power: supply: twl4030-charger: don't check if battery is present
We can't assume that the battery is or stays present after probing on devices with replaceable battery. On some devices (e.g. GTA04 or OpenPanodra) it can be removed and even be hot swapped by the user while device continues to operate through external AC or USB power (as long as system power consumption remains below ca. 500mA as provided by USB). Under certain conditions it is possible to boot without battery. So it makes no sense to check for this situation during probe and make the charger driver (and its status reports) completely non-operational if the battery can be inserted later. Tested on: GTA04 and OpenPandora. Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This commit is contained in:
parent
3fb319c2cd
commit
19a2ee69c2
@ -205,35 +205,6 @@ static int twl4030bci_read_adc_val(u8 reg)
|
||||
return temp | val;
|
||||
}
|
||||
|
||||
/*
|
||||
* Check if Battery Pack was present
|
||||
*/
|
||||
static int twl4030_is_battery_present(struct twl4030_bci *bci)
|
||||
{
|
||||
int ret;
|
||||
u8 val = 0;
|
||||
|
||||
/* Battery presence in Main charge? */
|
||||
ret = twl_i2c_read_u8(TWL_MODULE_MAIN_CHARGE, &val, TWL4030_BCIMFSTS3);
|
||||
if (ret)
|
||||
return ret;
|
||||
if (val & TWL4030_BATSTSMCHG)
|
||||
return 0;
|
||||
|
||||
/*
|
||||
* OK, It could be that bootloader did not enable main charger,
|
||||
* pre-charge is h/w auto. So, Battery presence in Pre-charge?
|
||||
*/
|
||||
ret = twl_i2c_read_u8(TWL4030_MODULE_PRECHARGE, &val,
|
||||
TWL4030_BCIMFSTS1);
|
||||
if (ret)
|
||||
return ret;
|
||||
if (val & TWL4030_BATSTSPCHG)
|
||||
return 0;
|
||||
|
||||
return -ENODEV;
|
||||
}
|
||||
|
||||
/*
|
||||
* TI provided formulas:
|
||||
* CGAIN == 0: ICHG = (BCIICHG * 1.7) / (2^10 - 1) - 0.85
|
||||
@ -1068,13 +1039,6 @@ static int twl4030_bci_probe(struct platform_device *pdev)
|
||||
bci->irq_chg = platform_get_irq(pdev, 0);
|
||||
bci->irq_bci = platform_get_irq(pdev, 1);
|
||||
|
||||
/* Only proceed further *IF* battery is physically present */
|
||||
ret = twl4030_is_battery_present(bci);
|
||||
if (ret) {
|
||||
dev_crit(&pdev->dev, "Battery was not detected:%d\n", ret);
|
||||
return ret;
|
||||
}
|
||||
|
||||
platform_set_drvdata(pdev, bci);
|
||||
|
||||
bci->ac = devm_power_supply_register(&pdev->dev, &twl4030_bci_ac_desc,
|
||||
|
Loading…
Reference in New Issue
Block a user