835_pinctrl * pc = dev_get_drvdata ( chip - > dev ) ;
bcm2835_gpio_set_bit ( pc , value ? GPSET0 : GPCLR0 , offset ) ;
}
static int bcm2835_gpio_to_irq ( struct gpio_chip * chip , unsigned offset )
{
struct bcm2835_pinctrl * pc = dev_get_drvdata ( chip - > dev ) ;
return irq_linear_revmap ( pc - > irq_domain , offset ) ;
}
2012-11-19 22:25:13 +04:00
static struct gpio_chip bcm2835_gpio_chip = {
pinctrl: add bcm2835 driver
The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.
Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.
Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
implemented are driven by the board, not the GPIO HW block, so don't
really make sense of a HW block binding, were in general incomplete
(since they could only know about the few pins hard-coded into the
Raspberry Pi B board design and not the uncommitted GPIOS), and are
better represented simply by not writing incorrect data into pin
configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
glitches; defer this to gpio_set_direction(). Consequently, removed
empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
IRQ handler, thus fixing an issue where the code was indexing into
enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
spin_lock_irqsave() and so guarantees it doesn't run concurrently
with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
descriptive.
* Simplified remove(); removed call to non-existent
pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-09-28 08:10:11 +04:00
. label = MODULE_NAME ,
. owner = THIS_MODULE ,
. request = bcm2835_gpio_request ,
. free = bcm2835_gpio_free ,
. direction_input = bcm2835_gpio_direction_input ,
. direction_output = bcm2835_gpio_direction_output ,
. get = bcm2835_gpio_get ,
. set = bcm2835_gpio_set ,
. to_irq = bcm2835_gpio_to_irq ,
. base = - 1 ,
. ngpio = BCM2835_NUM_GPIOS ,
. can_sleep = 0 ,
} ;
static irqreturn_t bcm2835_gpio_irq_handler ( int irq , void * dev_id )
{
struct bcm2835_gpio_irqdata * irqdata = dev_id ;
struct bcm2835_pinctrl * pc = irqdata - > pc ;
int bank = irqdata - > bank ;
unsigned long events ;
unsigned offset ;
unsigned gpio ;
unsigned int type ;
events = bcm2835_gpio_rd ( pc , GPEDS0 + bank * 4 ) ;
events & = pc - > enabled_irq_map [ bank ] ;
for_each_set_bit ( offset , & events , 32 ) {
gpio = ( 32 * bank ) + offset ;
type = pc - > irq_type [ gpio ] ;
/* ack edge triggered IRQs immediately */
if ( ! ( type & IRQ_TYPE_LEVEL_MASK ) )
bcm2835_gpio_set_bit ( pc , GPEDS0 , gpio ) ;
generic_handle_irq ( irq_linear_revmap ( pc - > irq_domain , gpio ) ) ;
/* ack level triggered IRQ after handling them */
if ( type & IRQ_TYPE_LEVEL_MASK )
bcm2835_gpio_set_bit ( pc , GPEDS0 , gpio ) ;
}
return events ? IRQ_HANDLED : IRQ_NONE ;
}
static inline void __bcm2835_gpio_irq_config ( struct bcm2835_pinctrl * pc ,
unsigned reg , unsigned offset , bool enable )
{
u32 value ;
reg + = GPIO_REG_OFFSET ( offset ) * 4 ;
value = bcm2835_gpio_rd ( pc , reg ) ;
if ( enable )
value | = BIT ( GPIO_REG_SHIFT ( offset ) ) ;
else
value & = ~ ( BIT ( GPIO_REG_SHIFT ( offset ) ) ) ;
