2019-06-03 07:44:50 +02:00
/* SPDX-License-Identifier: GPL-2.0-only */
2012-03-05 11:49:33 +00:00
/*
* Copyright ( C ) 2012 ARM Ltd .
*/
# ifndef __ASM_MODULE_H
# define __ASM_MODULE_H
# include <asm-generic/module.h>
arm64: module: split core and init PLT sections
The arm64 module PLT code allocates all PLT entries in a single core
section, since the overhead of having a separate init PLT section is
not justified by the small number of PLT entries usually required for
init code.
However, the core and init module regions are allocated independently,
and there is a corner case where the core region may be allocated from
the VMALLOC region if the dedicated module region is exhausted, but the
init region, being much smaller, can still be allocated from the module
region. This leads to relocation failures if the distance between those
regions exceeds 128 MB. (In fact, this corner case is highly unlikely to
occur on arm64, but the issue has been observed on ARM, whose module
region is much smaller).
So split the core and init PLT regions, and name the latter ".init.plt"
so it gets allocated along with (and sufficiently close to) the .init
sections that it serves. Also, given that init PLT entries may need to
be emitted for branches that target the core module, modify the logic
that disregards defined symbols to only disregard symbols that are
defined in the same section as the relocated branch instruction.
Since there may now be two PLT entries associated with each entry in
the symbol table, we can no longer hijack the symbol::st_size fields
to record the addresses of PLT entries as we emit them for zero-addend
relocations. So instead, perform an explicit comparison to check for
duplicate entries.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2017-02-21 22:12:57 +00:00
struct mod_plt_sec {
2018-11-05 19:53:23 +01:00
int plt_shndx ;
2015-11-24 12:37:35 +01:00
int plt_num_entries ;
int plt_max_entries ;
} ;
arm64: module: split core and init PLT sections
The arm64 module PLT code allocates all PLT entries in a single core
section, since the overhead of having a separate init PLT section is
not justified by the small number of PLT entries usually required for
init code.
However, the core and init module regions are allocated independently,
and there is a corner case where the core region may be allocated from
the VMALLOC region if the dedicated module region is exhausted, but the
init region, being much smaller, can still be allocated from the module
region. This leads to relocation failures if the distance between those
regions exceeds 128 MB. (In fact, this corner case is highly unlikely to
occur on arm64, but the issue has been observed on ARM, whose module
region is much smaller).
So split the core and init PLT regions, and name the latter ".init.plt"
so it gets allocated along with (and sufficiently close to) the .init
sections that it serves. Also, given that init PLT entries may need to
be emitted for branches that target the core module, modify the logic
that disregards defined symbols to only disregard symbols that are
defined in the same section as the relocated branch instruction.
Since there may now be two PLT entries associated with each entry in
the symbol table, we can no longer hijack the symbol::st_size fields
to record the addresses of PLT entries as we emit them for zero-addend
relocations. So instead, perform an explicit comparison to check for
duplicate entries.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2017-02-21 22:12:57 +00:00
struct mod_arch_specific {
struct mod_plt_sec core ;
struct mod_plt_sec init ;
2017-06-06 17:00:22 +00:00
/* for CONFIG_DYNAMIC_FTRACE */
arm64: implement ftrace with regs
This patch implements FTRACE_WITH_REGS for arm64, which allows a traced
function's arguments (and some other registers) to be captured into a
struct pt_regs, allowing these to be inspected and/or modified. This is
a building block for live-patching, where a function's arguments may be
forwarded to another function. This is also necessary to enable ftrace
and in-kernel pointer authentication at the same time, as it allows the
LR value to be captured and adjusted prior to signing.
Using GCC's -fpatchable-function-entry=N option, we can have the
compiler insert a configurable number of NOPs between the function entry
point and the usual prologue. This also ensures functions are AAPCS
compliant (e.g. disabling inter-procedural register allocation).
For example, with -fpatchable-function-entry=2, GCC 8.1.0 compiles the
following:
| unsigned long bar(void);
|
| unsigned long foo(void)
| {
| return bar() + 1;
| }
... to:
| <foo>:
| nop
| nop
| stp x29, x30, [sp, #-16]!
| mov x29, sp
| bl 0 <bar>
| add x0, x0, #0x1
| ldp x29, x30, [sp], #16
| ret
This patch builds the kernel with -fpatchable-function-entry=2,
prefixing each function with two NOPs. To trace a function, we replace
these NOPs with a sequence that saves the LR into a GPR, then calls an
ftrace entry assembly function which saves this and other relevant
registers:
| mov x9, x30
| bl <ftrace-entry>
Since patchable functions are AAPCS compliant (and the kernel does not
use x18 as a platform register), x9-x18 can be safely clobbered in the
patched sequence and the ftrace entry code.
