drm: Add GUD USB Display driver
This adds a USB display driver with the intention that it can be
used with future USB interfaced low end displays/adapters. The Linux
gadget device driver will serve as the canonical device implementation.
The following DRM properties are supported:
- Plane rotation
- Connector TV properties
There is also support for backlight brightness exposed as a backlight
device.
Display modes can be made available to the host driver either as DRM
display modes or through EDID. If both are present, EDID is just passed
on to userspace.
Performance is preferred over color depth, so if the device supports
RGB565, DRM_CAP_DUMB_PREFERRED_DEPTH will return 16.
If the device transfer buffer can't fit an uncompressed framebuffer
update, the update is split up into parts that do fit.
Optimal user experience is achieved by providing damage reports either by
setting FB_DAMAGE_CLIPS on pageflips or calling DRM_IOCTL_MODE_DIRTYFB.
LZ4 compression is used if the device supports it.
The driver supports a one bit monochrome transfer format: R1. This is not
implemented in the gadget driver. It is added in preparation for future
monochrome e-ink displays.
The driver is MIT licensed to smooth the path for any BSD port of the
driver.
v2:
- Use devm_drm_dev_alloc() and drmm_mode_config_init()
- drm_fbdev_generic_setup: Use preferred_bpp=0, 16 was a copy paste error
- The drm_backlight_helper is dropped, copy in the code
- Support protocol version backwards compatibility for device
v3:
- Use donated Openmoko USB pid
- Use direct compression from framebuffer when pitch matches, not only on
full frames, so split updates can benefit
- Use __le16 in struct gud_drm_req_get_connector_status
- Set edid property when the device only provides edid
- Clear compression fields in struct gud_drm_req_set_buffer
- Fix protocol version negotiation
- Remove mode->vrefresh, it's calculated
v4:
- Drop the status req polling which was a workaround for something that
turned out to be a dwc2 udc driver problem
- Add a flag for the Linux gadget to require a status request on
SET operations. Other devices will only get status req on STALL errors
- Use protocol specific error codes (Peter)
- Add a flag for devices that want to receive the entire framebuffer on
each flush (Lubomir)
- Retry a failed framebuffer flush
- If mode has changed wait for worker and clear pending damage before
queuing up new damage, fb width/height might have changed
- Increase error counter on bulk transfer failures
- Use DRM_MODE_CONNECTOR_USB
- Handle R1 kmalloc error (Peter)
- Don't try and replicate the USB get descriptor request standard for the
display descriptor (Peter)
- Make max_buffer_size optional (Peter), drop the pow2 requirement since
it's not necessary anymore.
- Don't pre-alloc a control request buffer, it was only 4k
- Let gud.h describe the whole protocol explicitly and don't let DRM
leak into it (Peter)
- Drop display mode .hskew and .vscan from the protocol
- Shorten names: s/GUD_DRM_/GUD_/ s/gud_drm_/gud_/ (Peter)
- Fix gud_pipe_check() connector picking when switching connector
- Drop gud_drm_driver_gem_create_object() cached is default now
- Retrieve USB device from struct drm_device.dev instead of keeping a
pointer
- Honour fb->offsets[0]
- Fix mode fetching when connector status is forced
- Check EDID length reported by the device
- Use drm_do_get_edid() so userspace can overrride EDID
- Set epoch counter to signal connector status change
- gud_drm_driver can be const now
v5:
- GUD_DRM_FORMAT_R1: Use non-human ascii values (Daniel)
- Change name to: GUD USB Display (Thomas, Simon)
- Change one __u32 -> __le32 in protocol header
- Always log fb flush errors, unless the previous one failed
- Run backlight update in a worker to avoid upsetting lockdep (Daniel)
- Drop backlight_ops.get_brightness, there's no readback from the device
so it doesn't really add anything.
- Set dma mask, needed by dma-buf importers
v6:
- Use obj-y in Makefile (Peter)
- Fix missing le32_to_cpu() when using GUD_DISPLAY_MAGIC (Peter)
- Set initial brightness on backlight device
v7:
- LZ4_compress_default() can return zero, check for that
- Fix memory leak in gud_pipe_check() error path (Peter)
- Improve debug and error messages (Peter)
- Don't pass length in protocol structs (Peter)
- Pass USB interface to gud_usb_control_msg() et al. (Peter)
- Improve gud_connector_fill_properties() (Peter)
- Add GUD_PIXEL_FORMAT_RGB111 (Peter)
- Remove GUD_REQ_SET_VERSION (Peter)
- Fix DRM_IOCTL_MODE_OBJ_SETPROPERTY and the rotation property
- Fix dma-buf import (Thomas)
v8:
- Forgot to filter RGB111 from reaching userspace
- Handle a device that only returns unknown device properties (Peter)
- s/GUD_PIXEL_FORMAT_RGB111/GUD_PIXEL_FORMAT_XRGB1111/ (Peter)
- Fix R1 and XRGB1111 format conversion
- Add FIXME about Big Endian being broken (Peter, Ilia)
Cc: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210313112545.37527-4-noralf@tronnes.org
2021-03-13 12:25:45 +01:00
// SPDX-License-Identifier: MIT
/*
* Copyright 2020 Noralf Trønnes
*/
# include <linux/dma-buf.h>
# include <linux/dma-mapping.h>
# include <linux/lz4.h>
# include <linux/module.h>
# include <linux/platform_device.h>
# include <linux/string_helpers.h>
# include <linux/usb.h>
# include <linux/vmalloc.h>
# include <linux/workqueue.h>
# include <drm/drm_atomic_helper.h>
2022-06-13 23:03:12 +03:00
# include <drm/drm_blend.h>
drm: Add GUD USB Display driver
This adds a USB display driver with the intention that it can be
used with future USB interfaced low end displays/adapters. The Linux
gadget device driver will serve as the canonical device implementation.
The following DRM properties are supported:
- Plane rotation
- Connector TV properties
There is also support for backlight brightness exposed as a backlight
device.
Display modes can be made available to the host driver either as DRM
display modes or through EDID. If both are present, EDID is just passed
on to userspace.
Performance is preferred over color depth, so if the device supports
RGB565, DRM_CAP_DUMB_PREFERRED_DEPTH will return 16.
If the device transfer buffer can't fit an uncompressed framebuffer
update, the update is split up into parts that do fit.
Optimal user experience is achieved by providing damage reports either by
setting FB_DAMAGE_CLIPS on pageflips or calling DRM_IOCTL_MODE_DIRTYFB.
LZ4 compression is used if the device supports it.
The driver supports a one bit monochrome transfer format: R1. This is not
implemented in the gadget driver. It is added in preparation for future
monochrome e-ink displays.
The driver is MIT licensed to smooth the path for any BSD port of the
driver.
v2:
- Use devm_drm_dev_alloc() and drmm_mode_config_init()
- drm_fbdev_generic_setup: Use preferred_bpp=0, 16 was a copy paste error
- The drm_backlight_helper is dropped, copy in the code
- Support protocol version backwards compatibility for device
v3:
- Use donated Openmoko USB pid
- Use direct compression from framebuffer when pitch matches, not only on
full frames, so split updates can benefit
- Use __le16 in struct gud_drm_req_get_connector_status
- Set edid property when the device only provides edid
- Clear compression fields in struct gud_drm_req_set_buffer
- Fix protocol version negotiation
- Remove mode->vrefresh, it's calculated
v4:
- Drop the status req polling which was a workaround for something that
turned out to be a dwc2 udc driver problem
- Add a flag for the Linux gadget to require a status request on
SET operations. Other devices will only get status req on STALL errors
- Use protocol specific error codes (Peter)
- Add a flag for devices that want to receive the entire framebuffer on
each flush (Lubomir)
- Retry a failed framebuffer flush
- If mode has changed wait for worker and clear pending damage before
queuing up new damage, fb width/height might have changed
- Increase error counter on bulk transfer failures
- Use DRM_MODE_CONNECTOR_USB
- Handle R1 kmalloc error (Peter)
- Don't try and replicate the USB get descriptor request standard for the
display descriptor (Peter)
- Make max_buffer_size optional (Peter), drop the pow2 requirement since
it's not necessary anymore.
- Don't pre-alloc a control request buffer, it was only 4k
- Let gud.h describe the whole protocol explicitly and don't let DRM
leak into it (Peter)
- Drop display mode .hskew and .vscan from the protocol
- Shorten names: s/GUD_DRM_/GUD_/ s/gud_drm_/gud_/ (Peter)
- Fix gud_pipe_check() connector picking when switching connector
- Drop gud_drm_driver_gem_create_object() cached is default now
- Retrieve USB device from struct drm_device.dev instead of keeping a
pointer
- Honour fb->offsets[0]
- Fix mode fetching when connector status is forced
- Check EDID length reported by the device
- Use drm_do_get_edid() so userspace can overrride EDID
- Set epoch counter to signal connector status change
- gud_drm_driver can be const now
v5:
- GUD_DRM_FORMAT_R1: Use non-human ascii values (Daniel)
- Change name to: GUD USB Display (Thomas, Simon)
- Change one __u32 -> __le32 in protocol header
- Always log fb flush errors, unless the previous one failed
- Run backlight update in a worker to avoid upsetting lockdep (Daniel)
- Drop backlight_ops.get_brightness, there's no readback from the device
so it doesn't really add anything.
- Set dma mask, needed by dma-buf importers
v6:
- Use obj-y in Makefile (Peter)
- Fix missing le32_to_cpu() when using GUD_DISPLAY_MAGIC (Peter)
- Set initial brightness on backlight device
v7:
- LZ4_compress_default() can return zero, check for that
- Fix memory leak in gud_pipe_check() error path (Peter)
- Improve debug and error messages (Peter)
- Don't pass length in protocol structs (Peter)
- Pass USB interface to gud_usb_control_msg() et al. (Peter)
- Improve gud_connector_fill_properties() (Peter)
- Add GUD_PIXEL_FORMAT_RGB111 (Peter)
- Remove GUD_REQ_SET_VERSION (Peter)
- Fix DRM_IOCTL_MODE_OBJ_SETPROPERTY and the rotation property
- Fix dma-buf import (Thomas)
v8:
- Forgot to filter RGB111 from reaching userspace
- Handle a device that only returns unknown device properties (Peter)
- s/GUD_PIXEL_FORMAT_RGB111/GUD_PIXEL_FORMAT_XRGB1111/ (Peter)
- Fix R1 and XRGB1111 format conversion
- Add FIXME about Big Endian being broken (Peter, Ilia)
Cc: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210313112545.37527-4-noralf@tronnes.org
2021-03-13 12:25:45 +01:00
# include <drm/drm_damage_helper.h>
# include <drm/drm_debugfs.h>
# include <drm/drm_drv.h>
2022-11-03 16:14:44 +01:00
# include <drm/drm_fbdev_generic.h>
drm: Add GUD USB Display driver
This adds a USB display driver with the intention that it can be
used with future USB interfaced low end displays/adapters. The Linux
gadget device driver will serve as the canonical device implementation.
The following DRM properties are supported:
- Plane rotation
- Connector TV properties
There is also support for backlight brightness exposed as a backlight
device.
Display modes can be made available to the host driver either as DRM
display modes or through EDID. If both are present, EDID is just passed
on to userspace.
Performance is preferred over color depth, so if the device supports
RGB565, DRM_CAP_DUMB_PREFERRED_DEPTH will return 16.
If the device transfer buffer can't fit an uncompressed framebuffer
update, the update is split up into parts that do fit.
Optimal user experience is achieved by providing damage reports either by
setting FB_DAMAGE_CLIPS on pageflips or calling DRM_IOCTL_MODE_DIRTYFB.
LZ4 compression is used if the device supports it.
The driver supports a one bit monochrome transfer format: R1. This is not
implemented in the gadget driver. It is added in preparation for future
monochrome e-ink displays.
The driver is MIT licensed to smooth the path for any BSD port of the
driver.
v2:
- Use devm_drm_dev_alloc() and drmm_mode_config_init()
- drm_fbdev_generic_setup: Use preferred_bpp=0, 16 was a copy paste error
- The drm_backlight_helper is dropped, copy in the code
- Support protocol version backwards compatibility for device
v3:
- Use donated Openmoko USB pid
- Use direct compression from framebuffer when pitch matches, not only on
full frames, so split updates can benefit
- Use __le16 in struct gud_drm_req_get_connector_status
- Set edid property when the device only provides edid
- Clear compression fields in struct gud_drm_req_set_buffer
- Fix protocol version negotiation
- Remove mode->vrefresh, it's calculated
v4:
- Drop the status req polling which was a workaround for something that
turned out to be a dwc2 udc driver problem
- Add a flag for the Linux gadget to require a status request on
SET operations. Other devices will only get status req on STALL errors
- Use protocol specific error codes (Peter)
- Add a flag for devices that want to receive the entire framebuffer on
each flush (Lubomir)
- Retry a failed framebuffer flush
- If mode has changed wait for worker and clear pending damage before
queuing up new damage, fb width/height might have changed
- Increase error counter on bulk transfer failures
- Use DRM_MODE_CONNECTOR_USB
- Handle R1 kmalloc error (Peter)
- Don't try and replicate the USB get descriptor request standard for the
display descriptor (Peter)
- Make max_buffer_size optional (Peter), drop the pow2 requirement since
it's not necessary anymore.
