soc: devicetree updates for 6.10, part 1
The updates this time are a bit smaller than most times, mainly because
it is not totally dominated by new Qualcomm hardware support. Instead,
we larger than average updates for Rockchips, NXP, Allwinner and TI.
The only two new SoCs this time are both from NXP and are minor variants
of already supported ones.
The updates for aspeed, amlogic and mediatek came a little late, so
I'm saving those for part 2 in a few days if everything turns out fine.
New machines this time contain:
- two Broadcom SoC based wireless routers from Asus
- Five allwinner based consumer devices for gaming, set-top-box and
eboot reader applications
- Three older phones based on Qualcomm chips, plus the more recent
Sony Xperia 1 V
- 14 industrial and embedded boards based on NXP i.MX6, i.MX8,
layerscape and s32g3 SoCs
- six rockchips boards including another handheld game console
and a few single-board computers
On top of these, we have the usual cleanups for dtc warnings and
updates to add more features to already merged machines.
-----BEGIN PGP SIGNATURE-----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=SnV4
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC devicetree updates from Arnd Bergmann:
"The updates this time are a bit smaller than most times, mainly
because it is not totally dominated by new Qualcomm hardware support.
Instead, we larger than average updates for Rockchips, NXP, Allwinner
and TI. The only two new SoCs this time are both from NXP and are
minor variants of already supported ones.
The updates for aspeed, amlogic and mediatek came a little late, so
I'm saving those for part 2 in a few days if everything turns out
fine.
New machines this time contain:
- two Broadcom SoC based wireless routers from Asus
- Five allwinner based consumer devices for gaming, set-top-box and
eboot reader applications
- Three older phones based on Qualcomm chips, plus the more recent
Sony Xperia 1 V
- 14 industrial and embedded boards based on NXP i.MX6, i.MX8,
layerscape and s32g3 SoCs
- six rockchips boards including another handheld game console and a
few single-board computers
On top of these, we have the usual cleanups for dtc warnings and
updates to add more features to already merged machines"
* tag 'soc-dt-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (612 commits)
arm64: dts: marvell: espressobin-ultra: fix Ethernet Switch unit address
arm64: dts: marvell: turris-mox: drop unneeded flash address/size-cells
arm64: dts: marvell: eDPU: drop redundant address/size-cells
arm64: dts: qcom: pm6150: correct USB VBUS regulator compatible
arm64: dts: rockchip: add rk3588 pcie and php IOMMUs
arm64: dts: rockchip: enable onboard spi flash for rock-3a
arm64: dts: rockchip: add USB-C support to rk3588s-orangepi-5
arm64: dts: rockchip: Enable GPU on Orange Pi 5
arm64: dts: rockchip: enable GPU on khadas-edge2
arm64: dts: rockchip: Add USB3 on Edgeble NCM6A-IO board
arm64: dts: rockchip: Support poweroff on Edgeble Neural Compute Module
arm64: dts: rockchip: Add Radxa ROCK 3C
dt-bindings: arm: rockchip: add Radxa ROCK 3C
arm64: dts: exynos: gs101: specify empty clocks for remaining pinctrl
arm64: dts: exynos: gs101: specify bus clock for pinctrl_hsi2
arm64: dts: exynos: gs101: specify bus clock for pinctrl_peric[01]
arm64: dts: exynos: gs101: specify bus clock for pinctrl (far) alive
arm64: dts: Add/fix /memory node unit-addresses
arm64: dts: qcom: qcs404: fix bluetooth device address
arm64: dts: qcom: sc8280xp-x13s: enable USB MP and fingerprint reader
...
This commit is contained in:
Linus Torvalds
commit
6c60000f0b
@ -53,6 +53,7 @@ properties:
|
||||
- description: BCM4709 based boards
|
||||
items:
|
||||
- enum:
|
||||
- asus,rt-ac3200
|
||||
- asus,rt-ac87u
|
||||
- buffalo,wxr-1900dhp
|
||||
- linksys,ea9200
|
||||
@ -67,6 +68,7 @@ properties:
|
||||
items:
|
||||
- enum:
|
||||
- asus,rt-ac3100
|
||||
- asus,rt-ac5300
|
||||
- asus,rt-ac88u
|
||||
- dlink,dir-885l
|
||||
- dlink,dir-890l
|
||||
|
||||
@ -46,6 +46,30 @@ properties:
|
||||
- compatible
|
||||
- "#clock-cells"
|
||||
|
||||
gpio:
|
||||
type: object
|
||||
additionalProperties: false
|
||||
|
||||
properties:
|
||||
compatible:
|
||||
const: raspberrypi,firmware-gpio
|
||||
|
||||
gpio-controller: true
|
||||
|
||||
"#gpio-cells":
|
||||
const: 2
|
||||
description:
|
||||
The first cell is the pin number, and the second cell is used to
|
||||
specify the gpio polarity (GPIO_ACTIVE_HIGH or GPIO_ACTIVE_LOW).
|
||||
|
||||
gpio-line-names:
|
||||
minItems: 8
|
||||
|
||||
required:
|
||||
- compatible
|
||||
- gpio-controller
|
||||
- "#gpio-cells"
|
||||
|
||||
reset:
|
||||
type: object
|
||||
additionalProperties: false
|
||||
@ -96,6 +120,12 @@ examples:
|
||||
#clock-cells = <1>;
|
||||
};
|
||||
|
||||
expgpio: gpio {
|
||||
compatible = "raspberrypi,firmware-gpio";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
};
|
||||
|
||||
reset: reset {
|
||||
compatible = "raspberrypi,firmware-reset";
|
||||
#reset-cells = <1>;
|
||||
|
||||
@ -813,6 +813,14 @@ properties:
|
||||
- const: tq,imx6ull-tqma6ull2l # MCIMX6Y2, LGA SoM variant
|
||||
- const: fsl,imx6ull
|
||||
|
||||
- description: Seeed Stuido i.MX6ULL SoM on dev boards
|
||||
items:
|
||||
- enum:
|
||||
- seeed,imx6ull-seeed-npi-emmc
|
||||
- seeed,imx6ull-seeed-npi-nand
|
||||
- const: seeed,imx6ull-seeed-npi
|
||||
- const: fsl,imx6ull
|
||||
|
||||
- description: i.MX6ULZ based Boards
|
||||
items:
|
||||
- enum:
|
||||
@ -1050,6 +1058,7 @@ properties:
|
||||
- enum:
|
||||
- beacon,imx8mp-beacon-kit # i.MX8MP Beacon Development Kit
|
||||
- dmo,imx8mp-data-modul-edm-sbc # i.MX8MP eDM SBC
|
||||
- emcraft,imx8mp-navqp # i.MX8MP Emcraft Systems NavQ+ Kit
|
||||
- fsl,imx8mp-evk # i.MX8MP EVK Board
|
||||
- gateworks,imx8mp-gw71xx-2x # i.MX8MP Gateworks Board
|
||||
- gateworks,imx8mp-gw72xx-2x # i.MX8MP Gateworks Board
|
||||
@ -1218,7 +1227,6 @@ properties:
|
||||
- enum:
|
||||
- einfochips,imx8qxp-ai_ml # i.MX8QXP AI_ML Board
|
||||
- fsl,imx8qxp-mek # i.MX8QXP MEK Board
|
||||
- toradex,colibri-imx8x # Colibri iMX8X Modules
|
||||
- const: fsl,imx8qxp
|
||||
|
||||
- description: i.MX8DXL based Boards
|
||||
@ -1227,7 +1235,7 @@ properties:
|
||||
- fsl,imx8dxl-evk # i.MX8DXL EVK Board
|
||||
- const: fsl,imx8dxl
|
||||
|
||||
- description: i.MX8QXP Boards with Toradex Colibri iMX8X Modules
|
||||
- description: i.MX8QXP/i.MX8DX Boards with Toradex Colibri iMX8X Modules
|
||||
items:
|
||||
- enum:
|
||||
- toradex,colibri-imx8x-aster # Colibri iMX8X Module on Aster Board
|
||||
@ -1235,7 +1243,9 @@ properties:
|
||||
- toradex,colibri-imx8x-iris # Colibri iMX8X Module on Iris Board
|
||||
- toradex,colibri-imx8x-iris-v2 # Colibri iMX8X Module on Iris Board V2
|
||||
- const: toradex,colibri-imx8x
|
||||
- const: fsl,imx8qxp
|
||||
- enum:
|
||||
- fsl,imx8qxp
|
||||
- fsl,imx8dx
