iv/linux
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
254c80a3a0
linux/drivers/usb/host/xhci-dbg.c

471 lines
14 KiB
C
Raw Normal View History

USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
/*
* xHCI host controller driver
*
* Copyright (C) 2008 Intel Corp.
*
* Author: Sarah Sharp
* Some code borrowed from the Linux EHCI driver.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software Foundation,
* Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include "xhci.h"
#define XHCI_INIT_VALUE 0x0
/* Add verbose debugging later, just print everything for now */
void xhci_dbg_regs(struct xhci_hcd *xhci)
{
u32 temp;
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "// xHCI capability registers at %p:\n",
xhci->cap_regs);
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
temp = xhci_readl(xhci, &xhci->cap_regs->hc_capbase);
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "// @%p = 0x%x (CAPLENGTH AND HCIVERSION)\n",
&xhci->cap_regs->hc_capbase, temp);
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
xhci_dbg(xhci, "// CAPLENGTH: 0x%x\n",
(unsigned int) HC_LENGTH(temp));
#if 0
xhci_dbg(xhci, "// HCIVERSION: 0x%x\n",
(unsigned int) HC_VERSION(temp));
#endif
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "// xHCI operational registers at %p:\n", xhci->op_regs);
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
temp = xhci_readl(xhci, &xhci->cap_regs->run_regs_off);
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "// @%p = 0x%x RTSOFF\n",
&xhci->cap_regs->run_regs_off,
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
(unsigned int) temp & RTSOFF_MASK);
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "// xHCI runtime registers at %p:\n", xhci->run_regs);
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
temp = xhci_readl(xhci, &xhci->cap_regs->db_off);
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "// @%p = 0x%x DBOFF\n", &xhci->cap_regs->db_off, temp);
xhci_dbg(xhci, "// Doorbell array at %p:\n", xhci->dba);
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
}
USB: xhci: Avoid global namespace pollution. Make all globally visible functions start with xhci_ and mark functions as static if they're only called within the same C file. Fix some long lines while we're at it. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:05:20 +04:00
static void xhci_print_cap_regs(struct xhci_hcd *xhci)
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
{
u32 temp;
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "xHCI capability registers at %p:\n", xhci->cap_regs);
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
temp = xhci_readl(xhci, &xhci->cap_regs->hc_capbase);
xhci_dbg(xhci, "CAPLENGTH AND HCIVERSION 0x%x:\n",
(unsigned int) temp);
xhci_dbg(xhci, "CAPLENGTH: 0x%x\n",
(unsigned int) HC_LENGTH(temp));
xhci_dbg(xhci, "HCIVERSION: 0x%x\n",
(unsigned int) HC_VERSION(temp));
temp = xhci_readl(xhci, &xhci->cap_regs->hcs_params1);
xhci_dbg(xhci, "HCSPARAMS 1: 0x%x\n",
(unsigned int) temp);
xhci_dbg(xhci, " Max device slots: %u\n",
(unsigned int) HCS_MAX_SLOTS(temp));
xhci_dbg(xhci, " Max interrupters: %u\n",
(unsigned int) HCS_MAX_INTRS(temp));
xhci_dbg(xhci, " Max ports: %u\n",
(unsigned int) HCS_MAX_PORTS(temp));
temp = xhci_readl(xhci, &xhci->cap_regs->hcs_params2);
xhci_dbg(xhci, "HCSPARAMS 2: 0x%x\n",
(unsigned int) temp);
xhci_dbg(xhci, " Isoc scheduling threshold: %u\n",
(unsigned int) HCS_IST(temp));
xhci_dbg(xhci, " Maximum allowed segments in event ring: %u\n",
(unsigned int) HCS_ERST_MAX(temp));
temp = xhci_readl(xhci, &xhci->cap_regs->hcs_params3);
xhci_dbg(xhci, "HCSPARAMS 3 0x%x:\n",
(unsigned int) temp);
xhci_dbg(xhci, " Worst case U1 device exit latency: %u\n",
(unsigned int) HCS_U1_LATENCY(temp));
xhci_dbg(xhci, " Worst case U2 device exit latency: %u\n",
(unsigned int) HCS_U2_LATENCY(temp));
temp = xhci_readl(xhci, &xhci->cap_regs->hcc_params);
xhci_dbg(xhci, "HCC PARAMS 0x%x:\n", (unsigned int) temp);
xhci_dbg(xhci, " HC generates %s bit addresses\n",
HCC_64BIT_ADDR(temp) ? "64" : "32");
/* FIXME */
xhci_dbg(xhci, " FIXME: more HCCPARAMS debugging\n");
temp = xhci_readl(xhci, &xhci->cap_regs->run_regs_off);
xhci_dbg(xhci, "RTSOFF 0x%x:\n", temp & RTSOFF_MASK);
}
USB: xhci: Avoid global namespace pollution. Make all globally visible functions start with xhci_ and mark functions as static if they're only called within the same C file. Fix some long lines while we're at it. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:05:20 +04:00
static void xhci_print_command_reg(struct xhci_hcd *xhci)
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
{
u32 temp;
temp = xhci_readl(xhci, &xhci->op_regs->command);
xhci_dbg(xhci, "USBCMD 0x%x:\n", temp);
xhci_dbg(xhci, " HC is %s\n",
(temp & CMD_RUN) ? "running" : "being stopped");
xhci_dbg(xhci, " HC has %sfinished hard reset\n",
(temp & CMD_RESET) ? "not " : "");
xhci_dbg(xhci, " Event Interrupts %s\n",
(temp & CMD_EIE) ? "enabled " : "disabled");
xhci_dbg(xhci, " Host System Error Interrupts %s\n",
(temp & CMD_EIE) ? "enabled " : "disabled");
xhci_dbg(xhci, " HC has %sfinished light reset\n",
(temp & CMD_LRESET) ? "not " : "");
}
USB: xhci: Avoid global namespace pollution. Make all globally visible functions start with xhci_ and mark functions as static if they're only called within the same C file. Fix some long lines while we're at it. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:05:20 +04:00
static void xhci_print_status(struct xhci_hcd *xhci)
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
{
u32 temp;
temp = xhci_readl(xhci, &xhci->op_regs->status);
xhci_dbg(xhci, "USBSTS 0x%x:\n", temp);
xhci_dbg(xhci, " Event ring is %sempty\n",
(temp & STS_EINT) ? "not " : "");
xhci_dbg(xhci, " %sHost System Error\n",
(temp & STS_FATAL) ? "WARNING: " : "No ");
xhci_dbg(xhci, " HC is %s\n",
(temp & STS_HALT) ? "halted" : "running");
}
USB: xhci: Avoid global namespace pollution. Make all globally visible functions start with xhci_ and mark functions as static if they're only called within the same C file. Fix some long lines while we're at it. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:05:20 +04:00
static void xhci_print_op_regs(struct xhci_hcd *xhci)
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
{
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "xHCI operational registers at %p:\n", xhci->op_regs);
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
xhci_print_command_reg(xhci);
xhci_print_status(xhci);
}
USB: xhci: Avoid global namespace pollution. Make all globally visible functions start with xhci_ and mark functions as static if they're only called within the same C file. Fix some long lines while we're at it. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:05:20 +04:00
static void xhci_print_ports(struct xhci_hcd *xhci)
USB: xhci: Root hub support. Add functionality for getting port status and hub descriptor for xHCI root hubs. This is WIP because the USB 3.0 hub descriptor is different from the USB 2.0 hub descriptor. For now, we lie about the root hub descriptor because the changes won't effect how the core talks to the root hub. Later we will need to add the USB 3.0 hub descriptor for real hubs, and this code might change. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:57:12 +04:00
{
u32 __iomem *addr;
int i, j;
int ports;
char *names[NUM_PORT_REGS] = {
"status",
"power",
"link",
"reserved",
};
ports = HCS_MAX_PORTS(xhci->hcs_params1);
addr = &xhci->op_regs->port_status_base;
for (i = 0; i < ports; i++) {
for (j = 0; j < NUM_PORT_REGS; ++j) {
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "%p port %s reg = 0x%x\n",
addr, names[j],
USB: xhci: Root hub support. Add functionality for getting port status and hub descriptor for xHCI root hubs. This is WIP because the USB 3.0 hub descriptor is different from the USB 2.0 hub descriptor. For now, we lie about the root hub descriptor because the changes won't effect how the core talks to the root hub. Later we will need to add the USB 3.0 hub descriptor for real hubs, and this code might change. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:57:12 +04:00
(unsigned int) xhci_readl(xhci, addr));
addr++;
}
}
}
