iv/linux
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
linux/arch/m68k/include/asm/m527xsim.h

296 lines
11 KiB
C
Raw Normal View History

Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 15:20:36 -07:00
/****************************************************************************/
/*
* m527xsim.h -- ColdFire 5270/5271 System Integration Module support.
*
* (C) Copyright 2004, Greg Ungerer (gerg@snapgear.com)
*/
/****************************************************************************/
#ifndef m527xsim_h
#define m527xsim_h
/****************************************************************************/
m68knommu: fix clock rate value reported for ColdFire 54xx parts The instruction timings of the ColdFire 54xx family parts are different to other version 4 parts (or version 2 or 3 parts for that matter too). Move the instruction timing setting into the ColdFire part specific headers, and set the 54xx value appropriately. Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2010-11-02 17:40:37 +10:00
#define CPU_NAME "COLDFIRE(m527x)"
#define CPU_INSTR_PER_JIFFY 3
m68knommu: remove ColdFire CLOCK_DIV config option The reality is that you do not need the abiltity to configure the clock divider for ColdFire CPUs. It is a fixed ratio on any given ColdFire family member. It is not the same for all ColdFire parts, but it is always the same in a model range. So hard define the divider for each supported ColdFire CPU type and remove the Kconfig option. Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-03-09 14:19:08 +10:00
#define MCF_BUSCLK (MCF_CLK / 2)
m68knommu: move ColdFire CPU names into their headers Move the ColdFire CPU names out of setup.c and into their repsective headers. That way when we add new ones we won't need to modify setup.c any more. Add the missing 548x CPU name. Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2010-11-02 17:13:27 +10:00
m68knommu: create bit definitions for the version 2 ColdFire cache controller The version 2 ColdFire CPU based cores all contain a similar cache controller unit. Create a set of bit flag definitions for the supporting registers. Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2010-11-09 10:12:29 +10:00
#include <asm/m52xxacr.h>
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 15:20:36 -07:00
/*
* Define the 5270/5271 SIM register set addresses.
*/
m68knommu: remove kludge seting of MCF_IPSBAR for ColdFire 54xx The ColdFire 54xx family shares the same interrupt controller used on the 523x, 527x and 528x ColdFire parts, but it isn't offset relative to the IPSBAR register. The 54xx doesn't have an IPSBAR register. By including the base address of the peripheral registers in the register definitions (MCFICM_INTC0 and MCFICM_INTC1 in this case) we can avoid having to define a fake IPSBAR for the 54xx. And this makes the register address definitions of these more consistent, the majority of the other register address defines include the peripheral base address already. Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-03-05 22:17:17 +10:00
#define MCFICM_INTC0 (MCF_IPSBAR + 0x0c00) /* Base for Interrupt Ctrl 0 */
#define MCFICM_INTC1 (MCF_IPSBAR + 0x0d00) /* Base for Interrupt Ctrl 1 */
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 15:20:36 -07:00
#define MCFINTC_IPRH 0x00 /* Interrupt pending 32-63 */
#define MCFINTC_IPRL 0x04 /* Interrupt pending 1-31 */
#define MCFINTC_IMRH 0x08 /* Interrupt mask 32-63 */
#define MCFINTC_IMRL 0x0c /* Interrupt mask 1-31 */
#define MCFINTC_INTFRCH 0x10 /* Interrupt force 32-63 */
#define MCFINTC_INTFRCL 0x14 /* Interrupt force 1-31 */
#define MCFINTC_IRLR 0x18 /* */
#define MCFINTC_IACKL 0x19 /* */
#define MCFINTC_ICR0 0x40 /* Base ICR register */
#define MCFINT_VECBASE 64 /* Vector base number */
#define MCFINT_UART0 13 /* Interrupt number for UART0 */
#define MCFINT_UART1 14 /* Interrupt number for UART1 */
#define MCFINT_UART2 15 /* Interrupt number for UART2 */
m68knommu: Coldfire QSPI platform support Since Grant has added the coldfire-qspi driver to next-spi, here is the platform support for the parts that have qspi hardware. This sets up gpio to do the spi chip select using the default chip select pins; it should be trivial for boards that require different or additional spi chip selects to use other gpios as needed. Signed-off-by: Steven King <sfking@fdwdc.com> Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2010-01-22 12:43:03 -08:00
#define MCFINT_QSPI 18 /* Interrupt number for QSPI */
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 15:20:36 -07:00
#define MCFINT_PIT1 36 /* Interrupt number for PIT1 */
/*
* SDRAM configuration registers.
