iv/linux
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
linux/drivers/usb/gadget/net2280.h

731 lines
31 KiB
C
Raw Normal View History

Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 15:20:36 -07:00
/*
* NetChip 2280 high/full speed USB device controller.
* Unlike many such controllers, this one talks PCI.
*/
/*
* Copyright (C) 2002 NetChip Technology, Inc. (http://www.netchip.com)
* Copyright (C) 2003 David Brownell
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
/*-------------------------------------------------------------------------*/
/* NET2280 MEMORY MAPPED REGISTERS
*
* The register layout came from the chip documentation, and the bit
* number definitions were extracted from chip specification.
*
* Use the shift operator ('<<') to build bit masks, with readl/writel
* to access the registers through PCI.
*/
/* main registers, BAR0 + 0x0000 */
struct net2280_regs {
// offset 0x0000
u32 devinit;
#define LOCAL_CLOCK_FREQUENCY 8
#define FORCE_PCI_RESET 7
#define PCI_ID 6
#define PCI_ENABLE 5
#define FIFO_SOFT_RESET 4
#define CFG_SOFT_RESET 3
#define PCI_SOFT_RESET 2
#define USB_SOFT_RESET 1
#define M8051_RESET 0
u32 eectl;
#define EEPROM_ADDRESS_WIDTH 23
#define EEPROM_CHIP_SELECT_ACTIVE 22
#define EEPROM_PRESENT 21
#define EEPROM_VALID 20
#define EEPROM_BUSY 19
#define EEPROM_CHIP_SELECT_ENABLE 18
#define EEPROM_BYTE_READ_START 17
#define EEPROM_BYTE_WRITE_START 16
#define EEPROM_READ_DATA 8
#define EEPROM_WRITE_DATA 0
u32 eeclkfreq;
u32 _unused0;
// offset 0x0010
u32 pciirqenb0; /* interrupt PCI master ... */
#define SETUP_PACKET_INTERRUPT_ENABLE 7
#define ENDPOINT_F_INTERRUPT_ENABLE 6
#define ENDPOINT_E_INTERRUPT_ENABLE 5
#define ENDPOINT_D_INTERRUPT_ENABLE 4
#define ENDPOINT_C_INTERRUPT_ENABLE 3
#define ENDPOINT_B_INTERRUPT_ENABLE 2
#define ENDPOINT_A_INTERRUPT_ENABLE 1
#define ENDPOINT_0_INTERRUPT_ENABLE 0
u32 pciirqenb1;
#define PCI_INTERRUPT_ENABLE 31
#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
#define PCI_TARGET_ABORT_ASSERTED_INTERRUPT_ENABLE 18
#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
#define GPIO_INTERRUPT_ENABLE 13
#define DMA_D_INTERRUPT_ENABLE 12
#define DMA_C_INTERRUPT_ENABLE 11
#define DMA_B_INTERRUPT_ENABLE 10
#define DMA_A_INTERRUPT_ENABLE 9
#define EEPROM_DONE_INTERRUPT_ENABLE 8
#define VBUS_INTERRUPT_ENABLE 7
#define CONTROL_STATUS_INTERRUPT_ENABLE 6
#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
#define RESUME_INTERRUPT_ENABLE 1
#define SOF_INTERRUPT_ENABLE 0
u32 cpu_irqenb0; /* ... or onboard 8051 */
#define SETUP_PACKET_INTERRUPT_ENABLE 7
#define ENDPOINT_F_INTERRUPT_ENABLE 6
#define ENDPOINT_E_INTERRUPT_ENABLE 5
#define ENDPOINT_D_INTERRUPT_ENABLE 4
#define ENDPOINT_C_INTERRUPT_ENABLE 3
#define ENDPOINT_B_INTERRUPT_ENABLE 2
#define ENDPOINT_A_INTERRUPT_ENABLE 1
#define ENDPOINT_0_INTERRUPT_ENABLE 0
u32 cpu_irqenb1;
#define CPU_INTERRUPT_ENABLE 31
#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
#define PCI_INTA_INTERRUPT_ENABLE 24
