linux/drivers/acpi/sleep.c

1071 lines
26 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0-only
/*
* sleep.c - ACPI sleep support.
*
* Copyright (c) 2005 Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
* Copyright (c) 2004 David Shaohua Li <shaohua.li@intel.com>
* Copyright (c) 2000-2003 Patrick Mochel
* Copyright (c) 2003 Open Source Development Lab
*/
#define pr_fmt(fmt) "ACPI: PM: " fmt
#include <linux/delay.h>
#include <linux/irq.h>
#include <linux/dmi.h>
#include <linux/device.h>
#include <linux/interrupt.h>
#include <linux/suspend.h>
#include <linux/reboot.h>
#include <linux/acpi.h>
#include <linux/module.h>
#include <linux/syscore_ops.h>
#include <asm/io.h>
#include <trace/events/power.h>
#include "internal.h"
#include "sleep.h"
/*
* Some HW-full platforms do not have _S5, so they may need
* to leverage efi power off for a shutdown.
*/
bool acpi_no_s5;
static u8 sleep_states[ACPI_S_STATE_COUNT];
static void acpi_sleep_tts_switch(u32 acpi_state)
{
acpi_status status;
status = acpi_execute_simple_method(NULL, "\\_TTS", acpi_state);
if (ACPI_FAILURE(status) && status != AE_NOT_FOUND) {
/*
* OS can't evaluate the _TTS object correctly. Some warning
* message will be printed. But it won't break anything.
*/
pr_notice("Failure in evaluating _TTS object\n");
}
}
static int tts_notify_reboot(struct notifier_block *this,
unsigned long code, void *x)
{
acpi_sleep_tts_switch(ACPI_STATE_S5);
return NOTIFY_DONE;
}
static struct notifier_block tts_notifier = {
.notifier_call = tts_notify_reboot,
.next = NULL,
.priority = 0,
};
static int acpi_sleep_prepare(u32 acpi_state)
{
#ifdef CONFIG_ACPI_SLEEP
unsigned long acpi_wakeup_address;
/* do we have a wakeup address for S2 and S3? */
if (acpi_state == ACPI_STATE_S3) {
acpi_wakeup_address = acpi_get_wakeup_address();
if (!acpi_wakeup_address)
return -EFAULT;
acpi_set_waking_vector(acpi_wakeup_address);
}
ACPI_FLUSH_CPU_CACHE();
#endif
pr_info("Preparing to enter system sleep state S%d\n", acpi_state);
acpi_enable_wakeup_devices(acpi_state);
acpi_enter_sleep_state_prep(acpi_state);
return 0;
}
bool acpi_sleep_state_supported(u8 sleep_state)
{
acpi_status status;
u8 type_a, type_b;
status = acpi_get_sleep_type_data(sleep_state, &type_a, &type_b);
return ACPI_SUCCESS(status) && (!acpi_gbl_reduced_hardware
|| (acpi_gbl_FADT.sleep_control.address
&& acpi_gbl_FADT.sleep_status.address));
}
#ifdef CONFIG_ACPI_SLEEP
static u32 acpi_target_sleep_state = ACPI_STATE_S0;
u32 acpi_target_system_state(void)
{
return acpi_target_sleep_state;
}
EXPORT_SYMBOL_GPL(acpi_target_system_state);
static bool pwr_btn_event_pending;
/*
* The ACPI specification wants us to save NVS memory regions during hibernation
* and to restore them during the subsequent resume. Windows does that also for
* suspend to RAM. However, it is known that this mechanism does not work on
* all machines, so we allow the user to disable it with the help of the
* 'acpi_sleep=nonvs' kernel command line option.
*/
static bool nvs_nosave;
void __init acpi_nvs_nosave(void)
{
nvs_nosave = true;
}
/*
* The ACPI specification wants us to save NVS memory regions during hibernation
* but says nothing about saving NVS during S3. Not all versions of Windows
* save NVS on S3 suspend either, and it is clear that not all systems need
* NVS to be saved at S3 time. To improve suspend/resume time, allow the
* user to disable saving NVS on S3 if their system does not require it, but
* continue to save/restore NVS for S4 as specified.
*/
static bool nvs_nosave_s3;
void __init acpi_nvs_nosave_s3(void)
{
nvs_nosave_s3 = true;
}
static int __init init_nvs_save_s3(const struct dmi_system_id *d)
{
nvs_nosave_s3 = false;
return 0;
}
/*
* ACPI 1.0 wants us to execute _PTS before suspending devices, so we allow the
* user to request that behavior by using the 'acpi_old_suspend_ordering'
* kernel command line option that causes the following variable to be set.
*/
static bool old_suspend_ordering;
void __init acpi_old_suspend_ordering(void)
{
old_suspend_ordering = true;
}
static int __init init_old_suspend_ordering(const struct dmi_system_id *d)
{
acpi_old_suspend_ordering();
return 0;
}
static int __init init_nvs_nosave(const struct dmi_system_id *d)
{
acpi_nvs_nosave();
return 0;
}
bool acpi_sleep_default_s3;
static int __init init_default_s3(const struct dmi_system_id *d)
{
acpi_sleep_default_s3 = true;
return 0;
}
static const struct dmi_system_id acpisleep_dmi_table[] __initconst = {
{
.callback = init_old_suspend_ordering,
.ident = "Abit KN9 (nForce4 variant)",
.matches = {
DMI_MATCH(DMI_BOARD_VENDOR, "http://www.abit.com.tw/"),
DMI_MATCH(DMI_BOARD_NAME, "KN9 Series(NF-CK804)"),
},
},
{
.callback = init_old_suspend_ordering,
.ident = "HP xw4600 Workstation",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
DMI_MATCH(DMI_PRODUCT_NAME, "HP xw4600 Workstation"),
},
},
{
.callback = init_old_suspend_ordering,
.ident = "Asus Pundit P1-AH2 (M2N8L motherboard)",
.matches = {
DMI_MATCH(DMI_BOARD_VENDOR, "ASUSTek Computer INC."),
DMI_MATCH(DMI_BOARD_NAME, "M2N8L"),
},
},
{
.callback = init_old_suspend_ordering,
.ident = "Panasonic CF51-2L",
.matches = {
DMI_MATCH(DMI_BOARD_VENDOR,
"Matsushita Electric Industrial Co.,Ltd."),
DMI_MATCH(DMI_BOARD_NAME, "CF51-2L"),
},
},
{
.callback = init_nvs_nosave,
.ident = "Sony Vaio VGN-FW41E_H",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),
DMI_MATCH(DMI_PRODUCT_NAME, "VGN-FW41E_H"),
},
},
{
.callback = init_nvs_nosave,
.ident = "Sony Vaio VGN-FW21E",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),
DMI_MATCH(DMI_PRODUCT_NAME, "VGN-FW21E"),
},
},
{
.callback = init_nvs_nosave,
.ident = "Sony Vaio VGN-FW21M",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),
DMI_MATCH(DMI_PRODUCT_NAME, "VGN-FW21M"),
},
},
{
.callback = init_nvs_nosave,
.ident = "Sony Vaio VPCEB17FX",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),
DMI_MATCH(DMI_PRODUCT_NAME, "VPCEB17FX"),
},
},
{
.callback = init_nvs_nosave,
.ident = "Sony Vaio VGN-SR11M",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),
DMI_MATCH(DMI_PRODUCT_NAME, "VGN-SR11M"),
},
},
{
.callback = init_nvs_nosave,
.ident = "Everex StepNote Series",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "Everex Systems, Inc."),
DMI_MATCH(DMI_PRODUCT_NAME, "Everex StepNote Series"),
},
},
{
.callback = init_nvs_nosave,
.ident = "Sony Vaio VPCEB1Z1E",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),
DMI_MATCH(DMI_PRODUCT_NAME, "VPCEB1Z1E"),
},
},
{
.callback = init_nvs_nosave,
.ident = "Sony Vaio VGN-NW130D",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),
DMI_MATCH(DMI_PRODUCT_NAME, "VGN-NW130D"),
},
},
{
.callback = init_nvs_nosave,
.ident = "Sony Vaio VPCCW29FX",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),
DMI_MATCH(DMI_PRODUCT_NAME, "VPCCW29FX"),
},
},
{
.callback = init_nvs_nosave,
.ident = "Averatec AV1020-ED2",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "AVERATEC"),
DMI_MATCH(DMI_PRODUCT_NAME, "1000 Series"),
},
},
{
.callback = init_old_suspend_ordering,
.ident = "Asus A8N-SLI DELUXE",
.matches = {
DMI_MATCH(DMI_BOARD_VENDOR, "ASUSTeK Computer INC."),
DMI_MATCH(DMI_BOARD_NAME, "A8N-SLI DELUXE"),
},
},
{
.callback = init_old_suspend_ordering,
.ident = "Asus A8N-SLI Premium",
.matches = {
DMI_MATCH(DMI_BOARD_VENDOR, "ASUSTeK Computer INC."),
DMI_MATCH(DMI_BOARD_NAME, "A8N-SLI Premium"),
},
},
{
.callback = init_nvs_nosave,
.ident = "Sony Vaio VGN-SR26GN_P",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),
DMI_MATCH(DMI_PRODUCT_NAME, "VGN-SR26GN_P"),
},
},
{
.callback = init_nvs_nosave,
.ident = "Sony Vaio VPCEB1S1E",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),
DMI_MATCH(DMI_PRODUCT_NAME, "VPCEB1S1E"),
},
},
{
.callback = init_nvs_nosave,
.ident = "Sony Vaio VGN-FW520F",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "Sony Corporation"),
DMI_MATCH(DMI_PRODUCT_NAME, "VGN-FW520F"),
},
},
{
.callback = init_nvs_nosave,
.ident = "Asus K54C",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK Computer Inc."),
DMI_MATCH(DMI_PRODUCT_NAME, "K54C"),
},
},
{
.callback = init_nvs_nosave,
.ident = "Asus K54HR",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK Computer Inc."),
DMI_MATCH(DMI_PRODUCT_NAME, "K54HR"),
},
},
{
.callback = init_nvs_save_s3,
.ident = "Asus 1025C",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
DMI_MATCH(DMI_PRODUCT_NAME, "1025C"),
},
},
/*
* https://bugzilla.kernel.org/show_bug.cgi?id=189431
* Lenovo G50-45 is a platform later than 2012, but needs nvs memory
* saving during S3.