- Don't pre-alloc a control request buffer, it was only 4k
- Let gud.h describe the whole protocol explicitly and don't let DRM
leak into it (Peter)
- Drop display mode .hskew and .vscan from the protocol
- Shorten names: s/GUD_DRM_/GUD_/ s/gud_drm_/gud_/ (Peter)
- Fix gud_pipe_check() connector picking when switching connector
- Drop gud_drm_driver_gem_create_object() cached is default now
- Retrieve USB device from struct drm_device.dev instead of keeping a
pointer
- Honour fb->offsets[0]
- Fix mode fetching when connector status is forced
- Check EDID length reported by the device
- Use drm_do_get_edid() so userspace can overrride EDID
- Set epoch counter to signal connector status change
- gud_drm_driver can be const now
v5:
- GUD_DRM_FORMAT_R1: Use non-human ascii values (Daniel)
- Change name to: GUD USB Display (Thomas, Simon)
- Change one __u32 -> __le32 in protocol header
- Always log fb flush errors, unless the previous one failed
- Run backlight update in a worker to avoid upsetting lockdep (Daniel)
- Drop backlight_ops.get_brightness, there's no readback from the device
so it doesn't really add anything.
- Set dma mask, needed by dma-buf importers
v6:
- Use obj-y in Makefile (Peter)
- Fix missing le32_to_cpu() when using GUD_DISPLAY_MAGIC (Peter)
- Set initial brightness on backlight device
v7:
- LZ4_compress_default() can return zero, check for that
- Fix memory leak in gud_pipe_check() error path (Peter)
- Improve debug and error messages (Peter)
- Don't pass length in protocol structs (Peter)
- Pass USB interface to gud_usb_control_msg() et al. (Peter)
- Improve gud_connector_fill_properties() (Peter)
- Add GUD_PIXEL_FORMAT_RGB111 (Peter)
- Remove GUD_REQ_SET_VERSION (Peter)
- Fix DRM_IOCTL_MODE_OBJ_SETPROPERTY and the rotation property
- Fix dma-buf import (Thomas)
v8:
- Forgot to filter RGB111 from reaching userspace
- Handle a device that only returns unknown device properties (Peter)
- s/GUD_PIXEL_FORMAT_RGB111/GUD_PIXEL_FORMAT_XRGB1111/ (Peter)
- Fix R1 and XRGB1111 format conversion
- Add FIXME about Big Endian being broken (Peter, Ilia)
Cc: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210313112545.37527-4-noralf@tronnes.org
2021-03-13 12:25:45 +01:00
# include <drm/drm_fourcc.h>
# include <drm/drm_gem_atomic_helper.h>
# include <drm/drm_gem_framebuffer_helper.h>
# include <drm/drm_gem_shmem_helper.h>
# include <drm/drm_managed.h>
# include <drm/drm_print.h>
# include <drm/drm_probe_helper.h>
# include <drm/drm_simple_kms_helper.h>
# include <drm/gud.h>
# include "gud_internal.h"
/* Only used internally */
static const struct drm_format_info gud_drm_format_r1 = {
. format = GUD_DRM_FORMAT_R1 ,
. num_planes = 1 ,
. char_per_block = { 1 , 0 , 0 } ,
. block_w = { 8 , 0 , 0 } ,
. block_h = { 1 , 0 , 0 } ,
. hsub = 1 ,
. vsub = 1 ,
} ;
static const struct drm_format_info gud_drm_format_xrgb1111 = {
. format = GUD_DRM_FORMAT_XRGB1111 ,
. num_planes = 1 ,
. char_per_block = { 1 , 0 , 0 } ,
. block_w = { 2 , 0 , 0 } ,
. block_h = { 1 , 0 , 0 } ,
. hsub = 1 ,
. vsub = 1 ,
} ;
static int gud_usb_control_msg ( struct usb_interface * intf , bool in ,
u8 request , u16 value , void * buf , size_t len )
{
u8 requesttype = USB_TYPE_VENDOR | USB_RECIP_INTERFACE ;
u8 ifnum = intf - > cur_altsetting - > desc . bInterfaceNumber ;
struct usb_device * usb = interface_to_usbdev ( intf ) ;
unsigned int pipe ;
if ( len & & ! buf )
return - EINVAL ;
if ( in ) {
pipe = usb_rcvctrlpipe ( usb , 0 ) ;
requesttype | = USB_DIR_IN ;
} else {
pipe = usb_sndctrlpipe ( usb , 0 ) ;
requesttype | = USB_DIR_OUT ;
}
return usb_control_msg ( usb , pipe , request , requesttype , value ,
ifnum , buf , len , USB_CTRL_GET_TIMEOUT ) ;
}
static int gud_get_display_descriptor ( struct usb_interface * intf ,
struct gud_display_descriptor_req * desc )
{
void * buf ;
int ret ;
buf = kmalloc ( sizeof ( * desc ) , GFP_KERNEL ) ;
if ( ! buf )
return - ENOMEM ;
ret = gud_usb_control_msg ( intf , true , GUD_REQ_GET_DESCRIPTOR , 0 , buf , sizeof ( * desc ) ) ;
memcpy ( desc , buf , sizeof ( * desc ) ) ;
kfree ( buf ) ;
if ( ret < 0 )
return ret ;
if ( ret ! = sizeof ( * desc ) )
return - EIO ;
if ( desc - > magic ! = le32_to_cpu ( GUD_DISPLAY_MAGIC ) )
return - ENODATA ;
DRM_DEV_DEBUG_DRIVER ( & intf - > dev ,
" version=%u flags=0x%x compression=0x%x max_buffer_size=%u \n " ,
desc - > version , le32_to_cpu ( desc - > flags ) , desc - > compression ,
le32_to_cpu ( desc - > max_buffer_size ) ) ;
if ( ! desc - > version | | ! desc - > max_width | | ! desc - > max_height | |
le32_to_cpu ( desc - > min_width ) > le32_to_cpu ( desc - > max_width ) | |
le32_to_cpu ( desc - > min_height ) > le32_to_cpu ( desc - > max_height ) )
return - EINVAL ;
return 0 ;
}
static int gud_status_to_errno ( u8 status )
{
switch ( status ) {
case GUD_STATUS_OK :
return 0 ;
case GUD_STATUS_BUSY :
return - EBUSY ;
case GUD_STATUS_REQUEST_NOT_SUPPORTED :
return - EOPNOTSUPP ;
case GUD_STATUS_PROTOCOL_ERROR :
return - EPROTO ;
case GUD_STATUS_INVALID_PARAMETER :
return - EINVAL ;
case GUD_STATUS_ERROR :
return - EREMOTEIO ;
default :
return - EREMOTEIO ;
}
}
static int gud_usb_get_status ( struct usb_interface * intf )
{
int ret , status = - EIO ;
u8 * buf ;
buf = kmalloc ( sizeof ( * buf ) , GFP_KERNEL ) ;
if ( ! buf )
return - ENOMEM ;
ret = gud_usb_control_msg ( intf , true , GUD_REQ_GET_STATUS , 0 , buf , sizeof ( * buf ) ) ;
if ( ret = = sizeof ( * buf ) )
status = gud_status_to_errno ( * buf ) ;
kfree ( buf ) ;
if ( ret < 0 )
return ret ;
return status ;
}
static int gud_usb_transfer ( struct gud_device * gdrm , bool in , u8 request , u16 index ,
void * buf , size_t len )
{
struct usb_interface * intf = to_usb_interface ( gdrm - > drm . dev ) ;
int idx , ret ;
drm_dbg ( & gdrm - > drm , " %s: request=0x%x index=%u len=%zu \n " ,
in ? " get " : " set " , request , index , len ) ;
if ( ! drm_dev_enter ( & gdrm - > drm , & idx ) )
return - ENODEV ;
mutex_lock ( & gdrm - > ctrl_lock ) ;
ret = gud_usb_control_msg ( intf , in , request , index , buf , len ) ;
if ( ret = = - EPIPE | | ( ( gdrm - > flags & GUD_DISPLAY_FLAG_STATUS_ON_SET ) & & ! in & & ret > = 0 ) ) {
int status ;
status = gud_usb_get_status ( intf ) ;
if ( status < 0 ) {
ret = status ;
} else if ( ret < 0 ) {
dev_err_once ( gdrm - > drm . dev ,
" Unexpected status OK for failed transfer \n " ) ;
ret = - EPIPE ;
}
}
if ( ret < 0 ) {
drm_dbg ( & gdrm - > drm , " ret=%d \n " , ret ) ;
gdrm - > stats_num_errors + + ;
}
mutex_unlock ( & gdrm - > ctrl_lock ) ;
drm_dev_exit ( idx ) ;
return ret ;
}
/*
* @ buf cannot be allocated on the stack .
* Returns number of bytes received or negative error code on failure .
*/
int gud_usb_get ( struct gud_device * gdrm , u8 request , u16 index , void * buf , size_t max_len )
{
return gud_usb_transfer ( gdrm , true , request , index , buf , max_len ) ;
}
/*
* @ buf can be allocated on the stack or NULL .
* Returns zero on success or negative error code on failure .
*/
int gud_usb_set ( struct gud_device * gdrm , u8 request , u16 index , void * buf , size_t len )
{
void * trbuf = NULL ;
int ret ;
if ( buf & & len ) {
trbuf = kmemdup ( buf , len , GFP_KERNEL ) ;
if ( ! trbuf )
return - ENOMEM ;
}
ret = gud_usb_transfer ( gdrm , false , request , index , trbuf , len ) ;
kfree ( trbuf ) ;
if ( ret < 0 )
return ret ;
return ret ! = len ? - EIO : 0 ;
}
/*
* @ val can be allocated on the stack .
* Returns zero on success or negative error code on failure .
*/
int gud_usb_get_u8 ( struct gud_device * gdrm , u8 request , u16 index , u8 * val )
{
u8 * buf ;
int ret ;
buf = kmalloc ( sizeof ( * val ) , GFP_KERNEL ) ;
if ( ! buf )
return - ENOMEM ;
ret = gud_usb_get ( gdrm , request , index , buf , sizeof ( * val ) ) ;
* val = * buf ;
kfree ( buf ) ;
if ( ret < 0 )
return ret ;
return ret ! = sizeof ( * val ) ? - EIO : 0 ;
}
/* Returns zero on success or negative error code on failure. */
int gud_usb_set_u8 ( struct gud_device * gdrm , u8 request , u8 val )
{
return gud_usb_set ( gdrm , request , 0 , & val , sizeof ( val ) ) ;
}
static int gud_get_properties ( struct gud_device * gdrm )
{
struct gud_property_req * properties ;
unsigned int i , num_properties ;
int ret ;
properties = kcalloc ( GUD_PROPERTIES_MAX_NUM , sizeof ( * properties ) , GFP_KERNEL ) ;
if ( ! properties )
return - ENOMEM ;
ret = gud_usb_get ( gdrm , GUD_REQ_GET_PROPERTIES , 0 ,
properties , GUD_PROPERTIES_MAX_NUM * sizeof ( * properties ) ) ;
if ( ret < = 0 )
goto out ;
if ( ret % sizeof ( * properties ) ) {
ret = - EIO ;
goto out ;
}
num_properties = ret / sizeof ( * properties ) ;
ret = 0 ;
gdrm - > properties = drmm_kcalloc ( & gdrm - > drm , num_properties , sizeof ( * gdrm - > properties ) ,
GFP_KERNEL ) ;
if ( ! gdrm - > properties ) {
ret = - ENOMEM ;
goto out ;
}
for ( i = 0 ; i < num_properties ; i + + ) {
u16 prop = le16_to_cpu ( properties [ i ] . prop ) ;
u64 val = le64_to_cpu ( properties [ i ] . val ) ;
switch ( prop ) {
case GUD_PROPERTY_ROTATION :
/*
* DRM UAPI matches the protocol so use the value directly ,
* but mask out any additions on future devices .
*/
val & = GUD_ROTATION_MASK ;
ret = drm_plane_create_rotation_property ( & gdrm - > pipe . plane ,
DRM_MODE_ROTATE_0 , val ) ;
break ;
default :
/* New ones might show up in future devices, skip those we don't know. */
drm_dbg ( & gdrm - > drm , " Ignoring unknown property: %u \n " , prop ) ;
continue ;
}
if ( ret )
goto out ;
gdrm - > properties [ gdrm - > num_properties + + ] = prop ;
}
out :
kfree ( properties ) ;
return ret ;
}
/*
* FIXME : Dma - buf sharing requires DMA support by the importing device .
* This function is a workaround to make USB devices work as well .
* See todo . rst for how to fix the issue in the dma - buf framework .
*/
static struct drm_gem_object * gud_gem_prime_import ( struct drm_device * drm , struct dma_buf * dma_buf )
{
struct gud_device * gdrm = to_gud_device ( drm ) ;
if ( ! gdrm - > dmadev )
return ERR_PTR ( - ENODEV ) ;
return drm_gem_prime_import_dev ( drm , dma_buf , gdrm - > dmadev ) ;
}
static int gud_stats_debugfs ( struct seq_file * m , void * data )
{
2022-12-26 12:50:22 -03:00
struct drm_debugfs_entry * entry = m - > private ;
struct gud_device * gdrm = to_gud_device ( entry - > dev ) ;
drm: Add GUD USB Display driver
This adds a USB display driver with the intention that it can be
used with future USB interfaced low end displays/adapters. The Linux
gadget device driver will serve as the canonical device implementation.