#define PCI_PME_INTERRUPT_ENABLE 23
#define PCI_SERR_INTERRUPT_ENABLE 22
#define PCI_PERR_INTERRUPT_ENABLE 21
#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
#define GPIO_INTERRUPT_ENABLE 13
#define DMA_D_INTERRUPT_ENABLE 12
#define DMA_C_INTERRUPT_ENABLE 11
#define DMA_B_INTERRUPT_ENABLE 10
#define DMA_A_INTERRUPT_ENABLE 9
#define EEPROM_DONE_INTERRUPT_ENABLE 8
#define VBUS_INTERRUPT_ENABLE 7
#define CONTROL_STATUS_INTERRUPT_ENABLE 6
#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
#define RESUME_INTERRUPT_ENABLE 1
#define SOF_INTERRUPT_ENABLE 0
// offset 0x0020
u32 _unused1;
u32 usbirqenb1;
#define USB_INTERRUPT_ENABLE 31
#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27
#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26
#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25
#define PCI_INTA_INTERRUPT_ENABLE 24
#define PCI_PME_INTERRUPT_ENABLE 23
#define PCI_SERR_INTERRUPT_ENABLE 22
#define PCI_PERR_INTERRUPT_ENABLE 21
#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20
#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19
#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17
#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16
#define GPIO_INTERRUPT_ENABLE 13
#define DMA_D_INTERRUPT_ENABLE 12
#define DMA_C_INTERRUPT_ENABLE 11
#define DMA_B_INTERRUPT_ENABLE 10
#define DMA_A_INTERRUPT_ENABLE 9
#define EEPROM_DONE_INTERRUPT_ENABLE 8
#define VBUS_INTERRUPT_ENABLE 7
#define CONTROL_STATUS_INTERRUPT_ENABLE 6
#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4
#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3
#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2
#define RESUME_INTERRUPT_ENABLE 1
#define SOF_INTERRUPT_ENABLE 0
u32 irqstat0;
#define INTA_ASSERTED 12
#define SETUP_PACKET_INTERRUPT 7
#define ENDPOINT_F_INTERRUPT 6
#define ENDPOINT_E_INTERRUPT 5
#define ENDPOINT_D_INTERRUPT 4
#define ENDPOINT_C_INTERRUPT 3
#define ENDPOINT_B_INTERRUPT 2
#define ENDPOINT_A_INTERRUPT 1
#define ENDPOINT_0_INTERRUPT 0
u32 irqstat1;
#define POWER_STATE_CHANGE_INTERRUPT 27
#define PCI_ARBITER_TIMEOUT_INTERRUPT 26
#define PCI_PARITY_ERROR_INTERRUPT 25
#define PCI_INTA_INTERRUPT 24
#define PCI_PME_INTERRUPT 23
#define PCI_SERR_INTERRUPT 22
#define PCI_PERR_INTERRUPT 21
#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT 20
#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT 19
#define PCI_RETRY_ABORT_INTERRUPT 17
#define PCI_MASTER_CYCLE_DONE_INTERRUPT 16
[PATCH] USB: net2282 and net2280 software compatibility Below is a patch to gadgets/net2280.[ch] which adds support for the net2282 controller. The original code was kindly provided by PLX Technology, I just merged it with the current net2280 driver in the kernel. Tested on 2.6.15.6, but only with 2282. I did the merge, so that the behaviour for the 2280 is unaffected (except for short delays for extra checks). Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Support for net2282 in net2280 driver.