USB: xhci: Remove packed attribute from structures. The packed attribute allows gcc to muck with the alignment of data structures, which may lead to byte-wise writes that break atomicity of writes. Packed should only be used when the compile may add undesired padding to the structure. Each element of the structure will be aligned by C based on its size and the size of the elements around it. E.g. a u64 would be aligned on an 8 byte boundary, the next u32 would be aligned on a four byte boundary, etc. Since most of the xHCI structures contain only u32 bit values, removing the packed attribute for them should be harmless. (A future patch will change some of the twin 32-bit address fields to one 64-bit field, but all those places have an even number of 32-bit fields before them, so the alignment should be correct.) Add BUILD_BUG_ON statements to check that the compiler doesn't add padding to the data structures that have a hardware-defined layout. While we're modifying the registers, change the name of intr_reg to xhci_intr_reg to avoid global conflicts. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-05-14 22:44:18 +04:00
void xhci_print_ir_set(struct xhci_hcd *xhci, struct xhci_intr_reg *ir_set, int set_num)
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
{
void *addr;
u32 temp;
USB: xhci: Represent 64-bit addresses with one u64. There are several xHCI data structures that use two 32-bit fields to represent a 64-bit address. Since some architectures don't support 64-bit PCI writes, the fields need to be written in two 32-bit writes. The xHCI specification says that if a platform is incapable of generating 64-bit writes, software must write the low 32-bits first, then the high 32-bits. Hardware that supports 64-bit addressing will wait for the high 32-bit write before reading the revised value, and hardware that only supports 32-bit writes will ignore the high 32-bit write. Previous xHCI code represented 64-bit addresses with two u32 values. This lead to buggy code that would write the 32-bits in the wrong order, or forget to write the upper 32-bits. Change the two u32s to one u64 and create a function call to write all 64-bit addresses in the proper order. This new function could be modified in the future if all platforms support 64-bit writes. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-07-27 23:03:31 +04:00
u64 temp_64;
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
addr = &ir_set->irq_pending;
temp = xhci_readl(xhci, addr);
if (temp == XHCI_INIT_VALUE)
return;
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, " %p: ir_set[%i]\n", ir_set, set_num);
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, " %p: ir_set.pending = 0x%x\n", addr,
(unsigned int)temp);
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
addr = &ir_set->irq_control;
temp = xhci_readl(xhci, addr);
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, " %p: ir_set.control = 0x%x\n", addr,
(unsigned int)temp);
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
addr = &ir_set->erst_size;
temp = xhci_readl(xhci, addr);
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, " %p: ir_set.erst_size = 0x%x\n", addr,
(unsigned int)temp);
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
addr = &ir_set->rsvd;
temp = xhci_readl(xhci, addr);
if (temp != XHCI_INIT_VALUE)
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, " WARN: %p: ir_set.rsvd = 0x%x\n",
addr, (unsigned int)temp);
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
USB: xhci: Represent 64-bit addresses with one u64. There are several xHCI data structures that use two 32-bit fields to represent a 64-bit address. Since some architectures don't support 64-bit PCI writes, the fields need to be written in two 32-bit writes. The xHCI specification says that if a platform is incapable of generating 64-bit writes, software must write the low 32-bits first, then the high 32-bits. Hardware that supports 64-bit addressing will wait for the high 32-bit write before reading the revised value, and hardware that only supports 32-bit writes will ignore the high 32-bit write. Previous xHCI code represented 64-bit addresses with two u32 values. This lead to buggy code that would write the 32-bits in the wrong order, or forget to write the upper 32-bits. Change the two u32s to one u64 and create a function call to write all 64-bit addresses in the proper order. This new function could be modified in the future if all platforms support 64-bit writes. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-07-27 23:03:31 +04:00
addr = &ir_set->erst_base;
temp_64 = xhci_read_64(xhci, addr);
xhci_dbg(xhci, " %p: ir_set.erst_base = @%08llx\n",
addr, temp_64);
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
USB: xhci: Represent 64-bit addresses with one u64. There are several xHCI data structures that use two 32-bit fields to represent a 64-bit address. Since some architectures don't support 64-bit PCI writes, the fields need to be written in two 32-bit writes. The xHCI specification says that if a platform is incapable of generating 64-bit writes, software must write the low 32-bits first, then the high 32-bits. Hardware that supports 64-bit addressing will wait for the high 32-bit write before reading the revised value, and hardware that only supports 32-bit writes will ignore the high 32-bit write. Previous xHCI code represented 64-bit addresses with two u32 values. This lead to buggy code that would write the 32-bits in the wrong order, or forget to write the upper 32-bits. Change the two u32s to one u64 and create a function call to write all 64-bit addresses in the proper order. This new function could be modified in the future if all platforms support 64-bit writes. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-07-27 23:03:31 +04:00
addr = &ir_set->erst_dequeue;
temp_64 = xhci_read_64(xhci, addr);
xhci_dbg(xhci, " %p: ir_set.erst_dequeue = @%08llx\n",
addr, temp_64);
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
}
void xhci_print_run_regs(struct xhci_hcd *xhci)
{
u32 temp;
int i;
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "xHCI runtime registers at %p:\n", xhci->run_regs);
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
temp = xhci_readl(xhci, &xhci->run_regs->microframe_index);
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, " %p: Microframe index = 0x%x\n",
&xhci->run_regs->microframe_index,
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
(unsigned int) temp);
for (i = 0; i < 7; ++i) {
temp = xhci_readl(xhci, &xhci->run_regs->rsvd[i]);
if (temp != XHCI_INIT_VALUE)
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, " WARN: %p: Rsvd[%i] = 0x%x\n",
&xhci->run_regs->rsvd[i],
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
i, (unsigned int) temp);
}
}
void xhci_print_registers(struct xhci_hcd *xhci)
{
xhci_print_cap_regs(xhci);
xhci_print_op_regs(xhci);
USB: xhci: Root hub support. Add functionality for getting port status and hub descriptor for xHCI root hubs. This is WIP because the USB 3.0 hub descriptor is different from the USB 2.0 hub descriptor. For now, we lie about the root hub descriptor because the changes won't effect how the core talks to the root hub. Later we will need to add the USB 3.0 hub descriptor for real hubs, and this code might change. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:57:12 +04:00
xhci_print_ports(xhci);
USB: xhci: Support xHCI host controllers and USB 3.0 devices. This is the first of many patches to add support for USB 3.0 devices and the hardware that implements the eXtensible Host Controller Interface (xHCI) 0.95 specification. This specification is not yet publicly available, but companies can receive a copy by becoming an xHCI Contributor (see http://www.intel.com/technology/usb/xhcispec.htm). No xHCI hardware has made it onto the market yet, but these patches have been tested under the Fresco Logic host controller prototype. This patch adds the xHCI register sets, which are grouped into five sets: - Generic PCI registers - Host controller "capabilities" registers (cap_regs) short - Host controller "operational" registers (op_regs) - Host controller "runtime" registers (run_regs) - Host controller "doorbell" registers These some of these registers may be virtualized if the Linux driver is running under a VM. Virtualization has not been tested for this patch. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:22 +04:00
}