The following DRM properties are supported:
- Plane rotation
- Connector TV properties
There is also support for backlight brightness exposed as a backlight
device.
Display modes can be made available to the host driver either as DRM
display modes or through EDID. If both are present, EDID is just passed
on to userspace.
Performance is preferred over color depth, so if the device supports
RGB565, DRM_CAP_DUMB_PREFERRED_DEPTH will return 16.
If the device transfer buffer can't fit an uncompressed framebuffer
update, the update is split up into parts that do fit.
Optimal user experience is achieved by providing damage reports either by
setting FB_DAMAGE_CLIPS on pageflips or calling DRM_IOCTL_MODE_DIRTYFB.
LZ4 compression is used if the device supports it.
The driver supports a one bit monochrome transfer format: R1. This is not
implemented in the gadget driver. It is added in preparation for future
monochrome e-ink displays.
The driver is MIT licensed to smooth the path for any BSD port of the
driver.
v2:
- Use devm_drm_dev_alloc() and drmm_mode_config_init()
- drm_fbdev_generic_setup: Use preferred_bpp=0, 16 was a copy paste error
- The drm_backlight_helper is dropped, copy in the code
- Support protocol version backwards compatibility for device
v3:
- Use donated Openmoko USB pid
- Use direct compression from framebuffer when pitch matches, not only on
full frames, so split updates can benefit
- Use __le16 in struct gud_drm_req_get_connector_status
- Set edid property when the device only provides edid
- Clear compression fields in struct gud_drm_req_set_buffer
- Fix protocol version negotiation
- Remove mode->vrefresh, it's calculated
v4:
- Drop the status req polling which was a workaround for something that
turned out to be a dwc2 udc driver problem
- Add a flag for the Linux gadget to require a status request on
SET operations. Other devices will only get status req on STALL errors
- Use protocol specific error codes (Peter)
- Add a flag for devices that want to receive the entire framebuffer on
each flush (Lubomir)
- Retry a failed framebuffer flush
- If mode has changed wait for worker and clear pending damage before
queuing up new damage, fb width/height might have changed
- Increase error counter on bulk transfer failures
- Use DRM_MODE_CONNECTOR_USB
- Handle R1 kmalloc error (Peter)
- Don't try and replicate the USB get descriptor request standard for the
display descriptor (Peter)
- Make max_buffer_size optional (Peter), drop the pow2 requirement since
it's not necessary anymore.
- Don't pre-alloc a control request buffer, it was only 4k
- Let gud.h describe the whole protocol explicitly and don't let DRM
leak into it (Peter)
- Drop display mode .hskew and .vscan from the protocol
- Shorten names: s/GUD_DRM_/GUD_/ s/gud_drm_/gud_/ (Peter)
- Fix gud_pipe_check() connector picking when switching connector
- Drop gud_drm_driver_gem_create_object() cached is default now
- Retrieve USB device from struct drm_device.dev instead of keeping a
pointer
- Honour fb->offsets[0]
- Fix mode fetching when connector status is forced
- Check EDID length reported by the device
- Use drm_do_get_edid() so userspace can overrride EDID
- Set epoch counter to signal connector status change
- gud_drm_driver can be const now
v5:
- GUD_DRM_FORMAT_R1: Use non-human ascii values (Daniel)
- Change name to: GUD USB Display (Thomas, Simon)
- Change one __u32 -> __le32 in protocol header
- Always log fb flush errors, unless the previous one failed
- Run backlight update in a worker to avoid upsetting lockdep (Daniel)
- Drop backlight_ops.get_brightness, there's no readback from the device
so it doesn't really add anything.
- Set dma mask, needed by dma-buf importers
v6:
- Use obj-y in Makefile (Peter)
- Fix missing le32_to_cpu() when using GUD_DISPLAY_MAGIC (Peter)
- Set initial brightness on backlight device
v7:
- LZ4_compress_default() can return zero, check for that
- Fix memory leak in gud_pipe_check() error path (Peter)
- Improve debug and error messages (Peter)
- Don't pass length in protocol structs (Peter)
- Pass USB interface to gud_usb_control_msg() et al. (Peter)
- Improve gud_connector_fill_properties() (Peter)
- Add GUD_PIXEL_FORMAT_RGB111 (Peter)
- Remove GUD_REQ_SET_VERSION (Peter)
- Fix DRM_IOCTL_MODE_OBJ_SETPROPERTY and the rotation property
- Fix dma-buf import (Thomas)
v8:
- Forgot to filter RGB111 from reaching userspace
- Handle a device that only returns unknown device properties (Peter)
- s/GUD_PIXEL_FORMAT_RGB111/GUD_PIXEL_FORMAT_XRGB1111/ (Peter)
- Fix R1 and XRGB1111 format conversion
- Add FIXME about Big Endian being broken (Peter, Ilia)
Cc: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210313112545.37527-4-noralf@tronnes.org
2021-03-13 12:25:45 +01:00
char buf [ 10 ] ;
string_get_size ( gdrm - > bulk_len , 1 , STRING_UNITS_2 , buf , sizeof ( buf ) ) ;
seq_printf ( m , " Max buffer size: %s \n " , buf ) ;
seq_printf ( m , " Number of errors: %u \n " , gdrm - > stats_num_errors ) ;
seq_puts ( m , " Compression: " ) ;
if ( gdrm - > compression & GUD_COMPRESSION_LZ4 )
seq_puts ( m , " lz4 " ) ;
if ( ! gdrm - > compression )
seq_puts ( m , " none " ) ;
seq_puts ( m , " \n " ) ;
if ( gdrm - > compression ) {
u64 remainder ;
u64 ratio = div64_u64_rem ( gdrm - > stats_length , gdrm - > stats_actual_length ,
& remainder ) ;
u64 ratio_frac = div64_u64 ( remainder * 10 , gdrm - > stats_actual_length ) ;
seq_printf ( m , " Compression ratio: %llu.%llu \n " , ratio , ratio_frac ) ;
}
return 0 ;
}
static const struct drm_simple_display_pipe_funcs gud_pipe_funcs = {
. check = gud_pipe_check ,
. update = gud_pipe_update ,
2022-11-30 20:26:53 +01:00
DRM_GEM_SIMPLE_DISPLAY_PIPE_SHADOW_PLANE_FUNCS
drm: Add GUD USB Display driver
This adds a USB display driver with the intention that it can be
used with future USB interfaced low end displays/adapters. The Linux
gadget device driver will serve as the canonical device implementation.
The following DRM properties are supported:
- Plane rotation
- Connector TV properties
There is also support for backlight brightness exposed as a backlight
device.
Display modes can be made available to the host driver either as DRM
display modes or through EDID. If both are present, EDID is just passed
on to userspace.
Performance is preferred over color depth, so if the device supports
RGB565, DRM_CAP_DUMB_PREFERRED_DEPTH will return 16.
If the device transfer buffer can't fit an uncompressed framebuffer
update, the update is split up into parts that do fit.
Optimal user experience is achieved by providing damage reports either by
setting FB_DAMAGE_CLIPS on pageflips or calling DRM_IOCTL_MODE_DIRTYFB.
LZ4 compression is used if the device supports it.
The driver supports a one bit monochrome transfer format: R1. This is not
implemented in the gadget driver. It is added in preparation for future
monochrome e-ink displays.
The driver is MIT licensed to smooth the path for any BSD port of the
driver.
v2:
- Use devm_drm_dev_alloc() and drmm_mode_config_init()
- drm_fbdev_generic_setup: Use preferred_bpp=0, 16 was a copy paste error
- The drm_backlight_helper is dropped, copy in the code
- Support protocol version backwards compatibility for device
v3:
- Use donated Openmoko USB pid
- Use direct compression from framebuffer when pitch matches, not only on
full frames, so split updates can benefit
- Use __le16 in struct gud_drm_req_get_connector_status
- Set edid property when the device only provides edid
- Clear compression fields in struct gud_drm_req_set_buffer
- Fix protocol version negotiation
- Remove mode->vrefresh, it's calculated
v4:
- Drop the status req polling which was a workaround for something that
turned out to be a dwc2 udc driver problem
- Add a flag for the Linux gadget to require a status request on
SET operations. Other devices will only get status req on STALL errors
- Use protocol specific error codes (Peter)
- Add a flag for devices that want to receive the entire framebuffer on
each flush (Lubomir)
- Retry a failed framebuffer flush
- If mode has changed wait for worker and clear pending damage before
queuing up new damage, fb width/height might have changed
- Increase error counter on bulk transfer failures
- Use DRM_MODE_CONNECTOR_USB
- Handle R1 kmalloc error (Peter)
- Don't try and replicate the USB get descriptor request standard for the
display descriptor (Peter)
- Make max_buffer_size optional (Peter), drop the pow2 requirement since
it's not necessary anymore.
- Don't pre-alloc a control request buffer, it was only 4k
- Let gud.h describe the whole protocol explicitly and don't let DRM
leak into it (Peter)
- Drop display mode .hskew and .vscan from the protocol
- Shorten names: s/GUD_DRM_/GUD_/ s/gud_drm_/gud_/ (Peter)
- Fix gud_pipe_check() connector picking when switching connector
- Drop gud_drm_driver_gem_create_object() cached is default now
- Retrieve USB device from struct drm_device.dev instead of keeping a
pointer
- Honour fb->offsets[0]
- Fix mode fetching when connector status is forced
- Check EDID length reported by the device
- Use drm_do_get_edid() so userspace can overrride EDID
- Set epoch counter to signal connector status change
- gud_drm_driver can be const now
v5:
- GUD_DRM_FORMAT_R1: Use non-human ascii values (Daniel)
- Change name to: GUD USB Display (Thomas, Simon)
- Change one __u32 -> __le32 in protocol header
- Always log fb flush errors, unless the previous one failed
- Run backlight update in a worker to avoid upsetting lockdep (Daniel)
- Drop backlight_ops.get_brightness, there's no readback from the device
so it doesn't really add anything.
- Set dma mask, needed by dma-buf importers
v6:
- Use obj-y in Makefile (Peter)
- Fix missing le32_to_cpu() when using GUD_DISPLAY_MAGIC (Peter)
- Set initial brightness on backlight device
v7:
- LZ4_compress_default() can return zero, check for that
- Fix memory leak in gud_pipe_check() error path (Peter)
- Improve debug and error messages (Peter)
- Don't pass length in protocol structs (Peter)
- Pass USB interface to gud_usb_control_msg() et al. (Peter)
- Improve gud_connector_fill_properties() (Peter)
- Add GUD_PIXEL_FORMAT_RGB111 (Peter)
- Remove GUD_REQ_SET_VERSION (Peter)
- Fix DRM_IOCTL_MODE_OBJ_SETPROPERTY and the rotation property
- Fix dma-buf import (Thomas)
v8:
- Forgot to filter RGB111 from reaching userspace
- Handle a device that only returns unknown device properties (Peter)
- s/GUD_PIXEL_FORMAT_RGB111/GUD_PIXEL_FORMAT_XRGB1111/ (Peter)
- Fix R1 and XRGB1111 format conversion
- Add FIXME about Big Endian being broken (Peter, Ilia)
Cc: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210313112545.37527-4-noralf@tronnes.org
2021-03-13 12:25:45 +01:00
} ;
static const struct drm_mode_config_funcs gud_mode_config_funcs = {
. fb_create = drm_gem_fb_create_with_dirty ,
. atomic_check = drm_atomic_helper_check ,
. atomic_commit = drm_atomic_helper_commit ,
} ;
static const u64 gud_pipe_modifiers [ ] = {
DRM_FORMAT_MOD_LINEAR ,
DRM_FORMAT_MOD_INVALID
} ;
DEFINE_DRM_GEM_FOPS ( gud_fops ) ;
static const struct drm_driver gud_drm_driver = {
. driver_features = DRIVER_MODESET | DRIVER_GEM | DRIVER_ATOMIC ,
. fops = & gud_fops ,
DRM_GEM_SHMEM_DRIVER_OPS ,
. gem_prime_import = gud_gem_prime_import ,
. name = " gud " ,
. desc = " Generic USB Display " ,
. date = " 20200422 " ,
. major = 1 ,
. minor = 0 ,
} ;
2021-07-01 19:07:48 +02:00
static int gud_alloc_bulk_buffer ( struct gud_device * gdrm )
{
unsigned int i , num_pages ;
struct page * * pages ;
void * ptr ;
int ret ;
gdrm - > bulk_buf = vmalloc_32 ( gdrm - > bulk_len ) ;
if ( ! gdrm - > bulk_buf )
return - ENOMEM ;
num_pages = DIV_ROUND_UP ( gdrm - > bulk_len , PAGE_SIZE ) ;
pages = kmalloc_array ( num_pages , sizeof ( struct page * ) , GFP_KERNEL ) ;
if ( ! pages )
return - ENOMEM ;
for ( i = 0 , ptr = gdrm - > bulk_buf ; i < num_pages ; i + + , ptr + = PAGE_SIZE )
pages [ i ] = vmalloc_to_page ( ptr ) ;
ret = sg_alloc_table_from_pages ( & gdrm - > bulk_sgt , pages , num_pages ,
0 , gdrm - > bulk_len , GFP_KERNEL ) ;
kfree ( pages ) ;
return ret ;
}
2021-07-01 19:07:47 +02:00
static void gud_free_buffers_and_mutex ( void * data )
drm: Add GUD USB Display driver
This adds a USB display driver with the intention that it can be
used with future USB interfaced low end displays/adapters. The Linux
gadget device driver will serve as the canonical device implementation.