*/
[PATCH] m68knommu: allow for SDRAM and GPIO differences on 5270/1 and 5274/5 processors Allow for differences in the SDRAM controller setup and GPIO pin setup of the 5270/1 and 5274/5 parts. With separate config options for each now this no longer needs to be board specific. Signed-off-by: Greg Ungerer <gerg@uclinux.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-12 11:18:10 +10:00
#ifdef CONFIG_M5271
m68knommu: clean up use of MBAR for DRAM registers on ColdFire start In some of the RAM size autodetection code on ColdFire CPU startup we reference DRAM registers relative to the MBAR register. Not all of the supported ColdFire CPUs have an MBAR, and currently this works because we fake an MBAR address on those registers. In an effort to clean this up, and eventually remove the fake MBAR setting make the DRAM register address definitions actually contain the MBAR (or IPSBAR as appropriate) value as required. Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-03-06 23:01:46 +10:00
#define MCFSIM_DCR (MCF_IPSBAR + 0x40) /* Control */
#define MCFSIM_DACR0 (MCF_IPSBAR + 0x48) /* Base address 0 */
#define MCFSIM_DMR0 (MCF_IPSBAR + 0x4c) /* Address mask 0 */
#define MCFSIM_DACR1 (MCF_IPSBAR + 0x50) /* Base address 1 */
#define MCFSIM_DMR1 (MCF_IPSBAR + 0x54) /* Address mask 1 */
[PATCH] m68knommu: allow for SDRAM and GPIO differences on 5270/1 and 5274/5 processors Allow for differences in the SDRAM controller setup and GPIO pin setup of the 5270/1 and 5274/5 parts. With separate config options for each now this no longer needs to be board specific. Signed-off-by: Greg Ungerer <gerg@uclinux.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-12 11:18:10 +10:00
#endif
#ifdef CONFIG_M5275
m68knommu: clean up use of MBAR for DRAM registers on ColdFire start In some of the RAM size autodetection code on ColdFire CPU startup we reference DRAM registers relative to the MBAR register. Not all of the supported ColdFire CPUs have an MBAR, and currently this works because we fake an MBAR address on those registers. In an effort to clean this up, and eventually remove the fake MBAR setting make the DRAM register address definitions actually contain the MBAR (or IPSBAR as appropriate) value as required. Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-03-06 23:01:46 +10:00
#define MCFSIM_DMR (MCF_IPSBAR + 0x40) /* Mode */
#define MCFSIM_DCR (MCF_IPSBAR + 0x44) /* Control */
#define MCFSIM_DCFG1 (MCF_IPSBAR + 0x48) /* Configuration 1 */
#define MCFSIM_DCFG2 (MCF_IPSBAR + 0x4c) /* Configuration 2 */
#define MCFSIM_DBAR0 (MCF_IPSBAR + 0x50) /* Base address 0 */
#define MCFSIM_DMR0 (MCF_IPSBAR + 0x54) /* Address mask 0 */
#define MCFSIM_DBAR1 (MCF_IPSBAR + 0x58) /* Base address 1 */
#define MCFSIM_DMR1 (MCF_IPSBAR + 0x5c) /* Address mask 1 */
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 15:20:36 -07:00
#endif
m68knommu: move ColdFire DMA register addresses to per-cpu headers The base addresses of the ColdFire DMA unit registers belong with all the other address definitions in the per-cpu headers. The current definitions assume they are relative to an MBAR register. Not all ColdFire CPUs have an MBAR register. A clean address define can only be acheived in the per-cpu headers along with all the other chips peripheral base addresses. Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-03-06 00:54:36 +10:00
/*
* DMA unit base addresses.
*/
#define MCFDMA_BASE0 (MCF_IPSBAR + 0x100)
#define MCFDMA_BASE1 (MCF_IPSBAR + 0x140)
#define MCFDMA_BASE2 (MCF_IPSBAR + 0x180)
#define MCFDMA_BASE3 (MCF_IPSBAR + 0x1C0)
m68knommu: move UART addressing to part specific includes The ColdFire UART base addresses varies between the different ColdFire family members. Instead of keeping the base addresses with the UART definitions keep them with the other addresses definitions for each ColdFire part. The motivation for this move is so that when we add new ColdFire part definitions, they are all in a single file (and we shouldn't normally need to modify the UART definitions in mcfuart.h at all). Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2010-11-03 12:50:30 +10:00
/*
* UART module.