2006-03-19 20:49:14 +01:00
#define SOF_DOWN_INTERRUPT 14
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 15:20:36 -07:00
#define GPIO_INTERRUPT 13
#define DMA_D_INTERRUPT 12
#define DMA_C_INTERRUPT 11
#define DMA_B_INTERRUPT 10
#define DMA_A_INTERRUPT 9
#define EEPROM_DONE_INTERRUPT 8
#define VBUS_INTERRUPT 7
#define CONTROL_STATUS_INTERRUPT 6
#define ROOT_PORT_RESET_INTERRUPT 4
#define SUSPEND_REQUEST_INTERRUPT 3
#define SUSPEND_REQUEST_CHANGE_INTERRUPT 2
#define RESUME_INTERRUPT 1
#define SOF_INTERRUPT 0
// offset 0x0030
u32 idxaddr;
u32 idxdata;
u32 fifoctl;
#define PCI_BASE2_RANGE 16
#define IGNORE_FIFO_AVAILABILITY 3
#define PCI_BASE2_SELECT 2
#define FIFO_CONFIGURATION_SELECT 0
u32 _unused2;
// offset 0x0040
u32 memaddr;
#define START 28
#define DIRECTION 27
#define FIFO_DIAGNOSTIC_SELECT 24
#define MEMORY_ADDRESS 0
u32 memdata0;
u32 memdata1;
u32 _unused3;
// offset 0x0050
u32 gpioctl;
#define GPIO3_LED_SELECT 12
#define GPIO3_INTERRUPT_ENABLE 11
#define GPIO2_INTERRUPT_ENABLE 10
#define GPIO1_INTERRUPT_ENABLE 9
#define GPIO0_INTERRUPT_ENABLE 8
#define GPIO3_OUTPUT_ENABLE 7
#define GPIO2_OUTPUT_ENABLE 6
#define GPIO1_OUTPUT_ENABLE 5
#define GPIO0_OUTPUT_ENABLE 4
#define GPIO3_DATA 3
#define GPIO2_DATA 2
#define GPIO1_DATA 1
#define GPIO0_DATA 0
u32 gpiostat;
#define GPIO3_INTERRUPT 3
#define GPIO2_INTERRUPT 2
#define GPIO1_INTERRUPT 1
#define GPIO0_INTERRUPT 0
} __attribute__ ((packed));
/* usb control, BAR0 + 0x0080 */
struct net2280_usb_regs {
// offset 0x0080
u32 stdrsp;
#define STALL_UNSUPPORTED_REQUESTS 31
#define SET_TEST_MODE 16
#define GET_OTHER_SPEED_CONFIGURATION 15
#define GET_DEVICE_QUALIFIER 14
#define SET_ADDRESS 13
#define ENDPOINT_SET_CLEAR_HALT 12
#define DEVICE_SET_CLEAR_DEVICE_REMOTE_WAKEUP 11
#define GET_STRING_DESCRIPTOR_2 10
#define GET_STRING_DESCRIPTOR_1 9
#define GET_STRING_DESCRIPTOR_0 8
#define GET_SET_INTERFACE 6
#define GET_SET_CONFIGURATION 5
#define GET_CONFIGURATION_DESCRIPTOR 4
#define GET_DEVICE_DESCRIPTOR 3
#define GET_ENDPOINT_STATUS 2
#define GET_INTERFACE_STATUS 1
#define GET_DEVICE_STATUS 0
u32 prodvendid;
#define PRODUCT_ID 16
#define VENDOR_ID 0
u32 relnum;
u32 usbctl;
#define SERIAL_NUMBER_INDEX 16
#define PRODUCT_ID_STRING_ENABLE 13
#define VENDOR_ID_STRING_ENABLE 12
#define USB_ROOT_PORT_WAKEUP_ENABLE 11
#define VBUS_PIN 10
#define TIMED_DISCONNECT 9
#define SUSPEND_IMMEDIATELY 7
#define SELF_POWERED_USB_DEVICE 6
#define REMOTE_WAKEUP_SUPPORT 5
#define PME_POLARITY 4
#define USB_DETECT_ENABLE 3
#define PME_WAKEUP_ENABLE 2
#define DEVICE_REMOTE_WAKEUP_ENABLE 1
#define SELF_POWERED_STATUS 0
// offset 0x0090
u32 usbstat;
#define HIGH_SPEED 7
#define FULL_SPEED 6
#define GENERATE_RESUME 5
#define GENERATE_DEVICE_REMOTE_WAKEUP 4
u32 xcvrdiag;