The following DRM properties are supported:
- Plane rotation
- Connector TV properties
There is also support for backlight brightness exposed as a backlight
device.
Display modes can be made available to the host driver either as DRM
display modes or through EDID. If both are present, EDID is just passed
on to userspace.
Performance is preferred over color depth, so if the device supports
RGB565, DRM_CAP_DUMB_PREFERRED_DEPTH will return 16.
If the device transfer buffer can't fit an uncompressed framebuffer
update, the update is split up into parts that do fit.
Optimal user experience is achieved by providing damage reports either by
setting FB_DAMAGE_CLIPS on pageflips or calling DRM_IOCTL_MODE_DIRTYFB.
LZ4 compression is used if the device supports it.
The driver supports a one bit monochrome transfer format: R1. This is not
implemented in the gadget driver. It is added in preparation for future
monochrome e-ink displays.
The driver is MIT licensed to smooth the path for any BSD port of the
driver.
v2:
- Use devm_drm_dev_alloc() and drmm_mode_config_init()
- drm_fbdev_generic_setup: Use preferred_bpp=0, 16 was a copy paste error
- The drm_backlight_helper is dropped, copy in the code
- Support protocol version backwards compatibility for device
v3:
- Use donated Openmoko USB pid
- Use direct compression from framebuffer when pitch matches, not only on
full frames, so split updates can benefit
- Use __le16 in struct gud_drm_req_get_connector_status
- Set edid property when the device only provides edid
- Clear compression fields in struct gud_drm_req_set_buffer
- Fix protocol version negotiation
- Remove mode->vrefresh, it's calculated
v4:
- Drop the status req polling which was a workaround for something that
turned out to be a dwc2 udc driver problem
- Add a flag for the Linux gadget to require a status request on
SET operations. Other devices will only get status req on STALL errors
- Use protocol specific error codes (Peter)
- Add a flag for devices that want to receive the entire framebuffer on
each flush (Lubomir)
- Retry a failed framebuffer flush
- If mode has changed wait for worker and clear pending damage before
queuing up new damage, fb width/height might have changed
- Increase error counter on bulk transfer failures
- Use DRM_MODE_CONNECTOR_USB
- Handle R1 kmalloc error (Peter)
- Don't try and replicate the USB get descriptor request standard for the
display descriptor (Peter)
- Make max_buffer_size optional (Peter), drop the pow2 requirement since
it's not necessary anymore.
- Don't pre-alloc a control request buffer, it was only 4k
- Let gud.h describe the whole protocol explicitly and don't let DRM
leak into it (Peter)
- Drop display mode .hskew and .vscan from the protocol
- Shorten names: s/GUD_DRM_/GUD_/ s/gud_drm_/gud_/ (Peter)
- Fix gud_pipe_check() connector picking when switching connector
- Drop gud_drm_driver_gem_create_object() cached is default now
- Retrieve USB device from struct drm_device.dev instead of keeping a
pointer
- Honour fb->offsets[0]
- Fix mode fetching when connector status is forced
- Check EDID length reported by the device
- Use drm_do_get_edid() so userspace can overrride EDID
- Set epoch counter to signal connector status change
- gud_drm_driver can be const now
v5:
- GUD_DRM_FORMAT_R1: Use non-human ascii values (Daniel)
- Change name to: GUD USB Display (Thomas, Simon)
- Change one __u32 -> __le32 in protocol header
- Always log fb flush errors, unless the previous one failed
- Run backlight update in a worker to avoid upsetting lockdep (Daniel)
- Drop backlight_ops.get_brightness, there's no readback from the device
so it doesn't really add anything.
- Set dma mask, needed by dma-buf importers
v6:
- Use obj-y in Makefile (Peter)
- Fix missing le32_to_cpu() when using GUD_DISPLAY_MAGIC (Peter)
- Set initial brightness on backlight device
v7:
- LZ4_compress_default() can return zero, check for that
- Fix memory leak in gud_pipe_check() error path (Peter)
- Improve debug and error messages (Peter)
- Don't pass length in protocol structs (Peter)
- Pass USB interface to gud_usb_control_msg() et al. (Peter)
- Improve gud_connector_fill_properties() (Peter)
- Add GUD_PIXEL_FORMAT_RGB111 (Peter)
- Remove GUD_REQ_SET_VERSION (Peter)
- Fix DRM_IOCTL_MODE_OBJ_SETPROPERTY and the rotation property
- Fix dma-buf import (Thomas)
v8:
- Forgot to filter RGB111 from reaching userspace
- Handle a device that only returns unknown device properties (Peter)
- s/GUD_PIXEL_FORMAT_RGB111/GUD_PIXEL_FORMAT_XRGB1111/ (Peter)
- Fix R1 and XRGB1111 format conversion
- Add FIXME about Big Endian being broken (Peter, Ilia)
Cc: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210313112545.37527-4-noralf@tronnes.org
2021-03-13 12:25:45 +01:00
{
2021-07-01 19:07:47 +02:00
struct gud_device * gdrm = data ;
drm: Add GUD USB Display driver
This adds a USB display driver with the intention that it can be
used with future USB interfaced low end displays/adapters. The Linux
gadget device driver will serve as the canonical device implementation.
The following DRM properties are supported:
- Plane rotation
- Connector TV properties
There is also support for backlight brightness exposed as a backlight
device.
Display modes can be made available to the host driver either as DRM
display modes or through EDID. If both are present, EDID is just passed
on to userspace.
Performance is preferred over color depth, so if the device supports
RGB565, DRM_CAP_DUMB_PREFERRED_DEPTH will return 16.
If the device transfer buffer can't fit an uncompressed framebuffer
update, the update is split up into parts that do fit.
Optimal user experience is achieved by providing damage reports either by
setting FB_DAMAGE_CLIPS on pageflips or calling DRM_IOCTL_MODE_DIRTYFB.
LZ4 compression is used if the device supports it.
The driver supports a one bit monochrome transfer format: R1. This is not
implemented in the gadget driver. It is added in preparation for future
monochrome e-ink displays.
The driver is MIT licensed to smooth the path for any BSD port of the
driver.
v2:
- Use devm_drm_dev_alloc() and drmm_mode_config_init()
- drm_fbdev_generic_setup: Use preferred_bpp=0, 16 was a copy paste error
- The drm_backlight_helper is dropped, copy in the code
- Support protocol version backwards compatibility for device
v3:
- Use donated Openmoko USB pid
- Use direct compression from framebuffer when pitch matches, not only on
full frames, so split updates can benefit
- Use __le16 in struct gud_drm_req_get_connector_status
- Set edid property when the device only provides edid
- Clear compression fields in struct gud_drm_req_set_buffer
- Fix protocol version negotiation
- Remove mode->vrefresh, it's calculated
v4:
- Drop the status req polling which was a workaround for something that
turned out to be a dwc2 udc driver problem
- Add a flag for the Linux gadget to require a status request on
SET operations. Other devices will only get status req on STALL errors
- Use protocol specific error codes (Peter)
- Add a flag for devices that want to receive the entire framebuffer on
each flush (Lubomir)
- Retry a failed framebuffer flush
- If mode has changed wait for worker and clear pending damage before
queuing up new damage, fb width/height might have changed
- Increase error counter on bulk transfer failures
- Use DRM_MODE_CONNECTOR_USB
- Handle R1 kmalloc error (Peter)
- Don't try and replicate the USB get descriptor request standard for the
display descriptor (Peter)
- Make max_buffer_size optional (Peter), drop the pow2 requirement since
it's not necessary anymore.
- Don't pre-alloc a control request buffer, it was only 4k
- Let gud.h describe the whole protocol explicitly and don't let DRM
leak into it (Peter)
- Drop display mode .hskew and .vscan from the protocol
- Shorten names: s/GUD_DRM_/GUD_/ s/gud_drm_/gud_/ (Peter)
- Fix gud_pipe_check() connector picking when switching connector
- Drop gud_drm_driver_gem_create_object() cached is default now
- Retrieve USB device from struct drm_device.dev instead of keeping a
pointer
- Honour fb->offsets[0]
- Fix mode fetching when connector status is forced
- Check EDID length reported by the device
- Use drm_do_get_edid() so userspace can overrride EDID
- Set epoch counter to signal connector status change
- gud_drm_driver can be const now
v5:
- GUD_DRM_FORMAT_R1: Use non-human ascii values (Daniel)
- Change name to: GUD USB Display (Thomas, Simon)
- Change one __u32 -> __le32 in protocol header
- Always log fb flush errors, unless the previous one failed
- Run backlight update in a worker to avoid upsetting lockdep (Daniel)
- Drop backlight_ops.get_brightness, there's no readback from the device
so it doesn't really add anything.
- Set dma mask, needed by dma-buf importers
v6:
- Use obj-y in Makefile (Peter)
- Fix missing le32_to_cpu() when using GUD_DISPLAY_MAGIC (Peter)
- Set initial brightness on backlight device
v7:
- LZ4_compress_default() can return zero, check for that
- Fix memory leak in gud_pipe_check() error path (Peter)
- Improve debug and error messages (Peter)
- Don't pass length in protocol structs (Peter)
- Pass USB interface to gud_usb_control_msg() et al. (Peter)
- Improve gud_connector_fill_properties() (Peter)
- Add GUD_PIXEL_FORMAT_RGB111 (Peter)
- Remove GUD_REQ_SET_VERSION (Peter)
- Fix DRM_IOCTL_MODE_OBJ_SETPROPERTY and the rotation property
- Fix dma-buf import (Thomas)
v8:
- Forgot to filter RGB111 from reaching userspace
- Handle a device that only returns unknown device properties (Peter)
- s/GUD_PIXEL_FORMAT_RGB111/GUD_PIXEL_FORMAT_XRGB1111/ (Peter)
- Fix R1 and XRGB1111 format conversion
- Add FIXME about Big Endian being broken (Peter, Ilia)
Cc: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210313112545.37527-4-noralf@tronnes.org
2021-03-13 12:25:45 +01:00
vfree ( gdrm - > compress_buf ) ;
2021-07-01 19:07:47 +02:00
gdrm - > compress_buf = NULL ;
2021-07-01 19:07:48 +02:00
sg_free_table ( & gdrm - > bulk_sgt ) ;
vfree ( gdrm - > bulk_buf ) ;
2021-07-01 19:07:47 +02:00
gdrm - > bulk_buf = NULL ;
drm: Add GUD USB Display driver
This adds a USB display driver with the intention that it can be
used with future USB interfaced low end displays/adapters. The Linux
gadget device driver will serve as the canonical device implementation.
The following DRM properties are supported:
- Plane rotation
- Connector TV properties
There is also support for backlight brightness exposed as a backlight
device.
Display modes can be made available to the host driver either as DRM
display modes or through EDID. If both are present, EDID is just passed
on to userspace.
Performance is preferred over color depth, so if the device supports
RGB565, DRM_CAP_DUMB_PREFERRED_DEPTH will return 16.
If the device transfer buffer can't fit an uncompressed framebuffer
update, the update is split up into parts that do fit.
Optimal user experience is achieved by providing damage reports either by
setting FB_DAMAGE_CLIPS on pageflips or calling DRM_IOCTL_MODE_DIRTYFB.
LZ4 compression is used if the device supports it.
The driver supports a one bit monochrome transfer format: R1. This is not
implemented in the gadget driver. It is added in preparation for future
monochrome e-ink displays.
The driver is MIT licensed to smooth the path for any BSD port of the
driver.
v2:
- Use devm_drm_dev_alloc() and drmm_mode_config_init()
- drm_fbdev_generic_setup: Use preferred_bpp=0, 16 was a copy paste error
- The drm_backlight_helper is dropped, copy in the code
- Support protocol version backwards compatibility for device
v3:
- Use donated Openmoko USB pid
- Use direct compression from framebuffer when pitch matches, not only on
full frames, so split updates can benefit
- Use __le16 in struct gud_drm_req_get_connector_status
- Set edid property when the device only provides edid
- Clear compression fields in struct gud_drm_req_set_buffer
- Fix protocol version negotiation
- Remove mode->vrefresh, it's calculated
v4:
- Drop the status req polling which was a workaround for something that
turned out to be a dwc2 udc driver problem
- Add a flag for the Linux gadget to require a status request on
SET operations. Other devices will only get status req on STALL errors
- Use protocol specific error codes (Peter)
- Add a flag for devices that want to receive the entire framebuffer on
each flush (Lubomir)
- Retry a failed framebuffer flush
- If mode has changed wait for worker and clear pending damage before
queuing up new damage, fb width/height might have changed
- Increase error counter on bulk transfer failures
- Use DRM_MODE_CONNECTOR_USB
- Handle R1 kmalloc error (Peter)
- Don't try and replicate the USB get descriptor request standard for the
display descriptor (Peter)
- Make max_buffer_size optional (Peter), drop the pow2 requirement since
it's not necessary anymore.