|
||||
|
||||
- description:
|
||||
TQMa8Xx is a series of SOM featuring NXP i.MX8X system-on-chip
|
||||
@ -1536,6 +1546,12 @@ properties:
|
||||
- nxp,s32g274a-rdb2
|
||||
- const: nxp,s32g2
|
||||
|
||||
- description: S32G3 based Boards
|
||||
items:
|
||||
- enum:
|
||||
- nxp,s32g399a-rdb3
|
||||
- const: nxp,s32g3
|
||||
|
||||
- description: S32V234 based Boards
|
||||
items:
|
||||
- enum:
|
||||
|
||||
@ -61,10 +61,6 @@ properties:
|
||||
mboxes:
|
||||
minItems: 2
|
||||
|
||||
ti,system-reboot-controller:
|
||||
description: Determines If system reboot can be triggered by SoC reboot
|
||||
type: boolean
|
||||
|
||||
ti,host-id:
|
||||
$ref: /schemas/types.yaml#/definitions/uint32
|
||||
description: |
|
||||
@ -94,7 +90,6 @@ examples:
|
||||
- |
|
||||
pmmc: system-controller@2921800 {
|
||||
compatible = "ti,k2g-sci";
|
||||
ti,system-reboot-controller;
|
||||
mbox-names = "rx", "tx";
|
||||
mboxes = <&msgmgr 5 2>,
|
||||
<&msgmgr 0 0>;
|
||||
|
||||
@ -137,6 +137,7 @@ properties:
|
||||
- microsoft,dempsey
|
||||
- microsoft,makepeace
|
||||
- microsoft,moneypenny
|
||||
- motorola,falcon
|
||||
- samsung,s3ve3g
|
||||
- const: qcom,msm8226
|
||||
|
||||
@ -184,13 +185,16 @@ properties:
|
||||
- oneplus,bacon
|
||||
- samsung,klte
|
||||
- sony,xperia-castor
|
||||
- sony,xperia-leo
|
||||
- const: qcom,msm8974pro
|
||||
- const: qcom,msm8974
|
||||
|
||||
- items:
|
||||
- const: qcom,msm8916-mtp
|
||||
- const: qcom,msm8916-mtp/1
|
||||
- const: qcom,msm8916
|
||||
- enum:
|
||||
- samsung,kltechn
|
||||
- const: samsung,klte
|
||||
- const: qcom,msm8974pro
|
||||
- const: qcom,msm8974
|
||||
|
||||
- items:
|
||||
- enum:
|
||||
@ -200,6 +204,8 @@ properties:
|
||||
- gplus,fl8005a
|
||||
- huawei,g7
|
||||
- longcheer,l8910
|
||||
- longcheer,l8150
|
||||
- qcom,msm8916-mtp
|
||||
- samsung,a3u-eur
|
||||
- samsung,a5u-eur
|
||||
- samsung,e5
|
||||
@ -220,11 +226,6 @@ properties:
|
||||
- yiming,uz801-v3
|
||||
- const: qcom,msm8916
|
||||
|
||||
- items:
|
||||
- const: longcheer,l8150
|
||||
- const: qcom,msm8916-v1-qrd/9-v1
|
||||
- const: qcom,msm8916
|
||||
|
||||
- items:
|
||||
- enum:
|
||||
- motorola,potter
|
||||
@ -1003,6 +1004,7 @@ properties:
|
||||
- qcom,sm8550-hdk
|
||||
- qcom,sm8550-mtp
|
||||
- qcom,sm8550-qrd
|
||||
- sony,pdx234
|
||||
- const: qcom,sm8550
|
||||
|
||||
- items:
|
||||
|
||||
@ -49,6 +49,11 @@ properties:
|
||||
- anbernic,rg-arc-s
|
||||
- const: rockchip,rk3566
|
||||
|
||||
- description: ArmSoM Sige7 board
|
||||
items:
|
||||
- const: armsom,sige7
|
||||
- const: rockchip,rk3588
|
||||
|
||||
- description: Asus Tinker board
|
||||
items:
|
||||
- const: asus,rk3288-tinker
|
||||
@ -198,6 +203,13 @@ properties:
|
||||
- const: firefly,rk3568-roc-pc
|
||||
- const: rockchip,rk3568
|
||||
|
||||
- description: Forlinx FET3588-C SoM
|
||||
items:
|
||||
- enum:
|
||||
- forlinx,ok3588-c
|
||||
- const: forlinx,fet3588-c
|
||||
- const: rockchip,rk3588
|
||||
|
||||
- description: FriendlyElec NanoPi R2 series boards
|
||||
items:
|
||||
- enum:
|
||||
@ -236,6 +248,11 @@ properties:
|
||||
- const: friendlyarm,nanopc-t6
|
||||
- const: rockchip,rk3588
|
||||
|
||||
- description: GameForce Chi
|
||||
items:
|
||||
- const: gameforce,chi
|
||||
- const: rockchip,rk3326
|
||||
|
||||
- description: GeekBuying GeekBox
|
||||
items:
|
||||
- const: geekbuying,geekbox
|
||||
@ -631,7 +648,7 @@ properties:
|
||||
- const: phytec,rk3288-phycore-som
|
||||
- const: rockchip,rk3288
|
||||
|
||||
- description: Pine64 PinebookPro
|
||||
- description: Pine64 Pinebook Pro
|
||||
items:
|
||||
- const: pine64,pinebook-pro
|
||||
- const: rockchip,rk3399
|
||||
@ -644,7 +661,7 @@ properties:
|
||||
- const: pine64,pinenote
|
||||
- const: rockchip,rk3566
|
||||
|
||||
- description: Pine64 PinePhonePro
|
||||
- description: Pine64 PinePhone Pro
|
||||
items:
|
||||
- const: pine64,pinephone-pro
|
||||
- const: rockchip,rk3399
|
||||
@ -682,7 +699,7 @@ properties:
|
||||
- const: pine64,quartzpro64
|
||||
- const: rockchip,rk3588
|
||||
|
||||
- description: Pine64 SoQuartz SoM
|
||||
- description: Pine64 SOQuartz
|
||||
items:
|
||||
- enum:
|
||||
- pine64,soquartz-blade
|
||||
@ -700,12 +717,17 @@ properties:
|
||||
- powkiddy,x55
|
||||
- const: rockchip,rk3566
|
||||
|
||||
- description: Protonic MECSBC board
|
||||
items:
|
||||
- const: prt,mecsbc
|
||||
- const: rockchip,rk3568
|
||||
|
||||
- description: QNAP TS-433-4G 4-Bay NAS
|
||||
items:
|
||||
- const: qnap,ts433
|
||||
- const: rockchip,rk3568
|
||||
|
||||
- description: Radxa Compute Module 3(CM3)
|
||||
- description: Radxa Compute Module 3 (CM3)
|
||||
items:
|
||||
- enum:
|
||||
- radxa,cm3-io
|
||||
@ -767,22 +789,27 @@ properties:
|
||||
- const: radxa,rockpis
|
||||
- const: rockchip,rk3308
|
||||
|
||||
- description: Radxa Rock2 Square
|
||||
- description: Radxa Rock 2 Square
|
||||
items:
|
||||
- const: radxa,rock2-square
|
||||
- const: rockchip,rk3288
|
||||
|
||||
- description: Radxa ROCK3 Model A
|
||||
- description: Radxa ROCK 3A
|
||||
items:
|
||||
- const: radxa,rock3a
|
||||
- const: rockchip,rk3568
|
||||
|
||||
- description: Radxa ROCK 5 Model A
|
||||
- description: Radxa ROCK 3C
|
||||
items:
|
||||
- const: radxa,rock-3c
|
||||
- const: rockchip,rk3566
|
||||
|
||||
- description: Radxa ROCK 5A
|
||||
items:
|
||||
- const: radxa,rock-5a
|
||||
- const: rockchip,rk3588s
|
||||
|
||||
- description: Radxa ROCK 5 Model B
|
||||
- description: Radxa ROCK 5B
|
||||
items:
|
||||
- const: radxa,rock-5b
|
||||
- const: rockchip,rk3588
|
||||
@ -927,6 +954,11 @@ properties:
|
||||
- const: turing,rk1
|
||||
- const: rockchip,rk3588
|
||||
|
||||
- description: WolfVision PF5 mainboard
|
||||
items:
|
||||
- const: wolfvision,rk3568-pf5
|
||||
- const: rockchip,rk3568
|
||||
|
||||
- description: Xunlong Orange Pi 5 Plus
|
||||
items:
|
||||
- const: xunlong,orangepi-5-plus
|
||||
|
||||
@ -56,6 +56,21 @@ properties:
|
||||
- const: anbernic,rg-nano
|
||||
- const: allwinner,sun8i-v3s
|
||||
|
||||
- description: Anbernic RG35XX (2024)
|
||||
- items:
|
||||
- const: anbernic,rg35xx-2024
|
||||
- const: allwinner,sun50i-h700
|
||||
|
||||
- description: Anbernic RG35XX Plus
|
||||
- items:
|
||||
- const: anbernic,rg35xx-plus
|
||||
- const: allwinner,sun50i-h700
|
||||
|
||||
- description: Anbernic RG35XX H
|
||||
- items:
|
||||
- const: anbernic,rg35xx-h
|
||||
- const: allwinner,sun50i-h700
|
||||
|
||||
- description: Amarula A64 Relic
|
||||
items:
|
||||
- const: amarula,a64-relic
|
||||
@ -774,6 +789,11 @@ properties:
|
||||
- const: pocketbook,touch-lux-3
|
||||
- const: allwinner,sun5i-a13
|
||||
|
||||
- description: PocketBook 614 Plus
|
||||
items:
|
||||
- const: pocketbook,614-plus
|
||||
- const: allwinner,sun5i-a13
|
||||
|
||||
- description: Point of View Protab2-IPS9
|
||||
items:
|
||||