There are now two ftrace entry functions, ftrace_regs_entry (which saves
all GPRs), and ftrace_entry (which saves the bare minimum). A PLT is
allocated for each within modules.
Signed-off-by: Torsten Duwe <duwe@suse.de>
[Mark: rework asm, comments, PLTs, initialization, commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Tested-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Tested-by: Torsten Duwe <duwe@suse.de>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Julien Thierry <jthierry@redhat.com>
Cc: Will Deacon <will@kernel.org>
2019-02-08 16:10:19 +01:00
struct plt_entry * ftrace_trampolines ;
arm64: module: split core and init PLT sections
The arm64 module PLT code allocates all PLT entries in a single core
section, since the overhead of having a separate init PLT section is
not justified by the small number of PLT entries usually required for
init code.
However, the core and init module regions are allocated independently,
and there is a corner case where the core region may be allocated from
the VMALLOC region if the dedicated module region is exhausted, but the
init region, being much smaller, can still be allocated from the module
region. This leads to relocation failures if the distance between those
regions exceeds 128 MB. (In fact, this corner case is highly unlikely to
occur on arm64, but the issue has been observed on ARM, whose module
region is much smaller).
So split the core and init PLT regions, and name the latter ".init.plt"
so it gets allocated along with (and sufficiently close to) the .init
sections that it serves. Also, given that init PLT entries may need to
be emitted for branches that target the core module, modify the logic
that disregards defined symbols to only disregard symbols that are
defined in the same section as the relocated branch instruction.
Since there may now be two PLT entries associated with each entry in
the symbol table, we can no longer hijack the symbol::st_size fields
to record the addresses of PLT entries as we emit them for zero-addend
relocations. So instead, perform an explicit comparison to check for
duplicate entries.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2017-02-21 22:12:57 +00:00
} ;
2015-11-24 12:37:35 +01:00
2018-11-05 19:53:23 +01:00
u64 module_emit_plt_entry ( struct module * mod , Elf64_Shdr * sechdrs ,
void * loc , const Elf64_Rela * rela ,
2015-11-24 12:37:35 +01:00
Elf64_Sym * sym ) ;
2018-11-05 19:53:23 +01:00
u64 module_emit_veneer_for_adrp ( struct module * mod , Elf64_Shdr * sechdrs ,
void * loc , u64 val ) ;
arm64/kernel: don't ban ADRP to work around Cortex-A53 erratum #843419
Working around Cortex-A53 erratum #843419 involves special handling of
ADRP instructions that end up in the last two instruction slots of a
4k page, or whose output register gets overwritten without having been
read. (Note that the latter instruction sequence is never emitted by
a properly functioning compiler, which is why it is disregarded by the
handling of the same erratum in the bfd.ld linker which we rely on for
the core kernel)
Normally, this gets taken care of by the linker, which can spot such
sequences at final link time, and insert a veneer if the ADRP ends up
at a vulnerable offset. However, linux kernel modules are partially
linked ELF objects, and so there is no 'final link time' other than the
runtime loading of the module, at which time all the static relocations
are resolved.
For this reason, we have implemented the #843419 workaround for modules
by avoiding ADRP instructions altogether, by using the large C model,
and by passing -mpc-relative-literal-loads to recent versions of GCC
that may emit adrp/ldr pairs to perform literal loads. However, this
workaround forces us to keep literal data mixed with the instructions
in the executable .text segment, and literal data may inadvertently
turn into an exploitable speculative gadget depending on the relative
offsets of arbitrary symbols.
So let's reimplement this workaround in a way that allows us to switch
back to the small C model, and to drop the -mpc-relative-literal-loads
GCC switch, by patching affected ADRP instructions at runtime:
- ADRP instructions that do not appear at 4k relative offset 0xff8 or
0xffc are ignored
- ADRP instructions that are within 1 MB of their target symbol are
converted into ADR instructions
- remaining ADRP instructions are redirected via a veneer that performs
the load using an unaffected movn/movk sequence.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: tidied up ADRP -> ADR instruction patching.]
