2005-04-16 15:20:36 -07:00
/*
2008-08-05 16:14:15 +01:00
* arch / arm / mach - sa1100 / include / mach / simpad . h
2005-04-16 15:20:36 -07:00
*
* based of assabet . h same as HUW_Webpanel
*
* This file contains the hardware specific definitions for SIMpad
*
* 2001 / 05 / 14 Juergen Messerer < juergen . messerer @ freesurf . ch >
*/
# ifndef __ASM_ARCH_SIMPAD_H
# define __ASM_ARCH_SIMPAD_H
# define GPIO_UART1_RTS GPIO_GPIO14
# define GPIO_UART1_DTR GPIO_GPIO7
# define GPIO_UART1_CTS GPIO_GPIO8
# define GPIO_UART1_DCD GPIO_GPIO23
# define GPIO_UART1_DSR GPIO_GPIO6
# define GPIO_UART3_RTS GPIO_GPIO12
# define GPIO_UART3_DTR GPIO_GPIO16
# define GPIO_UART3_CTS GPIO_GPIO13
# define GPIO_UART3_DCD GPIO_GPIO18
# define GPIO_UART3_DSR GPIO_GPIO17
# define GPIO_POWER_BUTTON GPIO_GPIO0
# define GPIO_UCB1300_IRQ GPIO_GPIO22 /* UCB GPIO and touchscreen */
# define IRQ_UART1_CTS IRQ_GPIO15
# define IRQ_UART1_DCD GPIO_GPIO23
# define IRQ_UART1_DSR GPIO_GPIO6
# define IRQ_UART3_CTS GPIO_GPIO13
# define IRQ_UART3_DCD GPIO_GPIO18
# define IRQ_UART3_DSR GPIO_GPIO17
# define IRQ_GPIO_UCB1300_IRQ IRQ_GPIO22
# define IRQ_GPIO_POWER_BUTTON IRQ_GPIO0
/*--- PCMCIA ---*/
# define GPIO_CF_CD GPIO_GPIO24
# define GPIO_CF_IRQ GPIO_GPIO1
# define IRQ_GPIO_CF_IRQ IRQ_GPIO1
# define IRQ_GPIO_CF_CD IRQ_GPIO24
/*--- SmartCard ---*/
# define GPIO_SMART_CARD GPIO_GPIO10
# define IRQ_GPIO_SMARD_CARD IRQ_GPIO10
// CS3 Latch is write only, a shadow is necessary
# define CS3BUSTYPE unsigned volatile long
# define CS3_BASE 0xf1000000
# define VCC_5V_EN 0x0001 // For 5V PCMCIA
# define VCC_3V_EN 0x0002 // FOR 3.3V PCMCIA
# define EN1 0x0004 // This is only for EPROM's
# define EN0 0x0008 // Both should be enable for 3.3V or 5V
# define DISPLAY_ON 0x0010
# define PCMCIA_BUFF_DIS 0x0020
# define MQ_RESET 0x0040
# define PCMCIA_RESET 0x0080
# define DECT_POWER_ON 0x0100
# define IRDA_SD 0x0200 // Shutdown for powersave
# define RS232_ON 0x0400
# define SD_MEDIAQ 0x0800 // Shutdown for powersave
# define LED2_ON 0x1000
# define IRDA_MODE 0x2000 // Fast/Slow IrDA mode
# define ENABLE_5V 0x4000 // Enable 5V circuit
# define RESET_SIMCARD 0x8000
# define RS232_ENABLE 0x0440
# define PCMCIAMASK 0x402f
struct simpad_battery {
unsigned char ac_status ; /* line connected yes/no */
unsigned char status ; /* battery loading yes/no */
unsigned char percentage ; /* percentage loaded */
unsigned short life ; /* life till empty */
} ;
/* These should match the apm_bios.h definitions */
# define SIMPAD_AC_STATUS_AC_OFFLINE 0x00
# define SIMPAD_AC_STATUS_AC_ONLINE 0x01
# define SIMPAD_AC_STATUS_AC_BACKUP 0x02 /* What does this mean? */
# define SIMPAD_AC_STATUS_AC_UNKNOWN 0xff
/* These bitfields are rarely "or'd" together */
# define SIMPAD_BATT_STATUS_HIGH 0x01
# define SIMPAD_BATT_STATUS_LOW 0x02
# define SIMPAD_BATT_STATUS_CRITICAL 0x04
# define SIMPAD_BATT_STATUS_CHARGING 0x08
# define SIMPAD_BATT_STATUS_CHARGE_MAIN 0x10
# define SIMPAD_BATT_STATUS_DEAD 0x20 /* Battery will not charge */
# define SIMPAD_BATT_NOT_INSTALLED 0x20 /* For expansion pack batteries */
# define SIMPAD_BATT_STATUS_FULL 0x40 /* Battery fully charged (and connected to AC) */
# define SIMPAD_BATT_STATUS_NOBATT 0x80
# define SIMPAD_BATT_STATUS_UNKNOWN 0xff
extern int simpad_get_battery ( struct simpad_battery * ) ;
# endif // __ASM_ARCH_SIMPAD_H