- const: pov,protab2-ips9
|
||||
@ -860,6 +880,11 @@ properties:
|
||||
- const: allwinner,sl631
|
||||
- const: allwinner,sun8i-v3
|
||||
|
||||
- description: Tanix TX1
|
||||
items:
|
||||
- const: oranth,tanix-tx1
|
||||
- const: allwinner,sun50i-h616
|
||||
|
||||
- description: Tanix TX6
|
||||
items:
|
||||
- const: oranth,tanix-tx6
|
||||
|
||||
@ -30,16 +30,18 @@ properties:
|
||||
- google,gs101-cmu-top
|
||||
- google,gs101-cmu-apm
|
||||
- google,gs101-cmu-misc
|
||||
- google,gs101-cmu-hsi0
|
||||
- google,gs101-cmu-hsi2
|
||||
- google,gs101-cmu-peric0
|
||||
- google,gs101-cmu-peric1
|
||||
|
||||
clocks:
|
||||
minItems: 1
|
||||
maxItems: 3
|
||||
maxItems: 5
|
||||
|
||||
clock-names:
|
||||
minItems: 1
|
||||
maxItems: 3
|
||||
maxItems: 5
|
||||
|
||||
"#clock-cells":
|
||||
const: 1
|
||||
@ -72,6 +74,55 @@ allOf:
|
||||
items:
|
||||
- const: oscclk
|
||||
|
||||
- if:
|
||||
properties:
|
||||
compatible:
|
||||
contains:
|
||||
const: google,gs101-cmu-hsi0
|
||||
|
||||
then:
|
||||
properties:
|
||||
clocks:
|
||||
items:
|
||||
- description: External reference clock (24.576 MHz)
|
||||
- description: HSI0 bus clock (from CMU_TOP)
|
||||
- description: DPGTC (from CMU_TOP)
|
||||
- description: USB DRD controller clock (from CMU_TOP)
|
||||
- description: USB Display Port debug clock (from CMU_TOP)
|
||||
|
||||
clock-names:
|
||||
items:
|
||||
- const: oscclk
|
||||
- const: bus
|
||||
- const: dpgtc
|
||||
- const: usb31drd
|
||||
- const: usbdpdbg
|
||||
|
||||
- if:
|
||||
properties:
|
||||
compatible:
|
||||
contains:
|
||||
enum:
|
||||
- google,gs101-cmu-hsi2
|
||||
|
||||
then:
|
||||
properties:
|
||||
clocks:
|
||||
items:
|
||||
- description: External reference clock (24.576 MHz)
|
||||
- description: High Speed Interface bus clock (from CMU_TOP)
|
||||
- description: High Speed Interface pcie clock (from CMU_TOP)
|
||||
- description: High Speed Interface ufs clock (from CMU_TOP)
|
||||
- description: High Speed Interface mmc clock (from CMU_TOP)
|
||||
|
||||
clock-names:
|
||||
items:
|
||||
- const: oscclk
|
||||
- const: bus
|
||||
- const: pcie
|
||||
- const: ufs
|
||||
- const: mmc
|
||||
|
||||
- if:
|
||||
properties:
|
||||
compatible:
|
||||
|
||||
@ -348,15 +348,6 @@ properties:
|
||||
# Yes Optoelectronics YTC700TLAG-05-201C 7" TFT LCD panel
|
||||
- yes-optoelectronics,ytc700tlag-05-201c
|
||||
|
||||
backlight: true
|
||||
ddc-i2c-bus: true
|
||||
enable-gpios: true
|
||||
port: true
|
||||
power-supply: true
|
||||
no-hpd: true
|
||||
hpd-gpios: true
|
||||
data-mapping: true
|
||||
|
||||
if:
|
||||
not:
|
||||
properties:
|
||||
@ -367,7 +358,7 @@ then:
|
||||
properties:
|
||||
data-mapping: false
|
||||
|
||||
additionalProperties: false
|
||||
unevaluatedProperties: false
|
||||
|
||||
required:
|
||||
- compatible
|
||||
|
||||
@ -177,6 +177,15 @@ allOf:
|
||||
|
||||
required:
|
||||
- reg-names
|
||||
- if:
|
||||
properties:
|
||||
compatible:
|
||||
contains:
|
||||
enum:
|
||||
- nvidia,tegra194-host1x
|
||||
then:
|
||||
properties:
|
||||
dma-coherent: true
|
||||
- if:
|
||||
properties:
|
||||
compatible:
|
||||
@ -226,6 +235,8 @@ allOf:
|
||||
use. Should be a mapping of IDs 0..n to IOMMU entries corresponding to
|
||||
usable stream IDs.
|
||||
|
||||
dma-coherent: true
|
||||
|
||||
required:
|
||||
- reg-names
|
||||
|
||||
|
||||
@ -1,30 +0,0 @@
|
||||
Raspberry Pi GPIO expander
|
||||
|
||||
The Raspberry Pi 3 GPIO expander is controlled by the VC4 firmware. The
|
||||
firmware exposes a mailbox interface that allows the ARM core to control the
|
||||
GPIO lines on the expander.
|
||||
|
||||
The Raspberry Pi GPIO expander node must be a child node of the Raspberry Pi
|
||||
firmware node.
|
||||
|
||||
Required properties:
|
||||
|
||||
- compatible : Should be "raspberrypi,firmware-gpio"
|
||||
- gpio-controller : Marks the device node as a gpio controller
|
||||
- #gpio-cells : Should be two. The first cell is the pin number, and
|
||||
the second cell is used to specify the gpio polarity:
|
||||
0 = active high
|
||||
1 = active low
|
||||
|
||||
Example:
|
||||
|
||||
firmware: firmware-rpi {
|
||||
compatible = "raspberrypi,bcm2835-firmware";
|
||||
mboxes = <&mailbox>;
|
||||
|
||||
expgpio: gpio {
|
||||
compatible = "raspberrypi,firmware-gpio";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
};
|
||||
};
|
||||
@ -30,6 +30,10 @@ properties:
|
||||
clocks:
|
||||
maxItems: 1
|
||||
|
||||
access-controllers:
|
||||
minItems: 1
|
||||
maxItems: 2
|
||||
|
||||
required:
|
||||
- compatible
|
||||
- reg
|
||||
|
||||
@ -58,20 +58,6 @@ patternProperties:
|
||||
required:
|
||||
- compatible
|
||||
|
||||
allOf:
|
||||
- if:
|
||||
not:
|
||||
properties:
|
||||
compatible:
|
||||
contains:
|
||||
enum:
|
||||
- qcom,sm8450-pmic-glink
|
||||
- qcom,sm8550-pmic-glink
|
||||
- qcom,x1e80100-pmic-glink
|
||||
then:
|
||||
properties:
|
||||
orientation-gpios: false
|
||||
|
||||
additionalProperties: false
|
||||
|
||||
examples:
|
||||
|
||||
@ -0,0 +1,51 @@
|
||||
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
|
||||
%YAML 1.2
|
||||
---
|
||||
$id: http://devicetree.org/schemas/soc/renesas/renesas,r9a09g057-sys.yaml#
|
||||
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
||||
|
||||
title: Renesas RZ/V2H(P) System Controller (SYS)
|
||||
|
||||
maintainers:
|
||||
- Geert Uytterhoeven <geert+renesas@glider.be>
|
||||
|
||||
description: |
|
||||
The RZ/V2H(P) SYS (System Controller) controls the overall
|
||||
configuration of the LSI and supports the following functions,
|
||||
- Trust zone control
|
||||
- Extend access by specific masters to address beyond 4GB space
|
||||
- GBETH configuration
|
||||
- Control of settings and states of SRAM/PCIe/CM33/CA55/CR8/xSPI/ADC/TSU
|
||||
- LSI version
|
||||
- WDT stop control
|
||||
- General registers
|
||||
|
||||
properties:
|
||||
compatible:
|
||||
const: renesas,r9a09g057-sys
|
||||
|
||||
reg:
|
||||
maxItems: 1
|
||||
|
||||
clocks:
|
||||
maxItems: 1
|
||||
|
||||
resets:
|
||||
maxItems: 1
|
||||
|
||||
required:
|
||||
- compatible
|
||||
- reg
|
||||
- clocks
|
||||
- resets
|
||||
|
||||
additionalProperties: false
|
||||
|
||||
examples:
|
||||
- |
|
||||
sys: system-controller@10430000 {
|
||||
compatible = "renesas,r9a09g057-sys";
|
||||
reg = <0x10430000 0x10000>;
|
||||
clocks = <&cpg 1>;
|
||||
resets = <&cpg 1>;
|
||||
};
|
||||
@ -513,6 +513,14 @@ properties:
|
||||
- renesas,rzv2mevk2 # RZ/V2M Eval Board v2.0
|
||||
- const: renesas,r9a09g011
|
||||
|
||||
- description: RZ/V2H(P) (R9A09G057)
|
||||
items:
|
||||
- enum:
|
||||
- renesas,r9a09g057h41 # RZ/V2H
|
||||
- renesas,r9a09g057h42 # RZ/V2H with Mali-G31 support
|
||||
- renesas,r9a09g057h44 # RZ/V2HP with Mali-G31 + Mali-C55 support
|
||||
- const: renesas,r9a09g057
|
||||
|
||||
additionalProperties: true
|
||||
|
||||
...