*/
{
.callback = init_nvs_save_s3,
.ident = "Lenovo G50-45",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
DMI_MATCH(DMI_PRODUCT_NAME, "80E3"),
},
},
/*
* ThinkPad X1 Tablet(2016) cannot do suspend-to-idle using
* the Low Power S0 Idle firmware interface (see
* https://bugzilla.kernel.org/show_bug.cgi?id=199057).
*/
{
.callback = init_default_s3,
.ident = "ThinkPad X1 Tablet(2016)",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"),
DMI_MATCH(DMI_PRODUCT_NAME, "20GGA00L00"),
},
},
{},
};
static bool ignore_blacklist;
void __init acpi_sleep_no_blacklist(void)
{
ignore_blacklist = true;
}
static void __init acpi_sleep_dmi_check(void)
{
if (ignore_blacklist)
return;
if (dmi_get_bios_year() >= 2012)
acpi_nvs_nosave_s3();
dmi_check_system(acpisleep_dmi_table);
}
/**
* acpi_pm_freeze - Disable the GPEs and suspend EC transactions.
*/
static int acpi_pm_freeze(void)
{
acpi_disable_all_gpes();
acpi_os_wait_events_complete();
acpi_ec_block_transactions();
return 0;
}
/**
* acpi_pm_pre_suspend - Enable wakeup devices, "freeze" EC and save NVS.
*/
static int acpi_pm_pre_suspend(void)
{
acpi_pm_freeze();
return suspend_nvs_save();
}
/**
* __acpi_pm_prepare - Prepare the platform to enter the target state.
*
* If necessary, set the firmware waking vector and do arch-specific
* nastiness to get the wakeup code to the waking vector.
*/
static int __acpi_pm_prepare(void)
{
int error = acpi_sleep_prepare(acpi_target_sleep_state);
if (error)
acpi_target_sleep_state = ACPI_STATE_S0;
return error;
}
/**
* acpi_pm_prepare - Prepare the platform to enter the target sleep
* state and disable the GPEs.
*/
static int acpi_pm_prepare(void)
{
int error = __acpi_pm_prepare();
if (!error)
error = acpi_pm_pre_suspend();
return error;
}
/**
* acpi_pm_finish - Instruct the platform to leave a sleep state.
*
* This is called after we wake back up (or if entering the sleep state
* failed).
*/
static void acpi_pm_finish(void)
{
struct acpi_device *pwr_btn_adev;
u32 acpi_state = acpi_target_sleep_state;
acpi_ec_unblock_transactions();
suspend_nvs_free();
if (acpi_state == ACPI_STATE_S0)
return;
pr_info("Waking up from system sleep state S%d\n", acpi_state);
acpi_disable_wakeup_devices(acpi_state);
acpi_leave_sleep_state(acpi_state);
/* reset firmware waking vector */
acpi_set_waking_vector(0);
acpi_target_sleep_state = ACPI_STATE_S0;
acpi_resume_power_resources();
/* If we were woken with the fixed power button, provide a small
* hint to userspace in the form of a wakeup event on the fixed power
* button device (if it can be found).
*
* We delay the event generation til now, as the PM layer requires
* timekeeping to be running before we generate events. */
if (!pwr_btn_event_pending)
return;
pwr_btn_event_pending = false;
pwr_btn_adev = acpi_dev_get_first_match_dev(ACPI_BUTTON_HID_POWERF,
NULL, -1);
if (pwr_btn_adev) {
pm_wakeup_event(&pwr_btn_adev->dev, 0);
acpi_dev_put(pwr_btn_adev);
}
}
/**
* acpi_pm_start - Start system PM transition.
*/
static void acpi_pm_start(u32 acpi_state)
{
acpi_target_sleep_state = acpi_state;
acpi_sleep_tts_switch(acpi_target_sleep_state);
acpi_scan_lock_acquire();
}
/**
* acpi_pm_end - Finish up system PM transition.
*/
static void acpi_pm_end(void)
{
ACPI: power: Rework turning off unused power resources Make turning off unused power resources (after the enumeration of devices and during system-wide resume from S3) more straightforward by using the observation that the power resource state stored in struct acpi_power_resource can be used to determine whether or not the give power resource has any users. Namely, when the state of the power resource is unknown, its _STA method has never been evaluated (or the evaluation of it has failed) and its _ON and _OFF methods have never been executed (or they have failed to execute), so for all practical purposes it can be assumed to have no users (or to be unusable). Therefore, instead of checking the number of power resource users, it is sufficient to check if its state is known. Moreover, if the last known state of a given power resource is "off", it is not necessary to turn it off, because it has been used to initialize the power state or the wakeup power resources list of at least one device and either its _STA method has returned 0 ("off"), or its _OFF method has been successfully executed already. Accordingly, modify acpi_turn_off_unused_power_resources() to do the above checks (which are suitable for both uses of it) instead of using the number of power resource users or evaluating its _STA method, drop its argument (which is not useful any more) and update its callers. Also drop the users field from struct acpi_power_resource as it is not useful any more. Tested-by: Dave Olsthoorn <dave@bewaar.me> Tested-by: Shujun Wang <wsj20369@163.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2021-05-24 18:26:16 +03:00
acpi_turn_off_unused_power_resources();
acpi_scan_lock_release();
/*
* This is necessary in case acpi_pm_finish() is not called during a
* failing transition to a sleep state.
*/
acpi_target_sleep_state = ACPI_STATE_S0;
acpi_sleep_tts_switch(acpi_target_sleep_state);
}
#else /* !CONFIG_ACPI_SLEEP */
#define sleep_no_lps0 (1)
#define acpi_target_sleep_state ACPI_STATE_S0
#define acpi_sleep_default_s3 (1)
static inline void acpi_sleep_dmi_check(void) {}
#endif /* CONFIG_ACPI_SLEEP */
#ifdef CONFIG_SUSPEND
static u32 acpi_suspend_states[] = {
[PM_SUSPEND_ON] = ACPI_STATE_S0,
[PM_SUSPEND_STANDBY] = ACPI_STATE_S1,
[PM_SUSPEND_MEM] = ACPI_STATE_S3,
[PM_SUSPEND_MAX] = ACPI_STATE_S5
};
/**
* acpi_suspend_begin - Set the target system sleep state to the state
* associated with given @pm_state, if supported.
*/
static int acpi_suspend_begin(suspend_state_t pm_state)
{
u32 acpi_state = acpi_suspend_states[pm_state];
int error;
error = (nvs_nosave || nvs_nosave_s3) ? 0 : suspend_nvs_alloc();
if (error)
return error;
if (!sleep_states[acpi_state]) {
pr_err("ACPI does not support sleep state S%u\n", acpi_state);
return -ENOSYS;
}
if (acpi_state > ACPI_STATE_S1)
pm_set_suspend_via_firmware();
acpi_pm_start(acpi_state);
return 0;
}
/**
* acpi_suspend_enter - Actually enter a sleep state.
* @pm_state: ignored
*
* Flush caches and go to sleep. For STR we have to call arch-specific
* assembly, which in turn call acpi_enter_sleep_state().
* It's unfortunate, but it works. Please fix if you're feeling frisky.
*/
static int acpi_suspend_enter(suspend_state_t pm_state)
{
acpi_status status = AE_OK;
u32 acpi_state = acpi_target_sleep_state;
int error;
ACPI_FLUSH_CPU_CACHE();
trace_suspend_resume(TPS("acpi_suspend"), acpi_state, true);
switch (acpi_state) {
case ACPI_STATE_S1:
barrier();
status = acpi_enter_sleep_state(acpi_state);
break;
case ACPI_STATE_S3:
if (!acpi_suspend_lowlevel)
return -ENOSYS;
error = acpi_suspend_lowlevel();
if (error)
return error;
pr_info("Low-level resume complete\n");
pm_set_resume_via_firmware();
break;
}
trace_suspend_resume(TPS("acpi_suspend"), acpi_state, false);
/* This violates the spec but is required for bug compatibility. */
acpi_write_bit_register(ACPI_BITREG_SCI_ENABLE, 1);
/* Reprogram control registers */
acpi_leave_sleep_state_prep(acpi_state);
/* ACPI 3.0 specs (P62) says that it's the responsibility
* of the OSPM to clear the status bit [ implying that the
* POWER_BUTTON event should not reach userspace ]
*
* However, we do generate a small hint for userspace in the form of
* a wakeup event. We flag this condition for now and generate the
* event later, as we're currently too early in resume to be able to
* generate wakeup events.