USB: xhci: Ring allocation and initialization. Allocate basic xHCI host controller data structures. For every xHC, there is a command ring, an event ring, and a doorbell array. The doorbell array is used to notify the host controller that work has been enqueued onto one of the rings. The host controller driver enqueues commands on the command ring. The HW enqueues command completion events on the event ring and interrupts the system (currently using PCI interrupts, although the xHCI HW will use MSI interrupts eventually). All rings and the doorbell array must be allocated by the xHCI host controller driver. Each ring is comprised of one or more segments, which consists of 16-byte Transfer Request Blocks (TRBs) that can be chained to form a Transfer Descriptor (TD) that represents a multiple-buffer request. Segments are linked into a ring using Link TRBs, which means they are dynamically growable. The producer of the ring enqueues a TD by writing one or more TRBs in the ring and toggling the TRB cycle bit for each TRB. The consumer knows it can process the TRB when the cycle bit matches its internal consumer cycle state for the ring. The consumer cycle state is toggled an odd amount of times in the ring. An example ring (a ring must have a minimum of 16 TRBs on it, but that's too big to draw in ASCII art): chain cycle bit bit ------------------------ | TD A TRB 1 | 1 | 1 |<------------- <-- consumer dequeue ptr ------------------------ | consumer cycle state = 1 | TD A TRB 2 | 1 | 1 | | ------------------------ | | TD A TRB 3 | 0 | 1 | segment 1 | ------------------------ | | TD B TRB 1 | 1 | 1 | | ------------------------ | | TD B TRB 2 | 0 | 1 | | ------------------------ | | Link TRB | 0 | 1 |----- | ------------------------ | | | | chain cycle | | bit bit | | ------------------------ | | | TD C TRB 1 | 0 | 1 |<---- | ------------------------ | | TD D TRB 1 | 1 | 1 | | ------------------------ | | TD D TRB 2 | 1 | 1 | segment 2 | ------------------------ | | TD D TRB 3 | 1 | 1 | | ------------------------ | | TD D TRB 4 | 1 | 1 | | ------------------------ | | Link TRB | 1 | 1 |----- | ------------------------ | | | | chain cycle | | bit bit | | ------------------------ | | | TD D TRB 5 | 1 | 1 |<---- | ------------------------ | | TD D TRB 6 | 0 | 1 | | ------------------------ | | TD E TRB 1 | 0 | 1 | segment 3 | ------------------------ | | | 0 | 0 | | <-- producer enqueue ptr ------------------------ | | | 0 | 0 | | ------------------------ | | Link TRB | 0 | 0 |--------------- ------------------------ Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:34 +04:00
USB: xhci: No-op command queueing and irq handler. xHCI host controllers can optionally implement a no-op test. This simple test ensures the OS has correctly setup all basic data structures and can correctly respond to interrupts from the host controller hardware. There are two rings exercised by the no-op test: the command ring, and the event ring. The host controller driver writes a no-op command TRB to the command ring, and rings the doorbell for the command ring (the first entry in the doorbell array). The hardware receives this event, places a command completion event on the event ring, and fires an interrupt. The host controller driver sees the interrupt, and checks the event ring for TRBs it can process, and sees the command completion event. (See the rules in xhci-ring.c for who "owns" a TRB. This is a simplified set of rules, and may not contain all the details that are in the xHCI 0.95 spec.) A timer fires every 60 seconds to debug the state of the hardware and command and event rings. This timer only runs if CONFIG_USB_XHCI_HCD_DEBUGGING is 'y'. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:53:56 +04:00
void xhci_print_trb_offsets(struct xhci_hcd *xhci, union xhci_trb *trb)
{
int i;
for (i = 0; i < 4; ++i)
xhci_dbg(xhci, "Offset 0x%x = 0x%x\n",
i*4, trb->generic.field[i]);
}
/**
* Debug a transfer request block (TRB).
*/
void xhci_debug_trb(struct xhci_hcd *xhci, union xhci_trb *trb)
{
u64 address;
u32 type = xhci_readl(xhci, &trb->link.control) & TRB_TYPE_BITMASK;
switch (type) {
case TRB_TYPE(TRB_LINK):
xhci_dbg(xhci, "Link TRB:\n");
xhci_print_trb_offsets(xhci, trb);
USB: xhci: Represent 64-bit addresses with one u64. There are several xHCI data structures that use two 32-bit fields to represent a 64-bit address. Since some architectures don't support 64-bit PCI writes, the fields need to be written in two 32-bit writes. The xHCI specification says that if a platform is incapable of generating 64-bit writes, software must write the low 32-bits first, then the high 32-bits. Hardware that supports 64-bit addressing will wait for the high 32-bit write before reading the revised value, and hardware that only supports 32-bit writes will ignore the high 32-bit write. Previous xHCI code represented 64-bit addresses with two u32 values. This lead to buggy code that would write the 32-bits in the wrong order, or forget to write the upper 32-bits. Change the two u32s to one u64 and create a function call to write all 64-bit addresses in the proper order. This new function could be modified in the future if all platforms support 64-bit writes. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-07-27 23:03:31 +04:00
address = trb->link.segment_ptr;
USB: xhci: No-op command queueing and irq handler. xHCI host controllers can optionally implement a no-op test. This simple test ensures the OS has correctly setup all basic data structures and can correctly respond to interrupts from the host controller hardware. There are two rings exercised by the no-op test: the command ring, and the event ring. The host controller driver writes a no-op command TRB to the command ring, and rings the doorbell for the command ring (the first entry in the doorbell array). The hardware receives this event, places a command completion event on the event ring, and fires an interrupt. The host controller driver sees the interrupt, and checks the event ring for TRBs it can process, and sees the command completion event. (See the rules in xhci-ring.c for who "owns" a TRB. This is a simplified set of rules, and may not contain all the details that are in the xHCI 0.95 spec.) A timer fires every 60 seconds to debug the state of the hardware and command and event rings. This timer only runs if CONFIG_USB_XHCI_HCD_DEBUGGING is 'y'. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:53:56 +04:00
xhci_dbg(xhci, "Next ring segment DMA address = 0x%llx\n", address);
xhci_dbg(xhci, "Interrupter target = 0x%x\n",
GET_INTR_TARGET(trb->link.intr_target));
xhci_dbg(xhci, "Cycle bit = %u\n",
(unsigned int) (trb->link.control & TRB_CYCLE));
xhci_dbg(xhci, "Toggle cycle bit = %u\n",
(unsigned int) (trb->link.control & LINK_TOGGLE));
xhci_dbg(xhci, "No Snoop bit = %u\n",
(unsigned int) (trb->link.control & TRB_NO_SNOOP));
break;
case TRB_TYPE(TRB_TRANSFER):
USB: xhci: Represent 64-bit addresses with one u64. There are several xHCI data structures that use two 32-bit fields to represent a 64-bit address. Since some architectures don't support 64-bit PCI writes, the fields need to be written in two 32-bit writes. The xHCI specification says that if a platform is incapable of generating 64-bit writes, software must write the low 32-bits first, then the high 32-bits. Hardware that supports 64-bit addressing will wait for the high 32-bit write before reading the revised value, and hardware that only supports 32-bit writes will ignore the high 32-bit write. Previous xHCI code represented 64-bit addresses with two u32 values. This lead to buggy code that would write the 32-bits in the wrong order, or forget to write the upper 32-bits. Change the two u32s to one u64 and create a function call to write all 64-bit addresses in the proper order. This new function could be modified in the future if all platforms support 64-bit writes. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-07-27 23:03:31 +04:00
address = trb->trans_event.buffer;
USB: xhci: No-op command queueing and irq handler. xHCI host controllers can optionally implement a no-op test. This simple test ensures the OS has correctly setup all basic data structures and can correctly respond to interrupts from the host controller hardware. There are two rings exercised by the no-op test: the command ring, and the event ring. The host controller driver writes a no-op command TRB to the command ring, and rings the doorbell for the command ring (the first entry in the doorbell array). The hardware receives this event, places a command completion event on the event ring, and fires an interrupt. The host controller driver sees the interrupt, and checks the event ring for TRBs it can process, and sees the command completion event. (See the rules in xhci-ring.c for who "owns" a TRB. This is a simplified set of rules, and may not contain all the details that are in the xHCI 0.95 spec.) A timer fires every 60 seconds to debug the state of the hardware and command and event rings. This timer only runs if CONFIG_USB_XHCI_HCD_DEBUGGING is 'y'. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:53:56 +04:00
/*
* FIXME: look at flags to figure out if it's an address or if
* the data is directly in the buffer field.