bcm2835_gpio_wr ( pc , reg , value ) ;
}
/* fast path for IRQ handler */
static void bcm2835_gpio_irq_config ( struct bcm2835_pinctrl * pc ,
unsigned offset , bool enable )
{
switch ( pc - > irq_type [ offset ] ) {
case IRQ_TYPE_EDGE_RISING :
__bcm2835_gpio_irq_config ( pc , GPREN0 , offset , enable ) ;
break ;
case IRQ_TYPE_EDGE_FALLING :
__bcm2835_gpio_irq_config ( pc , GPFEN0 , offset , enable ) ;
break ;
case IRQ_TYPE_EDGE_BOTH :
__bcm2835_gpio_irq_config ( pc , GPREN0 , offset , enable ) ;
__bcm2835_gpio_irq_config ( pc , GPFEN0 , offset , enable ) ;
break ;
case IRQ_TYPE_LEVEL_HIGH :
__bcm2835_gpio_irq_config ( pc , GPHEN0 , offset , enable ) ;
break ;
case IRQ_TYPE_LEVEL_LOW :
__bcm2835_gpio_irq_config ( pc , GPLEN0 , offset , enable ) ;
break ;
}
}
static void bcm2835_gpio_irq_enable ( struct irq_data * data )
{
struct bcm2835_pinctrl * pc = irq_data_get_irq_chip_data ( data ) ;
unsigned gpio = irqd_to_hwirq ( data ) ;
unsigned offset = GPIO_REG_SHIFT ( gpio ) ;
unsigned bank = GPIO_REG_OFFSET ( gpio ) ;
unsigned long flags ;
spin_lock_irqsave ( & pc - > irq_lock [ bank ] , flags ) ;
set_bit ( offset , & pc - > enabled_irq_map [ bank ] ) ;
bcm2835_gpio_irq_config ( pc , gpio , true ) ;
spin_unlock_irqrestore ( & pc - > irq_lock [ bank ] , flags ) ;
}
static void bcm2835_gpio_irq_disable ( struct irq_data * data )
{
struct bcm2835_pinctrl * pc = irq_data_get_irq_chip_data ( data ) ;
unsigned gpio = irqd_to_hwirq ( data ) ;
unsigned offset = GPIO_REG_SHIFT ( gpio ) ;
unsigned bank = GPIO_REG_OFFSET ( gpio ) ;
unsigned long flags ;
spin_lock_irqsave ( & pc - > irq_lock [ bank ] , flags ) ;
bcm2835_gpio_irq_config ( pc , gpio , false ) ;
clear_bit ( offset , & pc - > enabled_irq_map [ bank ] ) ;
spin_unlock_irqrestore ( & pc - > irq_lock [ bank ] , flags ) ;
}
static int __bcm2835_gpio_irq_set_type_disabled ( struct bcm2835_pinctrl * pc ,
unsigned offset , unsigned int type )
{
switch ( type ) {
case IRQ_TYPE_NONE :
case IRQ_TYPE_EDGE_RISING :
case IRQ_TYPE_EDGE_FALLING :
case IRQ_TYPE_EDGE_BOTH :
case IRQ_TYPE_LEVEL_HIGH :
case IRQ_TYPE_LEVEL_LOW :
pc - > irq_type [ offset ] = type ;
break ;
default :
return - EINVAL ;
}
return 0 ;
}
/* slower path for reconfiguring IRQ type */
static int __bcm2835_gpio_irq_set_type_enabled ( struct bcm2835_pinctrl * pc ,
unsigned offset , unsigned int type )
{
switch ( type ) {
case IRQ_TYPE_NONE :
if ( pc - > irq_type [ offset ] ! = type ) {
bcm2835_gpio_irq_config ( pc , offset , false ) ;
pc - > irq_type [ offset ] = type ;
}
break ;
case IRQ_TYPE_EDGE_RISING :
if ( pc - > irq_type [ offset ] = = IRQ_TYPE_EDGE_BOTH ) {
/* RISING already enabled, disable FALLING */
pc - > irq_type [ offset ] = IRQ_TYPE_EDGE_FALLING ;
bcm2835_gpio_irq_config ( pc , offset , false ) ;
pc - > irq_type [ offset ] = type ;
} else if ( pc - > irq_type [ offset ] ! = type ) {
bcm2835_gpio_irq_config ( pc , offset , false ) ;
pc - > irq_type [ offset ] = type ;
bcm2835_gpio_irq_config ( pc , offset , true ) ;
}
break ;
case IRQ_TYPE_EDGE_FALLING :
if ( pc - > irq_type [ offset ] = = IRQ_TYPE_EDGE_BOTH ) {
/* FALLING already enabled, disable RISING */