*/
if (ACPI_SUCCESS(status) && (acpi_state == ACPI_STATE_S3)) {
acpi_event_status pwr_btn_status = ACPI_EVENT_FLAG_DISABLED;
acpi_get_event_status(ACPI_EVENT_POWER_BUTTON, &pwr_btn_status);
if (pwr_btn_status & ACPI_EVENT_FLAG_STATUS_SET) {
acpi_clear_event(ACPI_EVENT_POWER_BUTTON);
/* Flag for later */
pwr_btn_event_pending = true;
}
}
/*
* Disable and clear GPE status before interrupt is enabled. Some GPEs
* (like wakeup GPE) haven't handler, this can avoid such GPE misfire.
* acpi_leave_sleep_state will reenable specific GPEs later
*/
acpi_disable_all_gpes();
/* Allow EC transactions to happen. */
ACPI / EC: Add PM operations to improve event handling for resume process This patch makes 2 changes: 1. Restore old behavior Originally, EC driver stops handling both events and transactions in acpi_ec_block_transactions(), and restarts to handle transactions in acpi_ec_unblock_transactions_early(), restarts to handle both events and transactions in acpi_ec_unblock_transactions(). While currently, EC driver still stops handling both events and transactions in acpi_ec_block_transactions(), but restarts to handle both events and transactions in acpi_ec_unblock_transactions_early(). This patch tries to restore the old behavior by dropping __acpi_ec_enable_event() from acpi_unblock_transactions_early(). 2. Improve old behavior However this still cannot fix the real issue as both of the acpi_ec_unblock_xxx() functions are invoked in the noirq stage. Since the EC driver actually doesn't implement the event handling in the polling mode, re-enabling the event handling too early in the noirq stage could result in the problem that if there is no triggering source causing advance_transaction() to be invoked, pending SCI_EVT cannot be detected by the EC driver and _Qxx cannot be triggered. It actually makes sense to restart the event handling in any point during resuming after the noirq stage. Just like the boot stage where the event handling is enabled in .add(), this patch further moves acpi_ec_enable_event() to .resume(). After doing that, the following 2 functions can be combined: acpi_ec_unblock_transactions_early()/acpi_ec_unblock_transactions(). The differences of the event handling availability between the old behavior (this patch isn't applied) and the new behavior (this patch is applied) are as follows: !Applied Applied before suspend Y Y suspend before EC Y Y suspend after EC Y Y suspend_late Y Y suspend_noirq Y (actually N) Y (actually N) resume_noirq Y (actually N) Y (actually N) resume_late Y (actually N) Y (actually N) resume before EC Y (actually N) Y (actually N) resume after EC Y (actually N) Y after resume Y (actually N) Y Where "actually N" means if there is no triggering source, the EC driver is actually not able to notice the pending SCI_EVT occurred in the noirq stage. So we can clearly see that this patch has improved the situation. Signed-off-by: Lv Zheng <lv.zheng@intel.com> Tested-by: Todd E Brandt <todd.e.brandt@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-08-03 11:01:36 +03:00
acpi_ec_unblock_transactions();
suspend_nvs_restore();
return ACPI_SUCCESS(status) ? 0 : -EFAULT;
}
static int acpi_suspend_state_valid(suspend_state_t pm_state)
{
u32 acpi_state;
switch (pm_state) {
case PM_SUSPEND_ON:
case PM_SUSPEND_STANDBY:
case PM_SUSPEND_MEM:
acpi_state = acpi_suspend_states[pm_state];
return sleep_states[acpi_state];
default:
return 0;
}
}
static const struct platform_suspend_ops acpi_suspend_ops = {
.valid = acpi_suspend_state_valid,
.begin = acpi_suspend_begin,
.prepare_late = acpi_pm_prepare,
.enter = acpi_suspend_enter,
.wake = acpi_pm_finish,
.end = acpi_pm_end,
};
/**
* acpi_suspend_begin_old - Set the target system sleep state to the
* state associated with given @pm_state, if supported, and
* execute the _PTS control method. This function is used if the
* pre-ACPI 2.0 suspend ordering has been requested.
*/
static int acpi_suspend_begin_old(suspend_state_t pm_state)
{
int error = acpi_suspend_begin(pm_state);
if (!error)
error = __acpi_pm_prepare();
return error;
}
/*
* The following callbacks are used if the pre-ACPI 2.0 suspend ordering has
* been requested.
*/
static const struct platform_suspend_ops acpi_suspend_ops_old = {
.valid = acpi_suspend_state_valid,
.begin = acpi_suspend_begin_old,
.prepare_late = acpi_pm_pre_suspend,
.enter = acpi_suspend_enter,
.wake = acpi_pm_finish,
.end = acpi_pm_end,
.recover = acpi_pm_finish,
};
ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle The ACPI SCI (System Control Interrupt) is set up as a wakeup IRQ during suspend-to-idle transitions and, consequently, any events signaled through it wake up the system from that state. However, on some systems some of the events signaled via the ACPI SCI while suspended to idle should not cause the system to wake up. In fact, quite often they should just be discarded. Arguably, systems should not resume entirely on such events, but in order to decide which events really should cause the system to resume and which are spurious, it is necessary to resume up to the point when ACPI SCIs are actually handled and processed, which is after executing dpm_resume_noirq() in the system resume path. For this reasons, add a loop around freeze_enter() in which the platforms can process events signaled via multiplexed IRQ lines like the ACPI SCI and add suspend-to-idle hooks that can be used for this purpose to struct platform_freeze_ops. In the ACPI case, the ->wake hook is used for checking if the SCI has triggered while suspended and deferring the interrupt-induced system wakeup until the events signaled through it are actually processed sufficiently to decide whether or not the system should resume. In turn, the ->sync hook allows all of the relevant event queues to be flushed so as to prevent events from being missed due to race conditions. In addition to that, some ACPI code processing wakeup events needs to be modified to use the "hard" version of wakeup triggers, so that it will cause a system resume to happen on device-induced wakeup events even if the "soft" mechanism to prevent the system from suspending is not enabled. However, to preserve the existing behavior with respect to suspend-to-RAM, this only is done in the suspend-to-idle case and only if an SCI has occurred while suspended. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-06-12 23:56:34 +03:00
static bool s2idle_wakeup;
int acpi_s2idle_begin(void)
{
acpi_scan_lock_acquire();
return 0;
}
int acpi_s2idle_prepare(void)
{
if (acpi_sci_irq_valid()) {
enable_irq_wake(acpi_sci_irq);
acpi_ec_set_gpe_wake_mask(ACPI_GPE_ENABLE);
}
ACPI: PM: Set enable_for_wake for wakeup GPEs during suspend-to-idle I noticed that recently multiple systems (chromebooks) couldn't wake from S0ix using LID or Keyboard after updating to a newer kernel. I bisected and it turned up commit f941d3e41da7 ("ACPI: EC / PM: Disable non-wakeup GPEs for suspend-to-idle"). I checked that the issue got fixed if that commit was reverted. I debugged and found that although PNP0C0D:00 (representing the LID) is wake capable and should wakeup the system per the code in acpi_wakeup_gpe_init() and in drivers/acpi/button.c: localhost /sys # cat /proc/acpi/wakeup Device S-state Status Sysfs node LID0 S4 *enabled platform:PNP0C0D:00 CREC S5 *disabled platform:GOOG0004:00 *disabled platform:cros-ec-dev.1.auto *disabled platform:cros-ec-accel.0 *disabled platform:cros-ec-accel.1 *disabled platform:cros-ec-gyro.0 *disabled platform:cros-ec-ring.0 *disabled platform:cros-usbpd-charger.2.auto *disabled platform:cros-usbpd-logger.3.auto D015 S3 *enabled i2c:i2c-ELAN0000:00 PENH S3 *enabled platform:PRP0001:00 XHCI S3 *enabled pci:0000:00:14.0 GLAN S4 *disabled WIFI S3 *disabled pci:0000:00:14.3 localhost /sys # On debugging, I found that its corresponding GPE is not being enabled. The particular GPE's "gpe_register_info->enable_for_wake" does not have any bits set when acpi_enable_all_wakeup_gpes() comes around to use it. I looked at code and could not find any other code path that should set the bits in "enable_for_wake" bitmask for the wake enabled devices for s2idle. [I do see that it happens for S3 in acpi_sleep_prepare()]. Thus I used the same call to enable the GPEs for wake enabled devices, and verified that this fixes the regression I was seeing on multiple of my devices. [ rjw: The problem is that commit f941d3e41da7 ("ACPI: EC / PM: Disable non-wakeup GPEs for suspend-to-idle") forgot to add the acpi_enable_wakeup_devices() call for s2idle along with acpi_enable_all_wakeup_gpes(). ] Fixes: f941d3e41da7 ("ACPI: EC / PM: Disable non-wakeup GPEs for suspend-to-idle") Link: https://bugzilla.kernel.org/show_bug.cgi?id=203579 Signed-off-by: Rajat Jain <rajatja@google.com> [ rjw: Subject & changelog ] Cc: 5.0+ <stable@vger.kernel.org> # 5.0+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2019-05-13 22:17:08 +03:00
acpi_enable_wakeup_devices(ACPI_STATE_S0);
/* Change the configuration of GPEs to avoid spurious wakeup. */
acpi_enable_all_wakeup_gpes();
acpi_os_wait_events_complete();