*/
xhci_dbg(xhci, "DMA address or buffer contents= %llu\n", address);
break;
case TRB_TYPE(TRB_COMPLETION):
USB: xhci: Represent 64-bit addresses with one u64. There are several xHCI data structures that use two 32-bit fields to represent a 64-bit address. Since some architectures don't support 64-bit PCI writes, the fields need to be written in two 32-bit writes. The xHCI specification says that if a platform is incapable of generating 64-bit writes, software must write the low 32-bits first, then the high 32-bits. Hardware that supports 64-bit addressing will wait for the high 32-bit write before reading the revised value, and hardware that only supports 32-bit writes will ignore the high 32-bit write. Previous xHCI code represented 64-bit addresses with two u32 values. This lead to buggy code that would write the 32-bits in the wrong order, or forget to write the upper 32-bits. Change the two u32s to one u64 and create a function call to write all 64-bit addresses in the proper order. This new function could be modified in the future if all platforms support 64-bit writes. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-07-27 23:03:31 +04:00
address = trb->event_cmd.cmd_trb;
USB: xhci: No-op command queueing and irq handler. xHCI host controllers can optionally implement a no-op test. This simple test ensures the OS has correctly setup all basic data structures and can correctly respond to interrupts from the host controller hardware. There are two rings exercised by the no-op test: the command ring, and the event ring. The host controller driver writes a no-op command TRB to the command ring, and rings the doorbell for the command ring (the first entry in the doorbell array). The hardware receives this event, places a command completion event on the event ring, and fires an interrupt. The host controller driver sees the interrupt, and checks the event ring for TRBs it can process, and sees the command completion event. (See the rules in xhci-ring.c for who "owns" a TRB. This is a simplified set of rules, and may not contain all the details that are in the xHCI 0.95 spec.) A timer fires every 60 seconds to debug the state of the hardware and command and event rings. This timer only runs if CONFIG_USB_XHCI_HCD_DEBUGGING is 'y'. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:53:56 +04:00
xhci_dbg(xhci, "Command TRB pointer = %llu\n", address);
xhci_dbg(xhci, "Completion status = %u\n",
(unsigned int) GET_COMP_CODE(trb->event_cmd.status));
xhci_dbg(xhci, "Flags = 0x%x\n", (unsigned int) trb->event_cmd.flags);
break;
default:
xhci_dbg(xhci, "Unknown TRB with TRB type ID %u\n",
(unsigned int) type>>10);
xhci_print_trb_offsets(xhci, trb);
break;
}
}
USB: xhci: Ring allocation and initialization. Allocate basic xHCI host controller data structures. For every xHC, there is a command ring, an event ring, and a doorbell array. The doorbell array is used to notify the host controller that work has been enqueued onto one of the rings. The host controller driver enqueues commands on the command ring. The HW enqueues command completion events on the event ring and interrupts the system (currently using PCI interrupts, although the xHCI HW will use MSI interrupts eventually). All rings and the doorbell array must be allocated by the xHCI host controller driver. Each ring is comprised of one or more segments, which consists of 16-byte Transfer Request Blocks (TRBs) that can be chained to form a Transfer Descriptor (TD) that represents a multiple-buffer request. Segments are linked into a ring using Link TRBs, which means they are dynamically growable. The producer of the ring enqueues a TD by writing one or more TRBs in the ring and toggling the TRB cycle bit for each TRB. The consumer knows it can process the TRB when the cycle bit matches its internal consumer cycle state for the ring. The consumer cycle state is toggled an odd amount of times in the ring. An example ring (a ring must have a minimum of 16 TRBs on it, but that's too big to draw in ASCII art): chain cycle bit bit ------------------------ | TD A TRB 1 | 1 | 1 |<------------- <-- consumer dequeue ptr ------------------------ | consumer cycle state = 1 | TD A TRB 2 | 1 | 1 | | ------------------------ | | TD A TRB 3 | 0 | 1 | segment 1 | ------------------------ | | TD B TRB 1 | 1 | 1 | | ------------------------ | | TD B TRB 2 | 0 | 1 | | ------------------------ | | Link TRB | 0 | 1 |----- | ------------------------ | | | | chain cycle | | bit bit | | ------------------------ | | | TD C TRB 1 | 0 | 1 |<---- | ------------------------ | | TD D TRB 1 | 1 | 1 | | ------------------------ | | TD D TRB 2 | 1 | 1 | segment 2 | ------------------------ | | TD D TRB 3 | 1 | 1 | | ------------------------ | | TD D TRB 4 | 1 | 1 | | ------------------------ | | Link TRB | 1 | 1 |----- | ------------------------ | | | | chain cycle | | bit bit | | ------------------------ | | | TD D TRB 5 | 1 | 1 |<---- | ------------------------ | | TD D TRB 6 | 0 | 1 | | ------------------------ | | TD E TRB 1 | 0 | 1 | segment 3 | ------------------------ | | | 0 | 0 | | <-- producer enqueue ptr ------------------------ | | | 0 | 0 | | ------------------------ | | Link TRB | 0 | 0 |--------------- ------------------------ Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:34 +04:00
/**
* Debug a segment with an xHCI ring.
*
* @return The Link TRB of the segment, or NULL if there is no Link TRB
* (which is a bug, since all segments must have a Link TRB).
*
* Prints out all TRBs in the segment, even those after the Link TRB.
*
* XXX: should we print out TRBs that the HC owns? As long as we don't
* write, that should be fine... We shouldn't expect that the memory pointed to
* by the TRB is valid at all. Do we care about ones the HC owns? Probably,
* for HC debugging.
*/
void xhci_debug_segment(struct xhci_hcd *xhci, struct xhci_segment *seg)
{
int i;
u32 addr = (u32) seg->dma;
union xhci_trb *trb = seg->trbs;
for (i = 0; i < TRBS_PER_SEGMENT; ++i) {
trb = &seg->trbs[i];
xhci_dbg(xhci, "@%08x %08x %08x %08x %08x\n", addr,
USB: xhci: Represent 64-bit addresses with one u64. There are several xHCI data structures that use two 32-bit fields to represent a 64-bit address. Since some architectures don't support 64-bit PCI writes, the fields need to be written in two 32-bit writes. The xHCI specification says that if a platform is incapable of generating 64-bit writes, software must write the low 32-bits first, then the high 32-bits. Hardware that supports 64-bit addressing will wait for the high 32-bit write before reading the revised value, and hardware that only supports 32-bit writes will ignore the high 32-bit write. Previous xHCI code represented 64-bit addresses with two u32 values. This lead to buggy code that would write the 32-bits in the wrong order, or forget to write the upper 32-bits. Change the two u32s to one u64 and create a function call to write all 64-bit addresses in the proper order. This new function could be modified in the future if all platforms support 64-bit writes. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-07-27 23:03:31 +04:00
lower_32_bits(trb->link.segment_ptr),
upper_32_bits(trb->link.segment_ptr),
USB: xhci: Ring allocation and initialization. Allocate basic xHCI host controller data structures. For every xHC, there is a command ring, an event ring, and a doorbell array. The doorbell array is used to notify the host controller that work has been enqueued onto one of the rings. The host controller driver enqueues commands on the command ring. The HW enqueues command completion events on the event ring and interrupts the system (currently using PCI interrupts, although the xHCI HW will use MSI interrupts eventually). All rings and the doorbell array must be allocated by the xHCI host controller driver. Each ring is comprised of one or more segments, which consists of 16-byte Transfer Request Blocks (TRBs) that can be chained to form a Transfer Descriptor (TD) that represents a multiple-buffer request. Segments are linked into a ring using Link TRBs, which means they are dynamically growable. The producer of the ring enqueues a TD by writing one or more TRBs in the ring and toggling the TRB cycle bit for each TRB. The consumer knows it can process the TRB when the cycle bit matches its internal consumer cycle state for the ring. The consumer cycle state is toggled an odd amount of times in the ring. An example ring (a ring must have a minimum of 16 TRBs on it, but that's too big to draw in ASCII art): chain cycle bit bit ------------------------ | TD A TRB 1 | 1 | 1 |<------------- <-- consumer dequeue ptr ------------------------ | consumer cycle state = 1 | TD A TRB 2 | 1 | 1 | | ------------------------ | | TD A TRB 3 | 0 | 1 | segment 1 | ------------------------ | | TD B TRB 1 | 1 | 1 | | ------------------------ | | TD B TRB 2 | 0 | 1 | | ------------------------ | | Link TRB | 0 | 1 |----- | ------------------------ | | | | chain cycle | | bit bit | | ------------------------ | | | TD C TRB 1 | 0 | 1 |<---- | ------------------------ | | TD D TRB 1 | 1 | 1 | | ------------------------ | | TD D TRB 2 | 1 | 1 | segment 2 | ------------------------ | | TD D TRB 3 | 1 | 1 | | ------------------------ | | TD D TRB 4 | 1 | 1 | | ------------------------ | | Link TRB | 1 | 1 |----- | ------------------------ | | | | chain cycle | | bit bit | | ------------------------ | | | TD D TRB 5 | 1 | 1 |<---- | ------------------------ | | TD D TRB 6 | 0 | 1 | | ------------------------ | | TD E TRB 1 | 0 | 1 | segment 3 | ------------------------ | | | 0 | 0 | | <-- producer enqueue ptr ------------------------ | | | 0 | 0 | | ------------------------ | | Link TRB | 0 | 0 |--------------- ------------------------ Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:34 +04:00