#define FORCE_HIGH_SPEED_MODE 31
#define FORCE_FULL_SPEED_MODE 30
#define USB_TEST_MODE 24
#define LINE_STATE 16
#define TRANSCEIVER_OPERATION_MODE 2
#define TRANSCEIVER_SELECT 1
#define TERMINATION_SELECT 0
u32 setup0123;
u32 setup4567;
// offset 0x0090
u32 _unused0;
u32 ouraddr;
#define FORCE_IMMEDIATE 7
#define OUR_USB_ADDRESS 0
u32 ourconfig;
} __attribute__ ((packed));
/* pci control, BAR0 + 0x0100 */
struct net2280_pci_regs {
// offset 0x0100
u32 pcimstctl;
#define PCI_ARBITER_PARK_SELECT 13
#define PCI_MULTI LEVEL_ARBITER 12
#define PCI_RETRY_ABORT_ENABLE 11
#define DMA_MEMORY_WRITE_AND_INVALIDATE_ENABLE 10
#define DMA_READ_MULTIPLE_ENABLE 9
#define DMA_READ_LINE_ENABLE 8
#define PCI_MASTER_COMMAND_SELECT 6
#define MEM_READ_OR_WRITE 0
#define IO_READ_OR_WRITE 1
#define CFG_READ_OR_WRITE 2
#define PCI_MASTER_START 5
#define PCI_MASTER_READ_WRITE 4
#define PCI_MASTER_WRITE 0
#define PCI_MASTER_READ 1
#define PCI_MASTER_BYTE_WRITE_ENABLES 0
u32 pcimstaddr;
u32 pcimstdata;
u32 pcimststat;
#define PCI_ARBITER_CLEAR 2
#define PCI_EXTERNAL_ARBITER 1
#define PCI_HOST_MODE 0
} __attribute__ ((packed));
/* dma control, BAR0 + 0x0180 ... array of four structs like this,
* for channels 0..3. see also struct net2280_dma: descriptor
* that can be loaded into some of these registers.
*/
struct net2280_dma_regs { /* [11.7] */
// offset 0x0180, 0x01a0, 0x01c0, 0x01e0,
u32 dmactl;
#define DMA_SCATTER_GATHER_DONE_INTERRUPT_ENABLE 25
#define DMA_CLEAR_COUNT_ENABLE 21
#define DESCRIPTOR_POLLING_RATE 19
#define POLL_CONTINUOUS 0
#define POLL_1_USEC 1
#define POLL_100_USEC 2
#define POLL_1_MSEC 3
#define DMA_VALID_BIT_POLLING_ENABLE 18
#define DMA_VALID_BIT_ENABLE 17
#define DMA_SCATTER_GATHER_ENABLE 16
#define DMA_OUT_AUTO_START_ENABLE 4
#define DMA_PREEMPT_ENABLE 3
#define DMA_FIFO_VALIDATE 2
#define DMA_ENABLE 1
#define DMA_ADDRESS_HOLD 0
u32 dmastat;
[PATCH] USB: net2282 and net2280 software compatibility Below is a patch to gadgets/net2280.[ch] which adds support for the net2282 controller. The original code was kindly provided by PLX Technology, I just merged it with the current net2280 driver in the kernel. Tested on 2.6.15.6, but only with 2282. I did the merge, so that the behaviour for the 2280 is unaffected (except for short delays for extra checks). Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Support for net2282 in net2280 driver.
2006-03-19 20:49:14 +01:00
#define DMA_ABORT_DONE_INTERRUPT 27
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-16 15:20:36 -07:00
#define DMA_SCATTER_GATHER_DONE_INTERRUPT 25
#define DMA_TRANSACTION_DONE_INTERRUPT 24
#define DMA_ABORT 1
#define DMA_START 0
u32 _unused0 [2];
// offset 0x0190, 0x01b0, 0x01d0, 0x01f0,
u32 dmacount;
#define VALID_BIT 31
#define DMA_DIRECTION 30