- Don't pre-alloc a control request buffer, it was only 4k
- Let gud.h describe the whole protocol explicitly and don't let DRM
leak into it (Peter)
- Drop display mode .hskew and .vscan from the protocol
- Shorten names: s/GUD_DRM_/GUD_/ s/gud_drm_/gud_/ (Peter)
- Fix gud_pipe_check() connector picking when switching connector
- Drop gud_drm_driver_gem_create_object() cached is default now
- Retrieve USB device from struct drm_device.dev instead of keeping a
pointer
- Honour fb->offsets[0]
- Fix mode fetching when connector status is forced
- Check EDID length reported by the device
- Use drm_do_get_edid() so userspace can overrride EDID
- Set epoch counter to signal connector status change
- gud_drm_driver can be const now
v5:
- GUD_DRM_FORMAT_R1: Use non-human ascii values (Daniel)
- Change name to: GUD USB Display (Thomas, Simon)
- Change one __u32 -> __le32 in protocol header
- Always log fb flush errors, unless the previous one failed
- Run backlight update in a worker to avoid upsetting lockdep (Daniel)
- Drop backlight_ops.get_brightness, there's no readback from the device
so it doesn't really add anything.
- Set dma mask, needed by dma-buf importers
v6:
- Use obj-y in Makefile (Peter)
- Fix missing le32_to_cpu() when using GUD_DISPLAY_MAGIC (Peter)
- Set initial brightness on backlight device
v7:
- LZ4_compress_default() can return zero, check for that
- Fix memory leak in gud_pipe_check() error path (Peter)
- Improve debug and error messages (Peter)
- Don't pass length in protocol structs (Peter)
- Pass USB interface to gud_usb_control_msg() et al. (Peter)
- Improve gud_connector_fill_properties() (Peter)
- Add GUD_PIXEL_FORMAT_RGB111 (Peter)
- Remove GUD_REQ_SET_VERSION (Peter)
- Fix DRM_IOCTL_MODE_OBJ_SETPROPERTY and the rotation property
- Fix dma-buf import (Thomas)
v8:
- Forgot to filter RGB111 from reaching userspace
- Handle a device that only returns unknown device properties (Peter)
- s/GUD_PIXEL_FORMAT_RGB111/GUD_PIXEL_FORMAT_XRGB1111/ (Peter)
- Fix R1 and XRGB1111 format conversion
- Add FIXME about Big Endian being broken (Peter, Ilia)
Cc: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210313112545.37527-4-noralf@tronnes.org
2021-03-13 12:25:45 +01:00
mutex_destroy ( & gdrm - > ctrl_lock ) ;
}
static int gud_probe ( struct usb_interface * intf , const struct usb_device_id * id )
{
const struct drm_format_info * xrgb8888_emulation_format = NULL ;
bool rgb565_supported = false , xrgb8888_supported = false ;
unsigned int num_formats_dev , num_formats = 0 ;
struct usb_endpoint_descriptor * bulk_out ;
struct gud_display_descriptor_req desc ;
struct device * dev = & intf - > dev ;
size_t max_buffer_size = 0 ;
struct gud_device * gdrm ;
struct drm_device * drm ;
u8 * formats_dev ;
u32 * formats ;
int ret , i ;
ret = usb_find_bulk_out_endpoint ( intf - > cur_altsetting , & bulk_out ) ;
if ( ret )
return ret ;
ret = gud_get_display_descriptor ( intf , & desc ) ;
if ( ret ) {
DRM_DEV_DEBUG_DRIVER ( dev , " Not a display interface: ret=%d \n " , ret ) ;
return - ENODEV ;
}
if ( desc . version > 1 ) {
dev_err ( dev , " Protocol version %u is not supported \n " , desc . version ) ;
return - ENODEV ;
}
gdrm = devm_drm_dev_alloc ( dev , & gud_drm_driver , struct gud_device , drm ) ;
if ( IS_ERR ( gdrm ) )
return PTR_ERR ( gdrm ) ;
drm = & gdrm - > drm ;
drm - > mode_config . funcs = & gud_mode_config_funcs ;
ret = drmm_mode_config_init ( drm ) ;
if ( ret )
return ret ;
gdrm - > flags = le32_to_cpu ( desc . flags ) ;
gdrm - > compression = desc . compression & GUD_COMPRESSION_LZ4 ;
if ( gdrm - > flags & GUD_DISPLAY_FLAG_FULL_UPDATE & & gdrm - > compression )
return - EINVAL ;
mutex_init ( & gdrm - > ctrl_lock ) ;
mutex_init ( & gdrm - > damage_lock ) ;
INIT_WORK ( & gdrm - > work , gud_flush_work ) ;
gud_clear_damage ( gdrm ) ;
2021-07-01 19:07:47 +02:00
ret = devm_add_action ( dev , gud_free_buffers_and_mutex , gdrm ) ;
drm: Add GUD USB Display driver
This adds a USB display driver with the intention that it can be
used with future USB interfaced low end displays/adapters. The Linux
gadget device driver will serve as the canonical device implementation.
The following DRM properties are supported:
- Plane rotation
- Connector TV properties
There is also support for backlight brightness exposed as a backlight
device.
Display modes can be made available to the host driver either as DRM
display modes or through EDID. If both are present, EDID is just passed
on to userspace.
Performance is preferred over color depth, so if the device supports
RGB565, DRM_CAP_DUMB_PREFERRED_DEPTH will return 16.
If the device transfer buffer can't fit an uncompressed framebuffer
update, the update is split up into parts that do fit.
Optimal user experience is achieved by providing damage reports either by
setting FB_DAMAGE_CLIPS on pageflips or calling DRM_IOCTL_MODE_DIRTYFB.
LZ4 compression is used if the device supports it.
The driver supports a one bit monochrome transfer format: R1. This is not
implemented in the gadget driver. It is added in preparation for future
monochrome e-ink displays.
The driver is MIT licensed to smooth the path for any BSD port of the
driver.
v2:
- Use devm_drm_dev_alloc() and drmm_mode_config_init()
- drm_fbdev_generic_setup: Use preferred_bpp=0, 16 was a copy paste error
- The drm_backlight_helper is dropped, copy in the code
- Support protocol version backwards compatibility for device
v3:
- Use donated Openmoko USB pid
- Use direct compression from framebuffer when pitch matches, not only on
full frames, so split updates can benefit
- Use __le16 in struct gud_drm_req_get_connector_status
- Set edid property when the device only provides edid
- Clear compression fields in struct gud_drm_req_set_buffer
- Fix protocol version negotiation
- Remove mode->vrefresh, it's calculated
v4:
- Drop the status req polling which was a workaround for something that
turned out to be a dwc2 udc driver problem
- Add a flag for the Linux gadget to require a status request on
SET operations. Other devices will only get status req on STALL errors
- Use protocol specific error codes (Peter)
- Add a flag for devices that want to receive the entire framebuffer on
each flush (Lubomir)
- Retry a failed framebuffer flush
- If mode has changed wait for worker and clear pending damage before
queuing up new damage, fb width/height might have changed
- Increase error counter on bulk transfer failures
- Use DRM_MODE_CONNECTOR_USB
- Handle R1 kmalloc error (Peter)
- Don't try and replicate the USB get descriptor request standard for the
display descriptor (Peter)
- Make max_buffer_size optional (Peter), drop the pow2 requirement since
it's not necessary anymore.
- Don't pre-alloc a control request buffer, it was only 4k
- Let gud.h describe the whole protocol explicitly and don't let DRM
leak into it (Peter)
- Drop display mode .hskew and .vscan from the protocol
- Shorten names: s/GUD_DRM_/GUD_/ s/gud_drm_/gud_/ (Peter)
- Fix gud_pipe_check() connector picking when switching connector
- Drop gud_drm_driver_gem_create_object() cached is default now
- Retrieve USB device from struct drm_device.dev instead of keeping a
pointer
- Honour fb->offsets[0]
- Fix mode fetching when connector status is forced
- Check EDID length reported by the device
- Use drm_do_get_edid() so userspace can overrride EDID
- Set epoch counter to signal connector status change
- gud_drm_driver can be const now
v5:
- GUD_DRM_FORMAT_R1: Use non-human ascii values (Daniel)
- Change name to: GUD USB Display (Thomas, Simon)
- Change one __u32 -> __le32 in protocol header
- Always log fb flush errors, unless the previous one failed
- Run backlight update in a worker to avoid upsetting lockdep (Daniel)
- Drop backlight_ops.get_brightness, there's no readback from the device
so it doesn't really add anything.
- Set dma mask, needed by dma-buf importers
v6:
- Use obj-y in Makefile (Peter)
- Fix missing le32_to_cpu() when using GUD_DISPLAY_MAGIC (Peter)
- Set initial brightness on backlight device
v7:
- LZ4_compress_default() can return zero, check for that
- Fix memory leak in gud_pipe_check() error path (Peter)
- Improve debug and error messages (Peter)
- Don't pass length in protocol structs (Peter)
- Pass USB interface to gud_usb_control_msg() et al. (Peter)
- Improve gud_connector_fill_properties() (Peter)
- Add GUD_PIXEL_FORMAT_RGB111 (Peter)
- Remove GUD_REQ_SET_VERSION (Peter)
- Fix DRM_IOCTL_MODE_OBJ_SETPROPERTY and the rotation property
- Fix dma-buf import (Thomas)
v8:
- Forgot to filter RGB111 from reaching userspace
- Handle a device that only returns unknown device properties (Peter)
- s/GUD_PIXEL_FORMAT_RGB111/GUD_PIXEL_FORMAT_XRGB1111/ (Peter)
- Fix R1 and XRGB1111 format conversion
- Add FIXME about Big Endian being broken (Peter, Ilia)
Cc: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210313112545.37527-4-noralf@tronnes.org
2021-03-13 12:25:45 +01:00
if ( ret )
return ret ;
drm - > mode_config . min_width = le32_to_cpu ( desc . min_width ) ;
drm - > mode_config . max_width = le32_to_cpu ( desc . max_width ) ;
drm - > mode_config . min_height = le32_to_cpu ( desc . min_height ) ;
drm - > mode_config . max_height = le32_to_cpu ( desc . max_height ) ;
formats_dev = devm_kmalloc ( dev , GUD_FORMATS_MAX_NUM , GFP_KERNEL ) ;
/* Add room for emulated XRGB8888 */
formats = devm_kmalloc_array ( dev , GUD_FORMATS_MAX_NUM + 1 , sizeof ( * formats ) , GFP_KERNEL ) ;
if ( ! formats_dev | | ! formats )
return - ENOMEM ;
ret = gud_usb_get ( gdrm , GUD_REQ_GET_FORMATS , 0 , formats_dev , GUD_FORMATS_MAX_NUM ) ;
if ( ret < 0 )
return ret ;
num_formats_dev = ret ;
for ( i = 0 ; i < num_formats_dev ; i + + ) {
const struct drm_format_info * info ;
size_t fmt_buf_size ;
u32 format ;
format = gud_to_fourcc ( formats_dev [ i ] ) ;
if ( ! format ) {
drm_dbg ( drm , " Unsupported format: 0x%02x \n " , formats_dev [ i ] ) ;
continue ;
}
if ( format = = GUD_DRM_FORMAT_R1 )
info = & gud_drm_format_r1 ;
else if ( format = = GUD_DRM_FORMAT_XRGB1111 )
info = & gud_drm_format_xrgb1111 ;
else
info = drm_format_info ( format ) ;
switch ( format ) {
case GUD_DRM_FORMAT_R1 :
fallthrough ;
2021-09-29 21:11:59 +02:00
case DRM_FORMAT_R8 :
fallthrough ;
drm: Add GUD USB Display driver
This adds a USB display driver with the intention that it can be
used with future USB interfaced low end displays/adapters. The Linux
gadget device driver will serve as the canonical device implementation.
The following DRM properties are supported:
- Plane rotation
- Connector TV properties
There is also support for backlight brightness exposed as a backlight
device.
Display modes can be made available to the host driver either as DRM
display modes or through EDID. If both are present, EDID is just passed
on to userspace.
Performance is preferred over color depth, so if the device supports
RGB565, DRM_CAP_DUMB_PREFERRED_DEPTH will return 16.
If the device transfer buffer can't fit an uncompressed framebuffer
update, the update is split up into parts that do fit.
Optimal user experience is achieved by providing damage reports either by
setting FB_DAMAGE_CLIPS on pageflips or calling DRM_IOCTL_MODE_DIRTYFB.
LZ4 compression is used if the device supports it.
The driver supports a one bit monochrome transfer format: R1. This is not
implemented in the gadget driver. It is added in preparation for future
monochrome e-ink displays.
