linux/drivers/usb/image/Kconfig

# SPDX-License-Identifier: GPL-2.0
#
# USB Imaging devices configuration
#
comment "USB Imaging devices"

config USB_MDC800
	tristate "USB Mustek MDC800 Digital Camera support"
	---help---
	  Say Y here if you want to connect this type of still camera to
	  your computer's USB port. This driver can be used with gphoto 0.4.3
	  and higher (look at <http://www.gphoto.org/>).
	  To use it create a device node with "mknod /dev/mustek c 180 32" and
	  configure it in your software.

	  To compile this driver as a module, choose M here: the
	  module will be called mdc800.

config USB_MICROTEK
	tristate "Microtek X6USB scanner support"
	depends on SCSI
	help
	  Say Y here if you want support for the Microtek X6USB and
	  possibly the Phantom 336CX, Phantom C6 and ScanMaker V6U(S)L.
	  Support for anything but the X6 is experimental.
	  Please report failures and successes.
	  The scanner will appear as a scsi generic device to the rest
	  of the system. Scsi support is required.
	  This driver can be compiled as a module, called microtek.
USB: add missing SPDX lines to Kconfig and Makefiles There are a few remaining drivers/usb/ files that do not have SPDX identifiers in them, all of these are either Kconfig or Makefiles. Add the correct GPL-2.0 identifier to them to make scanning tools happy. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 2019-01-17 11:23:50 +03:00			`# SPDX-License-Identifier: GPL-2.0`
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! 2005-04-17 02:20:36 +04:00			`#`
typo fixes Most of these fixes were already submitted for old kernel versions, and were approved, but for some reason they never made it into the releases. Because this is a consolidation of a couple old missed patches, it touches both Kconfigs and documentation texts. Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Adrian Bunk <bunk@kernel.org> 2007-10-20 03:34:40 +04:00			`# USB Imaging devices configuration`
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! 2005-04-17 02:20:36 +04:00			`#`
			`comment "USB Imaging devices"`

			`config USB_MDC800`
USB: Remove EXPERIMENTAL designation from USB MDC800 support. Since support for the USB Mustek MDC800 Digital Camera has apparently been around since the beginning of the git repository, it's safe to assume it's no longer experimental. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> 2008-03-08 11:04:05 +03:00			`tristate "USB Mustek MDC800 Digital Camera support"`
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! 2005-04-17 02:20:36 +04:00			`---help---`
			`Say Y here if you want to connect this type of still camera to`
			`your computer's USB port. This driver can be used with gphoto 0.4.3`
			`and higher (look at <http://www.gphoto.org/>).`
			`To use it create a device node with "mknod /dev/mustek c 180 32" and`
			`configure it in your software.`

			`To compile this driver as a module, choose M here: the`
			`module will be called mdc800.`

			`config USB_MICROTEK`
			`tristate "Microtek X6USB scanner support"`
USB: regroup all depends on USB within an if USB block This patch removes the depends on USB from all config symbols in drivers/usb/host/Kconfig and replace that with an if USB / endif block as suggested by Alan Stern. Some source ... Kconfig lines have been shuffled around to permit a better regroupment of the Kconfig files depending on "config USB" item. No functionnal change is introduced. Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 2013-04-09 16:29:25 +04:00			`depends on SCSI`
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! 2005-04-17 02:20:36 +04:00			`help`
			`Say Y here if you want support for the Microtek X6USB and`
			`possibly the Phantom 336CX, Phantom C6 and ScanMaker V6U(S)L.`
			`Support for anything but the X6 is experimental.`
			`Please report failures and successes.`
			`The scanner will appear as a scsi generic device to the rest`
			`of the system. Scsi support is required.`
			`This driver can be compiled as a module, called microtek.`