2008-07-25 12:46:14 +04:00
/*
* max732x . c - I2C Port Expander with 8 / 16 I / O
*
* Copyright ( C ) 2007 Marvell International Ltd .
* Copyright ( C ) 2008 Jack Ren < jack . ren @ marvell . com >
* Copyright ( C ) 2008 Eric Miao < eric . miao @ marvell . com >
*
* Derived from drivers / gpio / pca953x . c
*
* This program is free software ; you can redistribute it and / or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation ; version 2 of the License .
*/
# include <linux/module.h>
# include <linux/init.h>
# include <linux/slab.h>
# include <linux/string.h>
# include <linux/gpio.h>
# include <linux/i2c.h>
# include <linux/i2c/max732x.h>
/*
* Each port of MAX732x ( including MAX7319 ) falls into one of the
* following three types :
*
* - Push Pull Output
* - Input
* - Open Drain I / O
*
* designated by ' O ' , ' I ' and ' P ' individually according to MAXIM ' s
* datasheets .
*
* There are two groups of I / O ports , each group usually includes
* up to 8 I / O ports , and is accessed by a specific I2C address :
*
* - Group A : by I2C address 0 b ' 110 xxxx
* - Group B : by I2C address 0 b ' 101 xxxx
*
* where ' xxxx ' is decided by the connections of pin AD2 / AD0 . The
* address used also affects the initial state of output signals .
*
* Within each group of ports , there are five known combinations of
* I / O ports : 4 I4O , 4 P4O , 8 I , 8 P , 8 O , see the definitions below for
* the detailed organization of these ports .
*
* GPIO numbers start from ' gpio_base + 0 ' to ' gpio_base + 8 / 16 ' ,
* and GPIOs from GROUP_A are numbered before those from GROUP_B
* ( if there are two groups ) .
*
* NOTE : MAX7328 / MAX7329 are drop - in replacements for PCF8574 / a , so
* they are not supported by this driver .
*/
# define PORT_NONE 0x0 /* '/' No Port */
# define PORT_OUTPUT 0x1 /* 'O' Push-Pull, Output Only */
# define PORT_INPUT 0x2 /* 'I' Input Only */
# define PORT_OPENDRAIN 0x3 /* 'P' Open-Drain, I/O */
# define IO_4I4O 0x5AA5 /* O7 O6 I5 I4 I3 I2 O1 O0 */
# define IO_4P4O 0x5FF5 /* O7 O6 P5 P4 P3 P2 O1 O0 */
# define IO_8I 0xAAAA /* I7 I6 I5 I4 I3 I2 I1 I0 */
# define IO_8P 0xFFFF /* P7 P6 P5 P4 P3 P2 P1 P0 */
# define IO_8O 0x5555 /* O7 O6 O5 O4 O3 O2 O1 O0 */
# define GROUP_A(x) ((x) & 0xffff) /* I2C Addr: 0b'110xxxx */
# define GROUP_B(x) ((x) << 16) /* I2C Addr: 0b'101xxxx */
static const struct i2c_device_id max732x_id [ ] = {
{ " max7319 " , GROUP_A ( IO_8I ) } ,
{ " max7320 " , GROUP_B ( IO_8O ) } ,
{ " max7321 " , GROUP_A ( IO_8P ) } ,
{ " max7322 " , GROUP_A ( IO_4I4O ) } ,
{ " max7323 " , GROUP_A ( IO_4P4O ) } ,
{ " max7324 " , GROUP_A ( IO_8I ) | GROUP_B ( IO_8O ) } ,
{ " max7325 " , GROUP_A ( IO_8P ) | GROUP_B ( IO_8O ) } ,
{ " max7326 " , GROUP_A ( IO_4I4O ) | GROUP_B ( IO_8O ) } ,
{ " max7327 " , GROUP_A ( IO_4P4O ) | GROUP_B ( IO_8O ) } ,
{ } ,
} ;
MODULE_DEVICE_TABLE ( i2c , max732x_id ) ;
struct max732x_chip {
struct gpio_chip gpio_chip ;
struct i2c_client * client ; /* "main" client */
struct i2c_client * client_dummy ;
struct i2c_client * client_group_a ;
struct i2c_client * client_group_b ;
unsigned int mask_group_a ;
unsigned int dir_input ;
unsigned int dir_output ;
struct mutex lock ;
uint8_t reg_out [ 2 ] ;
} ;
static int max732x_write ( struct max732x_chip * chip , int group_a , uint8_t val )
{
struct i2c_client * client ;
int ret ;
client = group_a ? chip - > client_group_a : chip - > client_group_b ;
ret = i2c_smbus_write_byte ( client , val ) ;