(unsigned int) trb->link.intr_target,
(unsigned int) trb->link.control);
addr += sizeof(*trb);
}
}
USB: xhci: No-op command queueing and irq handler. xHCI host controllers can optionally implement a no-op test. This simple test ensures the OS has correctly setup all basic data structures and can correctly respond to interrupts from the host controller hardware. There are two rings exercised by the no-op test: the command ring, and the event ring. The host controller driver writes a no-op command TRB to the command ring, and rings the doorbell for the command ring (the first entry in the doorbell array). The hardware receives this event, places a command completion event on the event ring, and fires an interrupt. The host controller driver sees the interrupt, and checks the event ring for TRBs it can process, and sees the command completion event. (See the rules in xhci-ring.c for who "owns" a TRB. This is a simplified set of rules, and may not contain all the details that are in the xHCI 0.95 spec.) A timer fires every 60 seconds to debug the state of the hardware and command and event rings. This timer only runs if CONFIG_USB_XHCI_HCD_DEBUGGING is 'y'. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:53:56 +04:00
void xhci_dbg_ring_ptrs(struct xhci_hcd *xhci, struct xhci_ring *ring)
{
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "Ring deq = %p (virt), 0x%llx (dma)\n",
ring->dequeue,
USB: xhci: Avoid global namespace pollution. Make all globally visible functions start with xhci_ and mark functions as static if they're only called within the same C file. Fix some long lines while we're at it. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:05:20 +04:00
(unsigned long long)xhci_trb_virt_to_dma(ring->deq_seg,
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
ring->dequeue));
USB: xhci: No-op command queueing and irq handler. xHCI host controllers can optionally implement a no-op test. This simple test ensures the OS has correctly setup all basic data structures and can correctly respond to interrupts from the host controller hardware. There are two rings exercised by the no-op test: the command ring, and the event ring. The host controller driver writes a no-op command TRB to the command ring, and rings the doorbell for the command ring (the first entry in the doorbell array). The hardware receives this event, places a command completion event on the event ring, and fires an interrupt. The host controller driver sees the interrupt, and checks the event ring for TRBs it can process, and sees the command completion event. (See the rules in xhci-ring.c for who "owns" a TRB. This is a simplified set of rules, and may not contain all the details that are in the xHCI 0.95 spec.) A timer fires every 60 seconds to debug the state of the hardware and command and event rings. This timer only runs if CONFIG_USB_XHCI_HCD_DEBUGGING is 'y'. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:53:56 +04:00
xhci_dbg(xhci, "Ring deq updated %u times\n",
ring->deq_updates);
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "Ring enq = %p (virt), 0x%llx (dma)\n",
ring->enqueue,
USB: xhci: Avoid global namespace pollution. Make all globally visible functions start with xhci_ and mark functions as static if they're only called within the same C file. Fix some long lines while we're at it. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:05:20 +04:00
(unsigned long long)xhci_trb_virt_to_dma(ring->enq_seg,
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
ring->enqueue));
USB: xhci: No-op command queueing and irq handler. xHCI host controllers can optionally implement a no-op test. This simple test ensures the OS has correctly setup all basic data structures and can correctly respond to interrupts from the host controller hardware. There are two rings exercised by the no-op test: the command ring, and the event ring. The host controller driver writes a no-op command TRB to the command ring, and rings the doorbell for the command ring (the first entry in the doorbell array). The hardware receives this event, places a command completion event on the event ring, and fires an interrupt. The host controller driver sees the interrupt, and checks the event ring for TRBs it can process, and sees the command completion event. (See the rules in xhci-ring.c for who "owns" a TRB. This is a simplified set of rules, and may not contain all the details that are in the xHCI 0.95 spec.) A timer fires every 60 seconds to debug the state of the hardware and command and event rings. This timer only runs if CONFIG_USB_XHCI_HCD_DEBUGGING is 'y'. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:53:56 +04:00
xhci_dbg(xhci, "Ring enq updated %u times\n",
ring->enq_updates);
}
USB: xhci: Ring allocation and initialization. Allocate basic xHCI host controller data structures. For every xHC, there is a command ring, an event ring, and a doorbell array. The doorbell array is used to notify the host controller that work has been enqueued onto one of the rings. The host controller driver enqueues commands on the command ring. The HW enqueues command completion events on the event ring and interrupts the system (currently using PCI interrupts, although the xHCI HW will use MSI interrupts eventually). All rings and the doorbell array must be allocated by the xHCI host controller driver. Each ring is comprised of one or more segments, which consists of 16-byte Transfer Request Blocks (TRBs) that can be chained to form a Transfer Descriptor (TD) that represents a multiple-buffer request. Segments are linked into a ring using Link TRBs, which means they are dynamically growable. The producer of the ring enqueues a TD by writing one or more TRBs in the ring and toggling the TRB cycle bit for each TRB. The consumer knows it can process the TRB when the cycle bit matches its internal consumer cycle state for the ring. The consumer cycle state is toggled an odd amount of times in the ring. An example ring (a ring must have a minimum of 16 TRBs on it, but that's too big to draw in ASCII art): chain cycle bit bit ------------------------ | TD A TRB 1 | 1 | 1 |<------------- <-- consumer dequeue ptr ------------------------ | consumer cycle state = 1 | TD A TRB 2 | 1 | 1 | | ------------------------ | | TD A TRB 3 | 0 | 1 | segment 1 | ------------------------ | | TD B TRB 1 | 1 | 1 | | ------------------------ | | TD B TRB 2 | 0 | 1 | | ------------------------ | | Link TRB | 0 | 1 |----- | ------------------------ | | | | chain cycle | | bit bit | | ------------------------ | | | TD C TRB 1 | 0 | 1 |<---- | ------------------------ | | TD D TRB 1 | 1 | 1 | | ------------------------ | | TD D TRB 2 | 1 | 1 | segment 2 | ------------------------ | | TD D TRB 3 | 1 | 1 | | ------------------------ | | TD D TRB 4 | 1 | 1 | | ------------------------ | | Link TRB | 1 | 1 |----- | ------------------------ | | | | chain cycle | | bit bit | | ------------------------ | | | TD D TRB 5 | 1 | 1 |<---- | ------------------------ | | TD D TRB 6 | 0 | 1 | | ------------------------ | | TD E TRB 1 | 0 | 1 | segment 3 | ------------------------ | | | 0 | 0 | | <-- producer enqueue ptr ------------------------ | | | 0 | 0 | | ------------------------ | | Link TRB | 0 | 0 |--------------- ------------------------ Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:34 +04:00
/**
* Debugging for an xHCI ring, which is a queue broken into multiple segments.
*
* Print out each segment in the ring. Check that the DMA address in
* each link segment actually matches the segment's stored DMA address.
* Check that the link end bit is only set at the end of the ring.
* Check that the dequeue and enqueue pointers point to real data in this ring
* (not some other ring).