The driver is MIT licensed to smooth the path for any BSD port of the
driver.
v2:
- Use devm_drm_dev_alloc() and drmm_mode_config_init()
- drm_fbdev_generic_setup: Use preferred_bpp=0, 16 was a copy paste error
- The drm_backlight_helper is dropped, copy in the code
- Support protocol version backwards compatibility for device
v3:
- Use donated Openmoko USB pid
- Use direct compression from framebuffer when pitch matches, not only on
full frames, so split updates can benefit
- Use __le16 in struct gud_drm_req_get_connector_status
- Set edid property when the device only provides edid
- Clear compression fields in struct gud_drm_req_set_buffer
- Fix protocol version negotiation
- Remove mode->vrefresh, it's calculated
v4:
- Drop the status req polling which was a workaround for something that
turned out to be a dwc2 udc driver problem
- Add a flag for the Linux gadget to require a status request on
SET operations. Other devices will only get status req on STALL errors
- Use protocol specific error codes (Peter)
- Add a flag for devices that want to receive the entire framebuffer on
each flush (Lubomir)
- Retry a failed framebuffer flush
- If mode has changed wait for worker and clear pending damage before
queuing up new damage, fb width/height might have changed
- Increase error counter on bulk transfer failures
- Use DRM_MODE_CONNECTOR_USB
- Handle R1 kmalloc error (Peter)
- Don't try and replicate the USB get descriptor request standard for the
display descriptor (Peter)
- Make max_buffer_size optional (Peter), drop the pow2 requirement since
it's not necessary anymore.
- Don't pre-alloc a control request buffer, it was only 4k
- Let gud.h describe the whole protocol explicitly and don't let DRM
leak into it (Peter)
- Drop display mode .hskew and .vscan from the protocol
- Shorten names: s/GUD_DRM_/GUD_/ s/gud_drm_/gud_/ (Peter)
- Fix gud_pipe_check() connector picking when switching connector
- Drop gud_drm_driver_gem_create_object() cached is default now
- Retrieve USB device from struct drm_device.dev instead of keeping a
pointer
- Honour fb->offsets[0]
- Fix mode fetching when connector status is forced
- Check EDID length reported by the device
- Use drm_do_get_edid() so userspace can overrride EDID
- Set epoch counter to signal connector status change
- gud_drm_driver can be const now
v5:
- GUD_DRM_FORMAT_R1: Use non-human ascii values (Daniel)
- Change name to: GUD USB Display (Thomas, Simon)
- Change one __u32 -> __le32 in protocol header
- Always log fb flush errors, unless the previous one failed
- Run backlight update in a worker to avoid upsetting lockdep (Daniel)
- Drop backlight_ops.get_brightness, there's no readback from the device
so it doesn't really add anything.
- Set dma mask, needed by dma-buf importers
v6:
- Use obj-y in Makefile (Peter)
- Fix missing le32_to_cpu() when using GUD_DISPLAY_MAGIC (Peter)
- Set initial brightness on backlight device
v7:
- LZ4_compress_default() can return zero, check for that
- Fix memory leak in gud_pipe_check() error path (Peter)
- Improve debug and error messages (Peter)
- Don't pass length in protocol structs (Peter)
- Pass USB interface to gud_usb_control_msg() et al. (Peter)
- Improve gud_connector_fill_properties() (Peter)
- Add GUD_PIXEL_FORMAT_RGB111 (Peter)
- Remove GUD_REQ_SET_VERSION (Peter)
- Fix DRM_IOCTL_MODE_OBJ_SETPROPERTY and the rotation property
- Fix dma-buf import (Thomas)
v8:
- Forgot to filter RGB111 from reaching userspace
- Handle a device that only returns unknown device properties (Peter)
- s/GUD_PIXEL_FORMAT_RGB111/GUD_PIXEL_FORMAT_XRGB1111/ (Peter)
- Fix R1 and XRGB1111 format conversion
- Add FIXME about Big Endian being broken (Peter, Ilia)
Cc: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210313112545.37527-4-noralf@tronnes.org
2021-03-13 12:25:45 +01:00
case GUD_DRM_FORMAT_XRGB1111 :
2021-09-29 21:12:00 +02:00
fallthrough ;
case DRM_FORMAT_RGB332 :
2021-09-29 21:12:01 +02:00
fallthrough ;
case DRM_FORMAT_RGB888 :
drm: Add GUD USB Display driver
This adds a USB display driver with the intention that it can be
used with future USB interfaced low end displays/adapters. The Linux
gadget device driver will serve as the canonical device implementation.
The following DRM properties are supported:
- Plane rotation
- Connector TV properties
There is also support for backlight brightness exposed as a backlight
device.
Display modes can be made available to the host driver either as DRM
display modes or through EDID. If both are present, EDID is just passed
on to userspace.
Performance is preferred over color depth, so if the device supports
RGB565, DRM_CAP_DUMB_PREFERRED_DEPTH will return 16.
If the device transfer buffer can't fit an uncompressed framebuffer
update, the update is split up into parts that do fit.
Optimal user experience is achieved by providing damage reports either by
setting FB_DAMAGE_CLIPS on pageflips or calling DRM_IOCTL_MODE_DIRTYFB.
LZ4 compression is used if the device supports it.
The driver supports a one bit monochrome transfer format: R1. This is not
implemented in the gadget driver. It is added in preparation for future
monochrome e-ink displays.
The driver is MIT licensed to smooth the path for any BSD port of the
driver.
v2:
- Use devm_drm_dev_alloc() and drmm_mode_config_init()
- drm_fbdev_generic_setup: Use preferred_bpp=0, 16 was a copy paste error
- The drm_backlight_helper is dropped, copy in the code
- Support protocol version backwards compatibility for device
v3:
- Use donated Openmoko USB pid
- Use direct compression from framebuffer when pitch matches, not only on
full frames, so split updates can benefit
- Use __le16 in struct gud_drm_req_get_connector_status
- Set edid property when the device only provides edid
- Clear compression fields in struct gud_drm_req_set_buffer
- Fix protocol version negotiation
- Remove mode->vrefresh, it's calculated
v4:
- Drop the status req polling which was a workaround for something that
turned out to be a dwc2 udc driver problem
- Add a flag for the Linux gadget to require a status request on
SET operations. Other devices will only get status req on STALL errors
- Use protocol specific error codes (Peter)
- Add a flag for devices that want to receive the entire framebuffer on
each flush (Lubomir)
- Retry a failed framebuffer flush
- If mode has changed wait for worker and clear pending damage before
queuing up new damage, fb width/height might have changed
- Increase error counter on bulk transfer failures
- Use DRM_MODE_CONNECTOR_USB
- Handle R1 kmalloc error (Peter)
- Don't try and replicate the USB get descriptor request standard for the
display descriptor (Peter)
- Make max_buffer_size optional (Peter), drop the pow2 requirement since
it's not necessary anymore.
- Don't pre-alloc a control request buffer, it was only 4k
- Let gud.h describe the whole protocol explicitly and don't let DRM
leak into it (Peter)
- Drop display mode .hskew and .vscan from the protocol
- Shorten names: s/GUD_DRM_/GUD_/ s/gud_drm_/gud_/ (Peter)
- Fix gud_pipe_check() connector picking when switching connector
- Drop gud_drm_driver_gem_create_object() cached is default now
- Retrieve USB device from struct drm_device.dev instead of keeping a
pointer
- Honour fb->offsets[0]
- Fix mode fetching when connector status is forced
- Check EDID length reported by the device
- Use drm_do_get_edid() so userspace can overrride EDID
- Set epoch counter to signal connector status change
- gud_drm_driver can be const now
v5:
- GUD_DRM_FORMAT_R1: Use non-human ascii values (Daniel)
- Change name to: GUD USB Display (Thomas, Simon)
- Change one __u32 -> __le32 in protocol header
- Always log fb flush errors, unless the previous one failed
- Run backlight update in a worker to avoid upsetting lockdep (Daniel)
- Drop backlight_ops.get_brightness, there's no readback from the device
so it doesn't really add anything.
- Set dma mask, needed by dma-buf importers
v6:
- Use obj-y in Makefile (Peter)
- Fix missing le32_to_cpu() when using GUD_DISPLAY_MAGIC (Peter)
- Set initial brightness on backlight device
v7:
- LZ4_compress_default() can return zero, check for that
- Fix memory leak in gud_pipe_check() error path (Peter)
- Improve debug and error messages (Peter)
- Don't pass length in protocol structs (Peter)
- Pass USB interface to gud_usb_control_msg() et al. (Peter)
- Improve gud_connector_fill_properties() (Peter)
- Add GUD_PIXEL_FORMAT_RGB111 (Peter)
- Remove GUD_REQ_SET_VERSION (Peter)
- Fix DRM_IOCTL_MODE_OBJ_SETPROPERTY and the rotation property
- Fix dma-buf import (Thomas)
v8:
- Forgot to filter RGB111 from reaching userspace
- Handle a device that only returns unknown device properties (Peter)
- s/GUD_PIXEL_FORMAT_RGB111/GUD_PIXEL_FORMAT_XRGB1111/ (Peter)
- Fix R1 and XRGB1111 format conversion
- Add FIXME about Big Endian being broken (Peter, Ilia)
Cc: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210313112545.37527-4-noralf@tronnes.org
2021-03-13 12:25:45 +01:00
if ( ! xrgb8888_emulation_format )
xrgb8888_emulation_format = info ;
break ;
case DRM_FORMAT_RGB565 :
rgb565_supported = true ;
if ( ! xrgb8888_emulation_format )
xrgb8888_emulation_format = info ;
break ;
case DRM_FORMAT_XRGB8888 :
xrgb8888_supported = true ;
break ;
2021-03-22 18:44:34 +01:00
}
drm: Add GUD USB Display driver
This adds a USB display driver with the intention that it can be
used with future USB interfaced low end displays/adapters. The Linux
gadget device driver will serve as the canonical device implementation.
The following DRM properties are supported:
- Plane rotation
- Connector TV properties
There is also support for backlight brightness exposed as a backlight
device.
Display modes can be made available to the host driver either as DRM
display modes or through EDID. If both are present, EDID is just passed
on to userspace.
Performance is preferred over color depth, so if the device supports
RGB565, DRM_CAP_DUMB_PREFERRED_DEPTH will return 16.
If the device transfer buffer can't fit an uncompressed framebuffer
update, the update is split up into parts that do fit.
Optimal user experience is achieved by providing damage reports either by
setting FB_DAMAGE_CLIPS on pageflips or calling DRM_IOCTL_MODE_DIRTYFB.
LZ4 compression is used if the device supports it.
The driver supports a one bit monochrome transfer format: R1. This is not
implemented in the gadget driver. It is added in preparation for future
monochrome e-ink displays.
The driver is MIT licensed to smooth the path for any BSD port of the
driver.
v2:
- Use devm_drm_dev_alloc() and drmm_mode_config_init()
- drm_fbdev_generic_setup: Use preferred_bpp=0, 16 was a copy paste error
- The drm_backlight_helper is dropped, copy in the code
- Support protocol version backwards compatibility for device
v3:
- Use donated Openmoko USB pid
- Use direct compression from framebuffer when pitch matches, not only on
full frames, so split updates can benefit
- Use __le16 in struct gud_drm_req_get_connector_status
- Set edid property when the device only provides edid
- Clear compression fields in struct gud_drm_req_set_buffer
- Fix protocol version negotiation
- Remove mode->vrefresh, it's calculated
v4:
- Drop the status req polling which was a workaround for something that
turned out to be a dwc2 udc driver problem
- Add a flag for the Linux gadget to require a status request on
SET operations. Other devices will only get status req on STALL errors
- Use protocol specific error codes (Peter)
- Add a flag for devices that want to receive the entire framebuffer on
each flush (Lubomir)
- Retry a failed framebuffer flush
- If mode has changed wait for worker and clear pending damage before
queuing up new damage, fb width/height might have changed
- Increase error counter on bulk transfer failures
- Use DRM_MODE_CONNECTOR_USB
- Handle R1 kmalloc error (Peter)
- Don't try and replicate the USB get descriptor request standard for the
display descriptor (Peter)
- Make max_buffer_size optional (Peter), drop the pow2 requirement since
it's not necessary anymore.
- Don't pre-alloc a control request buffer, it was only 4k
- Let gud.h describe the whole protocol explicitly and don't let DRM
leak into it (Peter)
- Drop display mode .hskew and .vscan from the protocol
- Shorten names: s/GUD_DRM_/GUD_/ s/gud_drm_/gud_/ (Peter)
- Fix gud_pipe_check() connector picking when switching connector
- Drop gud_drm_driver_gem_create_object() cached is default now
- Retrieve USB device from struct drm_device.dev instead of keeping a
pointer
- Honour fb->offsets[0]
- Fix mode fetching when connector status is forced
- Check EDID length reported by the device
- Use drm_do_get_edid() so userspace can overrride EDID
- Set epoch counter to signal connector status change
- gud_drm_driver can be const now
v5:
- GUD_DRM_FORMAT_R1: Use non-human ascii values (Daniel)
- Change name to: GUD USB Display (Thomas, Simon)
- Change one __u32 -> __le32 in protocol header
- Always log fb flush errors, unless the previous one failed
- Run backlight update in a worker to avoid upsetting lockdep (Daniel)
- Drop backlight_ops.get_brightness, there's no readback from the device
so it doesn't really add anything.