s2idle_wakeup = true;
return 0;
}
bool acpi_s2idle_wake(void)
ACPI: PM: s2idle: Execute LPS0 _DSM functions with suspended devices According to Section 3.5 of the "Intel Low Power S0 Idle" document [1], Function 5 of the LPS0 _DSM is expected to be invoked when the system configuration matches the criteria for entering the target low-power state of the platform. In particular, this means that all devices should be suspended and in low-power states already when that function is invoked. This is not the case currently, however, because Function 5 of the LPS0 _DSM is invoked by it before the "noirq" phase of device suspend, which means that some devices may not have been put into low-power states yet at that point. That is a consequence of the previous design of the suspend-to-idle flow that allowed the "noirq" phase of device suspend and the "noirq" phase of device resume to be carried out for multiple times while "suspended" (if any spurious wakeup events were detected) and the point of the LPS0 _DSM Function 5 invocation was chosen so as to call it (and LPS0 _DSM Function 6 analogously) once per suspend-resume cycle (regardless of how many times the "noirq" phases of device suspend and resume were carried out while "suspended"). Now that the suspend-to-idle flow has been redesigned to carry out the "noirq" phases of device suspend and resume once in each cycle, the code can be reordered to follow the specification that it is based on more closely. For this purpose, add ->prepare_late and ->restore_early platform callbacks for suspend-to-idle, to be executed, respectively, after the "noirq" phase of suspending devices and before the "noirq" phase of resuming them and make ACPI use them for the invocation of LPS0 _DSM functions as appropriate. While at it, move the LPS0 entry requirements check to be made before invoking Functions 3 and 5 of the LPS0 _DSM (also once per cycle) as follows from the specification [1]. Link: https://uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf # [1] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
2019-08-01 20:31:10 +03:00
{
if (!acpi_sci_irq_valid())
return pm_wakeup_pending();
while (pm_wakeup_pending()) {
/*
* If IRQD_WAKEUP_ARMED is set for the SCI at this point, the
* SCI has not triggered while suspended, so bail out (the
* wakeup is pending anyway and the SCI is not the source of
* it).
*/
if (irqd_is_wakeup_armed(irq_get_irq_data(acpi_sci_irq))) {
pm_pr_dbg("Wakeup unrelated to ACPI SCI\n");
return true;
}
/*
* If the status bit of any enabled fixed event is set, the
* wakeup is regarded as valid.
*/
if (acpi_any_fixed_event_status_set()) {
pm_pr_dbg("ACPI fixed event wakeup\n");
return true;
}
ACPI: PM: Add acpi_[un]register_wakeup_handler() Since commit fdde0ff8590b ("ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system") the SCI triggering without there being a wakeup cause recognized by the ACPI sleep code will no longer wakeup the system. This works as intended, but this is a problem for devices where the SCI is shared with another device which is also a wakeup source. In the past these, from the pov of the ACPI sleep code, spurious SCIs would still cause a wakeup so the wakeup from the device sharing the interrupt would actually wakeup the system. This now no longer works. This is a problem on e.g. Bay Trail-T and Cherry Trail devices where some peripherals (typically the XHCI controller) can signal a Power Management Event (PME) to the Power Management Controller (PMC) to wakeup the system, this uses the same interrupt as the SCI. These wakeups are handled through a special INT0002 ACPI device which checks for events in the GPE0a_STS for this and takes care of acking the PME so that the shared interrupt stops triggering. The change to the ACPI sleep code to ignore the spurious SCI, causes the system to no longer wakeup on these PME events. To make things worse this means that the INT0002 device driver interrupt handler will no longer run, causing the PME to not get cleared and resulting in the system hanging. Trying to wakeup the system after such a PME through e.g. the power button no longer works. Add an acpi_register_wakeup_handler() function which registers a handler to be called from acpi_s2idle_wake() and when the handler returns true, return true from acpi_s2idle_wake(). The INT0002 driver will use this mechanism to check the GPE0a_STS register from acpi_s2idle_wake() and to tell the system to wakeup if a PME is signaled in the register. Fixes: fdde0ff8590b ("ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system") Cc: 5.4+ <stable@vger.kernel.org> # 5.4+ Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-04-03 18:48:33 +03:00
/* Check wakeups from drivers sharing the SCI. */
if (acpi_check_wakeup_handlers()) {
pm_pr_dbg("ACPI custom handler wakeup\n");
ACPI: PM: Add acpi_[un]register_wakeup_handler() Since commit fdde0ff8590b ("ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system") the SCI triggering without there being a wakeup cause recognized by the ACPI sleep code will no longer wakeup the system. This works as intended, but this is a problem for devices where the SCI is shared with another device which is also a wakeup source. In the past these, from the pov of the ACPI sleep code, spurious SCIs would still cause a wakeup so the wakeup from the device sharing the interrupt would actually wakeup the system. This now no longer works. This is a problem on e.g. Bay Trail-T and Cherry Trail devices where some peripherals (typically the XHCI controller) can signal a Power Management Event (PME) to the Power Management Controller (PMC) to wakeup the system, this uses the same interrupt as the SCI. These wakeups are handled through a special INT0002 ACPI device which checks for events in the GPE0a_STS for this and takes care of acking the PME so that the shared interrupt stops triggering. The change to the ACPI sleep code to ignore the spurious SCI, causes the system to no longer wakeup on these PME events. To make things worse this means that the INT0002 device driver interrupt handler will no longer run, causing the PME to not get cleared and resulting in the system hanging. Trying to wakeup the system after such a PME through e.g. the power button no longer works. Add an acpi_register_wakeup_handler() function which registers a handler to be called from acpi_s2idle_wake() and when the handler returns true, return true from acpi_s2idle_wake(). The INT0002 driver will use this mechanism to check the GPE0a_STS register from acpi_s2idle_wake() and to tell the system to wakeup if a PME is signaled in the register. Fixes: fdde0ff8590b ("ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system") Cc: 5.4+ <stable@vger.kernel.org> # 5.4+ Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-04-03 18:48:33 +03:00
return true;
}
ACPI: PM: Add acpi_[un]register_wakeup_handler() Since commit fdde0ff8590b ("ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system") the SCI triggering without there being a wakeup cause recognized by the ACPI sleep code will no longer wakeup the system. This works as intended, but this is a problem for devices where the SCI is shared with another device which is also a wakeup source. In the past these, from the pov of the ACPI sleep code, spurious SCIs would still cause a wakeup so the wakeup from the device sharing the interrupt would actually wakeup the system. This now no longer works. This is a problem on e.g. Bay Trail-T and Cherry Trail devices where some peripherals (typically the XHCI controller) can signal a Power Management Event (PME) to the Power Management Controller (PMC) to wakeup the system, this uses the same interrupt as the SCI. These wakeups are handled through a special INT0002 ACPI device which checks for events in the GPE0a_STS for this and takes care of acking the PME so that the shared interrupt stops triggering. The change to the ACPI sleep code to ignore the spurious SCI, causes the system to no longer wakeup on these PME events. To make things worse this means that the INT0002 device driver interrupt handler will no longer run, causing the PME to not get cleared and resulting in the system hanging. Trying to wakeup the system after such a PME through e.g. the power button no longer works. Add an acpi_register_wakeup_handler() function which registers a handler to be called from acpi_s2idle_wake() and when the handler returns true, return true from acpi_s2idle_wake(). The INT0002 driver will use this mechanism to check the GPE0a_STS register from acpi_s2idle_wake() and to tell the system to wakeup if a PME is signaled in the register. Fixes: fdde0ff8590b ("ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system") Cc: 5.4+ <stable@vger.kernel.org> # 5.4+ Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-04-03 18:48:33 +03:00