*/
void xhci_debug_ring(struct xhci_hcd *xhci, struct xhci_ring *ring)
{
/* FIXME: Throw an error if any segment doesn't have a Link TRB */
struct xhci_segment *seg;
struct xhci_segment *first_seg = ring->first_seg;
xhci_debug_segment(xhci, first_seg);
USB: xhci: No-op command queueing and irq handler. xHCI host controllers can optionally implement a no-op test. This simple test ensures the OS has correctly setup all basic data structures and can correctly respond to interrupts from the host controller hardware. There are two rings exercised by the no-op test: the command ring, and the event ring. The host controller driver writes a no-op command TRB to the command ring, and rings the doorbell for the command ring (the first entry in the doorbell array). The hardware receives this event, places a command completion event on the event ring, and fires an interrupt. The host controller driver sees the interrupt, and checks the event ring for TRBs it can process, and sees the command completion event. (See the rules in xhci-ring.c for who "owns" a TRB. This is a simplified set of rules, and may not contain all the details that are in the xHCI 0.95 spec.) A timer fires every 60 seconds to debug the state of the hardware and command and event rings. This timer only runs if CONFIG_USB_XHCI_HCD_DEBUGGING is 'y'. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:53:56 +04:00
if (!ring->enq_updates && !ring->deq_updates) {
xhci_dbg(xhci, " Ring has not been updated\n");
return;
}
USB: xhci: Ring allocation and initialization. Allocate basic xHCI host controller data structures. For every xHC, there is a command ring, an event ring, and a doorbell array. The doorbell array is used to notify the host controller that work has been enqueued onto one of the rings. The host controller driver enqueues commands on the command ring. The HW enqueues command completion events on the event ring and interrupts the system (currently using PCI interrupts, although the xHCI HW will use MSI interrupts eventually). All rings and the doorbell array must be allocated by the xHCI host controller driver. Each ring is comprised of one or more segments, which consists of 16-byte Transfer Request Blocks (TRBs) that can be chained to form a Transfer Descriptor (TD) that represents a multiple-buffer request. Segments are linked into a ring using Link TRBs, which means they are dynamically growable. The producer of the ring enqueues a TD by writing one or more TRBs in the ring and toggling the TRB cycle bit for each TRB. The consumer knows it can process the TRB when the cycle bit matches its internal consumer cycle state for the ring. The consumer cycle state is toggled an odd amount of times in the ring. An example ring (a ring must have a minimum of 16 TRBs on it, but that's too big to draw in ASCII art): chain cycle bit bit ------------------------ | TD A TRB 1 | 1 | 1 |<------------- <-- consumer dequeue ptr ------------------------ | consumer cycle state = 1 | TD A TRB 2 | 1 | 1 | | ------------------------ | | TD A TRB 3 | 0 | 1 | segment 1 | ------------------------ | | TD B TRB 1 | 1 | 1 | | ------------------------ | | TD B TRB 2 | 0 | 1 | | ------------------------ | | Link TRB | 0 | 1 |----- | ------------------------ | | | | chain cycle | | bit bit | | ------------------------ | | | TD C TRB 1 | 0 | 1 |<---- | ------------------------ | | TD D TRB 1 | 1 | 1 | | ------------------------ | | TD D TRB 2 | 1 | 1 | segment 2 | ------------------------ | | TD D TRB 3 | 1 | 1 | | ------------------------ | | TD D TRB 4 | 1 | 1 | | ------------------------ | | Link TRB | 1 | 1 |----- | ------------------------ | | | | chain cycle | | bit bit | | ------------------------ | | | TD D TRB 5 | 1 | 1 |<---- | ------------------------ | | TD D TRB 6 | 0 | 1 | | ------------------------ | | TD E TRB 1 | 0 | 1 | segment 3 | ------------------------ | | | 0 | 0 | | <-- producer enqueue ptr ------------------------ | | | 0 | 0 | | ------------------------ | | Link TRB | 0 | 0 |--------------- ------------------------ Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:34 +04:00
for (seg = first_seg->next; seg != first_seg; seg = seg->next)
xhci_debug_segment(xhci, seg);
}
void xhci_dbg_erst(struct xhci_hcd *xhci, struct xhci_erst *erst)
{
u32 addr = (u32) erst->erst_dma_addr;
int i;
struct xhci_erst_entry *entry;
for (i = 0; i < erst->num_entries; ++i) {
entry = &erst->entries[i];
xhci_dbg(xhci, "@%08x %08x %08x %08x %08x\n",
(unsigned int) addr,
USB: xhci: Represent 64-bit addresses with one u64. There are several xHCI data structures that use two 32-bit fields to represent a 64-bit address. Since some architectures don't support 64-bit PCI writes, the fields need to be written in two 32-bit writes. The xHCI specification says that if a platform is incapable of generating 64-bit writes, software must write the low 32-bits first, then the high 32-bits. Hardware that supports 64-bit addressing will wait for the high 32-bit write before reading the revised value, and hardware that only supports 32-bit writes will ignore the high 32-bit write. Previous xHCI code represented 64-bit addresses with two u32 values. This lead to buggy code that would write the 32-bits in the wrong order, or forget to write the upper 32-bits. Change the two u32s to one u64 and create a function call to write all 64-bit addresses in the proper order. This new function could be modified in the future if all platforms support 64-bit writes. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-07-27 23:03:31 +04:00
lower_32_bits(entry->seg_addr),
upper_32_bits(entry->seg_addr),
USB: xhci: Ring allocation and initialization. Allocate basic xHCI host controller data structures. For every xHC, there is a command ring, an event ring, and a doorbell array. The doorbell array is used to notify the host controller that work has been enqueued onto one of the rings. The host controller driver enqueues commands on the command ring. The HW enqueues command completion events on the event ring and interrupts the system (currently using PCI interrupts, although the xHCI HW will use MSI interrupts eventually). All rings and the doorbell array must be allocated by the xHCI host controller driver. Each ring is comprised of one or more segments, which consists of 16-byte Transfer Request Blocks (TRBs) that can be chained to form a Transfer Descriptor (TD) that represents a multiple-buffer request. Segments are linked into a ring using Link TRBs, which means they are dynamically growable. The producer of the ring enqueues a TD by writing one or more TRBs in the ring and toggling the TRB cycle bit for each TRB. The consumer knows it can process the TRB when the cycle bit matches its internal consumer cycle state for the ring. The consumer cycle state is toggled an odd amount of times in the ring. An example ring (a ring must have a minimum of 16 TRBs on it, but that's too big to draw in ASCII art): chain cycle bit bit ------------------------ | TD A TRB 1 | 1 | 1 |<------------- <-- consumer dequeue ptr ------------------------ | consumer cycle state = 1 | TD A TRB 2 | 1 | 1 | | ------------------------ | | TD A TRB 3 | 0 | 1 | segment 1 | ------------------------ | | TD B TRB 1 | 1 | 1 | | ------------------------ | | TD B TRB 2 | 0 | 1 | | ------------------------ | | Link TRB | 0 | 1 |----- | ------------------------ | | | | chain cycle | | bit bit | | ------------------------ | | | TD C TRB 1 | 0 | 1 |<---- | ------------------------ | | TD D TRB 1 | 1 | 1 | | ------------------------ | | TD D TRB 2 | 1 | 1 | segment 2 | ------------------------ | | TD D TRB 3 | 1 | 1 | | ------------------------ | | TD D TRB 4 | 1 | 1 | | ------------------------ | | Link TRB | 1 | 1 |----- | ------------------------ | | | | chain cycle | | bit bit | | ------------------------ | | | TD D TRB 5 | 1 | 1 |<---- | ------------------------ | | TD D TRB 6 | 0 | 1 | | ------------------------ | | TD E TRB 1 | 0 | 1 | segment 3 | ------------------------ | | | 0 | 0 | | <-- producer enqueue ptr ------------------------ | | | 0 | 0 | | ------------------------ | | Link TRB | 0 | 0 |--------------- ------------------------ Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:34 +04:00
(unsigned int) entry->seg_size,
(unsigned int) entry->rsvd);
addr += sizeof(*entry);
}
}
void xhci_dbg_cmd_ptrs(struct xhci_hcd *xhci)
{
USB: xhci: Represent 64-bit addresses with one u64. There are several xHCI data structures that use two 32-bit fields to represent a 64-bit address. Since some architectures don't support 64-bit PCI writes, the fields need to be written in two 32-bit writes. The xHCI specification says that if a platform is incapable of generating 64-bit writes, software must write the low 32-bits first, then the high 32-bits. Hardware that supports 64-bit addressing will wait for the high 32-bit write before reading the revised value, and hardware that only supports 32-bit writes will ignore the high 32-bit write. Previous xHCI code represented 64-bit addresses with two u32 values. This lead to buggy code that would write the 32-bits in the wrong order, or forget to write the upper 32-bits. Change the two u32s to one u64 and create a function call to write all 64-bit addresses in the proper order. This new function could be modified in the future if all platforms support 64-bit writes. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-07-27 23:03:31 +04:00
u64 val;
