linux/arch/arm/mach-omap2/omap_phy_internal.c

// SPDX-License-Identifier: GPL-2.0-or-later
/*
  * This file configures the internal USB PHY in OMAP4430. Used
  * with TWL6030 transceiver and MUSB on OMAP4430.
  *
  * Copyright (C) 2010 Texas Instruments Incorporated - https://www.ti.com
  * Author: Hema HK <hemahk@ti.com>
  */

#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt

#include <linux/types.h>
#include <linux/delay.h>
#include <linux/clk.h>
#include <linux/io.h>
#include <linux/err.h>
#include <linux/usb.h>
#include <linux/usb/musb.h>

#include "soc.h"
#include "control.h"
#include "usb.h"

#define CONTROL_DEV_CONF		0x300
#define PHY_PD				0x1

/**
 * omap4430_phy_power_down: disable MUSB PHY during early init
 *
 * OMAP4 MUSB PHY module is enabled by default on reset, but this will
 * prevent core retention if not disabled by SW. USB driver will
 * later on enable this, once and if the driver needs it.
 */
static int __init omap4430_phy_power_down(void)
{
	void __iomem *ctrl_base;

	if (!cpu_is_omap44xx())
		return 0;

	ctrl_base = ioremap(OMAP443X_SCM_BASE, SZ_1K);
	if (!ctrl_base) {
		pr_err("control module ioremap failed\n");
		return -ENOMEM;
	}

	/* Power down the phy */
	writel_relaxed(PHY_PD, ctrl_base + CONTROL_DEV_CONF);

	iounmap(ctrl_base);

	return 0;
}
omap_early_initcall(omap4430_phy_power_down);

void am35x_musb_reset(void)
{
	u32	regval;

	/* Reset the musb interface */
	regval = omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET);

	regval |= AM35XX_USBOTGSS_SW_RST;
	omap_ctrl_writel(regval, AM35XX_CONTROL_IP_SW_RESET);

	regval &= ~AM35XX_USBOTGSS_SW_RST;
	omap_ctrl_writel(regval, AM35XX_CONTROL_IP_SW_RESET);

	regval = omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET);
}

void am35x_musb_phy_power(u8 on)
{
	unsigned long timeout = jiffies + msecs_to_jiffies(100);
	u32 devconf2;

	if (on) {
		/*
		 * Start the on-chip PHY and its PLL.
		 */
		devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);

		devconf2 &= ~(CONF2_RESET | CONF2_PHYPWRDN | CONF2_OTGPWRDN);
		devconf2 |= CONF2_PHY_PLLON;

		omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);

		pr_info("Waiting for PHY clock good...\n");
		while (!(omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2)
				& CONF2_PHYCLKGD)) {
			cpu_relax();

			if (time_after(jiffies, timeout)) {
				pr_err("musb PHY clock good timed out\n");
				break;
			}
		}
	} else {
		/*
		 * Power down the on-chip PHY.
		 */
		devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);

		devconf2 &= ~CONF2_PHY_PLLON;
		devconf2 |=  CONF2_PHYPWRDN | CONF2_OTGPWRDN;
		omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
	}
}

void am35x_musb_clear_irq(void)
{
	u32 regval;

	regval = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR);
	regval |= AM35XX_USBOTGSS_INT_CLR;
	omap_ctrl_writel(regval, AM35XX_CONTROL_LVL_INTR_CLEAR);
	regval = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR);
}

void am35x_set_mode(u8 musb_mode)
{
	u32 devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);

	devconf2 &= ~CONF2_OTGMODE;
	switch (musb_mode) {
	case MUSB_HOST:		/* Force VBUS valid, ID = 0 */
		devconf2 |= CONF2_FORCE_HOST;
		break;
	case MUSB_PERIPHERAL:	/* Force VBUS valid, ID = 1 */
		devconf2 |= CONF2_FORCE_DEVICE;
		break;
	case MUSB_OTG:		/* Don't override the VBUS/ID comparators */
		devconf2 |= CONF2_NO_OVERRIDE;
		break;
	default:
		pr_info("Unsupported mode %u\n", musb_mode);
	}

	omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
}