*/
m68knommu: remove use of MBAR value for ColdFire 527x peripheral addressing The ColdFire 527x family of CPUs does not have an MBAR register, so don't define its peripheral addresses relative to one. Its internal peripherals are relative to the IPSBAR register, so make sure to use that. Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-03-06 00:13:17 +10:00
#define MCFUART_BASE1 (MCF_IPSBAR + 0x200)
#define MCFUART_BASE2 (MCF_IPSBAR + 0x240)
#define MCFUART_BASE3 (MCF_IPSBAR + 0x280)
/*
* FEC ethernet module.
*/
#define MCFFEC_BASE0 (MCF_IPSBAR + 0x1000)
#define MCFFEC_SIZE0 0x800
#define MCFFEC_BASE1 (MCF_IPSBAR + 0x1800)
#define MCFFEC_SIZE1 0x800
generic GPIO support for the Freescale Coldfire 527x. Add support for the 5271 & 5275. Signed-off-by: Steven King <sfking@fdwdc.com> Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2009-06-19 18:11:06 -07:00
#ifdef CONFIG_M5271
#define MCFGPIO_PODR_ADDR (MCF_IPSBAR + 0x100000)
#define MCFGPIO_PODR_DATAH (MCF_IPSBAR + 0x100001)
#define MCFGPIO_PODR_DATAL (MCF_IPSBAR + 0x100002)
#define MCFGPIO_PODR_BUSCTL (MCF_IPSBAR + 0x100003)
#define MCFGPIO_PODR_BS (MCF_IPSBAR + 0x100004)
#define MCFGPIO_PODR_CS (MCF_IPSBAR + 0x100005)
#define MCFGPIO_PODR_SDRAM (MCF_IPSBAR + 0x100006)
#define MCFGPIO_PODR_FECI2C (MCF_IPSBAR + 0x100007)
#define MCFGPIO_PODR_UARTH (MCF_IPSBAR + 0x100008)
#define MCFGPIO_PODR_UARTL (MCF_IPSBAR + 0x100009)
#define MCFGPIO_PODR_QSPI (MCF_IPSBAR + 0x10000A)
#define MCFGPIO_PODR_TIMER (MCF_IPSBAR + 0x10000B)
#define MCFGPIO_PDDR_ADDR (MCF_IPSBAR + 0x100010)
#define MCFGPIO_PDDR_DATAH (MCF_IPSBAR + 0x100011)
#define MCFGPIO_PDDR_DATAL (MCF_IPSBAR + 0x100012)
#define MCFGPIO_PDDR_BUSCTL (MCF_IPSBAR + 0x100013)
#define MCFGPIO_PDDR_BS (MCF_IPSBAR + 0x100014)
#define MCFGPIO_PDDR_CS (MCF_IPSBAR + 0x100015)
#define MCFGPIO_PDDR_SDRAM (MCF_IPSBAR + 0x100016)
#define MCFGPIO_PDDR_FECI2C (MCF_IPSBAR + 0x100017)
#define MCFGPIO_PDDR_UARTH (MCF_IPSBAR + 0x100018)
#define MCFGPIO_PDDR_UARTL (MCF_IPSBAR + 0x100019)
#define MCFGPIO_PDDR_QSPI (MCF_IPSBAR + 0x10001A)
#define MCFGPIO_PDDR_TIMER (MCF_IPSBAR + 0x10001B)
#define MCFGPIO_PPDSDR_ADDR (MCF_IPSBAR + 0x100020)
#define MCFGPIO_PPDSDR_DATAH (MCF_IPSBAR + 0x100021)
#define MCFGPIO_PPDSDR_DATAL (MCF_IPSBAR + 0x100022)
#define MCFGPIO_PPDSDR_BUSCTL (MCF_IPSBAR + 0x100023)
#define MCFGPIO_PPDSDR_BS (MCF_IPSBAR + 0x100024)
#define MCFGPIO_PPDSDR_CS (MCF_IPSBAR + 0x100025)
#define MCFGPIO_PPDSDR_SDRAM (MCF_IPSBAR + 0x100026)