#define DMA_DONE_INTERRUPT_ENABLE 29
#define END_OF_CHAIN 28
#define DMA_BYTE_COUNT_MASK ((1<<24)-1)
#define DMA_BYTE_COUNT 0
u32 dmaaddr;
u32 dmadesc;
u32 _unused1;
} __attribute__ ((packed));
/* dedicated endpoint registers, BAR0 + 0x0200 */
struct net2280_dep_regs { /* [11.8] */
// offset 0x0200, 0x0210, 0x220, 0x230, 0x240
u32 dep_cfg;
// offset 0x0204, 0x0214, 0x224, 0x234, 0x244
u32 dep_rsp;
u32 _unused [2];
} __attribute__ ((packed));
/* configurable endpoint registers, BAR0 + 0x0300 ... array of seven structs
* like this, for ep0 then the configurable endpoints A..F
* ep0 reserved for control; E and F have only 64 bytes of fifo
*/
struct net2280_ep_regs { /* [11.9] */
// offset 0x0300, 0x0320, 0x0340, 0x0360, 0x0380, 0x03a0, 0x03c0
u32 ep_cfg;
#define ENDPOINT_BYTE_COUNT 16
#define ENDPOINT_ENABLE 10
#define ENDPOINT_TYPE 8
#define ENDPOINT_DIRECTION 7
#define ENDPOINT_NUMBER 0
u32 ep_rsp;
#define SET_NAK_OUT_PACKETS 15
#define SET_EP_HIDE_STATUS_PHASE 14
#define SET_EP_FORCE_CRC_ERROR 13
#define SET_INTERRUPT_MODE 12
#define SET_CONTROL_STATUS_PHASE_HANDSHAKE 11
#define SET_NAK_OUT_PACKETS_MODE 10
#define SET_ENDPOINT_TOGGLE 9
#define SET_ENDPOINT_HALT 8
#define CLEAR_NAK_OUT_PACKETS 7
#define CLEAR_EP_HIDE_STATUS_PHASE 6
#define CLEAR_EP_FORCE_CRC_ERROR 5
#define CLEAR_INTERRUPT_MODE 4
#define CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE 3
#define CLEAR_NAK_OUT_PACKETS_MODE 2
#define CLEAR_ENDPOINT_TOGGLE 1
#define CLEAR_ENDPOINT_HALT 0
u32 ep_irqenb;
#define SHORT_PACKET_OUT_DONE_INTERRUPT_ENABLE 6
#define SHORT_PACKET_TRANSFERRED_INTERRUPT_ENABLE 5
#define DATA_PACKET_RECEIVED_INTERRUPT_ENABLE 3
#define DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE 2
#define DATA_OUT_PING_TOKEN_INTERRUPT_ENABLE 1
#define DATA_IN_TOKEN_INTERRUPT_ENABLE 0
u32 ep_stat;
#define FIFO_VALID_COUNT 24
#define HIGH_BANDWIDTH_OUT_TRANSACTION_PID 22
#define TIMEOUT 21
#define USB_STALL_SENT 20
#define USB_IN_NAK_SENT 19
#define USB_IN_ACK_RCVD 18
#define USB_OUT_PING_NAK_SENT 17
#define USB_OUT_ACK_SENT 16
#define FIFO_OVERFLOW 13
#define FIFO_UNDERFLOW 12
#define FIFO_FULL 11
#define FIFO_EMPTY 10
#define FIFO_FLUSH 9
#define SHORT_PACKET_OUT_DONE_INTERRUPT 6
#define SHORT_PACKET_TRANSFERRED_INTERRUPT 5
#define NAK_OUT_PACKETS 4
#define DATA_PACKET_RECEIVED_INTERRUPT 3
#define DATA_PACKET_TRANSMITTED_INTERRUPT 2
#define DATA_OUT_PING_TOKEN_INTERRUPT 1
#define DATA_IN_TOKEN_INTERRUPT 0
// offset 0x0310, 0x0330, 0x0350, 0x0370, 0x0390, 0x03b0, 0x03d0
u32 ep_avail;
u32 ep_data;
u32 _unused0 [2];
} __attribute__ ((packed));
/*-------------------------------------------------------------------------*/
#ifdef __KERNEL__
/* indexed registers [11.10] are accessed indirectly
* caller must own the device lock.