pc - > irq_type [ offset ] = IRQ_TYPE_EDGE_RISING ;
bcm2835_gpio_irq_config ( pc , offset , false ) ;
pc - > irq_type [ offset ] = type ;
} else if ( pc - > irq_type [ offset ] ! = type ) {
bcm2835_gpio_irq_config ( pc , offset , false ) ;
pc - > irq_type [ offset ] = type ;
bcm2835_gpio_irq_config ( pc , offset , true ) ;
}
break ;
case IRQ_TYPE_EDGE_BOTH :
if ( pc - > irq_type [ offset ] = = IRQ_TYPE_EDGE_RISING ) {
/* RISING already enabled, enable FALLING too */
pc - > irq_type [ offset ] = IRQ_TYPE_EDGE_FALLING ;
bcm2835_gpio_irq_config ( pc , offset , true ) ;
pc - > irq_type [ offset ] = type ;
} else if ( pc - > irq_type [ offset ] = = IRQ_TYPE_EDGE_FALLING ) {
/* FALLING already enabled, enable RISING too */
pc - > irq_type [ offset ] = IRQ_TYPE_EDGE_RISING ;
bcm2835_gpio_irq_config ( pc , offset , true ) ;
pc - > irq_type [ offset ] = type ;
} else if ( pc - > irq_type [ offset ] ! = type ) {
bcm2835_gpio_irq_config ( pc , offset , false ) ;
pc - > irq_type [ offset ] = type ;
bcm2835_gpio_irq_config ( pc , offset , true ) ;
}
break ;
case IRQ_TYPE_LEVEL_HIGH :
case IRQ_TYPE_LEVEL_LOW :
if ( pc - > irq_type [ offset ] ! = type ) {
bcm2835_gpio_irq_config ( pc , offset , false ) ;
pc - > irq_type [ offset ] = type ;
bcm2835_gpio_irq_config ( pc , offset , true ) ;
}
break ;
default :
return - EINVAL ;
}
return 0 ;
}
static int bcm2835_gpio_irq_set_type ( struct irq_data * data , unsigned int type )
{
struct bcm2835_pinctrl * pc = irq_data_get_irq_chip_data ( data ) ;
unsigned gpio = irqd_to_hwirq ( data ) ;
unsigned offset = GPIO_REG_SHIFT ( gpio ) ;
unsigned bank = GPIO_REG_OFFSET ( gpio ) ;
unsigned long flags ;
int ret ;
spin_lock_irqsave ( & pc - > irq_lock [ bank ] , flags ) ;
if ( test_bit ( offset , & pc - > enabled_irq_map [ bank ] ) )
ret = __bcm2835_gpio_irq_set_type_enabled ( pc , gpio , type ) ;
else
ret = __bcm2835_gpio_irq_set_type_disabled ( pc , gpio , type ) ;
spin_unlock_irqrestore ( & pc - > irq_lock [ bank ] , flags ) ;
return ret ;
}
static struct irq_chip bcm2835_gpio_irq_chip = {
. name = MODULE_NAME ,
. irq_enable = bcm2835_gpio_irq_enable ,
. irq_disable = bcm2835_gpio_irq_disable ,
. irq_set_type = bcm2835_gpio_irq_set_type ,
} ;
static int bcm2835_pctl_get_groups_count ( struct pinctrl_dev * pctldev )
{
return ARRAY_SIZE ( bcm2835_gpio_groups ) ;
}
static const char * bcm2835_pctl_get_group_name ( struct pinctrl_dev * pctldev ,
unsigned selector )
{
return bcm2835_gpio_groups [ selector ] ;
}
static int bcm2835_pctl_get_group_pins ( struct pinctrl_dev * pctldev ,
unsigned selector ,
const unsigned * * pins ,
unsigned * num_pins )
{
* pins = & bcm2835_gpio_pins [ selector ] . number ;
* num_pins = 1 ;
return 0 ;
}
static void bcm2835_pctl_pin_dbg_show ( struct pinctrl_dev * pctldev ,
struct seq_file * s ,
unsigned offset )
{
struct bcm2835_pinctrl * pc = pinctrl_dev_get_drvdata ( pctldev ) ;
enum bcm2835_fsel fsel = bcm2835_pinctrl_fsel_get ( pc , offset ) ;
const char * fname = bcm2835_functions [ fsel ] ;
int value = bcm2835_gpio_get_bit ( pc , GPLEV0 , offset ) ;