ACPI: EC: PM: Avoid premature returns from acpi_s2idle_wake() If the EC GPE status is not set after checking all of the other GPEs, acpi_s2idle_wake() returns 'false', to indicate that the SCI event that has just triggered is not a system wakeup one, but it does that without canceling the pending wakeup and re-arming the SCI for system wakeup which is a mistake, because it may cause s2idle_loop() to busy spin until the next valid wakeup event. [If that happens, the first spurious wakeup is still pending after acpi_s2idle_wake() has returned, so s2idle_enter() does nothing, acpi_s2idle_wake() is called again and it sees that the SCI has triggered, but no GPEs are active, so 'false' is returned again, and so on.] Fix that by moving all of the GPE checking logic from acpi_s2idle_wake() to acpi_ec_dispatch_gpe() and making the latter return 'true' only if a non-EC GPE has triggered and 'false' otherwise, which will cause acpi_s2idle_wake() to cancel the pending SCI wakeup and re-arm the SCI for system wakeup regardless of the EC GPE status. This also addresses a lockup observed on an Elitegroup EF20EA laptop after attempting to wake it up from suspend-to-idle by a key press. Fixes: d5406284ff80 ("ACPI: PM: s2idle: Refine active GPEs check") Link: https://bugzilla.kernel.org/show_bug.cgi?id=207603 Reported-by: Todd Brandt <todd.e.brandt@linux.intel.com> Fixes: fdde0ff8590b ("ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system") Link: https://lore.kernel.org/linux-acpi/CAB4CAwdqo7=MvyG_PE+PGVfeA17AHF5i5JucgaKqqMX6mjArbQ@mail.gmail.com/ Reported-by: Chris Chiu <chiu@endlessm.com> Tested-by: Chris Chiu <chiu@endlessm.com> Cc: 5.4+ <stable@vger.kernel.org> # 5.4+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-05-09 11:44:41 +03:00
/* Check non-EC GPE wakeups and dispatch the EC GPE. */
if (acpi_ec_dispatch_gpe()) {
pm_pr_dbg("ACPI non-EC GPE wakeup\n");
return true;
}
PM: sleep: Simplify suspend-to-idle control flow After commit 33e4f80ee69b ("ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle") the "noirq" phases of device suspend and resume may run for multiple times during suspend-to-idle, if there are spurious system wakeup events while suspended. However, this is complicated and fragile and actually unnecessary. The main reason for doing this is that on some systems the EC may signal system wakeup events (power button events, for example) as well as events that should not cause the system to resume (spurious system wakeup events). Thus, in order to determine whether or not a given event signaled by the EC while suspended is a proper system wakeup one, the EC GPE needs to be dispatched and to start with that was achieved by allowing the ACPI SCI action handler to run, which was only possible after calling resume_device_irqs(). However, dispatching the EC GPE this way turned out to take too much time in some cases and some EC events might be missed due to that, so commit 68e22011856f ("ACPI: EC: Dispatch the EC GPE directly on s2idle wake") started to dispatch the EC GPE right after a wakeup event has been detected, so in fact the full ACPI SCI action handler doesn't need to run any more to deal with the wakeups coming from the EC. Use this observation to simplify the suspend-to-idle control flow so that the "noirq" phases of device suspend and resume are each run only once in every suspend-to-idle cycle, which is reported to significantly reduce power drawn by some systems when suspended to idle (by allowing them to reach a deep platform-wide low-power state through the suspend-to-idle flow). [What appears to happen is that the "noirq" resume of devices after a spurious EC wakeup brings some devices into a state in which they prevent the platform from reaching the deep low-power state going forward, even after a subsequent "noirq" suspend phase, and on some systems the EC triggers such wakeups already when the "noirq" suspend of devices is running for the first time in the given suspend/resume cycle, so the platform cannot reach the deep low-power state at all.] First, make acpi_s2idle_wake() use the acpi_ec_dispatch_gpe() return value to determine whether or not the wakeup may have been triggered by the EC (in which case the system wakeup is canceled and ACPI events are processed in order to determine whether or not the event is a proper system wakeup one) and use rearm_wake_irq() (introduced by a previous change) in it to rearm the ACPI SCI for system wakeup detection in case the system will remain suspended. Second, drop acpi_s2idle_sync(), which is not needed any more, and the corresponding global platform suspend-to-idle callback. Next, drop the pm_wakeup_pending() check (which is an optimization only) from __device_suspend_noirq() to prevent it from returning errors on system wakeups occurring before the "noirq" phase of device suspend is complete (as in the case of suspend-to-idle it is not known whether or not these wakeups are suprious at that point), in order to avoid having to carry out a "noirq" resume of devices on a spurious system wakeup. Finally, change the code flow in s2idle_loop() to (1) run the "noirq" suspend of devices once before starting the loop, (2) check for spurious EC wakeups (via the platform ->wake callback) for the first time before calling s2idle_enter(), and (3) run the "noirq" resume of devices once after leaving the loop. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Thomas Gleixner <tglx@linutronix.de>
2019-07-16 00:52:03 +03:00
/*
* Cancel the SCI wakeup and process all pending events in case
PM: sleep: Simplify suspend-to-idle control flow After commit 33e4f80ee69b ("ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle") the "noirq" phases of device suspend and resume may run for multiple times during suspend-to-idle, if there are spurious system wakeup events while suspended. However, this is complicated and fragile and actually unnecessary. The main reason for doing this is that on some systems the EC may signal system wakeup events (power button events, for example) as well as events that should not cause the system to resume (spurious system wakeup events). Thus, in order to determine whether or not a given event signaled by the EC while suspended is a proper system wakeup one, the EC GPE needs to be dispatched and to start with that was achieved by allowing the ACPI SCI action handler to run, which was only possible after calling resume_device_irqs(). However, dispatching the EC GPE this way turned out to take too much time in some cases and some EC events might be missed due to that, so commit 68e22011856f ("ACPI: EC: Dispatch the EC GPE directly on s2idle wake") started to dispatch the EC GPE right after a wakeup event has been detected, so in fact the full ACPI SCI action handler doesn't need to run any more to deal with the wakeups coming from the EC. Use this observation to simplify the suspend-to-idle control flow so that the "noirq" phases of device suspend and resume are each run only once in every suspend-to-idle cycle, which is reported to significantly reduce power drawn by some systems when suspended to idle (by allowing them to reach a deep platform-wide low-power state through the suspend-to-idle flow). [What appears to happen is that the "noirq" resume of devices after a spurious EC wakeup brings some devices into a state in which they prevent the platform from reaching the deep low-power state going forward, even after a subsequent "noirq" suspend phase, and on some systems the EC triggers such wakeups already when the "noirq" suspend of devices is running for the first time in the given suspend/resume cycle, so the platform cannot reach the deep low-power state at all.] First, make acpi_s2idle_wake() use the acpi_ec_dispatch_gpe() return value to determine whether or not the wakeup may have been triggered by the EC (in which case the system wakeup is canceled and ACPI events are processed in order to determine whether or not the event is a proper system wakeup one) and use rearm_wake_irq() (introduced by a previous change) in it to rearm the ACPI SCI for system wakeup detection in case the system will remain suspended. Second, drop acpi_s2idle_sync(), which is not needed any more, and the corresponding global platform suspend-to-idle callback. Next, drop the pm_wakeup_pending() check (which is an optimization only) from __device_suspend_noirq() to prevent it from returning errors on system wakeups occurring before the "noirq" phase of device suspend is complete (as in the case of suspend-to-idle it is not known whether or not these wakeups are suprious at that point), in order to avoid having to carry out a "noirq" resume of devices on a spurious system wakeup. Finally, change the code flow in s2idle_loop() to (1) run the "noirq" suspend of devices once before starting the loop, (2) check for spurious EC wakeups (via the platform ->wake callback) for the first time before calling s2idle_enter(), and (3) run the "noirq" resume of devices once after leaving the loop. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Thomas Gleixner <tglx@linutronix.de>
2019-07-16 00:52:03 +03:00
* there are any wakeup ones in there.
*
* Note that if any non-EC GPEs are active at this point, the
* SCI will retrigger after the rearming below, so no events
* should be missed by canceling the wakeup here.