#define MCFGPIO_PPDSDR_FECI2C (MCF_IPSBAR + 0x100027)
#define MCFGPIO_PPDSDR_UARTH (MCF_IPSBAR + 0x100028)
#define MCFGPIO_PPDSDR_UARTL (MCF_IPSBAR + 0x100029)
#define MCFGPIO_PPDSDR_QSPI (MCF_IPSBAR + 0x10002A)
#define MCFGPIO_PPDSDR_TIMER (MCF_IPSBAR + 0x10002B)
#define MCFGPIO_PCLRR_ADDR (MCF_IPSBAR + 0x100030)
#define MCFGPIO_PCLRR_DATAH (MCF_IPSBAR + 0x100031)
#define MCFGPIO_PCLRR_DATAL (MCF_IPSBAR + 0x100032)
#define MCFGPIO_PCLRR_BUSCTL (MCF_IPSBAR + 0x100033)
#define MCFGPIO_PCLRR_BS (MCF_IPSBAR + 0x100034)
#define MCFGPIO_PCLRR_CS (MCF_IPSBAR + 0x100035)
#define MCFGPIO_PCLRR_SDRAM (MCF_IPSBAR + 0x100036)
#define MCFGPIO_PCLRR_FECI2C (MCF_IPSBAR + 0x100037)
#define MCFGPIO_PCLRR_UARTH (MCF_IPSBAR + 0x100038)
#define MCFGPIO_PCLRR_UARTL (MCF_IPSBAR + 0x100039)
#define MCFGPIO_PCLRR_QSPI (MCF_IPSBAR + 0x10003A)
#define MCFGPIO_PCLRR_TIMER (MCF_IPSBAR + 0x10003B)
/*
* Generic GPIO support
*/
#define MCFGPIO_PODR MCFGPIO_PODR_ADDR
#define MCFGPIO_PDDR MCFGPIO_PDDR_ADDR
#define MCFGPIO_PPDR MCFGPIO_PPDSDR_ADDR
#define MCFGPIO_SETR MCFGPIO_PPDSDR_ADDR
#define MCFGPIO_CLRR MCFGPIO_PCLRR_ADDR
#define MCFGPIO_PIN_MAX 100
#define MCFGPIO_IRQ_MAX 8
#define MCFGPIO_IRQ_VECBASE MCFINT_VECBASE
m68knommu: Coldfire QSPI platform support Since Grant has added the coldfire-qspi driver to next-spi, here is the platform support for the parts that have qspi hardware. This sets up gpio to do the spi chip select using the default chip select pins; it should be trivial for boards that require different or additional spi chip selects to use other gpios as needed. Signed-off-by: Steven King <sfking@fdwdc.com> Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2010-01-22 12:43:03 -08:00
#define MCFGPIO_PAR_QSPI (MCF_IPSBAR + 0x10004A)
#define MCFGPIO_PAR_TIMER (MCF_IPSBAR + 0x10004C)
generic GPIO support for the Freescale Coldfire 527x. Add support for the 5271 & 5275. Signed-off-by: Steven King <sfking@fdwdc.com> Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2009-06-19 18:11:06 -07:00
#endif
#ifdef CONFIG_M5275
#define MCFGPIO_PODR_BUSCTL (MCF_IPSBAR + 0x100004)
#define MCFGPIO_PODR_ADDR (MCF_IPSBAR + 0x100005)
#define MCFGPIO_PODR_CS (MCF_IPSBAR + 0x100008)
#define MCFGPIO_PODR_FEC0H (MCF_IPSBAR + 0x10000A)
#define MCFGPIO_PODR_FEC0L (MCF_IPSBAR + 0x10000B)
#define MCFGPIO_PODR_FECI2C (MCF_IPSBAR + 0x10000C)
#define MCFGPIO_PODR_QSPI (MCF_IPSBAR + 0x10000D)
#define MCFGPIO_PODR_SDRAM (MCF_IPSBAR + 0x10000E)
#define MCFGPIO_PODR_TIMERH (MCF_IPSBAR + 0x10000F)
