linux/drivers/ata/pata_triflex.c

/*
 * pata_triflex.c 	- Compaq PATA for new ATA layer
 *			  (C) 2005 Red Hat Inc
 *			  Alan Cox <alan@redhat.com>
 *
 * based upon
 *
 * triflex.c
 *
 * IDE Chipset driver for the Compaq TriFlex IDE controller.
 *
 * Known to work with the Compaq Workstation 5x00 series.
 *
 * Copyright (C) 2002 Hewlett-Packard Development Group, L.P.
 * Author: Torben Mathiasen <torben.mathiasen@hp.com>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 *
 * Loosely based on the piix & svwks drivers.
 *
 * Documentation:
 *	Not publically available.
 */

#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>

#define DRV_NAME "pata_triflex"
#define DRV_VERSION "0.2.8"

/**
 *	triflex_prereset		-	probe begin
 *	@ap: ATA port
 *	@deadline: deadline jiffies for the operation
 *
 *	Set up cable type and use generic probe init
 */

static int triflex_prereset(struct ata_port *ap, unsigned long deadline)
{
	static const struct pci_bits triflex_enable_bits[] = {
		{ 0x80, 1, 0x01, 0x01 },
		{ 0x80, 1, 0x02, 0x02 }
	};

	struct pci_dev *pdev = to_pci_dev(ap->host->dev);

	if (!pci_test_config_bits(pdev, &triflex_enable_bits[ap->port_no]))
		return -ENOENT;

	return ata_std_prereset(ap, deadline);
}



static void triflex_error_handler(struct ata_port *ap)
{
	ata_bmdma_drive_eh(ap, triflex_prereset, ata_std_softreset, NULL, ata_std_postreset);
}

/**
 *	triflex_load_timing		-	timing configuration
 *	@ap: ATA interface
 *	@adev: Device on the bus
 *	@speed: speed to configure
 *
 *	The Triflex has one set of timings per device per channel. This
 *	means we must do some switching. As the PIO and DMA timings don't
 *	match we have to do some reloading unlike PIIX devices where tuning
 *	tricks can avoid it.
 */

static void triflex_load_timing(struct ata_port *ap, struct ata_device *adev, int speed)
{
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	u32 timing = 0;
	u32 triflex_timing, old_triflex_timing;
	int channel_offset = ap->port_no ? 0x74: 0x70;
	unsigned int is_slave	= (adev->devno != 0);


	pci_read_config_dword(pdev, channel_offset, &old_triflex_timing);
	triflex_timing = old_triflex_timing;

	switch(speed)
	{
		case XFER_MW_DMA_2:
			timing = 0x0103;break;
		case XFER_MW_DMA_1:
			timing = 0x0203;break;
		case XFER_MW_DMA_0:
			timing = 0x0808;break;
		case XFER_SW_DMA_2:
		case XFER_SW_DMA_1:
		case XFER_SW_DMA_0:
			timing = 0x0F0F;break;
		case XFER_PIO_4:
			timing = 0x0202;break;
		case XFER_PIO_3:
			timing = 0x0204;break;
		case XFER_PIO_2:
			timing = 0x0404;break;
		case XFER_PIO_1:
			timing = 0x0508;break;
		case XFER_PIO_0:
			timing = 0x0808;break;
		default:
			BUG();
	}
	triflex_timing &= ~ (0xFFFF << (16 * is_slave));
	triflex_timing |= (timing << (16 * is_slave));

	if (triflex_timing != old_triflex_timing)
		pci_write_config_dword(pdev, channel_offset, triflex_timing);
}

/**
 *	triflex_set_piomode	-	set initial PIO mode data
 *	@ap: ATA interface
 *	@adev: ATA device
 *
 *	Use the timing loader to set up the PIO mode. We have to do this
 *	because DMA start/stop will only be called once DMA occurs. If there
 *	has been no DMA then the PIO timings are still needed.
 */
static void triflex_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
	triflex_load_timing(ap, adev, adev->pio_mode);
}

/**
 *	triflex_dma_start	-	DMA start callback
 *	@qc: Command in progress
 *
 *	Usually drivers set the DMA timing at the point the set_dmamode call
 *	is made. Triflex however requires we load new timings on the
 *	transition or keep matching PIO/DMA pairs (ie MWDMA2/PIO4 etc).
 *	We load the DMA timings just before starting DMA and then restore
 *	the PIO timing when the DMA is finished.
 */

static void triflex_bmdma_start(struct ata_queued_cmd *qc)
{
	triflex_load_timing(qc->ap, qc->dev, qc->dev->dma_mode);
	ata_bmdma_start(qc);
}

