hwmon: add driver for Aquacomputer D5 Next
This driver exposes hardware sensors of the Aquacomputer D5 Next
watercooling pump, which communicates through a proprietary USB HID
protocol.
Available sensors are pump and fan speed, power, voltage and current, as
well as coolant temperature. Also available through debugfs are the serial
number, firmware version and power-on count.
Attaching a fan is optional and allows it to be controlled using
temperature curves directly from the pump. If it's not connected,
the fan-related sensors will report zeroes.
The pump can be configured either through software or via its physical
interface. Configuring the pump through this driver is not implemented,
as it seems to require sending it a complete configuration. That
includes addressable RGB LEDs, for which there is no standard sysfs
interface. Thus, that task is better suited for userspace tools.
This driver has been tested on x86_64, both in-kernel and as a module.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2021-08-28 07:26:28 +02:00
.. SPDX-License-Identifier: GPL-2.0-or-later
Kernel driver aquacomputer-d5next
=================================
Supported devices:
* Aquacomputer D5 Next watercooling pump
2022-02-27 21:56:25 +01:00
* Aquacomputer Farbwerk 360 RGB controller
hwmon: add driver for Aquacomputer D5 Next
This driver exposes hardware sensors of the Aquacomputer D5 Next
watercooling pump, which communicates through a proprietary USB HID
protocol.
Available sensors are pump and fan speed, power, voltage and current, as
well as coolant temperature. Also available through debugfs are the serial
number, firmware version and power-on count.
Attaching a fan is optional and allows it to be controlled using
temperature curves directly from the pump. If it's not connected,
the fan-related sensors will report zeroes.
The pump can be configured either through software or via its physical
interface. Configuring the pump through this driver is not implemented,
as it seems to require sending it a complete configuration. That
includes addressable RGB LEDs, for which there is no standard sysfs
interface. Thus, that task is better suited for userspace tools.
This driver has been tested on x86_64, both in-kernel and as a module.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2021-08-28 07:26:28 +02:00
Author: Aleksa Savic
Description
-----------
2022-02-27 21:56:25 +01:00
This driver exposes hardware sensors of listed Aquacomputer devices, which
communicate through proprietary USB HID protocols.
hwmon: add driver for Aquacomputer D5 Next
This driver exposes hardware sensors of the Aquacomputer D5 Next
watercooling pump, which communicates through a proprietary USB HID
protocol.
Available sensors are pump and fan speed, power, voltage and current, as
well as coolant temperature. Also available through debugfs are the serial
number, firmware version and power-on count.
Attaching a fan is optional and allows it to be controlled using
temperature curves directly from the pump. If it's not connected,
the fan-related sensors will report zeroes.
The pump can be configured either through software or via its physical
interface. Configuring the pump through this driver is not implemented,
as it seems to require sending it a complete configuration. That
includes addressable RGB LEDs, for which there is no standard sysfs
interface. Thus, that task is better suited for userspace tools.
This driver has been tested on x86_64, both in-kernel and as a module.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2021-08-28 07:26:28 +02:00
2022-02-27 21:56:25 +01:00
For the D5 Next pump, available sensors are pump and fan speed, power, voltage
and current, as well as coolant temperature. Also available through debugfs are
the serial number, firmware version and power-on count. Attaching a fan to it is
optional and allows it to be controlled using temperature curves directly from the
pump. If it's not connected, the fan-related sensors will report zeroes.
hwmon: add driver for Aquacomputer D5 Next
This driver exposes hardware sensors of the Aquacomputer D5 Next
watercooling pump, which communicates through a proprietary USB HID
protocol.
Available sensors are pump and fan speed, power, voltage and current, as
well as coolant temperature. Also available through debugfs are the serial
number, firmware version and power-on count.
Attaching a fan is optional and allows it to be controlled using
temperature curves directly from the pump. If it's not connected,
the fan-related sensors will report zeroes.
The pump can be configured either through software or via its physical
interface. Configuring the pump through this driver is not implemented,
as it seems to require sending it a complete configuration. That
includes addressable RGB LEDs, for which there is no standard sysfs
interface. Thus, that task is better suited for userspace tools.
This driver has been tested on x86_64, both in-kernel and as a module.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2021-08-28 07:26:28 +02:00
The pump can be configured either through software or via its physical
interface. Configuring the pump through this driver is not implemented, as it
seems to require sending it a complete configuration. That includes addressable
RGB LEDs, for which there is no standard sysfs interface. Thus, that task is
better suited for userspace tools.
