linux/net/ethtool/pse-pd.c

165 lines
4.2 KiB
C
Raw Normal View History

ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 09:52:00 +03:00
// SPDX-License-Identifier: GPL-2.0-only
//
// ethtool interface for Ethernet PSE (Power Sourcing Equipment)
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 09:52:00 +03:00
// and PD (Powered Device)
//
// Copyright (c) 2022 Pengutronix, Oleksij Rempel <kernel@pengutronix.de>
//
#include "common.h"
#include "linux/pse-pd/pse.h"
#include "netlink.h"
#include <linux/ethtool_netlink.h>
#include <linux/ethtool.h>
#include <linux/phy.h>
struct pse_req_info {
struct ethnl_req_info base;
};
struct pse_reply_data {
struct ethnl_reply_data base;
struct pse_control_status status;
};
#define PSE_REPDATA(__reply_base) \
container_of(__reply_base, struct pse_reply_data, base)
/* PSE_GET */
const struct nla_policy ethnl_pse_get_policy[ETHTOOL_A_PSE_HEADER + 1] = {
[ETHTOOL_A_PSE_HEADER] = NLA_POLICY_NESTED(ethnl_header_policy),
};
static int pse_get_pse_attributes(struct net_device *dev,
struct netlink_ext_ack *extack,
struct pse_reply_data *data)
{
struct phy_device *phydev = dev->phydev;
if (!phydev) {
NL_SET_ERR_MSG(extack, "No PHY is attached");
return -EOPNOTSUPP;
}
if (!phydev->psec) {
NL_SET_ERR_MSG(extack, "No PSE is attached");
return -EOPNOTSUPP;
}
memset(&data->status, 0, sizeof(data->status));
return pse_ethtool_get_status(phydev->psec, extack, &data->status);
}
static int pse_prepare_data(const struct ethnl_req_info *req_base,
struct ethnl_reply_data *reply_base,
const struct genl_info *info)
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 09:52:00 +03:00
{
struct pse_reply_data *data = PSE_REPDATA(reply_base);
struct net_device *dev = reply_base->dev;
int ret;
ret = ethnl_ops_begin(dev);
if (ret < 0)
return ret;
ret = pse_get_pse_attributes(dev, info->extack, data);
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 09:52:00 +03:00
ethnl_ops_complete(dev);
return ret;
}
static int pse_reply_size(const struct ethnl_req_info *req_base,
const struct ethnl_reply_data *reply_base)
{
const struct pse_reply_data *data = PSE_REPDATA(reply_base);
const struct pse_control_status *st = &data->status;
int len = 0;
if (st->podl_admin_state > 0)
len += nla_total_size(sizeof(u32)); /* _PODL_PSE_ADMIN_STATE */
if (st->podl_pw_status > 0)
len += nla_total_size(sizeof(u32)); /* _PODL_PSE_PW_D_STATUS */
return len;
}
static int pse_fill_reply(struct sk_buff *skb,
const struct ethnl_req_info *req_base,
const struct ethnl_reply_data *reply_base)
{
const struct pse_reply_data *data = PSE_REPDATA(reply_base);
const struct pse_control_status *st = &data->status;
if (st->podl_admin_state > 0 &&
nla_put_u32(skb, ETHTOOL_A_PODL_PSE_ADMIN_STATE,
st->podl_admin_state))
return -EMSGSIZE;
if (st->podl_pw_status > 0 &&
nla_put_u32(skb, ETHTOOL_A_PODL_PSE_PW_D_STATUS,
st->podl_pw_status))
return -EMSGSIZE;
return 0;
}
/* PSE_SET */
const struct nla_policy ethnl_pse_set_policy[ETHTOOL_A_PSE_MAX + 1] = {
[ETHTOOL_A_PSE_HEADER] = NLA_POLICY_NESTED(ethnl_header_policy),
[ETHTOOL_A_PODL_PSE_ADMIN_CONTROL] =
NLA_POLICY_RANGE(NLA_U32, ETHTOOL_PODL_PSE_ADMIN_STATE_DISABLED,
ETHTOOL_PODL_PSE_ADMIN_STATE_ENABLED),
};
static int
ethnl_set_pse_validate(struct ethnl_req_info *req_info, struct genl_info *info)
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 09:52:00 +03:00
{
return !!info->attrs[ETHTOOL_A_PODL_PSE_ADMIN_CONTROL];
}
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 09:52:00 +03:00
static int
ethnl_set_pse(struct ethnl_req_info *req_info, struct genl_info *info)
{
struct net_device *dev = req_info->dev;
struct pse_control_config config = {};
struct nlattr **tb = info->attrs;
struct phy_device *phydev;
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 09:52:00 +03:00
/* this values are already validated by the ethnl_pse_set_policy */
config.admin_cotrol = nla_get_u32(tb[ETHTOOL_A_PODL_PSE_ADMIN_CONTROL]);
phydev = dev->phydev;
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 09:52:00 +03:00
if (!phydev) {
NL_SET_ERR_MSG(info->extack, "No PHY is attached");
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 09:52:00 +03:00
return -EOPNOTSUPP;
}
if (!phydev->psec) {
NL_SET_ERR_MSG(info->extack, "No PSE is attached");
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 09:52:00 +03:00
return -EOPNOTSUPP;
}
/* Return errno directly - PSE has no notification */
return pse_ethtool_set_config(phydev->psec, info->extack, &config);
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 09:52:00 +03:00
}
const struct ethnl_request_ops ethnl_pse_request_ops = {
.request_cmd = ETHTOOL_MSG_PSE_GET,
.reply_cmd = ETHTOOL_MSG_PSE_GET_REPLY,
.hdr_attr = ETHTOOL_A_PSE_HEADER,
.req_info_size = sizeof(struct pse_req_info),
.reply_data_size = sizeof(struct pse_reply_data),
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 09:52:00 +03:00
.prepare_data = pse_prepare_data,
.reply_size = pse_reply_size,
.fill_reply = pse_fill_reply,
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 09:52:00 +03:00
.set_validate = ethnl_set_pse_validate,
.set = ethnl_set_pse,
/* PSE has no notification */
};