USB: xhci: Ring allocation and initialization. Allocate basic xHCI host controller data structures. For every xHC, there is a command ring, an event ring, and a doorbell array. The doorbell array is used to notify the host controller that work has been enqueued onto one of the rings. The host controller driver enqueues commands on the command ring. The HW enqueues command completion events on the event ring and interrupts the system (currently using PCI interrupts, although the xHCI HW will use MSI interrupts eventually). All rings and the doorbell array must be allocated by the xHCI host controller driver. Each ring is comprised of one or more segments, which consists of 16-byte Transfer Request Blocks (TRBs) that can be chained to form a Transfer Descriptor (TD) that represents a multiple-buffer request. Segments are linked into a ring using Link TRBs, which means they are dynamically growable. The producer of the ring enqueues a TD by writing one or more TRBs in the ring and toggling the TRB cycle bit for each TRB. The consumer knows it can process the TRB when the cycle bit matches its internal consumer cycle state for the ring. The consumer cycle state is toggled an odd amount of times in the ring. An example ring (a ring must have a minimum of 16 TRBs on it, but that's too big to draw in ASCII art): chain cycle bit bit ------------------------ | TD A TRB 1 | 1 | 1 |<------------- <-- consumer dequeue ptr ------------------------ | consumer cycle state = 1 | TD A TRB 2 | 1 | 1 | | ------------------------ | | TD A TRB 3 | 0 | 1 | segment 1 | ------------------------ | | TD B TRB 1 | 1 | 1 | | ------------------------ | | TD B TRB 2 | 0 | 1 | | ------------------------ | | Link TRB | 0 | 1 |----- | ------------------------ | | | | chain cycle | | bit bit | | ------------------------ | | | TD C TRB 1 | 0 | 1 |<---- | ------------------------ | | TD D TRB 1 | 1 | 1 | | ------------------------ | | TD D TRB 2 | 1 | 1 | segment 2 | ------------------------ | | TD D TRB 3 | 1 | 1 | | ------------------------ | | TD D TRB 4 | 1 | 1 | | ------------------------ | | Link TRB | 1 | 1 |----- | ------------------------ | | | | chain cycle | | bit bit | | ------------------------ | | | TD D TRB 5 | 1 | 1 |<---- | ------------------------ | | TD D TRB 6 | 0 | 1 | | ------------------------ | | TD E TRB 1 | 0 | 1 | segment 3 | ------------------------ | | | 0 | 0 | | <-- producer enqueue ptr ------------------------ | | | 0 | 0 | | ------------------------ | | Link TRB | 0 | 0 |--------------- ------------------------ Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:34 +04:00
USB: xhci: Represent 64-bit addresses with one u64. There are several xHCI data structures that use two 32-bit fields to represent a 64-bit address. Since some architectures don't support 64-bit PCI writes, the fields need to be written in two 32-bit writes. The xHCI specification says that if a platform is incapable of generating 64-bit writes, software must write the low 32-bits first, then the high 32-bits. Hardware that supports 64-bit addressing will wait for the high 32-bit write before reading the revised value, and hardware that only supports 32-bit writes will ignore the high 32-bit write. Previous xHCI code represented 64-bit addresses with two u32 values. This lead to buggy code that would write the 32-bits in the wrong order, or forget to write the upper 32-bits. Change the two u32s to one u64 and create a function call to write all 64-bit addresses in the proper order. This new function could be modified in the future if all platforms support 64-bit writes. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-07-27 23:03:31 +04:00
val = xhci_read_64(xhci, &xhci->op_regs->cmd_ring);
xhci_dbg(xhci, "// xHC command ring deq ptr low bits + flags = @%08x\n",
lower_32_bits(val));
xhci_dbg(xhci, "// xHC command ring deq ptr high bits = @%08x\n",
upper_32_bits(val));
USB: xhci: Ring allocation and initialization. Allocate basic xHCI host controller data structures. For every xHC, there is a command ring, an event ring, and a doorbell array. The doorbell array is used to notify the host controller that work has been enqueued onto one of the rings. The host controller driver enqueues commands on the command ring. The HW enqueues command completion events on the event ring and interrupts the system (currently using PCI interrupts, although the xHCI HW will use MSI interrupts eventually). All rings and the doorbell array must be allocated by the xHCI host controller driver. Each ring is comprised of one or more segments, which consists of 16-byte Transfer Request Blocks (TRBs) that can be chained to form a Transfer Descriptor (TD) that represents a multiple-buffer request. Segments are linked into a ring using Link TRBs, which means they are dynamically growable. The producer of the ring enqueues a TD by writing one or more TRBs in the ring and toggling the TRB cycle bit for each TRB. The consumer knows it can process the TRB when the cycle bit matches its internal consumer cycle state for the ring. The consumer cycle state is toggled an odd amount of times in the ring. An example ring (a ring must have a minimum of 16 TRBs on it, but that's too big to draw in ASCII art): chain cycle bit bit ------------------------ | TD A TRB 1 | 1 | 1 |<------------- <-- consumer dequeue ptr ------------------------ | consumer cycle state = 1 | TD A TRB 2 | 1 | 1 | | ------------------------ | | TD A TRB 3 | 0 | 1 | segment 1 | ------------------------ | | TD B TRB 1 | 1 | 1 | | ------------------------ | | TD B TRB 2 | 0 | 1 | | ------------------------ | | Link TRB | 0 | 1 |----- | ------------------------ | | | | chain cycle | | bit bit | | ------------------------ | | | TD C TRB 1 | 0 | 1 |<---- | ------------------------ | | TD D TRB 1 | 1 | 1 | | ------------------------ | | TD D TRB 2 | 1 | 1 | segment 2 | ------------------------ | | TD D TRB 3 | 1 | 1 | | ------------------------ | | TD D TRB 4 | 1 | 1 | | ------------------------ | | Link TRB | 1 | 1 |----- | ------------------------ | | | | chain cycle | | bit bit | | ------------------------ | | | TD D TRB 5 | 1 | 1 |<---- | ------------------------ | | TD D TRB 6 | 0 | 1 | | ------------------------ | | TD E TRB 1 | 0 | 1 | segment 3 | ------------------------ | | | 0 | 0 | | <-- producer enqueue ptr ------------------------ | | | 0 | 0 | | ------------------------ | | Link TRB | 0 | 0 |--------------- ------------------------ Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:52:34 +04:00
}
USB: xhci: Allocate and address USB devices xHCI needs to get a "Slot ID" from the host controller and allocate other data structures for every USB device. Make usb_alloc_dev() and usb_release_dev() allocate and free these device structures. After setting up the xHC device structures, usb_alloc_dev() must wait for the hardware to respond to an Enable Slot command. usb_alloc_dev() fires off a Disable Slot command and does not wait for it to complete. When the USB core wants to choose an address for the device, the xHCI driver must issue a Set Address command and wait for an event for that command. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:57:38 +04:00
void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep)
{
int i, j;
int last_ep_ctx = 31;
/* Fields are 32 bits wide, DMA addresses are in bytes */
int field_size = 32 / 8;
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - drop flags\n",
&ctx->drop_flags, (unsigned long long)dma,
ctx->drop_flags);
USB: xhci: Allocate and address USB devices xHCI needs to get a "Slot ID" from the host controller and allocate other data structures for every USB device. Make usb_alloc_dev() and usb_release_dev() allocate and free these device structures. After setting up the xHC device structures, usb_alloc_dev() must wait for the hardware to respond to an Enable Slot command. usb_alloc_dev() fires off a Disable Slot command and does not wait for it to complete. When the USB core wants to choose an address for the device, the xHCI driver must issue a Set Address command and wait for an event for that command. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:57:38 +04:00
dma += field_size;
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - add flags\n",
&ctx->add_flags, (unsigned long long)dma,
ctx->add_flags);
USB: xhci: Allocate and address USB devices xHCI needs to get a "Slot ID" from the host controller and allocate other data structures for every USB device. Make usb_alloc_dev() and usb_release_dev() allocate and free these device structures. After setting up the xHC device structures, usb_alloc_dev() must wait for the hardware to respond to an Enable Slot command. usb_alloc_dev() fires off a Disable Slot command and does not wait for it to complete. When the USB core wants to choose an address for the device, the xHCI driver must issue a Set Address command and wait for an event for that command. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:57:38 +04:00
dma += field_size;
USB: xhci: fix less- and greater than confusion Without this change the loops won't start Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-07-13 02:23:47 +04:00
for (i = 0; i < 6; ++i) {
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n",
&ctx->rsvd[i], (unsigned long long)dma,
ctx->rsvd[i], i);
USB: xhci: Allocate and address USB devices xHCI needs to get a "Slot ID" from the host controller and allocate other data structures for every USB device. Make usb_alloc_dev() and usb_release_dev() allocate and free these device structures. After setting up the xHC device structures, usb_alloc_dev() must wait for the hardware to respond to an Enable Slot command. usb_alloc_dev() fires off a Disable Slot command and does not wait for it to complete. When the USB core wants to choose an address for the device, the xHCI driver must issue a Set Address command and wait for an event for that command. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:57:38 +04:00