/**
 *	triflex_dma_stop	-	DMA stop callback
 *	@ap: ATA interface
 *	@adev: ATA device
 *
 *	We loaded new timings in dma_start, as a result we need to restore
 *	the PIO timings in dma_stop so that the next command issue gets the
 *	right clock values.
 */

static void triflex_bmdma_stop(struct ata_queued_cmd *qc)
{
	ata_bmdma_stop(qc);
	triflex_load_timing(qc->ap, qc->dev, qc->dev->pio_mode);
}

static struct scsi_host_template triflex_sht = {
	.module			= THIS_MODULE,
	.name			= DRV_NAME,
	.ioctl			= ata_scsi_ioctl,
	.queuecommand		= ata_scsi_queuecmd,
	.can_queue		= ATA_DEF_QUEUE,
	.this_id		= ATA_SHT_THIS_ID,
	.sg_tablesize		= LIBATA_MAX_PRD,
	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
	.emulated		= ATA_SHT_EMULATED,
	.use_clustering		= ATA_SHT_USE_CLUSTERING,
	.proc_name		= DRV_NAME,
	.dma_boundary		= ATA_DMA_BOUNDARY,
	.slave_configure	= ata_scsi_slave_config,
	.slave_destroy		= ata_scsi_slave_destroy,
	.bios_param		= ata_std_bios_param,
};

static struct ata_port_operations triflex_port_ops = {
	.port_disable	= ata_port_disable,
	.set_piomode	= triflex_set_piomode,
	.mode_filter	= ata_pci_default_filter,

	.tf_load	= ata_tf_load,
	.tf_read	= ata_tf_read,
	.check_status 	= ata_check_status,
	.exec_command	= ata_exec_command,
	.dev_select 	= ata_std_dev_select,

	.freeze		= ata_bmdma_freeze,
	.thaw		= ata_bmdma_thaw,
	.error_handler	= triflex_error_handler,
	.post_internal_cmd = ata_bmdma_post_internal_cmd,
	.cable_detect	= ata_cable_40wire,

	.bmdma_setup 	= ata_bmdma_setup,
	.bmdma_start 	= triflex_bmdma_start,
	.bmdma_stop	= triflex_bmdma_stop,
	.bmdma_status 	= ata_bmdma_status,

	.qc_prep 	= ata_qc_prep,
	.qc_issue	= ata_qc_issue_prot,

	.data_xfer	= ata_data_xfer,

	.irq_handler	= ata_interrupt,
	.irq_clear	= ata_bmdma_irq_clear,
	.irq_on		= ata_irq_on,
	.irq_ack	= ata_irq_ack,

	.port_start	= ata_port_start,
};

static int triflex_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
	static struct ata_port_info info = {
		.sht = &triflex_sht,
		.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
		.pio_mask = 0x1f,
		.mwdma_mask = 0x07,
		.port_ops = &triflex_port_ops
	};
	static struct ata_port_info *port_info[2] = { &info, &info };
	static int printed_version;

	if (!printed_version++)
		dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n");

	return ata_pci_init_one(dev, port_info, 2);
}

static const struct pci_device_id triflex[] = {
	{ PCI_VDEVICE(COMPAQ, PCI_DEVICE_ID_COMPAQ_TRIFLEX_IDE), },

	{ },
};

static struct pci_driver triflex_pci_driver = {
	.name 		= DRV_NAME,
	.id_table	= triflex,
	.probe 		= triflex_init_one,
	.remove		= ata_pci_remove_one,
#ifdef CONFIG_PM
	.suspend	= ata_pci_device_suspend,
	.resume		= ata_pci_device_resume,
#endif
};

static int __init triflex_init(void)
{
	return pci_register_driver(&triflex_pci_driver);
}

static void __exit triflex_exit(void)
{
	pci_unregister_driver(&triflex_pci_driver);
}

MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Compaq Triflex");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, triflex);
MODULE_VERSION(DRV_VERSION);

module_init(triflex_init);
module_exit(triflex_exit);