*/
static inline u32
get_idx_reg (struct net2280_regs __iomem *regs, u32 index)
{
writel (index, &regs->idxaddr);
/* NOTE: synchs device/cpu memory views */
return readl (&regs->idxdata);
}
static inline void
set_idx_reg (struct net2280_regs __iomem *regs, u32 index, u32 value)
{
writel (index, &regs->idxaddr);
writel (value, &regs->idxdata);
/* posted, may not be visible yet */
}
#endif /* __KERNEL__ */
#define REG_DIAG 0x0
#define RETRY_COUNTER 16
#define FORCE_PCI_SERR 11
#define FORCE_PCI_INTERRUPT 10
#define FORCE_USB_INTERRUPT 9
#define FORCE_CPU_INTERRUPT 8
#define ILLEGAL_BYTE_ENABLES 5
#define FAST_TIMES 4
#define FORCE_RECEIVE_ERROR 2
#define FORCE_TRANSMIT_CRC_ERROR 0
#define REG_FRAME 0x02 /* from last sof */
#define REG_CHIPREV 0x03 /* in bcd */
#define REG_HS_NAK_RATE 0x0a /* NAK per N uframes */
#define CHIPREV_1 0x0100
#define CHIPREV_1A 0x0110
#ifdef __KERNEL__
/* ep a-f highspeed and fullspeed maxpacket, addresses
* computed from ep->num
*/
#define REG_EP_MAXPKT(dev,num) (((num) + 1) * 0x10 + \
(((dev)->gadget.speed == USB_SPEED_HIGH) ? 0 : 1))
/*-------------------------------------------------------------------------*/
/* [8.3] for scatter/gather i/o
* use struct net2280_dma_regs bitfields
*/
struct net2280_dma {
__le32 dmacount;
__le32 dmaaddr; /* the buffer */
__le32 dmadesc; /* next dma descriptor */
__le32 _reserved;
} __attribute__ ((aligned (16)));
/*-------------------------------------------------------------------------*/
/* DRIVER DATA STRUCTURES and UTILITIES */
struct net2280_ep {
struct usb_ep ep;
struct net2280_ep_regs __iomem *regs;
struct net2280_dma_regs __iomem *dma;
struct net2280_dma *dummy;
dma_addr_t td_dma; /* of dummy */
struct net2280 *dev;
unsigned long irqs;
/* analogous to a host-side qh */
struct list_head queue;
const struct usb_endpoint_descriptor *desc;
unsigned num : 8,
fifo_size : 12,
in_fifo_validate : 1,
out_overflow : 1,
stopped : 1,
is_in : 1,
is_iso : 1;
};
static inline void allow_status (struct net2280_ep *ep)
{
/* ep0 only */
writel ( (1 << CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE)
| (1 << CLEAR_NAK_OUT_PACKETS)
| (1 << CLEAR_NAK_OUT_PACKETS_MODE)
, &ep->regs->ep_rsp);
ep->stopped = 1;
}
/* count (<= 4) bytes in the next fifo write will be valid */
static inline void set_fifo_bytecount (struct net2280_ep *ep, unsigned count)
{
writeb (count, 2 + (u8 __iomem *) &ep->regs->ep_cfg);
}
struct net2280_request {
struct usb_request req;
struct net2280_dma *td;
dma_addr_t td_dma;
struct list_head queue;
unsigned mapped : 1,
valid : 1;
};
struct net2280 {
/* each pci device provides one gadget, several endpoints */
struct usb_gadget gadget;
spinlock_t lock;
struct net2280_ep ep [7];
struct usb_gadget_driver *driver;
unsigned enabled : 1,
protocol_stall : 1,
softconnect : 1,
got_irq : 1,
region : 1;
u16 chiprev;
/* pci state used to access those endpoints */
struct pci_dev *pdev;
struct net2280_regs __iomem *regs;
struct net2280_usb_regs __iomem *usb;
struct net2280_pci_regs __iomem *pci;
struct net2280_dma_regs __iomem *dma;
struct net2280_dep_regs __iomem *dep;
struct net2280_ep_regs __iomem *epregs;
struct pci_pool *requests;
// statistics...
};
static inline void set_halt (struct net2280_ep *ep)
{
/* ep0 and bulk/intr endpoints */
writel ( (1 << CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE)
/* set NAK_OUT for erratum 0114 */
| ((ep->dev->chiprev == CHIPREV_1) << SET_NAK_OUT_PACKETS)
| (1 << SET_ENDPOINT_HALT)
, &ep->regs->ep_rsp);
}
static inline void clear_halt (struct net2280_ep *ep)
{
/* ep0 and bulk/intr endpoints */
writel ( (1 << CLEAR_ENDPOINT_HALT)
| (1 << CLEAR_ENDPOINT_TOGGLE)
/* unless the gadget driver left a short packet in the
* fifo, this reverses the erratum 0114 workaround.