dma += field_size;
}
xhci_dbg(xhci, "Slot Context:\n");
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_info\n",
&ctx->slot.dev_info,
(unsigned long long)dma, ctx->slot.dev_info);
USB: xhci: Allocate and address USB devices xHCI needs to get a "Slot ID" from the host controller and allocate other data structures for every USB device. Make usb_alloc_dev() and usb_release_dev() allocate and free these device structures. After setting up the xHC device structures, usb_alloc_dev() must wait for the hardware to respond to an Enable Slot command. usb_alloc_dev() fires off a Disable Slot command and does not wait for it to complete. When the USB core wants to choose an address for the device, the xHCI driver must issue a Set Address command and wait for an event for that command. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:57:38 +04:00
dma += field_size;
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_info2\n",
&ctx->slot.dev_info2,
(unsigned long long)dma, ctx->slot.dev_info2);
USB: xhci: Allocate and address USB devices xHCI needs to get a "Slot ID" from the host controller and allocate other data structures for every USB device. Make usb_alloc_dev() and usb_release_dev() allocate and free these device structures. After setting up the xHC device structures, usb_alloc_dev() must wait for the hardware to respond to an Enable Slot command. usb_alloc_dev() fires off a Disable Slot command and does not wait for it to complete. When the USB core wants to choose an address for the device, the xHCI driver must issue a Set Address command and wait for an event for that command. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:57:38 +04:00
dma += field_size;
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - tt_info\n",
&ctx->slot.tt_info,
(unsigned long long)dma, ctx->slot.tt_info);
USB: xhci: Allocate and address USB devices xHCI needs to get a "Slot ID" from the host controller and allocate other data structures for every USB device. Make usb_alloc_dev() and usb_release_dev() allocate and free these device structures. After setting up the xHC device structures, usb_alloc_dev() must wait for the hardware to respond to an Enable Slot command. usb_alloc_dev() fires off a Disable Slot command and does not wait for it to complete. When the USB core wants to choose an address for the device, the xHCI driver must issue a Set Address command and wait for an event for that command. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:57:38 +04:00
dma += field_size;
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_state\n",
&ctx->slot.dev_state,
(unsigned long long)dma, ctx->slot.dev_state);
USB: xhci: Allocate and address USB devices xHCI needs to get a "Slot ID" from the host controller and allocate other data structures for every USB device. Make usb_alloc_dev() and usb_release_dev() allocate and free these device structures. After setting up the xHC device structures, usb_alloc_dev() must wait for the hardware to respond to an Enable Slot command. usb_alloc_dev() fires off a Disable Slot command and does not wait for it to complete. When the USB core wants to choose an address for the device, the xHCI driver must issue a Set Address command and wait for an event for that command. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:57:38 +04:00
dma += field_size;
USB: xhci: fix less- and greater than confusion Without this change the loops won't start Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-07-13 02:23:47 +04:00
for (i = 0; i < 4; ++i) {
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n",
&ctx->slot.reserved[i], (unsigned long long)dma,
ctx->slot.reserved[i], i);
USB: xhci: Allocate and address USB devices xHCI needs to get a "Slot ID" from the host controller and allocate other data structures for every USB device. Make usb_alloc_dev() and usb_release_dev() allocate and free these device structures. After setting up the xHC device structures, usb_alloc_dev() must wait for the hardware to respond to an Enable Slot command. usb_alloc_dev() fires off a Disable Slot command and does not wait for it to complete. When the USB core wants to choose an address for the device, the xHCI driver must issue a Set Address command and wait for an event for that command. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:57:38 +04:00
dma += field_size;
}
if (last_ep < 31)
last_ep_ctx = last_ep + 1;
for (i = 0; i < last_ep_ctx; ++i) {
xhci_dbg(xhci, "Endpoint %02d Context:\n", i);
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - ep_info\n",
&ctx->ep[i].ep_info,
(unsigned long long)dma, ctx->ep[i].ep_info);
USB: xhci: Allocate and address USB devices xHCI needs to get a "Slot ID" from the host controller and allocate other data structures for every USB device. Make usb_alloc_dev() and usb_release_dev() allocate and free these device structures. After setting up the xHC device structures, usb_alloc_dev() must wait for the hardware to respond to an Enable Slot command. usb_alloc_dev() fires off a Disable Slot command and does not wait for it to complete. When the USB core wants to choose an address for the device, the xHCI driver must issue a Set Address command and wait for an event for that command. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:57:38 +04:00
dma += field_size;
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - ep_info2\n",
&ctx->ep[i].ep_info2,
(unsigned long long)dma, ctx->ep[i].ep_info2);
USB: xhci: Allocate and address USB devices xHCI needs to get a "Slot ID" from the host controller and allocate other data structures for every USB device. Make usb_alloc_dev() and usb_release_dev() allocate and free these device structures. After setting up the xHC device structures, usb_alloc_dev() must wait for the hardware to respond to an Enable Slot command. usb_alloc_dev() fires off a Disable Slot command and does not wait for it to complete. When the USB core wants to choose an address for the device, the xHCI driver must issue a Set Address command and wait for an event for that command. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:57:38 +04:00
dma += field_size;
USB: xhci: Represent 64-bit addresses with one u64. There are several xHCI data structures that use two 32-bit fields to represent a 64-bit address. Since some architectures don't support 64-bit PCI writes, the fields need to be written in two 32-bit writes. The xHCI specification says that if a platform is incapable of generating 64-bit writes, software must write the low 32-bits first, then the high 32-bits. Hardware that supports 64-bit addressing will wait for the high 32-bit write before reading the revised value, and hardware that only supports 32-bit writes will ignore the high 32-bit write. Previous xHCI code represented 64-bit addresses with two u32 values. This lead to buggy code that would write the 32-bits in the wrong order, or forget to write the upper 32-bits. Change the two u32s to one u64 and create a function call to write all 64-bit addresses in the proper order. This new function could be modified in the future if all platforms support 64-bit writes. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-07-27 23:03:31 +04:00
xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08llx - deq\n",
&ctx->ep[i].deq,
(unsigned long long)dma, ctx->ep[i].deq);
dma += 2*field_size;
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - tx_info\n",
&ctx->ep[i].tx_info,
(unsigned long long)dma, ctx->ep[i].tx_info);
USB: xhci: Allocate and address USB devices xHCI needs to get a "Slot ID" from the host controller and allocate other data structures for every USB device. Make usb_alloc_dev() and usb_release_dev() allocate and free these device structures. After setting up the xHC device structures, usb_alloc_dev() must wait for the hardware to respond to an Enable Slot command. usb_alloc_dev() fires off a Disable Slot command and does not wait for it to complete. When the USB core wants to choose an address for the device, the xHCI driver must issue a Set Address command and wait for an event for that command. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:57:38 +04:00
dma += field_size;
for (j = 0; j < 3; ++j) {
USB: xhci: fix lots of compiler warnings. Turns out someone never built this code on a 64bit platform. Someone owes me a beer... Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 06:14:08 +04:00
xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n",
&ctx->ep[i].reserved[j],
(unsigned long long)dma,
ctx->ep[i].reserved[j], j);
USB: xhci: Allocate and address USB devices xHCI needs to get a "Slot ID" from the host controller and allocate other data structures for every USB device. Make usb_alloc_dev() and usb_release_dev() allocate and free these device structures. After setting up the xHC device structures, usb_alloc_dev() must wait for the hardware to respond to an Enable Slot command. usb_alloc_dev() fires off a Disable Slot command and does not wait for it to complete. When the USB core wants to choose an address for the device, the xHCI driver must issue a Set Address command and wait for an event for that command. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 06:57:38 +04:00
dma += field_size;
}
}
}
Reference in New Issue Copy Permalink