|
||||
|
||||
@ -15,6 +15,7 @@ properties:
|
||||
- items:
|
||||
- enum:
|
||||
- google,gs101-apm-sysreg
|
||||
- google,gs101-hsi2-sysreg
|
||||
- google,gs101-peric0-sysreg
|
||||
- google,gs101-peric1-sysreg
|
||||
- samsung,exynos3-sysreg
|
||||
@ -72,6 +73,7 @@ allOf:
|
||||
compatible:
|
||||
contains:
|
||||
enum:
|
||||
- google,gs101-hsi2-sysreg
|
||||
- google,gs101-peric0-sysreg
|
||||
- google,gs101-peric1-sysreg
|
||||
- samsung,exynos850-cmgp-sysreg
|
||||
|
||||
@ -33,6 +33,7 @@ properties:
|
||||
- fsl,imx7ulp-usbmisc
|
||||
- fsl,imx8mm-usbmisc
|
||||
- fsl,imx8mn-usbmisc
|
||||
- fsl,imx8ulp-usbmisc
|
||||
- const: fsl,imx7d-usbmisc
|
||||
- const: fsl,imx6q-usbmisc
|
||||
- items:
|
||||
|
||||
@ -151,6 +151,8 @@ patternProperties:
|
||||
description: ARM Ltd.
|
||||
"^armadeus,.*":
|
||||
description: ARMadeus Systems SARL
|
||||
"^armsom,.*":
|
||||
description: ArmSoM Technology Co., Ltd.
|
||||
"^arrow,.*":
|
||||
description: Arrow Electronics
|
||||
"^artesyn,.*":
|
||||
@ -438,6 +440,8 @@ patternProperties:
|
||||
description: Dongguan EmbedFire Electronic Technology Co., Ltd.
|
||||
"^embest,.*":
|
||||
description: Shenzhen Embest Technology Co., Ltd.
|
||||
"^emcraft,.*":
|
||||
description: Emcraft Systems
|
||||
"^emlid,.*":
|
||||
description: Emlid, Ltd.
|
||||
"^emmicro,.*":
|
||||
@ -1627,6 +1631,8 @@ patternProperties:
|
||||
description: Wondermedia Technologies, Inc.
|
||||
"^wobo,.*":
|
||||
description: Wobo
|
||||
"^wolfvision,.*":
|
||||
description: WolfVision GmbH
|
||||
"^x-powers,.*":
|
||||
description: X-Powers
|
||||
"^xen,.*":
|
||||
|
||||
@ -61,6 +61,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \
|
||||
sun5i-a13-olinuxino.dtb \
|
||||
sun5i-a13-olinuxino-micro.dtb \
|
||||
sun5i-a13-pocketbook-touch-lux-3.dtb \
|
||||
sun5i-a13-pocketbook-614-plus.dtb \
|
||||
sun5i-a13-q8-tablet.dtb \
|
||||
sun5i-a13-utoo-p66.dtb \
|
||||
sun5i-gr8-chip-pro.dtb \
|
||||
|
||||
218
arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
Normal file
218
arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
Normal file
@ -0,0 +1,218 @@
|
||||
// SPDX-License-Identifier: GPL-2.0+
|
||||
/*
|
||||
* Copyright 2024 Denis Burkov <hitechshell@mail.ru>
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
#include "sun5i-a13.dtsi"
|
||||
#include "sunxi-common-regulators.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/interrupt-controller/irq.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
model = "PocketBook 614 Plus";
|
||||
compatible = "pocketbook,614-plus", "allwinner,sun5i-a13";
|
||||
|
||||
aliases {
|
||||
serial0 = &uart1;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led-0 {
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
linux,default-trigger = "default-on";
|
||||
gpios = <&pio 4 8 GPIO_ACTIVE_LOW>; /* PE8 */
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
key-0 {
|
||||
label = "Right";
|
||||
linux,code = <KEY_NEXT>;
|
||||
gpios = <&pio 6 9 GPIO_ACTIVE_LOW>; /* PG9 */
|
||||
};
|
||||
|
||||
key-1 {
|
||||
label = "Left";
|
||||
linux,code = <KEY_PREVIOUS>;
|
||||
gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 */
|
||||
};
|
||||
};
|
||||
|
||||
reg_3v3_mmc0: regulator-mmc0 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vdd-mmc0";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
gpio = <&pio 4 4 GPIO_ACTIVE_LOW>; /* PE4 */
|
||||
vin-supply = <®_vcc3v3>;
|
||||
};
|
||||
};
|
||||
|
||||
&cpu0 {
|
||||
cpu-supply = <®_dcdc2>;
|
||||
};
|
||||
|
||||
&ehci0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
status = "okay";
|
||||
|
||||
axp209: pmic@34 {
|
||||
compatible = "x-powers,axp209";
|
||||
reg = <0x34>;
|
||||
interrupts = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
#include "axp209.dtsi"
|
||||
|
||||
&i2c1 {
|
||||
status = "okay";
|
||||
|
||||
pcf8563: rtc@51 {
|
||||
compatible = "nxp,pcf8563";
|
||||
reg = <0x51>;
|
||||
#clock-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&lradc {
|
||||
vref-supply = <®_ldo2>;
|
||||
status = "okay";
|
||||
|
||||
button-300 {
|
||||
label = "Down";
|
||||
linux,code = <KEY_DOWN>;
|
||||
channel = <0>;
|
||||
voltage = <300000>;
|
||||
};
|
||||
|
||||
button-700 {
|
||||
label = "Up";
|
||||
linux,code = <KEY_UP>;
|
||||
channel = <0>;
|
||||
voltage = <700000>;
|
||||
};
|
||||
|
||||
button-1000 {
|
||||
label = "Left";
|
||||
linux,code = <KEY_LEFT>;
|
||||
channel = <0>;
|
||||
voltage = <1000000>;
|
||||
};
|
||||
|
||||
button-1200 {
|
||||
label = "Menu";
|
||||
linux,code = <KEY_MENU>;
|
||||
channel = <0>;
|
||||
voltage = <1200000>;
|
||||
};
|
||||
|
||||
button-1500 {
|
||||
label = "Right";
|
||||
linux,code = <KEY_RIGHT>;
|
||||
channel = <0>;
|
||||
voltage = <1500000>;
|
||||
};
|
||||
};
|
||||
|
||||
&mmc0 {
|
||||
vmmc-supply = <®_3v3_mmc0>;
|
||||
bus-width = <4>;
|
||||
cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mmc2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&mmc2_4bit_pc_pins>;
|
||||
vmmc-supply = <®_vcc3v3>;
|
||||
bus-width = <4>;
|
||||
non-removable;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ohci0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&otg_sram {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
®_dcdc2 {
|
||||
regulator-always-on;
|
||||
regulator-min-microvolt = <1000000>;
|
||||
regulator-max-microvolt = <1500000>;
|
||||
regulator-name = "vdd-cpu";
|
||||
};
|
||||
|
||||
®_dcdc3 {
|
||||
regulator-always-on;
|
||||
regulator-min-microvolt = <1000000>;
|
||||
regulator-max-microvolt = <1400000>;
|
||||
regulator-name = "vdd-int-dll";
|
||||
};
|
||||
|
||||
®_ldo1 {
|
||||
regulator-name = "vdd-rtc";
|
||||
};
|
||||
|
||||
®_ldo2 {
|
||||
regulator-always-on;
|
||||
regulator-min-microvolt = <3000000>;
|
||||
regulator-max-microvolt = <3000000>;