int irq = irq_find_mapping ( pc - > irq_domain , offset ) ;
seq_printf ( s , " function %s in %s; irq %d (%s) " ,
fname , value ? " hi " : " lo " ,
irq , irq_type_names [ pc - > irq_type [ offset ] ] ) ;
}
static void bcm2835_pctl_dt_free_map ( struct pinctrl_dev * pctldev ,
struct pinctrl_map * maps , unsigned num_maps )
{
int i ;
for ( i = 0 ; i < num_maps ; i + + )
if ( maps [ i ] . type = = PIN_MAP_TYPE_CONFIGS_PIN )
kfree ( maps [ i ] . data . configs . configs ) ;
kfree ( maps ) ;
}
static int bcm2835_pctl_dt_node_to_map_func ( struct bcm2835_pinctrl * pc ,
struct device_node * np , u32 pin , u32 fnum ,
struct pinctrl_map * * maps )
{
struct pinctrl_map * map = * maps ;
if ( fnum > = ARRAY_SIZE ( bcm2835_functions ) ) {
dev_err ( pc - > dev , " %s: invalid brcm,function %d \n " ,
of_node_full_name ( np ) , fnum ) ;
return - EINVAL ;
}
map - > type = PIN_MAP_TYPE_MUX_GROUP ;
map - > data . mux . group = bcm2835_gpio_groups [ pin ] ;
map - > data . mux . function = bcm2835_functions [ fnum ] ;
( * maps ) + + ;
return 0 ;
}
static int bcm2835_pctl_dt_node_to_map_pull ( struct bcm2835_pinctrl * pc ,
struct device_node * np , u32 pin , u32 pull ,
struct pinctrl_map * * maps )
{
struct pinctrl_map * map = * maps ;
unsigned long * configs ;
if ( pull > 2 ) {
dev_err ( pc - > dev , " %s: invalid brcm,pull %d \n " ,
of_node_full_name ( np ) , pull ) ;
return - EINVAL ;
}
configs = kzalloc ( sizeof ( * configs ) , GFP_KERNEL ) ;
if ( ! configs )
return - ENOMEM ;
configs [ 0 ] = BCM2835_PINCONF_PACK ( BCM2835_PINCONF_PARAM_PULL , pull ) ;
map - > type = PIN_MAP_TYPE_CONFIGS_PIN ;
map - > data . configs . group_or_pin = bcm2835_gpio_pins [ pin ] . name ;
map - > data . configs . configs = configs ;
map - > data . configs . num_configs = 1 ;
( * maps ) + + ;
return 0 ;
}
static inline u32 prop_u32 ( struct property * p , int i )
{
return be32_to_cpup ( ( ( __be32 * ) p - > value ) + i ) ;
}
static int bcm2835_pctl_dt_node_to_map ( struct pinctrl_dev * pctldev ,
struct device_node * np ,
struct pinctrl_map * * map , unsigned * num_maps )
{
struct bcm2835_pinctrl * pc = pinctrl_dev_get_drvdata ( pctldev ) ;
struct property * pins , * funcs , * pulls ;
int num_pins , num_funcs , num_pulls , maps_per_pin ;
struct pinctrl_map * maps , * cur_map ;
int i , err ;
u32 pin , func , pull ;
pins = of_find_property ( np , " brcm,pins " , NULL ) ;
if ( ! pins ) {
dev_err ( pc - > dev , " %s: missing brcm,pins property \n " ,
of_node_full_name ( np ) ) ;
return - EINVAL ;
}
funcs = of_find_property ( np , " brcm,function " , NULL ) ;
pulls = of_find_property ( np , " brcm,pull " , NULL ) ;
if ( ! funcs & & ! pulls ) {
dev_err ( pc - > dev ,
" %s: neither brcm,function nor brcm,pull specified \n " ,
of_node_full_name ( np ) ) ;
return - EINVAL ;
}
num_pins = pins - > length / 4 ;
num_funcs = funcs ? ( funcs - > length / 4 ) : 0 ;
num_pulls = pulls ? ( pulls - > length / 4 ) : 0 ;
if ( num_funcs > 1 & & num_funcs ! = num_pins ) {
dev_err ( pc - > dev ,
" %s: brcm,function must have 1 or %d entries \n " ,
of_node_full_name ( np ) , num_pins ) ;
return - EINVAL ;
}