[will: use ULL suffix for 64-bit immediate]
Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-03-06 17:15:33 +00:00
2017-11-20 17:41:29 +00:00
struct plt_entry {
/*
* A program that conforms to the AArch64 Procedure Call Standard
* ( AAPCS64 ) must assume that a veneer that alters IP0 ( x16 ) and / or
* IP1 ( x17 ) may be inserted at any branch instruction that is
* exposed to a relocation that supports long branches . Since that
* is exactly what we are dealing with here , we are free to use x16
* as a scratch register in the PLT veneers .
*/
2018-11-22 09:46:46 +01:00
__le32 adrp ; /* adrp x16, .... */
__le32 add ; /* add x16, x16, #0x.... */
2017-11-20 17:41:29 +00:00
__le32 br ; /* br x16 */
} ;
2018-11-22 09:46:46 +01:00
static inline bool is_forbidden_offset_for_adrp ( void * place )
2017-11-20 17:41:29 +00:00
{
arm64: Avoid cpus_have_const_cap() for ARM64_WORKAROUND_843419
In count_plts() and is_forbidden_offset_for_adrp() we use
cpus_have_const_cap() to check for ARM64_WORKAROUND_843419, but this is
not necessary and cpus_have_final_cap() would be preferable.
For historical reasons, cpus_have_const_cap() is more complicated than
it needs to be. Before cpucaps are finalized, it will perform a bitmap
test of the system_cpucaps bitmap, and once cpucaps are finalized it
will use an alternative branch. This used to be necessary to handle some
race conditions in the window between cpucap detection and the
subsequent patching of alternatives and static branches, where different
branches could be out-of-sync with one another (or w.r.t. alternative
sequences). Now that we use alternative branches instead of static
branches, these are all patched atomically w.r.t. one another, and there
are only a handful of cases that need special care in the window between
cpucap detection and alternative patching.
Due to the above, it would be nice to remove cpus_have_const_cap(), and
migrate callers over to alternative_has_cap_*(), cpus_have_final_cap(),
or cpus_have_cap() depending on when their requirements. This will
remove redundant instructions and improve code generation, and will make
it easier to determine how each callsite will behave before, during, and
after alternative patching.
It's not possible to load a module in the window between detecting the
ARM64_WORKAROUND_843419 cpucap and patching alternatives. The module VA
range limits are initialized much later in module_init_limits() which is
a subsys_initcall, and module loading cannot happen before this. Hence
it's not necessary for count_plts() or is_forbidden_offset_for_adrp() to
use cpus_have_const_cap().
This patch replaces the use of cpus_have_const_cap() with
cpus_have_final_cap() which will avoid generating code to test the
system_cpucaps bitmap and should be better for all subsequent calls at
runtime. Using cpus_have_final_cap() clearly documents that we do not
expect this code to run before cpucaps are finalized, and will make it
easier to spot issues if code is changed in future to allow modules to
be loaded earlier. The ARM64_WORKAROUND_843419 cpucap is added to
cpucap_is_possible() so that code can be elided entirely when this is not
possible, and redundant IS_ENABLED() checks are removed.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
2023-10-16 11:24:54 +01:00
return cpus_have_final_cap ( ARM64_WORKAROUND_843419 ) & &
2018-11-22 09:46:46 +01:00
( ( u64 ) place & 0xfff ) > = 0xff8 ;
2017-11-20 17:41:29 +00:00
}
2018-11-22 09:46:46 +01:00
struct plt_entry get_plt_entry ( u64 dst , void * pc ) ;
2017-11-20 17:41:29 +00:00
2022-08-30 11:48:31 +01:00
static inline const Elf_Shdr * find_section ( const Elf_Ehdr * hdr ,
const Elf_Shdr * sechdrs ,
const char * name )
2019-04-07 21:06:16 +02:00
{
2022-08-30 11:48:31 +01:00
const Elf_Shdr * s , * se ;
const char * secstrs = ( void * ) hdr + sechdrs [ hdr - > e_shstrndx ] . sh_offset ;
for ( s = sechdrs , se = sechdrs + hdr - > e_shnum ; s < se ; s + + ) {
if ( strcmp ( name , secstrs + s - > sh_name ) = = 0 )
return s ;
}
return NULL ;
2019-04-07 21:06:16 +02:00
}
2012-03-05 11:49:33 +00:00
# endif /* __ASM_MODULE_H */