- Set dma mask, needed by dma-buf importers
v6:
- Use obj-y in Makefile (Peter)
- Fix missing le32_to_cpu() when using GUD_DISPLAY_MAGIC (Peter)
- Set initial brightness on backlight device
v7:
- LZ4_compress_default() can return zero, check for that
- Fix memory leak in gud_pipe_check() error path (Peter)
- Improve debug and error messages (Peter)
- Don't pass length in protocol structs (Peter)
- Pass USB interface to gud_usb_control_msg() et al. (Peter)
- Improve gud_connector_fill_properties() (Peter)
- Add GUD_PIXEL_FORMAT_RGB111 (Peter)
- Remove GUD_REQ_SET_VERSION (Peter)
- Fix DRM_IOCTL_MODE_OBJ_SETPROPERTY and the rotation property
- Fix dma-buf import (Thomas)
v8:
- Forgot to filter RGB111 from reaching userspace
- Handle a device that only returns unknown device properties (Peter)
- s/GUD_PIXEL_FORMAT_RGB111/GUD_PIXEL_FORMAT_XRGB1111/ (Peter)
- Fix R1 and XRGB1111 format conversion
- Add FIXME about Big Endian being broken (Peter, Ilia)
Cc: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210313112545.37527-4-noralf@tronnes.org
2021-03-13 12:25:45 +01:00
fmt_buf_size = drm_format_info_min_pitch ( info , 0 , drm - > mode_config . max_width ) *
drm - > mode_config . max_height ;
max_buffer_size = max ( max_buffer_size , fmt_buf_size ) ;
if ( format = = GUD_DRM_FORMAT_R1 | | format = = GUD_DRM_FORMAT_XRGB1111 )
continue ; /* Internal not for userspace */
formats [ num_formats + + ] = format ;
}
if ( ! num_formats & & ! xrgb8888_emulation_format ) {
dev_err ( dev , " No supported pixel formats found \n " ) ;
return - EINVAL ;
}
/* Prefer speed over color depth */
if ( rgb565_supported )
drm - > mode_config . preferred_depth = 16 ;
if ( ! xrgb8888_supported & & xrgb8888_emulation_format ) {
gdrm - > xrgb8888_emulation_format = xrgb8888_emulation_format ;
formats [ num_formats + + ] = DRM_FORMAT_XRGB8888 ;
}
if ( desc . max_buffer_size )
max_buffer_size = le32_to_cpu ( desc . max_buffer_size ) ;
2021-07-01 19:07:48 +02:00
/* Prevent a misbehaving device from allocating loads of RAM. 4096x4096@XRGB8888 = 64 MB */
if ( max_buffer_size > SZ_64M )
max_buffer_size = SZ_64M ;
drm: Add GUD USB Display driver
This adds a USB display driver with the intention that it can be
used with future USB interfaced low end displays/adapters. The Linux
gadget device driver will serve as the canonical device implementation.
The following DRM properties are supported:
- Plane rotation
- Connector TV properties
There is also support for backlight brightness exposed as a backlight
device.
Display modes can be made available to the host driver either as DRM
display modes or through EDID. If both are present, EDID is just passed
on to userspace.
Performance is preferred over color depth, so if the device supports
RGB565, DRM_CAP_DUMB_PREFERRED_DEPTH will return 16.
If the device transfer buffer can't fit an uncompressed framebuffer
update, the update is split up into parts that do fit.
Optimal user experience is achieved by providing damage reports either by
setting FB_DAMAGE_CLIPS on pageflips or calling DRM_IOCTL_MODE_DIRTYFB.
LZ4 compression is used if the device supports it.
The driver supports a one bit monochrome transfer format: R1. This is not
implemented in the gadget driver. It is added in preparation for future
monochrome e-ink displays.
The driver is MIT licensed to smooth the path for any BSD port of the
driver.
v2:
- Use devm_drm_dev_alloc() and drmm_mode_config_init()
- drm_fbdev_generic_setup: Use preferred_bpp=0, 16 was a copy paste error
- The drm_backlight_helper is dropped, copy in the code
- Support protocol version backwards compatibility for device
v3:
- Use donated Openmoko USB pid
- Use direct compression from framebuffer when pitch matches, not only on
full frames, so split updates can benefit
- Use __le16 in struct gud_drm_req_get_connector_status
- Set edid property when the device only provides edid
- Clear compression fields in struct gud_drm_req_set_buffer
- Fix protocol version negotiation
- Remove mode->vrefresh, it's calculated
v4:
- Drop the status req polling which was a workaround for something that
turned out to be a dwc2 udc driver problem
- Add a flag for the Linux gadget to require a status request on
SET operations. Other devices will only get status req on STALL errors
- Use protocol specific error codes (Peter)
- Add a flag for devices that want to receive the entire framebuffer on
each flush (Lubomir)
- Retry a failed framebuffer flush
- If mode has changed wait for worker and clear pending damage before
queuing up new damage, fb width/height might have changed
- Increase error counter on bulk transfer failures
- Use DRM_MODE_CONNECTOR_USB
- Handle R1 kmalloc error (Peter)
- Don't try and replicate the USB get descriptor request standard for the
display descriptor (Peter)
- Make max_buffer_size optional (Peter), drop the pow2 requirement since
it's not necessary anymore.
- Don't pre-alloc a control request buffer, it was only 4k
- Let gud.h describe the whole protocol explicitly and don't let DRM
leak into it (Peter)
- Drop display mode .hskew and .vscan from the protocol
- Shorten names: s/GUD_DRM_/GUD_/ s/gud_drm_/gud_/ (Peter)
- Fix gud_pipe_check() connector picking when switching connector
- Drop gud_drm_driver_gem_create_object() cached is default now
- Retrieve USB device from struct drm_device.dev instead of keeping a
pointer
- Honour fb->offsets[0]
- Fix mode fetching when connector status is forced
- Check EDID length reported by the device
- Use drm_do_get_edid() so userspace can overrride EDID
- Set epoch counter to signal connector status change
- gud_drm_driver can be const now
v5:
- GUD_DRM_FORMAT_R1: Use non-human ascii values (Daniel)
- Change name to: GUD USB Display (Thomas, Simon)
- Change one __u32 -> __le32 in protocol header
- Always log fb flush errors, unless the previous one failed
- Run backlight update in a worker to avoid upsetting lockdep (Daniel)
- Drop backlight_ops.get_brightness, there's no readback from the device
so it doesn't really add anything.
- Set dma mask, needed by dma-buf importers
v6:
- Use obj-y in Makefile (Peter)
- Fix missing le32_to_cpu() when using GUD_DISPLAY_MAGIC (Peter)
- Set initial brightness on backlight device
v7:
- LZ4_compress_default() can return zero, check for that
- Fix memory leak in gud_pipe_check() error path (Peter)
- Improve debug and error messages (Peter)
- Don't pass length in protocol structs (Peter)
- Pass USB interface to gud_usb_control_msg() et al. (Peter)
- Improve gud_connector_fill_properties() (Peter)
- Add GUD_PIXEL_FORMAT_RGB111 (Peter)
- Remove GUD_REQ_SET_VERSION (Peter)
- Fix DRM_IOCTL_MODE_OBJ_SETPROPERTY and the rotation property
- Fix dma-buf import (Thomas)
v8:
- Forgot to filter RGB111 from reaching userspace
- Handle a device that only returns unknown device properties (Peter)
- s/GUD_PIXEL_FORMAT_RGB111/GUD_PIXEL_FORMAT_XRGB1111/ (Peter)
- Fix R1 and XRGB1111 format conversion
- Add FIXME about Big Endian being broken (Peter, Ilia)
Cc: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210313112545.37527-4-noralf@tronnes.org
2021-03-13 12:25:45 +01:00
gdrm - > bulk_pipe = usb_sndbulkpipe ( interface_to_usbdev ( intf ) , usb_endpoint_num ( bulk_out ) ) ;
gdrm - > bulk_len = max_buffer_size ;
2021-07-01 19:07:48 +02:00
ret = gud_alloc_bulk_buffer ( gdrm ) ;
if ( ret )
return ret ;
drm: Add GUD USB Display driver
This adds a USB display driver with the intention that it can be
used with future USB interfaced low end displays/adapters. The Linux
gadget device driver will serve as the canonical device implementation.
The following DRM properties are supported:
- Plane rotation
- Connector TV properties
There is also support for backlight brightness exposed as a backlight
device.
Display modes can be made available to the host driver either as DRM
display modes or through EDID. If both are present, EDID is just passed
on to userspace.
Performance is preferred over color depth, so if the device supports
RGB565, DRM_CAP_DUMB_PREFERRED_DEPTH will return 16.
If the device transfer buffer can't fit an uncompressed framebuffer
update, the update is split up into parts that do fit.
Optimal user experience is achieved by providing damage reports either by
setting FB_DAMAGE_CLIPS on pageflips or calling DRM_IOCTL_MODE_DIRTYFB.
LZ4 compression is used if the device supports it.
The driver supports a one bit monochrome transfer format: R1. This is not
implemented in the gadget driver. It is added in preparation for future
monochrome e-ink displays.
The driver is MIT licensed to smooth the path for any BSD port of the
driver.
v2:
- Use devm_drm_dev_alloc() and drmm_mode_config_init()
- drm_fbdev_generic_setup: Use preferred_bpp=0, 16 was a copy paste error
- The drm_backlight_helper is dropped, copy in the code
- Support protocol version backwards compatibility for device
v3:
- Use donated Openmoko USB pid
- Use direct compression from framebuffer when pitch matches, not only on
full frames, so split updates can benefit
- Use __le16 in struct gud_drm_req_get_connector_status
- Set edid property when the device only provides edid
- Clear compression fields in struct gud_drm_req_set_buffer
- Fix protocol version negotiation
- Remove mode->vrefresh, it's calculated
v4:
- Drop the status req polling which was a workaround for something that
turned out to be a dwc2 udc driver problem
- Add a flag for the Linux gadget to require a status request on
SET operations. Other devices will only get status req on STALL errors
- Use protocol specific error codes (Peter)
- Add a flag for devices that want to receive the entire framebuffer on
each flush (Lubomir)
- Retry a failed framebuffer flush
- If mode has changed wait for worker and clear pending damage before
queuing up new damage, fb width/height might have changed
- Increase error counter on bulk transfer failures
- Use DRM_MODE_CONNECTOR_USB
- Handle R1 kmalloc error (Peter)
- Don't try and replicate the USB get descriptor request standard for the
display descriptor (Peter)
- Make max_buffer_size optional (Peter), drop the pow2 requirement since
it's not necessary anymore.
- Don't pre-alloc a control request buffer, it was only 4k
- Let gud.h describe the whole protocol explicitly and don't let DRM
leak into it (Peter)
- Drop display mode .hskew and .vscan from the protocol
- Shorten names: s/GUD_DRM_/GUD_/ s/gud_drm_/gud_/ (Peter)
- Fix gud_pipe_check() connector picking when switching connector
- Drop gud_drm_driver_gem_create_object() cached is default now
- Retrieve USB device from struct drm_device.dev instead of keeping a
pointer
- Honour fb->offsets[0]
- Fix mode fetching when connector status is forced
- Check EDID length reported by the device
- Use drm_do_get_edid() so userspace can overrride EDID
- Set epoch counter to signal connector status change
- gud_drm_driver can be const now
v5:
- GUD_DRM_FORMAT_R1: Use non-human ascii values (Daniel)
- Change name to: GUD USB Display (Thomas, Simon)
- Change one __u32 -> __le32 in protocol header
- Always log fb flush errors, unless the previous one failed
- Run backlight update in a worker to avoid upsetting lockdep (Daniel)
- Drop backlight_ops.get_brightness, there's no readback from the device
so it doesn't really add anything.
- Set dma mask, needed by dma-buf importers
v6:
- Use obj-y in Makefile (Peter)
- Fix missing le32_to_cpu() when using GUD_DISPLAY_MAGIC (Peter)
- Set initial brightness on backlight device
v7:
- LZ4_compress_default() can return zero, check for that
- Fix memory leak in gud_pipe_check() error path (Peter)
- Improve debug and error messages (Peter)
- Don't pass length in protocol structs (Peter)
- Pass USB interface to gud_usb_control_msg() et al. (Peter)
- Improve gud_connector_fill_properties() (Peter)
- Add GUD_PIXEL_FORMAT_RGB111 (Peter)
- Remove GUD_REQ_SET_VERSION (Peter)
- Fix DRM_IOCTL_MODE_OBJ_SETPROPERTY and the rotation property
- Fix dma-buf import (Thomas)
v8:
- Forgot to filter RGB111 from reaching userspace
- Handle a device that only returns unknown device properties (Peter)
- s/GUD_PIXEL_FORMAT_RGB111/GUD_PIXEL_FORMAT_XRGB1111/ (Peter)
- Fix R1 and XRGB1111 format conversion
- Add FIXME about Big Endian being broken (Peter, Ilia)
Cc: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210313112545.37527-4-noralf@tronnes.org
2021-03-13 12:25:45 +01:00
if ( gdrm - > compression & GUD_COMPRESSION_LZ4 ) {
gdrm - > lz4_comp_mem = devm_kmalloc ( dev , LZ4_MEM_COMPRESS , GFP_KERNEL ) ;
if ( ! gdrm - > lz4_comp_mem )
return - ENOMEM ;
gdrm - > compress_buf = vmalloc ( gdrm - > bulk_len ) ;
if ( ! gdrm - > compress_buf )
return - ENOMEM ;
}
ret = drm_simple_display_pipe_init ( drm , & gdrm - > pipe , & gud_pipe_funcs ,
formats , num_formats ,
gud_pipe_modifiers , NULL ) ;
if ( ret )
return ret ;
devm_kfree ( dev , formats ) ;
devm_kfree ( dev , formats_dev ) ;
ret = gud_get_properties ( gdrm ) ;
if ( ret ) {
dev_err ( dev , " Failed to get properties (error=%d) \n " , ret ) ;
return ret ;
}
drm_plane_enable_fb_damage_clips ( & gdrm - > pipe . plane ) ;
ret = gud_get_connectors ( gdrm ) ;
if ( ret ) {
dev_err ( dev , " Failed to get connectors (error=%d) \n " , ret ) ;
return ret ;
}
drm_mode_config_reset ( drm ) ;
usb_set_intfdata ( intf , gdrm ) ;
gdrm - > dmadev = usb_intf_get_dma_device ( intf ) ;
if ( ! gdrm - > dmadev )
dev_warn ( dev , " buffer sharing not supported " ) ;
2022-12-26 12:50:22 -03:00
drm_debugfs_add_file ( drm , " stats " , gud_stats_debugfs , NULL ) ;
drm: Add GUD USB Display driver
This adds a USB display driver with the intention that it can be
used with future USB interfaced low end displays/adapters. The Linux
gadget device driver will serve as the canonical device implementation.