*/
ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle The ACPI SCI (System Control Interrupt) is set up as a wakeup IRQ during suspend-to-idle transitions and, consequently, any events signaled through it wake up the system from that state. However, on some systems some of the events signaled via the ACPI SCI while suspended to idle should not cause the system to wake up. In fact, quite often they should just be discarded. Arguably, systems should not resume entirely on such events, but in order to decide which events really should cause the system to resume and which are spurious, it is necessary to resume up to the point when ACPI SCIs are actually handled and processed, which is after executing dpm_resume_noirq() in the system resume path. For this reasons, add a loop around freeze_enter() in which the platforms can process events signaled via multiplexed IRQ lines like the ACPI SCI and add suspend-to-idle hooks that can be used for this purpose to struct platform_freeze_ops. In the ACPI case, the ->wake hook is used for checking if the SCI has triggered while suspended and deferring the interrupt-induced system wakeup until the events signaled through it are actually processed sufficiently to decide whether or not the system should resume. In turn, the ->sync hook allows all of the relevant event queues to be flushed so as to prevent events from being missed due to race conditions. In addition to that, some ACPI code processing wakeup events needs to be modified to use the "hard" version of wakeup triggers, so that it will cause a system resume to happen on device-induced wakeup events even if the "soft" mechanism to prevent the system from suspending is not enabled. However, to preserve the existing behavior with respect to suspend-to-RAM, this only is done in the suspend-to-idle case and only if an SCI has occurred while suspended. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-06-12 23:56:34 +03:00
pm_system_cancel_wakeup();
acpi_os_wait_events_complete();
ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle The ACPI SCI (System Control Interrupt) is set up as a wakeup IRQ during suspend-to-idle transitions and, consequently, any events signaled through it wake up the system from that state. However, on some systems some of the events signaled via the ACPI SCI while suspended to idle should not cause the system to wake up. In fact, quite often they should just be discarded. Arguably, systems should not resume entirely on such events, but in order to decide which events really should cause the system to resume and which are spurious, it is necessary to resume up to the point when ACPI SCIs are actually handled and processed, which is after executing dpm_resume_noirq() in the system resume path. For this reasons, add a loop around freeze_enter() in which the platforms can process events signaled via multiplexed IRQ lines like the ACPI SCI and add suspend-to-idle hooks that can be used for this purpose to struct platform_freeze_ops. In the ACPI case, the ->wake hook is used for checking if the SCI has triggered while suspended and deferring the interrupt-induced system wakeup until the events signaled through it are actually processed sufficiently to decide whether or not the system should resume. In turn, the ->sync hook allows all of the relevant event queues to be flushed so as to prevent events from being missed due to race conditions. In addition to that, some ACPI code processing wakeup events needs to be modified to use the "hard" version of wakeup triggers, so that it will cause a system resume to happen on device-induced wakeup events even if the "soft" mechanism to prevent the system from suspending is not enabled. However, to preserve the existing behavior with respect to suspend-to-RAM, this only is done in the suspend-to-idle case and only if an SCI has occurred while suspended. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-06-12 23:56:34 +03:00
/*
* The SCI is in the "suspended" state now and it cannot produce
* new wakeup events till the rearming below, so if any of them
* are pending here, they must be resulting from the processing
* of EC events above or coming from somewhere else.
*/
if (pm_wakeup_pending()) {
pm_pr_dbg("Wakeup after ACPI Notify sync\n");
return true;
}
rearm_wake_irq(acpi_sci_irq);
}
return false;
ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle The ACPI SCI (System Control Interrupt) is set up as a wakeup IRQ during suspend-to-idle transitions and, consequently, any events signaled through it wake up the system from that state. However, on some systems some of the events signaled via the ACPI SCI while suspended to idle should not cause the system to wake up. In fact, quite often they should just be discarded. Arguably, systems should not resume entirely on such events, but in order to decide which events really should cause the system to resume and which are spurious, it is necessary to resume up to the point when ACPI SCIs are actually handled and processed, which is after executing dpm_resume_noirq() in the system resume path. For this reasons, add a loop around freeze_enter() in which the platforms can process events signaled via multiplexed IRQ lines like the ACPI SCI and add suspend-to-idle hooks that can be used for this purpose to struct platform_freeze_ops. In the ACPI case, the ->wake hook is used for checking if the SCI has triggered while suspended and deferring the interrupt-induced system wakeup until the events signaled through it are actually processed sufficiently to decide whether or not the system should resume. In turn, the ->sync hook allows all of the relevant event queues to be flushed so as to prevent events from being missed due to race conditions. In addition to that, some ACPI code processing wakeup events needs to be modified to use the "hard" version of wakeup triggers, so that it will cause a system resume to happen on device-induced wakeup events even if the "soft" mechanism to prevent the system from suspending is not enabled. However, to preserve the existing behavior with respect to suspend-to-RAM, this only is done in the suspend-to-idle case and only if an SCI has occurred while suspended. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-06-12 23:56:34 +03:00
}
void acpi_s2idle_restore(void)
{
/*
* Drain pending events before restoring the working-state configuration
* of GPEs.
*/
acpi_os_wait_events_complete(); /* synchronize GPE processing */
acpi_ec_flush_work(); /* flush the EC driver's workqueues */
acpi_os_wait_events_complete(); /* synchronize Notify handling */
s2idle_wakeup = false;
acpi_enable_all_runtime_gpes();
ACPI: PM: Set enable_for_wake for wakeup GPEs during suspend-to-idle I noticed that recently multiple systems (chromebooks) couldn't wake from S0ix using LID or Keyboard after updating to a newer kernel. I bisected and it turned up commit f941d3e41da7 ("ACPI: EC / PM: Disable non-wakeup GPEs for suspend-to-idle"). I checked that the issue got fixed if that commit was reverted. I debugged and found that although PNP0C0D:00 (representing the LID) is wake capable and should wakeup the system per the code in acpi_wakeup_gpe_init() and in drivers/acpi/button.c: localhost /sys # cat /proc/acpi/wakeup Device S-state Status Sysfs node LID0 S4 *enabled platform:PNP0C0D:00 CREC S5 *disabled platform:GOOG0004:00 *disabled platform:cros-ec-dev.1.auto *disabled platform:cros-ec-accel.0 *disabled platform:cros-ec-accel.1 *disabled platform:cros-ec-gyro.0 *disabled platform:cros-ec-ring.0 *disabled platform:cros-usbpd-charger.2.auto *disabled platform:cros-usbpd-logger.3.auto D015 S3 *enabled i2c:i2c-ELAN0000:00 PENH S3 *enabled platform:PRP0001:00 XHCI S3 *enabled pci:0000:00:14.0 GLAN S4 *disabled WIFI S3 *disabled pci:0000:00:14.3 localhost /sys # On debugging, I found that its corresponding GPE is not being enabled. The particular GPE's "gpe_register_info->enable_for_wake" does not have any bits set when acpi_enable_all_wakeup_gpes() comes around to use it. I looked at code and could not find any other code path that should set the bits in "enable_for_wake" bitmask for the wake enabled devices for s2idle. [I do see that it happens for S3 in acpi_sleep_prepare()]. Thus I used the same call to enable the GPEs for wake enabled devices, and verified that this fixes the regression I was seeing on multiple of my devices. [ rjw: The problem is that commit f941d3e41da7 ("ACPI: EC / PM: Disable non-wakeup GPEs for suspend-to-idle") forgot to add the acpi_enable_wakeup_devices() call for s2idle along with acpi_enable_all_wakeup_gpes(). ] Fixes: f941d3e41da7 ("ACPI: EC / PM: Disable non-wakeup GPEs for suspend-to-idle") Link: https://bugzilla.kernel.org/show_bug.cgi?id=203579 Signed-off-by: Rajat Jain <rajatja@google.com> [ rjw: Subject & changelog ] Cc: 5.0+ <stable@vger.kernel.org> # 5.0+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2019-05-13 22:17:08 +03:00
acpi_disable_wakeup_devices(ACPI_STATE_S0);
if (acpi_sci_irq_valid()) {
acpi_ec_set_gpe_wake_mask(ACPI_GPE_DISABLE);
disable_irq_wake(acpi_sci_irq);
}
}
void acpi_s2idle_end(void)
{
acpi_scan_lock_release();
}
static const struct platform_s2idle_ops acpi_s2idle_ops = {
.begin = acpi_s2idle_begin,
.prepare = acpi_s2idle_prepare,
.wake = acpi_s2idle_wake,
.restore = acpi_s2idle_restore,
.end = acpi_s2idle_end,
};
void __weak acpi_s2idle_setup(void)
{
s2idle_set_ops(&acpi_s2idle_ops);
}
static void acpi_sleep_suspend_setup(void)
{
int i;
for (i = ACPI_STATE_S1; i < ACPI_STATE_S4; i++)
if (acpi_sleep_state_supported(i))
sleep_states[i] = 1;
suspend_set_ops(old_suspend_ordering ?