*/
| ((ep->dev->chiprev == CHIPREV_1) << CLEAR_NAK_OUT_PACKETS)
, &ep->regs->ep_rsp);
}
#ifdef USE_RDK_LEDS
static inline void net2280_led_init (struct net2280 *dev)
{
/* LED3 (green) is on during USB activity. note erratum 0113. */
writel ((1 << GPIO3_LED_SELECT)
| (1 << GPIO3_OUTPUT_ENABLE)
| (1 << GPIO2_OUTPUT_ENABLE)
| (1 << GPIO1_OUTPUT_ENABLE)
| (1 << GPIO0_OUTPUT_ENABLE)
, &dev->regs->gpioctl);
}
/* indicate speed with bi-color LED 0/1 */
static inline
void net2280_led_speed (struct net2280 *dev, enum usb_device_speed speed)
{
u32 val = readl (&dev->regs->gpioctl);
switch (speed) {
case USB_SPEED_HIGH: /* green */
val &= ~(1 << GPIO0_DATA);
val |= (1 << GPIO1_DATA);
break;
case USB_SPEED_FULL: /* red */
val &= ~(1 << GPIO1_DATA);
val |= (1 << GPIO0_DATA);
break;
default: /* (off/black) */
val &= ~((1 << GPIO1_DATA) | (1 << GPIO0_DATA));
break;
}
writel (val, &dev->regs->gpioctl);
}
/* indicate power with LED 2 */
static inline void net2280_led_active (struct net2280 *dev, int is_active)
{
u32 val = readl (&dev->regs->gpioctl);
// FIXME this LED never seems to turn on.
if (is_active)
val |= GPIO2_DATA;
else
val &= ~GPIO2_DATA;
writel (val, &dev->regs->gpioctl);
}
static inline void net2280_led_shutdown (struct net2280 *dev)
{
/* turn off all four GPIO*_DATA bits */
writel (readl (&dev->regs->gpioctl) & ~0x0f,
&dev->regs->gpioctl);
}
#else
#define net2280_led_init(dev) do { } while (0)
#define net2280_led_speed(dev, speed) do { } while (0)
#define net2280_led_shutdown(dev) do { } while (0)
#endif
/*-------------------------------------------------------------------------*/
#define xprintk(dev,level,fmt,args...) \
printk(level "%s %s: " fmt , driver_name , \
pci_name(dev->pdev) , ## args)
#ifdef DEBUG
#undef DEBUG
#define DEBUG(dev,fmt,args...) \
xprintk(dev , KERN_DEBUG , fmt , ## args)
#else
#define DEBUG(dev,fmt,args...) \
do { } while (0)
#endif /* DEBUG */
#ifdef VERBOSE
#define VDEBUG DEBUG
#else
#define VDEBUG(dev,fmt,args...) \
do { } while (0)
#endif /* VERBOSE */
#define ERROR(dev,fmt,args...) \
xprintk(dev , KERN_ERR , fmt , ## args)
#define WARN(dev,fmt,args...) \
xprintk(dev , KERN_WARNING , fmt , ## args)
#define INFO(dev,fmt,args...) \
xprintk(dev , KERN_INFO , fmt , ## args)
/*-------------------------------------------------------------------------*/
static inline void start_out_naking (struct net2280_ep *ep)
{
/* NOTE: hardware races lurk here, and PING protocol issues */
writel ((1 << SET_NAK_OUT_PACKETS), &ep->regs->ep_rsp);
/* synch with device */
readl (&ep->regs->ep_rsp);
}
#ifdef DEBUG
static inline void assert_out_naking (struct net2280_ep *ep, const char *where)
{
u32 tmp = readl (&ep->regs->ep_stat);
if ((tmp & (1 << NAK_OUT_PACKETS)) == 0) {
DEBUG (ep->dev, "%s %s %08x !NAK\n",
ep->ep.name, where, tmp);
writel ((1 << SET_NAK_OUT_PACKETS),
&ep->regs->ep_rsp);
}
}
#define ASSERT_OUT_NAKING(ep) assert_out_naking(ep,__FUNCTION__)
#else
#define ASSERT_OUT_NAKING(ep) do {} while (0)
#endif
static inline void stop_out_naking (struct net2280_ep *ep)
{
u32 tmp;
tmp = readl (&ep->regs->ep_stat);
if ((tmp & (1 << NAK_OUT_PACKETS)) != 0)
writel ((1 << CLEAR_NAK_OUT_PACKETS), &ep->regs->ep_rsp);
}
#endif /* __KERNEL__ */
Reference in New Issue Copy Permalink