if ( num_pulls > 1 & & num_pulls ! = num_pins ) {
dev_err ( pc - > dev ,
" %s: brcm,pull must have 1 or %d entries \n " ,
of_node_full_name ( np ) , num_pins ) ;
return - EINVAL ;
}
maps_per_pin = 0 ;
if ( num_funcs )
maps_per_pin + + ;
if ( num_pulls )
maps_per_pin + + ;
cur_map = maps = kzalloc ( num_pins * maps_per_pin * sizeof ( * maps ) ,
GFP_KERNEL ) ;
if ( ! maps )
return - ENOMEM ;
for ( i = 0 ; i < num_pins ; i + + ) {
pin = prop_u32 ( pins , i ) ;
if ( pin > = ARRAY_SIZE ( bcm2835_gpio_pins ) ) {
dev_err ( pc - > dev , " %s: invalid brcm,pins value %d \n " ,
of_node_full_name ( np ) , pin ) ;
err = - EINVAL ;
goto out ;
}
if ( num_funcs ) {
func = prop_u32 ( funcs , ( num_funcs > 1 ) ? i : 0 ) ;
err = bcm2835_pctl_dt_node_to_map_func ( pc , np , pin ,
func , & cur_map ) ;
if ( err )
goto out ;
}
if ( num_pulls ) {
pull = prop_u32 ( pulls , ( num_pulls > 1 ) ? i : 0 ) ;
err = bcm2835_pctl_dt_node_to_map_pull ( pc , np , pin ,
pull , & cur_map ) ;
if ( err )
goto out ;
}
}
* map = maps ;
* num_maps = num_pins * maps_per_pin ;
return 0 ;
out :
kfree ( maps ) ;
return err ;
}
static struct pinctrl_ops bcm2835_pctl_ops = {
. get_groups_count = bcm2835_pctl_get_groups_count ,
. get_group_name = bcm2835_pctl_get_group_name ,
. get_group_pins = bcm2835_pctl_get_group_pins ,
. pin_dbg_show = bcm2835_pctl_pin_dbg_show ,
. dt_node_to_map = bcm2835_pctl_dt_node_to_map ,
. dt_free_map = bcm2835_pctl_dt_free_map ,
} ;
static int bcm2835_pmx_get_functions_count ( struct pinctrl_dev * pctldev )
{
return BCM2835_FSEL_COUNT ;
}
static const char * bcm2835_pmx_get_function_name ( struct pinctrl_dev * pctldev ,
unsigned selector )
{
return bcm2835_functions [ selector ] ;
}
static int bcm2835_pmx_get_function_groups ( struct pinctrl_dev * pctldev ,
unsigned selector ,
const char * const * * groups ,
unsigned * const num_groups )
{
/* every pin can do every function */
* groups = bcm2835_gpio_groups ;
* num_groups = ARRAY_SIZE ( bcm2835_gpio_groups ) ;
return 0 ;
}
static int bcm2835_pmx_enable ( struct pinctrl_dev * pctldev ,
unsigned func_selector ,
unsigned group_selector )
{
struct bcm2835_pinctrl * pc = pinctrl_dev_get_drvdata ( pctldev ) ;
bcm2835_pinctrl_fsel_set ( pc , group_selector , func_selector ) ;
return 0 ;
}
static void bcm2835_pmx_disable ( struct pinctrl_dev * pctldev ,
unsigned func_selector ,
unsigned group_selector )
{
struct bcm2835_pinctrl * pc = pinctrl_dev_get_drvdata ( pctldev ) ;
/* disable by setting to GPIO_IN */
bcm2835_pinctrl_fsel_set ( pc , group_selector , BCM2835_FSEL_GPIO_IN ) ;
}
static void bcm2835_pmx_gpio_disable_free ( struct pinctrl_dev * pctldev ,
struct pinctrl_gpio_range * range ,
unsigned offset )
{
struct bcm2835_pinctrl * pc = pinctrl_dev_get_drvdata ( pctldev ) ;
/* disable by setting to GPIO_IN */
bcm2835_pinctrl_fsel_set ( pc , offset , BCM2835_FSEL_GPIO_IN ) ;
}
static int bcm2835_pmx_gpio_set_direction ( struct pinctrl_dev * pctldev ,
struct pinctrl_gpio_range * range ,
unsigned offset ,
bool input )
{
struct bcm2835_pinctrl * pc = pinctrl_dev_get_drvdata ( pctldev ) ;
enum bcm2835_fsel fsel = input ?