if ( ret < 0 ) {
dev_err ( & client - > dev , " failed writing \n " ) ;
return ret ;
}
return 0 ;
}
static int max732x_read ( struct max732x_chip * chip , int group_a , uint8_t * val )
{
struct i2c_client * client ;
int ret ;
client = group_a ? chip - > client_group_a : chip - > client_group_b ;
ret = i2c_smbus_read_byte ( client ) ;
if ( ret < 0 ) {
dev_err ( & client - > dev , " failed reading \n " ) ;
return ret ;
}
* val = ( uint8_t ) ret ;
return 0 ;
}
static inline int is_group_a ( struct max732x_chip * chip , unsigned off )
{
return ( 1u < < off ) & chip - > mask_group_a ;
}
static int max732x_gpio_get_value ( struct gpio_chip * gc , unsigned off )
{
struct max732x_chip * chip ;
uint8_t reg_val ;
int ret ;
chip = container_of ( gc , struct max732x_chip , gpio_chip ) ;
ret = max732x_read ( chip , is_group_a ( chip , off ) , & reg_val ) ;
if ( ret < 0 )
return 0 ;
return reg_val & ( 1u < < ( off & 0x7 ) ) ;
}
static void max732x_gpio_set_value ( struct gpio_chip * gc , unsigned off , int val )
{
struct max732x_chip * chip ;
uint8_t reg_out , mask = 1u < < ( off & 0x7 ) ;
int ret ;
chip = container_of ( gc , struct max732x_chip , gpio_chip ) ;
mutex_lock ( & chip - > lock ) ;
reg_out = ( off > 7 ) ? chip - > reg_out [ 1 ] : chip - > reg_out [ 0 ] ;
reg_out = ( val ) ? reg_out | mask : reg_out & ~ mask ;
ret = max732x_write ( chip , is_group_a ( chip , off ) , reg_out ) ;
if ( ret < 0 )
goto out ;
/* update the shadow register then */
if ( off > 7 )
chip - > reg_out [ 1 ] = reg_out ;
else
chip - > reg_out [ 0 ] = reg_out ;
out :
mutex_unlock ( & chip - > lock ) ;
}
static int max732x_gpio_direction_input ( struct gpio_chip * gc , unsigned off )
{
struct max732x_chip * chip ;
unsigned int mask = 1u < < off ;
chip = container_of ( gc , struct max732x_chip , gpio_chip ) ;
if ( ( mask & chip - > dir_input ) = = 0 ) {
dev_dbg ( & chip - > client - > dev , " %s port %d is output only \n " ,
chip - > client - > name , off ) ;
return - EACCES ;
}
return 0 ;
}
static int max732x_gpio_direction_output ( struct gpio_chip * gc ,
unsigned off , int val )
{
struct max732x_chip * chip ;
unsigned int mask = 1u < < off ;
chip = container_of ( gc , struct max732x_chip , gpio_chip ) ;
if ( ( mask & chip - > dir_output ) = = 0 ) {
dev_dbg ( & chip - > client - > dev , " %s port %d is input only \n " ,
chip - > client - > name , off ) ;
return - EACCES ;
}
max732x_gpio_set_value ( gc , off , val ) ;
return 0 ;
}
static int __devinit max732x_setup_gpio ( struct max732x_chip * chip ,
const struct i2c_device_id * id ,
unsigned gpio_start )
{
struct gpio_chip * gc = & chip - > gpio_chip ;
uint32_t id_data = id - > driver_data ;
int i , port = 0 ;
for ( i = 0 ; i < 16 ; i + + , id_data > > = 2 ) {
unsigned int mask = 1 < < port ;
switch ( id_data & 0x3 ) {
case PORT_OUTPUT :
chip - > dir_output | = mask ;
break ;
case PORT_INPUT :
chip - > dir_input | = mask ;
break ;
case PORT_OPENDRAIN :
chip - > dir_output | = mask ;
chip - > dir_input | = mask ;
break ;
default :
continue ;
}
if ( i < 8 )
chip - > mask_group_a | = mask ;
port + + ;
}
if ( chip - > dir_input )
gc - > direction_input = max732x_gpio_direction_input ;
if ( chip - > dir_output ) {
gc - > direction_output = max732x_gpio_direction_output ;
gc - > set = max732x_gpio_set_value ;
}
gc - > get = max732x_gpio_get_value ;
gc - > can_sleep = 1 ;
gc - > base = gpio_start ;
gc - > ngpio = port ;
gc - > label = chip - > client - > name ;