|
||||
regulator-name = "avcc";
|
||||
};
|
||||
|
||||
®_usb0_vbus {
|
||||
status = "okay";
|
||||
gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
|
||||
};
|
||||
|
||||
®_usb1_vbus {
|
||||
gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart1_pg_pins>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_otg {
|
||||
dr_mode = "otg";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_power_supply {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&battery_power_supply {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbphy {
|
||||
usb0_id_det-gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
|
||||
usb0_vbus_det-gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>;
|
||||
usb0_vbus-supply = <®_usb0_vbus>;
|
||||
usb1_vbus-supply = <®_usb1_vbus>;
|
||||
status = "okay";
|
||||
};
|
||||
@ -62,14 +62,14 @@
|
||||
};
|
||||
|
||||
trips {
|
||||
cpu_alert0: cpu_alert0 {
|
||||
cpu_alert0: cpu-alert0 {
|
||||
/* milliCelsius */
|
||||
temperature = <85000>;
|
||||
hysteresis = <2000>;
|
||||
type = "passive";
|
||||
};
|
||||
|
||||
cpu_crit: cpu_crit {
|
||||
cpu_crit: cpu-crit {
|
||||
/* milliCelsius */
|
||||
temperature = <100000>;
|
||||
hysteresis = <2000>;
|
||||
|
||||
@ -77,7 +77,7 @@
|
||||
};
|
||||
};
|
||||
|
||||
mmc0_pwrseq: mmc0_pwrseq {
|
||||
mmc0_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&pio 1 10 GPIO_ACTIVE_LOW>; /* PB10 */
|
||||
};
|
||||
|
||||
@ -77,7 +77,7 @@
|
||||
};
|
||||
};
|
||||
|
||||
mmc0_pwrseq: mmc0_pwrseq {
|
||||
mmc0_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&pio 2 19 GPIO_ACTIVE_LOW>; /* PC19 */
|
||||
};
|
||||
|
||||
@ -109,7 +109,7 @@
|
||||
};
|
||||
};
|
||||
|
||||
reg_vga_3v3: vga_3v3_regulator {
|
||||
reg_vga_3v3: vga-3v3-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vga-3v3";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
@ -119,7 +119,7 @@
|
||||
gpio = <&pio 7 25 GPIO_ACTIVE_HIGH>; /* PH25 */
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 */
|
||||
};
|
||||
|
||||
@ -179,14 +179,14 @@
|
||||
};
|
||||
|
||||
trips {
|
||||
cpu_alert0: cpu_alert0 {
|
||||
cpu_alert0: cpu-alert0 {
|
||||
/* milliCelsius */
|
||||
temperature = <70000>;
|
||||
hysteresis = <2000>;
|
||||
type = "passive";
|
||||
};
|
||||
|
||||
cpu_crit: cpu_crit {
|
||||
cpu_crit: cpu-crit {
|
||||
/* milliCelsius */
|
||||
temperature = <100000>;
|
||||
hysteresis = <2000>;
|
||||
@ -1318,7 +1318,7 @@
|
||||
compatible = "allwinner,sun6i-a31-prcm";
|
||||
reg = <0x01f01400 0x200>;
|
||||
|
||||
ar100: ar100_clk {
|
||||
ar100: ar100-clk {
|
||||
compatible = "allwinner,sun6i-a31-ar100-clk";
|
||||
#clock-cells = <0>;
|
||||
clocks = <&rtc CLK_OSC32K>, <&osc24M>,
|
||||
@ -1327,7 +1327,7 @@
|
||||
clock-output-names = "ar100";
|
||||
};
|
||||
|
||||
ahb0: ahb0_clk {
|
||||
ahb0: ahb0-clk {
|
||||
compatible = "fixed-factor-clock";
|
||||
#clock-cells = <0>;
|
||||
clock-div = <1>;
|
||||
@ -1336,14 +1336,14 @@
|
||||
clock-output-names = "ahb0";
|
||||
};
|
||||
|
||||
apb0: apb0_clk {
|
||||
apb0: apb0-clk {
|
||||
compatible = "allwinner,sun6i-a31-apb0-clk";
|
||||
#clock-cells = <0>;
|
||||
clocks = <&ahb0>;
|
||||
clock-output-names = "apb0";
|
||||
};
|
||||
|
||||
apb0_gates: apb0_gates_clk {
|
||||
apb0_gates: apb0-gates-clk {
|
||||
compatible = "allwinner,sun6i-a31-apb0-gates-clk";
|
||||
#clock-cells = <1>;
|
||||
clocks = <&apb0>;
|
||||
@ -1353,14 +1353,14 @@
|
||||
"apb0_i2c";
|
||||
};
|
||||
|
||||
ir_clk: ir_clk {
|
||||
ir_clk: ir-clk {
|
||||
#clock-cells = <0>;
|
||||
compatible = "allwinner,sun4i-a10-mod0-clk";
|
||||
clocks = <&rtc CLK_OSC32K>, <&osc24M>;
|
||||
clock-output-names = "ir";
|
||||
};
|
||||
|
||||
apb0_rst: apb0_rst {
|
||||
apb0_rst: apb0-rst {
|
||||
compatible = "allwinner,sun6i-a31-clock-reset";
|
||||
#reset-cells = <1>;
|
||||
};
|
||||
|
||||
@ -75,7 +75,7 @@
|
||||
};
|
||||
};
|
||||
|
||||
mmc2_pwrseq: mmc2_pwrseq {
|
||||
mmc2_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&r_pio 0 8 GPIO_ACTIVE_LOW>; /* PL8 WIFI_EN */
|
||||
};
|
||||
|
||||
@ -86,7 +86,7 @@
|
||||
};
|
||||
};
|
||||
|
||||
mmc3_pwrseq: mmc3_pwrseq {
|
||||
mmc3_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 WL-PMU-EN */
|
||||
};
|
||||
|
||||
@ -96,7 +96,7 @@
|
||||
};
|
||||
};
|
||||
|
||||
mmc3_pwrseq: mmc3_pwrseq {
|
||||
mmc3_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&pio 7 9 GPIO_ACTIVE_LOW>; /* PH9 WIFI_EN */
|
||||
clocks = <&ccu CLK_OUT_A>;
|
||||
|
||||
@ -65,7 +65,7 @@
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
reg_mmc3_vdd: mmc3_vdd {
|
||||
reg_mmc3_vdd: regulator-mmc3-vdd {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "mmc3_vdd";
|
||||
regulator-min-microvolt = <3000000>;
|
||||
@ -74,7 +74,7 @@
|
||||
gpio = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
|
||||
};
|
||||
|
||||
reg_gmac_vdd: gmac_vdd {
|
||||
reg_gmac_vdd: regulator-gmac-vdd {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "gmac_vdd";
|
||||
regulator-min-microvolt = <3000000>;
|
||||
|
||||
@ -14,7 +14,7 @@
|
||||
model = "Olimex A20-Olimex-SOM-EVB-eMMC";
|
||||
compatible = "olimex,a20-olimex-som-evb-emmc", "allwinner,sun7i-a20";
|
||||
|
||||
mmc2_pwrseq: mmc2_pwrseq {
|
||||
mmc2_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-emmc";
|
||||
reset-gpios = <&pio 2 18 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
@ -13,7 +13,7 @@
|
||||
model = "Olimex A20-SOM204-EVB-eMMC";
|
||||
compatible = "olimex,a20-olimex-som204-evb-emmc", "allwinner,sun7i-a20";
|
||||
|
||||
mmc2_pwrseq: mmc2_pwrseq {
|
||||
mmc2_pwrseq: pwrseq-1 {
|
||||
compatible = "mmc-pwrseq-emmc";
|
||||
reset-gpios = <&pio 2 16 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
@ -65,7 +65,7 @@
|
||||
};
|
||||
};
|
||||
|
||||
rtl_pwrseq: rtl_pwrseq {
|
||||