BCM2835_FSEL_GPIO_IN : BCM2835_FSEL_GPIO_OUT ;
bcm2835_pinctrl_fsel_set ( pc , offset , fsel ) ;
return 0 ;
}
static struct pinmux_ops bcm2835_pmx_ops = {
. get_functions_count = bcm2835_pmx_get_functions_count ,
. get_function_name = bcm2835_pmx_get_function_name ,
. get_function_groups = bcm2835_pmx_get_function_groups ,
. enable = bcm2835_pmx_enable ,
. disable = bcm2835_pmx_disable ,
. gpio_disable_free = bcm2835_pmx_gpio_disable_free ,
. gpio_set_direction = bcm2835_pmx_gpio_set_direction ,
} ;
static int bcm2835_pinconf_get ( struct pinctrl_dev * pctldev ,
unsigned pin , unsigned long * config )
{
/* No way to read back config in HW */
return - ENOTSUPP ;
}
static int bcm2835_pinconf_set ( struct pinctrl_dev * pctldev ,
unsigned pin , unsigned long config )
{
struct bcm2835_pinctrl * pc = pinctrl_dev_get_drvdata ( pctldev ) ;
enum bcm2835_pinconf_param param = BCM2835_PINCONF_UNPACK_PARAM ( config ) ;
u16 arg = BCM2835_PINCONF_UNPACK_ARG ( config ) ;
u32 off , bit ;
if ( param ! = BCM2835_PINCONF_PARAM_PULL )
return - EINVAL ;
off = GPIO_REG_OFFSET ( pin ) ;
bit = GPIO_REG_SHIFT ( pin ) ;
bcm2835_gpio_wr ( pc , GPPUD , arg & 3 ) ;
/*
* Docs say to wait 150 cycles , but not of what . We assume a
* 1 MHz clock here , which is pretty slow . . .
*/
udelay ( 150 ) ;
bcm2835_gpio_wr ( pc , GPPUDCLK0 + ( off * 4 ) , BIT ( bit ) ) ;
udelay ( 150 ) ;
bcm2835_gpio_wr ( pc , GPPUDCLK0 + ( off * 4 ) , 0 ) ;
return 0 ;
}
2012-11-07 09:37:08 +04:00
static struct pinconf_ops bcm2835_pinconf_ops = {
pinctrl: add bcm2835 driver
The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.
Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.
Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
implemented are driven by the board, not the GPIO HW block, so don't
really make sense of a HW block binding, were in general incomplete
(since they could only know about the few pins hard-coded into the
Raspberry Pi B board design and not the uncommitted GPIOS), and are
better represented simply by not writing incorrect data into pin
configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
glitches; defer this to gpio_set_direction(). Consequently, removed
empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
IRQ handler, thus fixing an issue where the code was indexing into
enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
spin_lock_irqsave() and so guarantees it doesn't run concurrently
with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
descriptive.
* Simplified remove(); removed call to non-existent
pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-09-28 08:10:11 +04:00
. pin_config_get = bcm2835_pinconf_get ,
. pin_config_set = bcm2835_pinconf_set ,
} ;
static struct pinctrl_desc bcm2835_pinctrl_desc = {
. name = MODULE_NAME ,
. pins = bcm2835_gpio_pins ,
. npins = ARRAY_SIZE ( bcm2835_gpio_pins ) ,
. pctlops = & bcm2835_pctl_ops ,
. pmxops = & bcm2835_pmx_ops ,
. confops = & bcm2835_pinconf_ops ,
. owner = THIS_MODULE ,
} ;
2012-11-19 22:25:13 +04:00
static struct pinctrl_gpio_range bcm2835_pinctrl_gpio_range = {
pinctrl: add bcm2835 driver
The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.
Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.
Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
implemented are driven by the board, not the GPIO HW block, so don't
really make sense of a HW block binding, were in general incomplete
(since they could only know about the few pins hard-coded into the
Raspberry Pi B board design and not the uncommitted GPIOS), and are
better represented simply by not writing incorrect data into pin
configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
glitches; defer this to gpio_set_direction(). Consequently, removed
empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
IRQ handler, thus fixing an issue where the code was indexing into
enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
spin_lock_irqsave() and so guarantees it doesn't run concurrently
with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
descriptive.
* Simplified remove(); removed call to non-existent
pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-09-28 08:10:11 +04:00
. name = MODULE_NAME ,
. npins = BCM2835_NUM_GPIOS ,
} ;
2012-12-22 01:10:23 +04:00
static int bcm2835_pinctrl_probe ( struct platform_device * pdev )
pinctrl: add bcm2835 driver
The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.
Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.
Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
implemented are driven by the board, not the GPIO HW block, so don't
really make sense of a HW block binding, were in general incomplete
(since they could only know about the few pins hard-coded into the
Raspberry Pi B board design and not the uncommitted GPIOS), and are
better represented simply by not writing incorrect data into pin
configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
glitches; defer this to gpio_set_direction(). Consequently, removed
empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
IRQ handler, thus fixing an issue where the code was indexing into
enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
spin_lock_irqsave() and so guarantees it doesn't run concurrently
with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
descriptive.