2022-02-27 21:56:25 +01:00
The Farbwerk 360 exposes four temperature sensors. Depending on the device,
not all sysfs and debugfs entries will be available.
hwmon: add driver for Aquacomputer D5 Next
This driver exposes hardware sensors of the Aquacomputer D5 Next
watercooling pump, which communicates through a proprietary USB HID
protocol.
Available sensors are pump and fan speed, power, voltage and current, as
well as coolant temperature. Also available through debugfs are the serial
number, firmware version and power-on count.
Attaching a fan is optional and allows it to be controlled using
temperature curves directly from the pump. If it's not connected,
the fan-related sensors will report zeroes.
The pump can be configured either through software or via its physical
interface. Configuring the pump through this driver is not implemented,
as it seems to require sending it a complete configuration. That
includes addressable RGB LEDs, for which there is no standard sysfs
interface. Thus, that task is better suited for userspace tools.
This driver has been tested on x86_64, both in-kernel and as a module.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2021-08-28 07:26:28 +02:00
Usage notes
-----------
2022-02-27 21:56:25 +01:00
The devices communicate via HID reports. The driver is loaded automatically by
hwmon: add driver for Aquacomputer D5 Next
This driver exposes hardware sensors of the Aquacomputer D5 Next
watercooling pump, which communicates through a proprietary USB HID
protocol.
Available sensors are pump and fan speed, power, voltage and current, as
well as coolant temperature. Also available through debugfs are the serial
number, firmware version and power-on count.
Attaching a fan is optional and allows it to be controlled using
temperature curves directly from the pump. If it's not connected,
the fan-related sensors will report zeroes.
The pump can be configured either through software or via its physical
interface. Configuring the pump through this driver is not implemented,
as it seems to require sending it a complete configuration. That
includes addressable RGB LEDs, for which there is no standard sysfs
interface. Thus, that task is better suited for userspace tools.
This driver has been tested on x86_64, both in-kernel and as a module.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2021-08-28 07:26:28 +02:00
the kernel and supports hotswapping.
Sysfs entries
-------------
2022-02-27 21:56:25 +01:00
================ =============================================
temp[1-4]_ input Temperature sensors (in millidegrees Celsius)
fan[1-2]_ input Pump/fan speed (in RPM)
power[1-2]_ input Pump/fan power (in micro Watts)
in[0-2]_ input Pump/fan voltage (in milli Volts)
curr[1-2]_ input Pump/fan current (in milli Amperes)
================ =============================================
hwmon: add driver for Aquacomputer D5 Next
This driver exposes hardware sensors of the Aquacomputer D5 Next
watercooling pump, which communicates through a proprietary USB HID
protocol.
Available sensors are pump and fan speed, power, voltage and current, as
well as coolant temperature. Also available through debugfs are the serial
number, firmware version and power-on count.
Attaching a fan is optional and allows it to be controlled using
temperature curves directly from the pump. If it's not connected,
the fan-related sensors will report zeroes.
The pump can be configured either through software or via its physical
interface. Configuring the pump through this driver is not implemented,
as it seems to require sending it a complete configuration. That
includes addressable RGB LEDs, for which there is no standard sysfs
interface. Thus, that task is better suited for userspace tools.
This driver has been tested on x86_64, both in-kernel and as a module.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2021-08-28 07:26:28 +02:00
Debugfs entries
---------------
2022-02-27 21:56:25 +01:00
================ =================================================
serial_number Serial number of the device
hwmon: add driver for Aquacomputer D5 Next
This driver exposes hardware sensors of the Aquacomputer D5 Next
watercooling pump, which communicates through a proprietary USB HID
protocol.
Available sensors are pump and fan speed, power, voltage and current, as
well as coolant temperature. Also available through debugfs are the serial
number, firmware version and power-on count.
Attaching a fan is optional and allows it to be controlled using
temperature curves directly from the pump. If it's not connected,
the fan-related sensors will report zeroes.
The pump can be configured either through software or via its physical
interface. Configuring the pump through this driver is not implemented,
as it seems to require sending it a complete configuration. That
includes addressable RGB LEDs, for which there is no standard sysfs
interface. Thus, that task is better suited for userspace tools.
This driver has been tested on x86_64, both in-kernel and as a module.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2021-08-28 07:26:28 +02:00
firmware_version Version of installed firmware
2022-02-27 21:56:25 +01:00
power_cycles Count of how many times the device was powered on
================ =================================================