The following DRM properties are supported:
- Plane rotation
- Connector TV properties
There is also support for backlight brightness exposed as a backlight
device.
Display modes can be made available to the host driver either as DRM
display modes or through EDID. If both are present, EDID is just passed
on to userspace.
Performance is preferred over color depth, so if the device supports
RGB565, DRM_CAP_DUMB_PREFERRED_DEPTH will return 16.
If the device transfer buffer can't fit an uncompressed framebuffer
update, the update is split up into parts that do fit.
Optimal user experience is achieved by providing damage reports either by
setting FB_DAMAGE_CLIPS on pageflips or calling DRM_IOCTL_MODE_DIRTYFB.
LZ4 compression is used if the device supports it.
The driver supports a one bit monochrome transfer format: R1. This is not
implemented in the gadget driver. It is added in preparation for future
monochrome e-ink displays.
The driver is MIT licensed to smooth the path for any BSD port of the
driver.
v2:
- Use devm_drm_dev_alloc() and drmm_mode_config_init()
- drm_fbdev_generic_setup: Use preferred_bpp=0, 16 was a copy paste error
- The drm_backlight_helper is dropped, copy in the code
- Support protocol version backwards compatibility for device
v3:
- Use donated Openmoko USB pid
- Use direct compression from framebuffer when pitch matches, not only on
full frames, so split updates can benefit
- Use __le16 in struct gud_drm_req_get_connector_status
- Set edid property when the device only provides edid
- Clear compression fields in struct gud_drm_req_set_buffer
- Fix protocol version negotiation
- Remove mode->vrefresh, it's calculated
v4:
- Drop the status req polling which was a workaround for something that
turned out to be a dwc2 udc driver problem
- Add a flag for the Linux gadget to require a status request on
SET operations. Other devices will only get status req on STALL errors
- Use protocol specific error codes (Peter)
- Add a flag for devices that want to receive the entire framebuffer on
each flush (Lubomir)
- Retry a failed framebuffer flush
- If mode has changed wait for worker and clear pending damage before
queuing up new damage, fb width/height might have changed
- Increase error counter on bulk transfer failures
- Use DRM_MODE_CONNECTOR_USB
- Handle R1 kmalloc error (Peter)
- Don't try and replicate the USB get descriptor request standard for the
display descriptor (Peter)
- Make max_buffer_size optional (Peter), drop the pow2 requirement since
it's not necessary anymore.
- Don't pre-alloc a control request buffer, it was only 4k
- Let gud.h describe the whole protocol explicitly and don't let DRM
leak into it (Peter)
- Drop display mode .hskew and .vscan from the protocol
- Shorten names: s/GUD_DRM_/GUD_/ s/gud_drm_/gud_/ (Peter)
- Fix gud_pipe_check() connector picking when switching connector
- Drop gud_drm_driver_gem_create_object() cached is default now
- Retrieve USB device from struct drm_device.dev instead of keeping a
pointer
- Honour fb->offsets[0]
- Fix mode fetching when connector status is forced
- Check EDID length reported by the device
- Use drm_do_get_edid() so userspace can overrride EDID
- Set epoch counter to signal connector status change
- gud_drm_driver can be const now
v5:
- GUD_DRM_FORMAT_R1: Use non-human ascii values (Daniel)
- Change name to: GUD USB Display (Thomas, Simon)
- Change one __u32 -> __le32 in protocol header
- Always log fb flush errors, unless the previous one failed
- Run backlight update in a worker to avoid upsetting lockdep (Daniel)
- Drop backlight_ops.get_brightness, there's no readback from the device
so it doesn't really add anything.
- Set dma mask, needed by dma-buf importers
v6:
- Use obj-y in Makefile (Peter)
- Fix missing le32_to_cpu() when using GUD_DISPLAY_MAGIC (Peter)
- Set initial brightness on backlight device
v7:
- LZ4_compress_default() can return zero, check for that
- Fix memory leak in gud_pipe_check() error path (Peter)
- Improve debug and error messages (Peter)
- Don't pass length in protocol structs (Peter)
- Pass USB interface to gud_usb_control_msg() et al. (Peter)
- Improve gud_connector_fill_properties() (Peter)
- Add GUD_PIXEL_FORMAT_RGB111 (Peter)
- Remove GUD_REQ_SET_VERSION (Peter)
- Fix DRM_IOCTL_MODE_OBJ_SETPROPERTY and the rotation property
- Fix dma-buf import (Thomas)
v8:
- Forgot to filter RGB111 from reaching userspace
- Handle a device that only returns unknown device properties (Peter)
- s/GUD_PIXEL_FORMAT_RGB111/GUD_PIXEL_FORMAT_XRGB1111/ (Peter)
- Fix R1 and XRGB1111 format conversion
- Add FIXME about Big Endian being broken (Peter, Ilia)
Cc: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210313112545.37527-4-noralf@tronnes.org
2021-03-13 12:25:45 +01:00
ret = drm_dev_register ( drm , 0 ) ;
if ( ret ) {
put_device ( gdrm - > dmadev ) ;
return ret ;
}
drm_kms_helper_poll_init ( drm ) ;
drm_fbdev_generic_setup ( drm , 0 ) ;
return 0 ;
}
static void gud_disconnect ( struct usb_interface * interface )
{
struct gud_device * gdrm = usb_get_intfdata ( interface ) ;
struct drm_device * drm = & gdrm - > drm ;
drm_dbg ( drm , " %s: \n " , __func__ ) ;
drm_kms_helper_poll_fini ( drm ) ;
drm_dev_unplug ( drm ) ;
drm_atomic_helper_shutdown ( drm ) ;
put_device ( gdrm - > dmadev ) ;
gdrm - > dmadev = NULL ;
}
static int gud_suspend ( struct usb_interface * intf , pm_message_t message )
{
struct gud_device * gdrm = usb_get_intfdata ( intf ) ;
return drm_mode_config_helper_suspend ( & gdrm - > drm ) ;
}
static int gud_resume ( struct usb_interface * intf )
{
struct gud_device * gdrm = usb_get_intfdata ( intf ) ;
drm_mode_config_helper_resume ( & gdrm - > drm ) ;
return 0 ;
}
static const struct usb_device_id gud_id_table [ ] = {
{ USB_DEVICE_INTERFACE_CLASS ( 0x1d50 , 0x614d , USB_CLASS_VENDOR_SPEC ) } ,
2021-07-03 16:13:20 +02:00
{ USB_DEVICE_INTERFACE_CLASS ( 0x16d0 , 0x10a9 , USB_CLASS_VENDOR_SPEC ) } ,
drm: Add GUD USB Display driver
This adds a USB display driver with the intention that it can be
used with future USB interfaced low end displays/adapters. The Linux
gadget device driver will serve as the canonical device implementation.
The following DRM properties are supported:
- Plane rotation
- Connector TV properties
There is also support for backlight brightness exposed as a backlight
device.
Display modes can be made available to the host driver either as DRM
display modes or through EDID. If both are present, EDID is just passed
on to userspace.
Performance is preferred over color depth, so if the device supports
RGB565, DRM_CAP_DUMB_PREFERRED_DEPTH will return 16.
If the device transfer buffer can't fit an uncompressed framebuffer
update, the update is split up into parts that do fit.
Optimal user experience is achieved by providing damage reports either by
setting FB_DAMAGE_CLIPS on pageflips or calling DRM_IOCTL_MODE_DIRTYFB.
LZ4 compression is used if the device supports it.
The driver supports a one bit monochrome transfer format: R1. This is not
implemented in the gadget driver. It is added in preparation for future
monochrome e-ink displays.
The driver is MIT licensed to smooth the path for any BSD port of the
driver.
v2:
- Use devm_drm_dev_alloc() and drmm_mode_config_init()
- drm_fbdev_generic_setup: Use preferred_bpp=0, 16 was a copy paste error
- The drm_backlight_helper is dropped, copy in the code
- Support protocol version backwards compatibility for device
v3:
- Use donated Openmoko USB pid
- Use direct compression from framebuffer when pitch matches, not only on
full frames, so split updates can benefit
- Use __le16 in struct gud_drm_req_get_connector_status
- Set edid property when the device only provides edid
- Clear compression fields in struct gud_drm_req_set_buffer
- Fix protocol version negotiation
- Remove mode->vrefresh, it's calculated
v4:
- Drop the status req polling which was a workaround for something that
turned out to be a dwc2 udc driver problem
- Add a flag for the Linux gadget to require a status request on
SET operations. Other devices will only get status req on STALL errors
- Use protocol specific error codes (Peter)
- Add a flag for devices that want to receive the entire framebuffer on
each flush (Lubomir)
- Retry a failed framebuffer flush
- If mode has changed wait for worker and clear pending damage before
queuing up new damage, fb width/height might have changed
- Increase error counter on bulk transfer failures
- Use DRM_MODE_CONNECTOR_USB
- Handle R1 kmalloc error (Peter)
- Don't try and replicate the USB get descriptor request standard for the
display descriptor (Peter)
- Make max_buffer_size optional (Peter), drop the pow2 requirement since
it's not necessary anymore.
- Don't pre-alloc a control request buffer, it was only 4k
- Let gud.h describe the whole protocol explicitly and don't let DRM
leak into it (Peter)
- Drop display mode .hskew and .vscan from the protocol
- Shorten names: s/GUD_DRM_/GUD_/ s/gud_drm_/gud_/ (Peter)
- Fix gud_pipe_check() connector picking when switching connector
- Drop gud_drm_driver_gem_create_object() cached is default now
- Retrieve USB device from struct drm_device.dev instead of keeping a
pointer
- Honour fb->offsets[0]
- Fix mode fetching when connector status is forced
- Check EDID length reported by the device
- Use drm_do_get_edid() so userspace can overrride EDID
- Set epoch counter to signal connector status change
- gud_drm_driver can be const now
v5:
- GUD_DRM_FORMAT_R1: Use non-human ascii values (Daniel)
- Change name to: GUD USB Display (Thomas, Simon)
- Change one __u32 -> __le32 in protocol header
- Always log fb flush errors, unless the previous one failed
- Run backlight update in a worker to avoid upsetting lockdep (Daniel)
- Drop backlight_ops.get_brightness, there's no readback from the device
so it doesn't really add anything.
- Set dma mask, needed by dma-buf importers
v6:
- Use obj-y in Makefile (Peter)
- Fix missing le32_to_cpu() when using GUD_DISPLAY_MAGIC (Peter)
- Set initial brightness on backlight device
v7:
- LZ4_compress_default() can return zero, check for that
- Fix memory leak in gud_pipe_check() error path (Peter)
- Improve debug and error messages (Peter)
- Don't pass length in protocol structs (Peter)
- Pass USB interface to gud_usb_control_msg() et al. (Peter)
- Improve gud_connector_fill_properties() (Peter)
- Add GUD_PIXEL_FORMAT_RGB111 (Peter)
- Remove GUD_REQ_SET_VERSION (Peter)
- Fix DRM_IOCTL_MODE_OBJ_SETPROPERTY and the rotation property
- Fix dma-buf import (Thomas)
v8:
- Forgot to filter RGB111 from reaching userspace
- Handle a device that only returns unknown device properties (Peter)
- s/GUD_PIXEL_FORMAT_RGB111/GUD_PIXEL_FORMAT_XRGB1111/ (Peter)
- Fix R1 and XRGB1111 format conversion
- Add FIXME about Big Endian being broken (Peter, Ilia)
Cc: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210313112545.37527-4-noralf@tronnes.org
2021-03-13 12:25:45 +01:00
{ }
} ;
MODULE_DEVICE_TABLE ( usb , gud_id_table ) ;
static struct usb_driver gud_usb_driver = {
. name = " gud " ,
. probe = gud_probe ,
. disconnect = gud_disconnect ,
. id_table = gud_id_table ,
. suspend = gud_suspend ,
. resume = gud_resume ,
. reset_resume = gud_resume ,
} ;
module_usb_driver ( gud_usb_driver ) ;
MODULE_AUTHOR ( " Noralf Trønnes " ) ;
MODULE_LICENSE ( " Dual MIT/GPL " ) ;