* Simplified remove(); removed call to non-existent
pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-09-28 08:10:11 +04:00
{
struct device * dev = & pdev - > dev ;
struct device_node * np = dev - > of_node ;
struct bcm2835_pinctrl * pc ;
struct resource iomem ;
int err , i ;
BUILD_BUG_ON ( ARRAY_SIZE ( bcm2835_gpio_pins ) ! = BCM2835_NUM_GPIOS ) ;
BUILD_BUG_ON ( ARRAY_SIZE ( bcm2835_gpio_groups ) ! = BCM2835_NUM_GPIOS ) ;
pc = devm_kzalloc ( dev , sizeof ( * pc ) , GFP_KERNEL ) ;
if ( ! pc )
return - ENOMEM ;
platform_set_drvdata ( pdev , pc ) ;
pc - > dev = dev ;
err = of_address_to_resource ( np , 0 , & iomem ) ;
if ( err ) {
dev_err ( dev , " could not get IO memory \n " ) ;
return err ;
}
2012-10-08 13:40:36 +04:00
pc - > base = devm_request_and_ioremap ( dev , & iomem ) ;
pinctrl: add bcm2835 driver
The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.
Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.
Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
implemented are driven by the board, not the GPIO HW block, so don't
really make sense of a HW block binding, were in general incomplete
(since they could only know about the few pins hard-coded into the
Raspberry Pi B board design and not the uncommitted GPIOS), and are
better represented simply by not writing incorrect data into pin
configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
glitches; defer this to gpio_set_direction(). Consequently, removed
empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
IRQ handler, thus fixing an issue where the code was indexing into
enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
spin_lock_irqsave() and so guarantees it doesn't run concurrently
with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
descriptive.
* Simplified remove(); removed call to non-existent
pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-09-28 08:10:11 +04:00
if ( ! pc - > base )
return - EADDRNOTAVAIL ;
pc - > gpio_chip = bcm2835_gpio_chip ;
pc - > gpio_chip . dev = dev ;
pc - > gpio_chip . of_node = np ;
pc - > irq_domain = irq_domain_add_linear ( np , BCM2835_NUM_GPIOS ,
& irq_domain_simple_ops , NULL ) ;
if ( ! pc - > irq_domain ) {
dev_err ( dev , " could not create IRQ domain \n " ) ;
return - ENOMEM ;
}
for ( i = 0 ; i < BCM2835_NUM_GPIOS ; i + + ) {
int irq = irq_create_mapping ( pc - > irq_domain , i ) ;
irq_set_lockdep_class ( irq , & gpio_lock_class ) ;
irq_set_chip_and_handler ( irq , & bcm2835_gpio_irq_chip ,
handle_simple_irq ) ;
irq_set_chip_data ( irq , pc ) ;
set_irq_flags ( irq , IRQF_VALID ) ;
}
for ( i = 0 ; i < BCM2835_NUM_BANKS ; i + + ) {
unsigned long events ;
unsigned offset ;
int len ;
char * name ;
/* clear event detection flags */
bcm2835_gpio_wr ( pc , GPREN0 + i * 4 , 0 ) ;
bcm2835_gpio_wr ( pc , GPFEN0 + i * 4 , 0 ) ;
bcm2835_gpio_wr ( pc , GPHEN0 + i * 4 , 0 ) ;
bcm2835_gpio_wr ( pc , GPLEN0 + i * 4 , 0 ) ;
bcm2835_gpio_wr ( pc , GPAREN0 + i * 4 , 0 ) ;
bcm2835_gpio_wr ( pc , GPAFEN0 + i * 4 , 0 ) ;
/* clear all the events */
events = bcm2835_gpio_rd ( pc , GPEDS0 + i * 4 ) ;
for_each_set_bit ( offset , & events , 32 )
bcm2835_gpio_wr ( pc , GPEDS0 + i * 4 , BIT ( offset ) ) ;
pc - > irq [ i ] = irq_of_parse_and_map ( np , i ) ;
pc - > irq_data [ i ] . pc = pc ;
pc - > irq_data [ i ] . bank = i ;
spin_lock_init ( & pc - > irq_lock [ i ] ) ;
len = strlen ( dev_name ( pc - > dev ) ) + 16 ;
name = devm_kzalloc ( pc - > dev , len , GFP_KERNEL ) ;
if ( ! name )
return - ENOMEM ;
snprintf ( name , len , " %s:bank%d " , dev_name ( pc - > dev ) , i ) ;
err = devm_request_irq ( dev , pc - > irq [ i ] ,
bcm2835_gpio_irq_handler , IRQF_SHARED ,
name , & pc - > irq_data [ i ] ) ;
if ( err ) {
dev_err ( dev , " unable to request IRQ %d \n " , pc - > irq [ i ] ) ;
return err ;
}
}
err = gpiochip_add ( & pc - > gpio_chip ) ;
if ( err ) {
dev_err ( dev , " could not add GPIO chip \n " ) ;
return err ;
}
pc - > pctl_dev = pinctrl_register ( & bcm2835_pinctrl_desc , dev , pc ) ;
if ( ! pc - > pctl_dev ) {
gpiochip_remove ( & pc - > gpio_chip ) ;
2012-10-07 18:01:15 +04:00
return - EINVAL ;
pinctrl: add bcm2835 driver
The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.
Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.
Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
implemented are driven by the board, not the GPIO HW block, so don't
really make sense of a HW block binding, were in general incomplete
(since they could only know about the few pins hard-coded into the
Raspberry Pi B board design and not the uncommitted GPIOS), and are
better represented simply by not writing incorrect data into pin
configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
glitches; defer this to gpio_set_direction(). Consequently, removed
empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
IRQ handler, thus fixing an issue where the code was indexing into
enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
spin_lock_irqsave() and so guarantees it doesn't run concurrently
with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
descriptive.
* Simplified remove(); removed call to non-existent
pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-09-28 08:10:11 +04:00
}
pc - > gpio_range = bcm2835_pinctrl_gpio_range ;
pc - > gpio_range . base = pc - > gpio_chip . base ;
pc - > gpio_range . gc = & pc - > gpio_chip ;
pinctrl_add_gpio_range ( pc - > pctl_dev , & pc - > gpio_range ) ;
return 0 ;
}
2012-11-19 22:26:06 +04:00
static int bcm2835_pinctrl_remove ( struct platform_device * pdev )
pinctrl: add bcm2835 driver
The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.
Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.
Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
implemented are driven by the board, not the GPIO HW block, so don't
really make sense of a HW block binding, were in general incomplete
(since they could only know about the few pins hard-coded into the
Raspberry Pi B board design and not the uncommitted GPIOS), and are
better represented simply by not writing incorrect data into pin
configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
glitches; defer this to gpio_set_direction(). Consequently, removed
empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
IRQ handler, thus fixing an issue where the code was indexing into
enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
spin_lock_irqsave() and so guarantees it doesn't run concurrently
with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
descriptive.
* Simplified remove(); removed call to non-existent
pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-09-28 08:10:11 +04:00
{
struct bcm2835_pinctrl * pc = platform_get_drvdata ( pdev ) ;
pinctrl_unregister ( pc - > pctl_dev ) ;
gpiochip_remove ( & pc - > gpio_chip ) ;
return 0 ;
}
2012-11-19 22:25:13 +04:00
static struct of_device_id bcm2835_pinctrl_match [ ] = {
pinctrl: add bcm2835 driver
The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.
Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.
Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
implemented are driven by the board, not the GPIO HW block, so don't
really make sense of a HW block binding, were in general incomplete
(since they could only know about the few pins hard-coded into the
Raspberry Pi B board design and not the uncommitted GPIOS), and are
better represented simply by not writing incorrect data into pin
configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
glitches; defer this to gpio_set_direction(). Consequently, removed
empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
IRQ handler, thus fixing an issue where the code was indexing into
enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
spin_lock_irqsave() and so guarantees it doesn't run concurrently
with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
descriptive.
* Simplified remove(); removed call to non-existent
pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-09-28 08:10:11 +04:00
{ . compatible = " brcm,bcm2835-gpio " } ,
{ }
} ;
MODULE_DEVICE_TABLE ( of , bcm2835_pinctrl_match ) ;
static struct platform_driver bcm2835_pinctrl_driver = {
. probe = bcm2835_pinctrl_probe ,
. remove = bcm2835_pinctrl_remove ,
. driver = {
. name = MODULE_NAME ,
. owner = THIS_MODULE ,
. of_match_table = bcm2835_pinctrl_match ,
} ,
} ;
module_platform_driver ( bcm2835_pinctrl_driver ) ;
MODULE_AUTHOR ( " Chris Boot, Simon Arlott, Stephen Warren " ) ;
MODULE_DESCRIPTION ( " BCM2835 Pin control driver " ) ;
MODULE_LICENSE ( " GPL " ) ;