Several fixes for the AVR32 PATA driver

Several fixes for the AVR32 PATA driver:

* Updated to use new AVR32 SMC timing API. This removes the need for "magic"
constants in signal timing.

* Removed the ATA_FLAG_PIO_POLLING, the driver should use interrupts.

* Removed .port_disable and .irq_ack as these are no longer needed.

* Improved some comments.

Signed-off-by: Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This commit is contained in:
Kristoffer Nyborg Gregertsen 2007-11-29 12:01:51 +01:00 committed by Jeff Garzik
parent 2d79ab8fd7
commit 1c20a493ca

View File

@ -28,7 +28,7 @@
#include <asm/arch/smc.h>
#define DRV_NAME "pata_at32"
#define DRV_VERSION "0.0.2"
#define DRV_VERSION "0.0.3"
/*
* CompactFlash controller memory layout relative to the base address:
@ -64,6 +64,8 @@
* Mode 2 | 8.3 | 240 ns | 0x07
* Mode 3 | 11.1 | 180 ns | 0x0f
* Mode 4 | 16.7 | 120 ns | 0x1f
*
* Alter PIO_MASK below according to table to set maximal PIO mode.
*/
#define PIO_MASK (0x1f)
@ -85,36 +87,40 @@ struct at32_ide_info {
*/
static int pata_at32_setup_timing(struct device *dev,
struct at32_ide_info *info,
const struct ata_timing *timing)
const struct ata_timing *ata)
{
/* These two values are found through testing */
const int min_recover = 25;
const int ncs_hold = 15;
struct smc_config *smc = &info->smc;
struct smc_timing timing;
int active;
int recover;
memset(&timing, 0, sizeof(struct smc_timing));
/* Total cycle time */
smc->read_cycle = timing->cyc8b;
timing.read_cycle = ata->cyc8b;
/* DIOR <= CFIOR timings */
smc->nrd_setup = timing->setup;
smc->nrd_pulse = timing->act8b;
timing.nrd_setup = ata->setup;
timing.nrd_pulse = ata->act8b;
timing.nrd_recover = ata->rec8b;
/* Compute recover, extend total cycle if needed */
active = smc->nrd_setup + smc->nrd_pulse;
/* Convert nanosecond timing to clock cycles */
smc_set_timing(smc, &timing);
/* Add one extra cycle setup due to signal ring */
smc->nrd_setup = smc->nrd_setup + 1;
active = smc->nrd_setup + smc->nrd_pulse;
recover = smc->read_cycle - active;
if (recover < min_recover) {
smc->read_cycle = active + min_recover;
recover = min_recover;
}
/* Need at least two cycles recovery */
if (recover < 2)
smc->read_cycle = active + 2;
/* (CS0, CS1, DIR, OE) <= (CFCE1, CFCE2, CFRNW, NCSX) timings */
smc->ncs_read_setup = 0;
smc->ncs_read_pulse = active + ncs_hold;
smc->ncs_read_setup = 1;
smc->ncs_read_pulse = smc->read_cycle - 2;
/* Write timings same as read timings */
smc->write_cycle = smc->read_cycle;
@ -123,11 +129,13 @@ static int pata_at32_setup_timing(struct device *dev,
smc->ncs_write_setup = smc->ncs_read_setup;
smc->ncs_write_pulse = smc->ncs_read_pulse;
/* Do some debugging output */
dev_dbg(dev, "SMC: C=%d S=%d P=%d R=%d NCSS=%d NCSP=%d NCSR=%d\n",
/* Do some debugging output of ATA and SMC timings */
dev_dbg(dev, "ATA: C=%d S=%d P=%d R=%d\n",
ata->cyc8b, ata->setup, ata->act8b, ata->rec8b);
dev_dbg(dev, "SMC: C=%d S=%d P=%d NS=%d NP=%d\n",
smc->read_cycle, smc->nrd_setup, smc->nrd_pulse,
recover, smc->ncs_read_setup, smc->ncs_read_pulse,
smc->read_cycle - smc->ncs_read_pulse);
smc->ncs_read_setup, smc->ncs_read_pulse);
/* Finally, configure the SMC */
return smc_set_configuration(info->cs, smc);
@ -182,7 +190,6 @@ static struct scsi_host_template at32_sht = {
};
static struct ata_port_operations at32_port_ops = {
.port_disable = ata_port_disable,
.set_piomode = pata_at32_set_piomode,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
@ -203,7 +210,6 @@ static struct ata_port_operations at32_port_ops = {
.irq_clear = pata_at32_irq_clear,
.irq_on = ata_irq_on,
.irq_ack = ata_irq_ack,
.port_start = ata_sff_port_start,
};
@ -223,8 +229,7 @@ static int __init pata_at32_init_one(struct device *dev,
/* Setup ATA bindings */
ap->ops = &at32_port_ops;
ap->pio_mask = PIO_MASK;
ap->flags = ATA_FLAG_MMIO | ATA_FLAG_SLAVE_POSS
| ATA_FLAG_PIO_POLLING;
ap->flags |= ATA_FLAG_MMIO | ATA_FLAG_SLAVE_POSS;
/*
* Since all 8-bit taskfile transfers has to go on the lower
@ -357,12 +362,12 @@ static int __init pata_at32_probe(struct platform_device *pdev)
info->smc.tdf_mode = 0; /* TDF optimization disabled */
info->smc.tdf_cycles = 0; /* No TDF wait cycles */
/* Setup ATA timing */
/* Setup SMC to ATA timing */
ret = pata_at32_setup_timing(dev, info, &initial_timing);
if (ret)
goto err_setup_timing;
/* Setup ATA addresses */
/* Map ATA address space */
ret = -ENOMEM;
info->ide_addr = devm_ioremap(dev, info->res_ide.start, 16);
info->alt_addr = devm_ioremap(dev, info->res_alt.start, 16);
@ -373,7 +378,7 @@ static int __init pata_at32_probe(struct platform_device *pdev)
pata_at32_debug_bus(dev, info);
#endif
/* Register ATA device */
/* Setup and register ATA device */
ret = pata_at32_init_one(dev, info);
if (ret)
goto err_ata_device;