rtl_pwrseq: pwrseq-0 {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&pio 6 9 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
@ -177,7 +177,7 @@
|
||||
non-removable;
|
||||
status = "okay";
|
||||
|
||||
rtl8723bs: sdio_wifi@1 {
|
||||
rtl8723bs: wifi@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
@ -82,7 +82,7 @@
|
||||
};
|
||||
};
|
||||
|
||||
reg_axp_ipsout: axp_ipsout {
|
||||
reg_axp_ipsout: regulator-axp-ipsout {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "axp-ipsout";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
|
||||
@ -60,7 +60,7 @@
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
mmc3_pwrseq: mmc3_pwrseq {
|
||||
mmc3_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&pio 7 9 GPIO_ACTIVE_LOW>; /* PH9 WIFI_EN */
|
||||
};
|
||||
|
||||
@ -153,14 +153,14 @@
|
||||
};
|
||||
|
||||
trips {
|
||||
cpu_alert0: cpu_alert0 {
|
||||
cpu_alert0: cpu-alert0 {
|
||||
/* milliCelsius */
|
||||
temperature = <75000>;
|
||||
hysteresis = <2000>;
|
||||
type = "passive";
|
||||
};
|
||||
|
||||
cpu_crit: cpu_crit {
|
||||
cpu_crit: cpu-crit {
|
||||
/* milliCelsius */
|
||||
temperature = <100000>;
|
||||
hysteresis = <2000>;
|
||||
|
||||
@ -108,7 +108,7 @@
|
||||
#size-cells = <1>;
|
||||
ranges;
|
||||
|
||||
osc24M: osc24M_clk {
|
||||
osc24M: osc24M-clk {
|
||||
#clock-cells = <0>;
|
||||
compatible = "fixed-clock";
|
||||
clock-frequency = <24000000>;
|
||||
@ -116,7 +116,7 @@
|
||||
clock-output-names = "osc24M";
|
||||
};
|
||||
|
||||
ext_osc32k: ext_osc32k_clk {
|
||||
ext_osc32k: ext-osc32k-clk {
|
||||
#clock-cells = <0>;
|
||||
compatible = "fixed-clock";
|
||||
clock-frequency = <32768>;
|
||||
@ -733,7 +733,7 @@
|
||||
compatible = "allwinner,sun8i-a23-prcm";
|
||||
reg = <0x01f01400 0x200>;
|
||||
|
||||
ar100: ar100_clk {
|
||||
ar100: ar100-clk {
|
||||
compatible = "fixed-factor-clock";
|
||||
#clock-cells = <0>;
|
||||
clock-div = <1>;
|
||||
@ -742,7 +742,7 @@
|
||||
clock-output-names = "ar100";
|
||||
};
|
||||
|
||||
ahb0: ahb0_clk {
|
||||
ahb0: ahb0-clk {
|
||||
compatible = "fixed-factor-clock";
|
||||
#clock-cells = <0>;
|
||||
clock-div = <1>;
|
||||
@ -751,14 +751,14 @@
|
||||
clock-output-names = "ahb0";
|
||||
};
|
||||
|
||||
apb0: apb0_clk {
|
||||
apb0: apb0-clk {
|
||||
compatible = "allwinner,sun8i-a23-apb0-clk";
|
||||
#clock-cells = <0>;
|
||||
clocks = <&ahb0>;
|
||||
clock-output-names = "apb0";
|
||||
};
|
||||
|
||||
apb0_gates: apb0_gates_clk {
|
||||
apb0_gates: apb0-gates-clk {
|
||||
compatible = "allwinner,sun8i-a23-apb0-gates-clk";
|
||||
#clock-cells = <1>;
|
||||
clocks = <&apb0>;
|
||||
@ -767,7 +767,7 @@
|
||||
"apb0_i2c";
|
||||
};
|
||||
|
||||
apb0_rst: apb0_rst {
|
||||
apb0_rst: apb0-rst {
|
||||
compatible = "allwinner,sun6i-a31-clock-reset";
|
||||
#reset-cells = <1>;
|
||||
};
|
||||
|
||||
@ -52,7 +52,7 @@
|
||||
ethernet0 = &esp8089;
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL6 */
|
||||
/* The esp8089 needs 200 ms after driving wifi-en high */
|
||||
@ -76,7 +76,7 @@
|
||||
non-removable;
|
||||
status = "okay";
|
||||
|
||||
esp8089: sdio_wifi@1 {
|
||||
esp8089: wifi@1 {
|
||||
compatible = "esp,esp8089";
|
||||
reg = <1>;
|
||||
esp,crystal-26M-en = <2>;
|
||||
|
||||
@ -52,7 +52,7 @@
|
||||
ethernet0 = &esp8089;
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL6 */
|
||||
/* The esp8089 needs 200 ms after driving wifi-en high */
|
||||
@ -69,7 +69,7 @@
|
||||
non-removable;
|
||||
status = "okay";
|
||||
|
||||
esp8089: sdio_wifi@1 {
|
||||
esp8089: wifi@1 {
|
||||
compatible = "esp,esp8089";
|
||||
reg = <1>;
|
||||
esp,crystal-26M-en = <2>;
|
||||
|
||||
@ -85,7 +85,7 @@
|
||||
non-removable;
|
||||
status = "okay";
|
||||
|
||||
rtl8703as: sdio_wifi@1 {
|
||||
rtl8703as: wifi@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
@ -78,7 +78,7 @@
|
||||
non-removable;
|
||||
status = "okay";
|
||||
|
||||
rtl8723bs: sdio_wifi@1 {
|
||||
rtl8723bs: wifi@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
@ -323,35 +323,35 @@
|
||||
};
|
||||
|
||||
trips {
|
||||
cpu_alert0: cpu_alert0 {
|
||||
cpu_alert0: cpu-alert0 {
|
||||
/* milliCelsius */
|
||||
temperature = <75000>;
|
||||
hysteresis = <2000>;
|
||||
type = "passive";
|
||||
};
|
||||
|
||||
gpu_alert0: gpu_alert0 {
|
||||
gpu_alert0: gpu-alert0 {
|
||||
/* milliCelsius */
|
||||
temperature = <85000>;
|
||||
hysteresis = <2000>;
|
||||
type = "passive";
|
||||
};
|
||||
|
||||
cpu_alert1: cpu_alert1 {
|
||||
cpu_alert1: cpu-alert1 {
|
||||
/* milliCelsius */
|
||||
temperature = <90000>;
|
||||
hysteresis = <2000>;
|
||||
type = "hot";
|
||||
};
|
||||
|
||||
gpu_alert1: gpu_alert1 {
|
||||
gpu_alert1: gpu-alert1 {
|
||||
/* milliCelsius */
|
||||
temperature = <95000>;
|
||||
hysteresis = <2000>;
|
||||
type = "hot";
|
||||
};
|
||||
|
||||
cpu_crit: cpu_crit {
|
||||
cpu_crit: cpu-crit {
|
||||
/* milliCelsius */
|
||||
temperature = <110000>;
|
||||
hysteresis = <2000>;
|
||||
|
||||
@ -95,7 +95,7 @@
|
||||
gpio = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
clocks = <&ac100_rtc 1>;
|
||||
clock-names = "ext_clock";
|
||||
|
||||
@ -144,7 +144,7 @@
|
||||
compatible = "linux,spdif-dit";
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
clocks = <&ac100_rtc 1>;
|
||||
clock-names = "ext_clock";
|
||||
|
||||
@ -123,7 +123,7 @@
|
||||
vin-supply = <®_vbat>;
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
|
||||
|
||||
|
||||
@ -164,7 +164,7 @@
|
||||
ranges;
|
||||
|
||||
/* TODO: PRCM block has a mux for this. */
|
||||
osc24M: osc24M_clk {
|
||||
osc24M: osc24M-clk {
|
||||
#clock-cells = <0>;
|
||||
compatible = "fixed-clock";
|
||||
clock-frequency = <24000000>;
|
||||
@ -177,14 +177,14 @@
|
||||
* It is an internal RC-based oscillator.
|
||||
* TODO: Its controls are in the PRCM block.