#define MCFGPIO_PODR_TIMERL (MCF_IPSBAR + 0x100010)
#define MCFGPIO_PODR_UARTL (MCF_IPSBAR + 0x100011)
#define MCFGPIO_PODR_FEC1H (MCF_IPSBAR + 0x100012)
#define MCFGPIO_PODR_FEC1L (MCF_IPSBAR + 0x100013)
#define MCFGPIO_PODR_BS (MCF_IPSBAR + 0x100014)
#define MCFGPIO_PODR_IRQ (MCF_IPSBAR + 0x100015)
#define MCFGPIO_PODR_USBH (MCF_IPSBAR + 0x100016)
#define MCFGPIO_PODR_USBL (MCF_IPSBAR + 0x100017)
#define MCFGPIO_PODR_UARTH (MCF_IPSBAR + 0x100018)
#define MCFGPIO_PDDR_BUSCTL (MCF_IPSBAR + 0x100020)
#define MCFGPIO_PDDR_ADDR (MCF_IPSBAR + 0x100021)
#define MCFGPIO_PDDR_CS (MCF_IPSBAR + 0x100024)
#define MCFGPIO_PDDR_FEC0H (MCF_IPSBAR + 0x100026)
#define MCFGPIO_PDDR_FEC0L (MCF_IPSBAR + 0x100027)
#define MCFGPIO_PDDR_FECI2C (MCF_IPSBAR + 0x100028)
#define MCFGPIO_PDDR_QSPI (MCF_IPSBAR + 0x100029)
#define MCFGPIO_PDDR_SDRAM (MCF_IPSBAR + 0x10002A)
#define MCFGPIO_PDDR_TIMERH (MCF_IPSBAR + 0x10002B)
#define MCFGPIO_PDDR_TIMERL (MCF_IPSBAR + 0x10002C)
#define MCFGPIO_PDDR_UARTL (MCF_IPSBAR + 0x10002D)
#define MCFGPIO_PDDR_FEC1H (MCF_IPSBAR + 0x10002E)
#define MCFGPIO_PDDR_FEC1L (MCF_IPSBAR + 0x10002F)
#define MCFGPIO_PDDR_BS (MCF_IPSBAR + 0x100030)
#define MCFGPIO_PDDR_IRQ (MCF_IPSBAR + 0x100031)
#define MCFGPIO_PDDR_USBH (MCF_IPSBAR + 0x100032)
#define MCFGPIO_PDDR_USBL (MCF_IPSBAR + 0x100033)
#define MCFGPIO_PDDR_UARTH (MCF_IPSBAR + 0x100034)
#define MCFGPIO_PPDSDR_BUSCTL (MCF_IPSBAR + 0x10003C)
#define MCFGPIO_PPDSDR_ADDR (MCF_IPSBAR + 0x10003D)
#define MCFGPIO_PPDSDR_CS (MCF_IPSBAR + 0x100040)
#define MCFGPIO_PPDSDR_FEC0H (MCF_IPSBAR + 0x100042)
#define MCFGPIO_PPDSDR_FEC0L (MCF_IPSBAR + 0x100043)
#define MCFGPIO_PPDSDR_FECI2C (MCF_IPSBAR + 0x100044)
#define MCFGPIO_PPDSDR_QSPI (MCF_IPSBAR + 0x100045)
#define MCFGPIO_PPDSDR_SDRAM (MCF_IPSBAR + 0x100046)
#define MCFGPIO_PPDSDR_TIMERH (MCF_IPSBAR + 0x100047)
#define MCFGPIO_PPDSDR_TIMERL (MCF_IPSBAR + 0x100048)
#define MCFGPIO_PPDSDR_UARTL (MCF_IPSBAR + 0x100049)
#define MCFGPIO_PPDSDR_FEC1H (MCF_IPSBAR + 0x10004A)
#define MCFGPIO_PPDSDR_FEC1L (MCF_IPSBAR + 0x10004B)
#define MCFGPIO_PPDSDR_BS (MCF_IPSBAR + 0x10004C)
#define MCFGPIO_PPDSDR_IRQ (MCF_IPSBAR + 0x10004D)
#define MCFGPIO_PPDSDR_USBH (MCF_IPSBAR + 0x10004E)
#define MCFGPIO_PPDSDR_USBL (MCF_IPSBAR + 0x10004F)
#define MCFGPIO_PPDSDR_UARTH (MCF_IPSBAR + 0x100050)
#define MCFGPIO_PCLRR_BUSCTL (MCF_IPSBAR + 0x100058)
#define MCFGPIO_PCLRR_ADDR (MCF_IPSBAR + 0x100059)
#define MCFGPIO_PCLRR_CS (MCF_IPSBAR + 0x10005C)