&acpi_suspend_ops_old : &acpi_suspend_ops);
ACPI / sleep: EC-based wakeup from suspend-to-idle on recent systems Some recent Dell laptops, including the XPS13 model numbers 9360 and 9365, cannot be woken up from suspend-to-idle by pressing the power button which is unexpected and makes that feature less usable on those systems. Moreover, on the 9365 ACPI S3 (suspend-to-RAM) is not expected to be used at all (the OS these systems ship with never exercises the ACPI S3 path in the firmware) and suspend-to-idle is the only viable system suspend mechanism there. The reason why the power button wakeup from suspend-to-idle doesn't work on those systems is because their power button events are signaled by the EC (Embedded Controller), whose GPE (General Purpose Event) line is disabled during suspend-to-idle transitions in Linux. That is done on purpose, because in general the EC tends to be noisy for various reasons (battery and thermal updates and similar, for example) and all events signaled by it would kick the CPUs out of deep idle states while in suspend-to-idle, which effectively might defeat its purpose. Of course, on the Dell systems in question the EC GPE must be enabled during suspend-to-idle transitions for the button press events to be signaled while suspended at all, but fortunately there is a way out of this puzzle. First of all, those systems have the ACPI_FADT_LOW_POWER_S0 flag set in their ACPI tables, which means that the OS is expected to prefer the "low power S0 idle" system state over ACPI S3 on them. That causes the most recent versions of other OSes to simply ignore ACPI S3 on those systems, so it is reasonable to expect that it should not be necessary to block GPEs during suspend-to-idle on them. Second, in addition to that, the systems in question provide a special firmware interface that can be used to indicate to the platform that the OS is transitioning into a system-wide low-power state in which certain types of activity are not desirable or that it is leaving such a state and that (in principle) should allow the platform to adjust its operation mode accordingly. That interface is a special _DSM object under a System Power Management Controller device (PNP0D80). The expected way to use it is to invoke function 0 from it on system initialization, functions 3 and 5 during suspend transitions and functions 4 and 6 during resume transitions (to reverse the actions carried out by the former). In particular, function 5 from the "Low-Power S0" device _DSM is expected to cause the platform to put itself into a low-power operation mode which should include making the EC less verbose (so to speak). Next, on resume, function 6 switches the platform back to the "working-state" operation mode. In accordance with the above, modify the ACPI suspend-to-idle code to look for the "Low-Power S0" _DSM interface on platforms with the ACPI_FADT_LOW_POWER_S0 flag set in the ACPI tables. If it's there, use it during suspend-to-idle transitions as prescribed and avoid changing the GPE configuration in that case. [That should reflect what the most recent versions of other OSes do.] Also modify the ACPI EC driver to make it handle events during suspend-to-idle in the usual way if the "Low-Power S0" _DSM interface is going to be used to make the power button events work while suspended on the Dell machines mentioned above Link: http://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-06-23 16:24:32 +03:00
acpi_s2idle_setup();
}
#else /* !CONFIG_SUSPEND */
ACPI / sleep: EC-based wakeup from suspend-to-idle on recent systems Some recent Dell laptops, including the XPS13 model numbers 9360 and 9365, cannot be woken up from suspend-to-idle by pressing the power button which is unexpected and makes that feature less usable on those systems. Moreover, on the 9365 ACPI S3 (suspend-to-RAM) is not expected to be used at all (the OS these systems ship with never exercises the ACPI S3 path in the firmware) and suspend-to-idle is the only viable system suspend mechanism there. The reason why the power button wakeup from suspend-to-idle doesn't work on those systems is because their power button events are signaled by the EC (Embedded Controller), whose GPE (General Purpose Event) line is disabled during suspend-to-idle transitions in Linux. That is done on purpose, because in general the EC tends to be noisy for various reasons (battery and thermal updates and similar, for example) and all events signaled by it would kick the CPUs out of deep idle states while in suspend-to-idle, which effectively might defeat its purpose. Of course, on the Dell systems in question the EC GPE must be enabled during suspend-to-idle transitions for the button press events to be signaled while suspended at all, but fortunately there is a way out of this puzzle. First of all, those systems have the ACPI_FADT_LOW_POWER_S0 flag set in their ACPI tables, which means that the OS is expected to prefer the "low power S0 idle" system state over ACPI S3 on them. That causes the most recent versions of other OSes to simply ignore ACPI S3 on those systems, so it is reasonable to expect that it should not be necessary to block GPEs during suspend-to-idle on them. Second, in addition to that, the systems in question provide a special firmware interface that can be used to indicate to the platform that the OS is transitioning into a system-wide low-power state in which certain types of activity are not desirable or that it is leaving such a state and that (in principle) should allow the platform to adjust its operation mode accordingly. That interface is a special _DSM object under a System Power Management Controller device (PNP0D80). The expected way to use it is to invoke function 0 from it on system initialization, functions 3 and 5 during suspend transitions and functions 4 and 6 during resume transitions (to reverse the actions carried out by the former). In particular, function 5 from the "Low-Power S0" device _DSM is expected to cause the platform to put itself into a low-power operation mode which should include making the EC less verbose (so to speak). Next, on resume, function 6 switches the platform back to the "working-state" operation mode. In accordance with the above, modify the ACPI suspend-to-idle code to look for the "Low-Power S0" _DSM interface on platforms with the ACPI_FADT_LOW_POWER_S0 flag set in the ACPI tables. If it's there, use it during suspend-to-idle transitions as prescribed and avoid changing the GPE configuration in that case. [That should reflect what the most recent versions of other OSes do.] Also modify the ACPI EC driver to make it handle events during suspend-to-idle in the usual way if the "Low-Power S0" _DSM interface is going to be used to make the power button events work while suspended on the Dell machines mentioned above Link: http://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-06-23 16:24:32 +03:00
#define s2idle_wakeup (false)
static inline void acpi_sleep_suspend_setup(void) {}
#endif /* !CONFIG_SUSPEND */
ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle The ACPI SCI (System Control Interrupt) is set up as a wakeup IRQ during suspend-to-idle transitions and, consequently, any events signaled through it wake up the system from that state. However, on some systems some of the events signaled via the ACPI SCI while suspended to idle should not cause the system to wake up. In fact, quite often they should just be discarded. Arguably, systems should not resume entirely on such events, but in order to decide which events really should cause the system to resume and which are spurious, it is necessary to resume up to the point when ACPI SCIs are actually handled and processed, which is after executing dpm_resume_noirq() in the system resume path. For this reasons, add a loop around freeze_enter() in which the platforms can process events signaled via multiplexed IRQ lines like the ACPI SCI and add suspend-to-idle hooks that can be used for this purpose to struct platform_freeze_ops. In the ACPI case, the ->wake hook is used for checking if the SCI has triggered while suspended and deferring the interrupt-induced system wakeup until the events signaled through it are actually processed sufficiently to decide whether or not the system should resume. In turn, the ->sync hook allows all of the relevant event queues to be flushed so as to prevent events from being missed due to race conditions. In addition to that, some ACPI code processing wakeup events needs to be modified to use the "hard" version of wakeup triggers, so that it will cause a system resume to happen on device-induced wakeup events even if the "soft" mechanism to prevent the system from suspending is not enabled. However, to preserve the existing behavior with respect to suspend-to-RAM, this only is done in the suspend-to-idle case and only if an SCI has occurred while suspended. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-06-12 23:56:34 +03:00
bool acpi_s2idle_wakeup(void)
{
return s2idle_wakeup;
}
#ifdef CONFIG_PM_SLEEP
static u32 saved_bm_rld;
static int acpi_save_bm_rld(void)
{
acpi_read_bit_register(ACPI_BITREG_BUS_MASTER_RLD, &saved_bm_rld);
return 0;
}
static void acpi_restore_bm_rld(void)
{
u32 resumed_bm_rld = 0;
acpi_read_bit_register(ACPI_BITREG_BUS_MASTER_RLD, &resumed_bm_rld);
if (resumed_bm_rld == saved_bm_rld)
return;
acpi_write_bit_register(ACPI_BITREG_BUS_MASTER_RLD, saved_bm_rld);
}
static struct syscore_ops acpi_sleep_syscore_ops = {
.suspend = acpi_save_bm_rld,
.resume = acpi_restore_bm_rld,
};
static void acpi_sleep_syscore_init(void)
{
register_syscore_ops(&acpi_sleep_syscore_ops);
}
#else
static inline void acpi_sleep_syscore_init(void) {}
#endif /* CONFIG_PM_SLEEP */
#ifdef CONFIG_HIBERNATION
static unsigned long s4_hardware_signature;
static struct acpi_table_facs *facs;
static bool nosigcheck;
void __init acpi_no_s4_hw_signature(void)
{
nosigcheck = true;
}
static int acpi_hibernation_begin(pm_message_t stage)
{
if (!nvs_nosave) {
int error = suspend_nvs_alloc();
if (error)
return error;
}
if (stage.event == PM_EVENT_HIBERNATE)
pm_set_suspend_via_firmware();
acpi_pm_start(ACPI_STATE_S4);
return 0;
}
static int acpi_hibernation_enter(void)
{
acpi_status status = AE_OK;
ACPI_FLUSH_CPU_CACHE();
/* This shouldn't return. If it returns, we have a problem */
status = acpi_enter_sleep_state(ACPI_STATE_S4);
/* Reprogram control registers */
acpi_leave_sleep_state_prep(ACPI_STATE_S4);
return ACPI_SUCCESS(status) ? 0 : -EFAULT;
}
static void acpi_hibernation_leave(void)
{
pm_set_resume_via_firmware();
/*
* If ACPI is not enabled by the BIOS and the boot kernel, we need to
* enable it here.