gc - > owner = THIS_MODULE ;
return port ;
}
static int __devinit max732x_probe ( struct i2c_client * client ,
const struct i2c_device_id * id )
{
struct max732x_platform_data * pdata ;
struct max732x_chip * chip ;
struct i2c_client * c ;
uint16_t addr_a , addr_b ;
int ret , nr_port ;
pdata = client - > dev . platform_data ;
2009-01-16 00:50:45 +03:00
if ( pdata = = NULL ) {
dev_dbg ( & client - > dev , " no platform data \n " ) ;
return - EINVAL ;
}
2008-07-25 12:46:14 +04:00
chip = kzalloc ( sizeof ( struct max732x_chip ) , GFP_KERNEL ) ;
if ( chip = = NULL )
return - ENOMEM ;
chip - > client = client ;
nr_port = max732x_setup_gpio ( chip , id , pdata - > gpio_base ) ;
addr_a = ( client - > addr & 0x0f ) | 0x60 ;
addr_b = ( client - > addr & 0x0f ) | 0x50 ;
switch ( client - > addr & 0x70 ) {
case 0x60 :
chip - > client_group_a = client ;
if ( nr_port > 7 ) {
c = i2c_new_dummy ( client - > adapter , addr_b ) ;
chip - > client_group_b = chip - > client_dummy = c ;
}
break ;
case 0x50 :
chip - > client_group_b = client ;
if ( nr_port > 7 ) {
c = i2c_new_dummy ( client - > adapter , addr_a ) ;
chip - > client_group_a = chip - > client_dummy = c ;
}
break ;
default :
dev_err ( & client - > dev , " invalid I2C address specified %02x \n " ,
client - > addr ) ;
ret = - EINVAL ;
goto out_failed ;
}
mutex_init ( & chip - > lock ) ;
max732x_read ( chip , is_group_a ( chip , 0 ) , & chip - > reg_out [ 0 ] ) ;
if ( nr_port > 7 )
max732x_read ( chip , is_group_a ( chip , 8 ) , & chip - > reg_out [ 1 ] ) ;
ret = gpiochip_add ( & chip - > gpio_chip ) ;
if ( ret )
goto out_failed ;
if ( pdata - > setup ) {
ret = pdata - > setup ( client , chip - > gpio_chip . base ,
chip - > gpio_chip . ngpio , pdata - > context ) ;
if ( ret < 0 )
dev_warn ( & client - > dev , " setup failed, %d \n " , ret ) ;
}
i2c_set_clientdata ( client , chip ) ;
return 0 ;
out_failed :
kfree ( chip ) ;
return ret ;
}
static int __devexit max732x_remove ( struct i2c_client * client )
{
struct max732x_platform_data * pdata = client - > dev . platform_data ;
struct max732x_chip * chip = i2c_get_clientdata ( client ) ;
int ret ;
if ( pdata - > teardown ) {
ret = pdata - > teardown ( client , chip - > gpio_chip . base ,
chip - > gpio_chip . ngpio , pdata - > context ) ;
if ( ret < 0 ) {
dev_err ( & client - > dev , " %s failed, %d \n " ,
" teardown " , ret ) ;
return ret ;
}
}
ret = gpiochip_remove ( & chip - > gpio_chip ) ;
if ( ret ) {
dev_err ( & client - > dev , " %s failed, %d \n " ,
" gpiochip_remove() " , ret ) ;
return ret ;
}
/* unregister any dummy i2c_client */
if ( chip - > client_dummy )
i2c_unregister_device ( chip - > client_dummy ) ;
kfree ( chip ) ;
return 0 ;
}
static struct i2c_driver max732x_driver = {
. driver = {
. name = " max732x " ,
. owner = THIS_MODULE ,
} ,
. probe = max732x_probe ,
. remove = __devexit_p ( max732x_remove ) ,
. id_table = max732x_id ,
} ;
static int __init max732x_init ( void )
{
return i2c_add_driver ( & max732x_driver ) ;
}
2008-10-16 09:03:13 +04:00
/* register after i2c postcore initcall and before
* subsys initcalls that may rely on these GPIOs
*/
subsys_initcall ( max732x_init ) ;
2008-07-25 12:46:14 +04:00
static void __exit max732x_exit ( void )
{
i2c_del_driver ( & max732x_driver ) ;
}
module_exit ( max732x_exit ) ;
MODULE_AUTHOR ( " Eric Miao <eric.miao@marvell.com> " ) ;
MODULE_DESCRIPTION ( " GPIO expander driver for MAX732X " ) ;
MODULE_LICENSE ( " GPL " ) ;