|
||||
*/
|
||||
osc16M: osc16M_clk {
|
||||
osc16M: osc16M-clk {
|
||||
#clock-cells = <0>;
|
||||
compatible = "fixed-clock";
|
||||
clock-frequency = <16000000>;
|
||||
clock-output-names = "osc16M";
|
||||
};
|
||||
|
||||
osc16Md512: osc16Md512_clk {
|
||||
osc16Md512: osc16Md512-clk {
|
||||
#clock-cells = <0>;
|
||||
compatible = "fixed-factor-clock";
|
||||
clock-div = <512>;
|
||||
@ -1127,7 +1127,7 @@
|
||||
#reset-cells = <1>;
|
||||
};
|
||||
|
||||
r_cpucfg@1f01c00 {
|
||||
cpucfg@1f01c00 {
|
||||
compatible = "allwinner,sun8i-a83t-r-cpucfg";
|
||||
reg = <0x1f01c00 0x400>;
|
||||
};
|
||||
|
||||
@ -103,7 +103,7 @@
|
||||
cpu-supply = <®_vcc1v2>;
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
|
||||
clocks = <&rtc CLK_OSC32K_FANOUT>;
|
||||
|
||||
@ -43,11 +43,12 @@
|
||||
/* Orange Pi R1 is based on Orange Pi Zero design */
|
||||
#include "sun8i-h2-plus-orangepi-zero.dts"
|
||||
|
||||
/delete-node/ ®_vcc_wifi;
|
||||
|
||||
/ {
|
||||
model = "Xunlong Orange Pi R1";
|
||||
compatible = "xunlong,orangepi-r1", "allwinner,sun8i-h2-plus";
|
||||
|
||||
/delete-node/ reg_vcc_wifi;
|
||||
|
||||
/*
|
||||
* Ths pin of this regulator is the same with the Wi-Fi extra
|
||||
@ -89,7 +90,7 @@
|
||||
vmmc-supply = <®_vcc3v3>;
|
||||
vqmmc-supply = <®_vcc3v3>;
|
||||
|
||||
rtl8189etv: sdio_wifi@1 {
|
||||
rtl8189etv: wifi@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
@ -80,7 +80,7 @@
|
||||
};
|
||||
};
|
||||
|
||||
reg_vcc_wifi: reg_vcc_wifi {
|
||||
reg_vcc_wifi: reg-vcc-wifi {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
@ -105,7 +105,7 @@
|
||||
states = <1100000 0>, <1300000 1>;
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>;
|
||||
post-power-on-delay-ms = <200>;
|
||||
@ -149,7 +149,7 @@
|
||||
* Explicitly define the sdio device, so that we can add an ethernet
|
||||
* alias for it (which e.g. makes u-boot set a mac-address).
|
||||
*/
|
||||
xr819: sdio_wifi@1 {
|
||||
xr819: wifi@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
@ -122,7 +122,7 @@
|
||||
compatible = "linux,spdif-dit";
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
|
||||
clocks = <&rtc CLK_OSC32K_FANOUT>;
|
||||
@ -185,7 +185,7 @@
|
||||
* Explicitly define the sdio device, so that we can add an ethernet
|
||||
* alias for it (which e.g. makes u-boot set a mac-address).
|
||||
*/
|
||||
sdiowifi: sdio_wifi@1 {
|
||||
sdiowifi: wifi@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
@ -87,7 +87,7 @@
|
||||
vin-supply = <®_vcc5v0>;
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
|
||||
clocks = <&rtc CLK_OSC32K_FANOUT>;
|
||||
@ -119,7 +119,7 @@
|
||||
non-removable;
|
||||
status = "okay";
|
||||
|
||||
sdio_wifi: sdio_wifi@1 {
|
||||
sdio_wifi: wifi@1 {
|
||||
reg = <1>;
|
||||
compatible = "brcm,bcm4329-fmac";
|
||||
interrupt-parent = <&pio>;
|
||||
|
||||
@ -62,7 +62,7 @@
|
||||
gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
|
||||
};
|
||||
@ -132,7 +132,7 @@
|
||||
non-removable;
|
||||
status = "okay";
|
||||
|
||||
sdio_wifi: sdio_wifi@1 {
|
||||
sdio_wifi: wifi@1 {
|
||||
reg = <1>;
|
||||
compatible = "brcm,bcm4329-fmac";
|
||||
interrupt-parent = <&pio>;
|
||||
|
||||
@ -73,7 +73,7 @@
|
||||
};
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
|
||||
};
|
||||
|
||||
@ -43,7 +43,7 @@
|
||||
<1300000 0x1>;
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
|
||||
clocks = <&rtc CLK_OSC32K_FANOUT>;
|
||||
|
||||
@ -105,7 +105,7 @@
|
||||
};
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 WIFI_EN */
|
||||
};
|
||||
@ -169,7 +169,7 @@
|
||||
* Explicitly define the sdio device, so that we can add an ethernet
|
||||
* alias for it (which e.g. makes u-boot set a mac-address).
|
||||
*/
|
||||
rtl8189: sdio_wifi@1 {
|
||||
rtl8189: wifi@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
@ -143,7 +143,7 @@
|
||||
* Explicitly define the sdio device, so that we can add an ethernet
|
||||
* alias for it (which e.g. makes u-boot set a mac-address).
|
||||
*/
|
||||
rtl8189ftv: sdio_wifi@1 {
|
||||
rtl8189ftv: wifi@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
@ -63,7 +63,7 @@
|
||||
* Explicitly define the sdio device, so that we can add an ethernet
|
||||
* alias for it (which e.g. makes u-boot set a mac-address).
|
||||
*/
|
||||
rtl8189ftv: sdio_wifi@1 {
|
||||
rtl8189ftv: wifi@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
@ -92,7 +92,7 @@
|
||||
regulator-max-microvolt = <3300000>;
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
|
||||
post-power-on-delay-ms = <200>;
|
||||
|
||||
@ -62,7 +62,7 @@
|
||||
};
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
/*
|
||||
* Q8 boards use various PL# pins as wifi-en. On other boards
|
||||
@ -94,7 +94,7 @@
|
||||
non-removable;
|
||||
status = "okay";
|
||||
|
||||
sdio_wifi: sdio_wifi@1 {
|
||||
sdio_wifi: wifi@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
@ -88,7 +88,7 @@
|
||||
regulator-max-microvolt = <5000000>;
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL06 */
|
||||
clocks = <&rtc CLK_OSC32K_FANOUT>;
|
||||
|
||||
@ -75,7 +75,7 @@
|
||||
};
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL06 */
|
||||
};
|
||||
|
||||
@ -100,7 +100,7 @@
|
||||
enable-active-high;
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */
|
||||
clocks = <&ccu CLK_OUTA>;
|
||||
|
||||
@ -62,7 +62,7 @@
|
||||
regulator-max-microvolt = <5000000>;
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&pio 1 10 GPIO_ACTIVE_LOW>; // PB10 WIFI_EN
|
||||
clocks = <&ccu CLK_OUTA>;
|
||||
|
||||
@ -51,7 +51,7 @@
|
||||
startup-delay-us = <200000>;
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&pio 1 3 GPIO_ACTIVE_LOW>; /* PB3 WIFI-RST */
|
||||
post-power-on-delay-ms = <200>;
|
||||
|
||||
@ -98,7 +98,7 @@
|
||||
#size-cells = <1>;
|
||||
ranges;
|
||||
|
||||
osc24M: osc24M_clk {
|
||||
osc24M: osc24M-clk {
|
||||
#clock-cells = <0>;
|
||||
compatible = "fixed-clock";
|
||||
clock-frequency = <24000000>;
|
||||
@ -106,7 +106,7 @@
|
||||
clock-output-names = "osc24M";
|
||||
};
|
||||
|
||||
osc32k: osc32k_clk {
|
||||
osc32k: osc32k-clk {
|
||||
#clock-cells = <0>;
|
||||
compatible = "fixed-clock";
|
||||
clock-frequency = <32768>;
|
||||
|
||||
@ -94,7 +94,7 @@
|
||||
enable-active-high;
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */
|
||||
clocks = <&ccu CLK_OUTA>;
|
||||
|
||||
@ -196,14 +196,14 @@
|
||||
* The actual TX clock rate is not controlled by the
|
||||
* gmac_tx clock.