*/
acpi_enable();
/* Reprogram control registers */
acpi_leave_sleep_state_prep(ACPI_STATE_S4);
/* Check the hardware signature */
if (facs && s4_hardware_signature != facs->hardware_signature)
pr_crit("Hardware changed while hibernated, success doubtful!\n");
/* Restore the NVS memory area */
suspend_nvs_restore();
/* Allow EC transactions to happen. */
ACPI / EC: Add PM operations to improve event handling for resume process This patch makes 2 changes: 1. Restore old behavior Originally, EC driver stops handling both events and transactions in acpi_ec_block_transactions(), and restarts to handle transactions in acpi_ec_unblock_transactions_early(), restarts to handle both events and transactions in acpi_ec_unblock_transactions(). While currently, EC driver still stops handling both events and transactions in acpi_ec_block_transactions(), but restarts to handle both events and transactions in acpi_ec_unblock_transactions_early(). This patch tries to restore the old behavior by dropping __acpi_ec_enable_event() from acpi_unblock_transactions_early(). 2. Improve old behavior However this still cannot fix the real issue as both of the acpi_ec_unblock_xxx() functions are invoked in the noirq stage. Since the EC driver actually doesn't implement the event handling in the polling mode, re-enabling the event handling too early in the noirq stage could result in the problem that if there is no triggering source causing advance_transaction() to be invoked, pending SCI_EVT cannot be detected by the EC driver and _Qxx cannot be triggered. It actually makes sense to restart the event handling in any point during resuming after the noirq stage. Just like the boot stage where the event handling is enabled in .add(), this patch further moves acpi_ec_enable_event() to .resume(). After doing that, the following 2 functions can be combined: acpi_ec_unblock_transactions_early()/acpi_ec_unblock_transactions(). The differences of the event handling availability between the old behavior (this patch isn't applied) and the new behavior (this patch is applied) are as follows: !Applied Applied before suspend Y Y suspend before EC Y Y suspend after EC Y Y suspend_late Y Y suspend_noirq Y (actually N) Y (actually N) resume_noirq Y (actually N) Y (actually N) resume_late Y (actually N) Y (actually N) resume before EC Y (actually N) Y (actually N) resume after EC Y (actually N) Y after resume Y (actually N) Y Where "actually N" means if there is no triggering source, the EC driver is actually not able to notice the pending SCI_EVT occurred in the noirq stage. So we can clearly see that this patch has improved the situation. Signed-off-by: Lv Zheng <lv.zheng@intel.com> Tested-by: Todd E Brandt <todd.e.brandt@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-08-03 11:01:36 +03:00
acpi_ec_unblock_transactions();
}
static void acpi_pm_thaw(void)
{
acpi_ec_unblock_transactions();
acpi_enable_all_runtime_gpes();
}
static const struct platform_hibernation_ops acpi_hibernation_ops = {
.begin = acpi_hibernation_begin,
.end = acpi_pm_end,
.pre_snapshot = acpi_pm_prepare,
.finish = acpi_pm_finish,
.prepare = acpi_pm_prepare,
.enter = acpi_hibernation_enter,
.leave = acpi_hibernation_leave,
.pre_restore = acpi_pm_freeze,
.restore_cleanup = acpi_pm_thaw,
};
/**
* acpi_hibernation_begin_old - Set the target system sleep state to
* ACPI_STATE_S4 and execute the _PTS control method. This
* function is used if the pre-ACPI 2.0 suspend ordering has been
* requested.
*/
static int acpi_hibernation_begin_old(pm_message_t stage)
swsusp: introduce restore platform operations At least on some machines it is necessary to prepare the ACPI firmware for the restoration of the system memory state from the hibernation image if the "platform" mode of hibernation has been used. Namely, in that cases we need to disable the GPEs before replacing the "boot" kernel with the "frozen" kernel (cf. http://bugzilla.kernel.org/show_bug.cgi?id=7887). After the restore they will be re-enabled by hibernation_ops->finish(), but if the restore fails, they have to be re-enabled by the restore code explicitly. For this purpose we can introduce two additional hibernation operations, called pre_restore() and restore_cleanup() and call them from the restore code path. Still, they should be called if the "platform" mode of hibernation has been used, so we need to pass the information about the hibernation mode from the "frozen" kernel to the "boot" kernel in the image header. Apparently, we can't drop the disabling of GPEs before the restore because of Bug #7887 .  We also can't do it unconditionally, because the GPEs wouldn't have been enabled after a successful restore if the suspend had been done in the 'shutdown' or 'reboot' mode. In principle we could (and probably should) unconditionally disable the GPEs before each snapshot creation *and* before the restore, but then we'd have to unconditionally enable them after the snapshot creation as well as after the restore (or restore failure)   Still, for this purpose we'd need to modify acpi_enter_sleep_state_prep() and acpi_leave_sleep_state() and we'd have to introduce some mechanism synchronizing the disablind/enabling of the GPEs with the device drivers' .suspend()/.resume() routines and with disable_/enable_nonboot_cpus().  However, this would have affected the suspend (ie. s2ram) code as well as the hibernation, which I'd like to avoid in this patch series. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Nigel Cunningham <nigel@nigel.suspend2.net> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-19 12:47:30 +04:00
{
int error;
/*
* The _TTS object should always be evaluated before the _PTS object.
* When the old_suspended_ordering is true, the _PTS object is
* evaluated in the acpi_sleep_prepare.
*/
acpi_sleep_tts_switch(ACPI_STATE_S4);
error = acpi_sleep_prepare(ACPI_STATE_S4);
if (error)
return error;
swsusp: introduce restore platform operations At least on some machines it is necessary to prepare the ACPI firmware for the restoration of the system memory state from the hibernation image if the "platform" mode of hibernation has been used. Namely, in that cases we need to disable the GPEs before replacing the "boot" kernel with the "frozen" kernel (cf. http://bugzilla.kernel.org/show_bug.cgi?id=7887). After the restore they will be re-enabled by hibernation_ops->finish(), but if the restore fails, they have to be re-enabled by the restore code explicitly. For this purpose we can introduce two additional hibernation operations, called pre_restore() and restore_cleanup() and call them from the restore code path. Still, they should be called if the "platform" mode of hibernation has been used, so we need to pass the information about the hibernation mode from the "frozen" kernel to the "boot" kernel in the image header. Apparently, we can't drop the disabling of GPEs before the restore because of Bug #7887 .  We also can't do it unconditionally, because the GPEs wouldn't have been enabled after a successful restore if the suspend had been done in the 'shutdown' or 'reboot' mode. In principle we could (and probably should) unconditionally disable the GPEs before each snapshot creation *and* before the restore, but then we'd have to unconditionally enable them after the snapshot creation as well as after the restore (or restore failure)   Still, for this purpose we'd need to modify acpi_enter_sleep_state_prep() and acpi_leave_sleep_state() and we'd have to introduce some mechanism synchronizing the disablind/enabling of the GPEs with the device drivers' .suspend()/.resume() routines and with disable_/enable_nonboot_cpus().  However, this would have affected the suspend (ie. s2ram) code as well as the hibernation, which I'd like to avoid in this patch series. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Nigel Cunningham <nigel@nigel.suspend2.net> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-19 12:47:30 +04:00
if (!nvs_nosave) {
error = suspend_nvs_alloc();
if (error)
return error;
}
if (stage.event == PM_EVENT_HIBERNATE)
pm_set_suspend_via_firmware();
acpi_target_sleep_state = ACPI_STATE_S4;
acpi_scan_lock_acquire();
return 0;
}
/*
* The following callbacks are used if the pre-ACPI 2.0 suspend ordering has
* been requested.
*/
static const struct platform_hibernation_ops acpi_hibernation_ops_old = {
.begin = acpi_hibernation_begin_old,
.end = acpi_pm_end,
.pre_snapshot = acpi_pm_pre_suspend,
.prepare = acpi_pm_freeze,
.finish = acpi_pm_finish,
.enter = acpi_hibernation_enter,
.leave = acpi_hibernation_leave,
.pre_restore = acpi_pm_freeze,
.restore_cleanup = acpi_pm_thaw,
.recover = acpi_pm_finish,
};
static void acpi_sleep_hibernate_setup(void)
{
if (!acpi_sleep_state_supported(ACPI_STATE_S4))
return;
hibernation_set_ops(old_suspend_ordering ?
&acpi_hibernation_ops_old : &acpi_hibernation_ops);
sleep_states[ACPI_STATE_S4] = 1;
if (nosigcheck)
return;
acpi_get_table(ACPI_SIG_FACS, 1, (struct acpi_table_header **)&facs);
if (facs)
s4_hardware_signature = facs->hardware_signature;
}
#else /* !CONFIG_HIBERNATION */
static inline void acpi_sleep_hibernate_setup(void) {}
#endif /* !CONFIG_HIBERNATION */
static void acpi_power_off_prepare(void)
{
/* Prepare to power off the system */
acpi_sleep_prepare(ACPI_STATE_S5);
acpi_disable_all_gpes();
acpi_os_wait_events_complete();
}
static void acpi_power_off(void)
{
/* acpi_sleep_prepare(ACPI_STATE_S5) should have already been called */
pr_debug("%s called\n", __func__);
local_irq_disable();
acpi_enter_sleep_state(ACPI_STATE_S5);
}
int __init acpi_sleep_init(void)
{
char supported[ACPI_S_STATE_COUNT * 3 + 1];
char *pos = supported;
int i;
acpi_sleep_dmi_check();
sleep_states[ACPI_STATE_S0] = 1;
acpi_sleep_syscore_init();
acpi_sleep_suspend_setup();
acpi_sleep_hibernate_setup();
if (acpi_sleep_state_supported(ACPI_STATE_S5)) {
sleep_states[ACPI_STATE_S5] = 1;
pm_power_off_prepare = acpi_power_off_prepare;
pm_power_off = acpi_power_off;
} else {
acpi_no_s5 = true;
}
supported[0] = 0;
for (i = 0; i < ACPI_S_STATE_COUNT; i++) {
if (sleep_states[i])
pos += sprintf(pos, " S%d", i);
}
pr_info("(supports%s)\n", supported);
/*
* Register the tts_notifier to reboot notifier list so that the _TTS
* object can also be evaluated when the system enters S5.
*/
register_reboot_notifier(&tts_notifier);
return 0;
}