#define MCFGPIO_PCLRR_FEC0H (MCF_IPSBAR + 0x10005E)
#define MCFGPIO_PCLRR_FEC0L (MCF_IPSBAR + 0x10005F)
#define MCFGPIO_PCLRR_FECI2C (MCF_IPSBAR + 0x100060)
#define MCFGPIO_PCLRR_QSPI (MCF_IPSBAR + 0x100061)
#define MCFGPIO_PCLRR_SDRAM (MCF_IPSBAR + 0x100062)
#define MCFGPIO_PCLRR_TIMERH (MCF_IPSBAR + 0x100063)
#define MCFGPIO_PCLRR_TIMERL (MCF_IPSBAR + 0x100064)
#define MCFGPIO_PCLRR_UARTL (MCF_IPSBAR + 0x100065)
#define MCFGPIO_PCLRR_FEC1H (MCF_IPSBAR + 0x100066)
#define MCFGPIO_PCLRR_FEC1L (MCF_IPSBAR + 0x100067)
#define MCFGPIO_PCLRR_BS (MCF_IPSBAR + 0x100068)
#define MCFGPIO_PCLRR_IRQ (MCF_IPSBAR + 0x100069)
#define MCFGPIO_PCLRR_USBH (MCF_IPSBAR + 0x10006A)
#define MCFGPIO_PCLRR_USBL (MCF_IPSBAR + 0x10006B)
#define MCFGPIO_PCLRR_UARTH (MCF_IPSBAR + 0x10006C)
/*
* Generic GPIO support
*/
#define MCFGPIO_PODR MCFGPIO_PODR_BUSCTL
#define MCFGPIO_PDDR MCFGPIO_PDDR_BUSCTL
#define MCFGPIO_PPDR MCFGPIO_PPDSDR_BUSCTL
#define MCFGPIO_SETR MCFGPIO_PPDSDR_BUSCTL
#define MCFGPIO_CLRR MCFGPIO_PCLRR_BUSCTL
#define MCFGPIO_PIN_MAX 148
#define MCFGPIO_IRQ_MAX 8
#define MCFGPIO_IRQ_VECBASE MCFINT_VECBASE
m68knommu: Coldfire QSPI platform support Since Grant has added the coldfire-qspi driver to next-spi, here is the platform support for the parts that have qspi hardware. This sets up gpio to do the spi chip select using the default chip select pins; it should be trivial for boards that require different or additional spi chip selects to use other gpios as needed. Signed-off-by: Steven King <sfking@fdwdc.com> Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2010-01-22 12:43:03 -08:00
#define MCFGPIO_PAR_QSPI (MCF_IPSBAR + 0x10007E)
generic GPIO support for the Freescale Coldfire 527x. Add support for the 5271 & 5275. Signed-off-by: Steven King <sfking@fdwdc.com> Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2009-06-19 18:11:06 -07:00
#endif
/*
m68knommu: move ColdFire PIT timer base addresses The PIT hardware timer module used in some ColdFire CPU's is not always addressed relative to an IPSBAR register. Parts like the ColdFire 5207 and 5208 have fixed peripheral addresses. So lets not define the register addresses of the PIT relative to an IPSBAR definition. Move the base address definitions into the per-part headers. This is a lot more consistent since all the other peripheral base addresses are defined in the per-part header files already. Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-03-05 23:32:35 +10:00
* PIT timer base addresses.
generic GPIO support for the Freescale Coldfire 527x. Add support for the 5271 & 5275. Signed-off-by: Steven King <sfking@fdwdc.com> Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2009-06-19 18:11:06 -07:00
*/
m68knommu: move ColdFire PIT timer base addresses The PIT hardware timer module used in some ColdFire CPU's is not always addressed relative to an IPSBAR register. Parts like the ColdFire 5207 and 5208 have fixed peripheral addresses. So lets not define the register addresses of the PIT relative to an IPSBAR definition. Move the base address definitions into the per-part headers. This is a lot more consistent since all the other peripheral base addresses are defined in the per-part header files already. Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-03-05 23:32:35 +10:00
#define MCFPIT_BASE1 (MCF_IPSBAR + 0x150000)
#define MCFPIT_BASE2 (MCF_IPSBAR + 0x160000)
#define MCFPIT_BASE3 (MCF_IPSBAR + 0x170000)
#define MCFPIT_BASE4 (MCF_IPSBAR + 0x180000)
generic GPIO support for the Freescale Coldfire 527x. Add support for the 5271 & 5275. Signed-off-by: Steven King <sfking@fdwdc.com> Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2009-06-19 18:11:06 -07:00
m68knommu: move ColdFire PIT timer base addresses The PIT hardware timer module used in some ColdFire CPU's is not always addressed relative to an IPSBAR register. Parts like the ColdFire 5207 and 5208 have fixed peripheral addresses. So lets not define the register addresses of the PIT relative to an IPSBAR definition. Move the base address definitions into the per-part headers. This is a lot more consistent since all the other peripheral base addresses are defined in the per-part header files already. Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-03-05 23:32:35 +10:00
/*
* EPort
*/
m68knommu: external interrupt support to ColdFire intc-2 controller The EDGE Port module of some ColdFire parts using the intc-2 interrupt controller provides support for 7 external interrupts. These interrupts go off-chip (that is they are not for internal peripherals). They need some special handling and have some extra setup registers. Add code to support them. Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-03-11 17:06:58 +10:00
#define MCFEPORT_EPPAR (MCF_IPSBAR + 0x130000)
generic GPIO support for the Freescale Coldfire 527x. Add support for the 5271 & 5275. Signed-off-by: Steven King <sfking@fdwdc.com> Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2009-06-19 18:11:06 -07:00
#define MCFEPORT_EPDDR (MCF_IPSBAR + 0x130002)
m68knommu: external interrupt support to ColdFire intc-2 controller The EDGE Port module of some ColdFire parts using the intc-2 interrupt controller provides support for 7 external interrupts. These interrupts go off-chip (that is they are not for internal peripherals). They need some special handling and have some extra setup registers. Add code to support them. Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-03-11 17:06:58 +10:00
#define MCFEPORT_EPIER (MCF_IPSBAR + 0x130003)
generic GPIO support for the Freescale Coldfire 527x. Add support for the 5271 & 5275. Signed-off-by: Steven King <sfking@fdwdc.com> Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2009-06-19 18:11:06 -07:00
#define MCFEPORT_EPDR (MCF_IPSBAR + 0x130004)
#define MCFEPORT_EPPDR (MCF_IPSBAR + 0x130005)
m68knommu: external interrupt support to ColdFire intc-2 controller The EDGE Port module of some ColdFire parts using the intc-2 interrupt controller provides support for 7 external interrupts. These interrupts go off-chip (that is they are not for internal peripherals). They need some special handling and have some extra setup registers. Add code to support them. Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-03-11 17:06:58 +10:00
#define MCFEPORT_EPFR (MCF_IPSBAR + 0x130006)
generic GPIO support for the Freescale Coldfire 527x. Add support for the 5271 & 5275. Signed-off-by: Steven King <sfking@fdwdc.com> Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2009-06-19 18:11:06 -07:00
[PATCH] m68knommu: allow for SDRAM and GPIO differences on 5270/1 and 5274/5 processors Allow for differences in the SDRAM controller setup and GPIO pin setup of the 5270/1 and 5274/5 parts. With separate config options for each now this no longer needs to be board specific. Signed-off-by: Greg Ungerer <gerg@uclinux.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-12 11:18:10 +10:00
/*
* GPIO pins setups to enable the UARTs.
*/
#ifdef CONFIG_M5271
#define MCF_GPIO_PAR_UART 0x100048 /* PAR UART address */
#define UART0_ENABLE_MASK 0x000f
#define UART1_ENABLE_MASK 0x0ff0
#define UART2_ENABLE_MASK 0x3000
#endif
#ifdef CONFIG_M5275
#define MCF_GPIO_PAR_UART 0x10007c /* PAR UART address */
#define UART0_ENABLE_MASK 0x000f
#define UART1_ENABLE_MASK 0x00f0
#define UART2_ENABLE_MASK 0x3f00
#endif
m68knommu: move CPU reset code for the 527x ColdFire into its platform code Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2009-04-30 23:06:45 +10:00
/*
Fix common misspellings Fixes generated by 'codespell' and manually reviewed. Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-30 22:57:33 -03:00
* Reset Control Unit (relative to IPSBAR).
m68knommu: move CPU reset code for the 527x ColdFire into its platform code Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2009-04-30 23:06:45 +10:00
*/
#define MCF_RCR 0x110000
#define MCF_RSR 0x110001
#define MCF_RCR_SWRESET 0x80 /* Software reset bit */
#define MCF_RCR_FRCSTOUT 0x40 /* Force external reset */
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 15:20:36 -07:00
/****************************************************************************/
#endif /* m527xsim_h */
Reference in New Issue Copy Permalink