|
||||
*/
|
||||
mii_phy_tx_clk: mii_phy_tx_clk {
|
||||
mii_phy_tx_clk: mii-phy-tx-clk {
|
||||
#clock-cells = <0>;
|
||||
compatible = "fixed-clock";
|
||||
clock-frequency = <25000000>;
|
||||
clock-output-names = "mii_phy_tx";
|
||||
};
|
||||
|
||||
gmac_int_tx_clk: gmac_int_tx_clk {
|
||||
gmac_int_tx_clk: gmac-int-tx-clk {
|
||||
#clock-cells = <0>;
|
||||
compatible = "fixed-clock";
|
||||
clock-frequency = <125000000>;
|
||||
|
||||
@ -98,7 +98,7 @@
|
||||
gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
|
||||
clocks = <&rtc CLK_OSC32K_FANOUT>;
|
||||
|
||||
@ -18,7 +18,7 @@
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
wifi_pwrseq: wifi_pwrseq {
|
||||
wifi_pwrseq: pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&pio 2 7 GPIO_ACTIVE_LOW>; /* PC7 */
|
||||
post-power-on-delay-ms = <200>;
|
||||
|
||||
@ -83,7 +83,7 @@
|
||||
#size-cells = <1>;
|
||||
ranges;
|
||||
|
||||
osc24M: osc24M_clk {
|
||||
osc24M: osc24M-clk {
|
||||
#clock-cells = <0>;
|
||||
compatible = "fixed-clock";
|
||||
clock-frequency = <24000000>;
|
||||
@ -91,7 +91,7 @@
|
||||
clock-output-names = "osc24M";
|
||||
};
|
||||
|
||||
osc32k: osc32k_clk {
|
||||
osc32k: osc32k-clk {
|
||||
#clock-cells = <0>;
|
||||
compatible = "fixed-clock";
|
||||
clock-frequency = <32768>;
|
||||
|
||||
@ -98,14 +98,14 @@
|
||||
|
||||
/* IPB PMIC */
|
||||
lm25066@40 {
|
||||
compatible = "lm25066";
|
||||
compatible = "ti,lm25066";
|
||||
reg = <0x40>;
|
||||
shunt-resistor-micro-ohms = <1000>;
|
||||
};
|
||||
|
||||
/* 12VSB PMIC */
|
||||
lm25066@41 {
|
||||
compatible = "lm25066";
|
||||
compatible = "ti,lm25066";
|
||||
reg = <0x41>;
|
||||
shunt-resistor-micro-ohms = <10000>;
|
||||
};
|
||||
|
||||
@ -14,7 +14,7 @@
|
||||
|
||||
#define EFUSE(hexaddr, num) \
|
||||
efuse@##hexaddr { \
|
||||
compatible = "lm25066"; \
|
||||
compatible = "ti,lm25066"; \
|
||||
reg = <0x##hexaddr>; \
|
||||
shunt-resistor-micro-ohms = <675>; \
|
||||
regulators { \
|
||||
|
||||
@ -64,6 +64,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
|
||||
bcm47081-luxul-xap-1410.dtb \
|
||||
bcm47081-luxul-xwr-1200.dtb \
|
||||
bcm47081-tplink-archer-c5-v2.dtb \
|
||||
bcm4709-asus-rt-ac3200.dtb \
|
||||
bcm4709-asus-rt-ac87u.dtb \
|
||||
bcm4709-buffalo-wxr-1900dhp.dtb \
|
||||
bcm4709-linksys-ea9200.dtb \
|
||||
@ -71,6 +72,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
|
||||
bcm4709-netgear-r8000.dtb \
|
||||
bcm4709-tplink-archer-c9-v1.dtb \
|
||||
bcm47094-asus-rt-ac3100.dtb \
|
||||
bcm47094-asus-rt-ac5300.dtb \
|
||||
bcm47094-asus-rt-ac88u.dtb \
|
||||
bcm47094-dlink-dir-885l.dtb \
|
||||
bcm47094-dlink-dir-890l.dtb \
|
||||
|
||||
@ -5,6 +5,7 @@
|
||||
#include "bcm283x-rpi-led-deprecated.dtsi"
|
||||
#include "bcm283x-rpi-usb-peripheral.dtsi"
|
||||
#include "bcm283x-rpi-wifi-bt.dtsi"
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
compatible = "raspberrypi,4-model-b", "brcm,bcm2711";
|
||||
@ -15,6 +16,13 @@
|
||||
stdout-path = "serial1:115200n8";
|
||||
};
|
||||
|
||||
cam1_reg: regulator-cam1 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "cam1-reg";
|
||||
enable-active-high;
|
||||
gpio = <&expgpio 5 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
sd_io_1v8_reg: regulator-sd-io-1v8 {
|
||||
compatible = "regulator-gpio";
|
||||
regulator-name = "vdd-sd-io";
|
||||
@ -197,6 +205,27 @@
|
||||
phy1: ethernet-phy@1 {
|
||||
/* No PHY interrupt */
|
||||
reg = <0x1>;
|
||||
|
||||
leds {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
/* LED1 */
|
||||
led@0 {
|
||||
reg = <0>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_LAN;
|
||||
default-state = "keep";
|
||||
};
|
||||
|
||||
/* LED2 */
|
||||
led@1 {
|
||||
reg = <1>;
|
||||
color = <LED_COLOR_ID_AMBER>;
|
||||
function = LED_FUNCTION_LAN;
|
||||
default-state = "keep";
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
@ -30,6 +30,7 @@
|
||||
|
||||
&genet_mdio {
|
||||
clock-frequency = <1950000>;
|
||||
/delete-node/ leds;
|
||||
};
|
||||
|
||||
&led_pwr {
|
||||
|
||||
@ -1,5 +1,6 @@
|
||||
// SPDX-License-Identifier: GPL-2.0
|
||||
/dts-v1/;
|
||||
#include <dt-bindings/leds/common.h>
|
||||
#include "bcm2711-rpi-cm4.dtsi"
|
||||
#include "bcm283x-rpi-led-deprecated.dtsi"
|
||||
#include "bcm283x-rpi-usb-host.dtsi"
|
||||
@ -101,6 +102,38 @@
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c0_1 {
|
||||
rtc@51 {
|
||||
/* Attention: An alarm resets the machine */
|
||||
compatible = "nxp,pcf85063a";
|
||||
reg = <0x51>;
|
||||
quartz-load-femtofarads = <7000>;
|
||||
};
|
||||
};
|
||||
|
||||
&phy1 {
|
||||
leds {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
/* LED2 */
|
||||
led@1 {
|
||||
reg = <1>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_LAN;
|
||||
default-state = "keep";
|
||||
};
|
||||
|
||||
/* LED3 */
|
||||
led@2 {
|
||||
reg = <2>;
|
||||
color = <LED_COLOR_ID_AMBER>;
|
||||
function = LED_FUNCTION_LAN;
|
||||
default-state = "keep";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&led_act {
|
||||
gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
@ -17,14 +17,33 @@
|
||||
pcie0 = &pcie0;
|
||||
blconfig = &blconfig;
|
||||
};
|
||||
|
||||
i2c0mux: i2c-mux0 {
|
||||
compatible = "i2c-mux-pinctrl";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
i2c-parent = <&i2c0>;
|
||||
|
||||
pinctrl-names = "i2c0", "i2c0-vc";
|
||||
pinctrl-0 = <&i2c0_gpio0>;
|
||||
pinctrl-1 = <&i2c0_gpio44>;
|
||||
|
||||
i2c0_0: i2c@0 {
|
||||
reg = <0>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
};
|
||||
|
||||
i2c0_1: i2c@1 {
|
||||
reg = <1>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&firmware {
|
||||
firmware_clocks: clocks {
|
||||
compatible = "raspberrypi,firmware-clocks";
|
||||
#clock-cells = <1>;
|
||||
};
|
||||
|
||||
expgpio: gpio {
|
||||
compatible = "raspberrypi,firmware-gpio";
|
||||
gpio-controller;
|
||||
@ -54,6 +73,11 @@
|
||||
clocks = <&firmware_clocks 4>;
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
/delete-property/ pinctrl-names;
|
||||
/delete-property/ pinctrl-0;
|
||||
};
|
||||
|
||||
&rmem {
|
||||
/*
|
||||
* RPi4's co-processor will copy the board's bootloader configuration
|
||||
|
||||
@ -432,8 +432,8 @@
|
||||
};
|
||||
};
|
||||
|
||||
arm-pmu {
|
||||
compatible = "arm,cortex-a72-pmu", "arm,armv8-pmuv3";
|
||||
pmu {
|
||||
compatible = "arm,cortex-a72-pmu";
|
||||
interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
|
||||
<GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
|
||||
@ -1114,6 +1114,14 @@
|
||||
#address-cells = <2>;
|
||||
};
|
||||
|
||||
&csi0 {
|
||||
interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
|
||||
&csi1 {
|
||||
interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
|
||||
&cma {
|
||||
/*
|
||||
* arm64 reserves the CMA by default somewhere in ZONE_DMA32,
|
||||
|
||||
@ -7,13 +7,6 @@
|
||||
|
||||
#include <dt-bindings/power/raspberrypi-power.h>
|
||||
|
||||
&firmware {
|
||||
firmware_clocks: clocks {
|
||||
compatible = "raspberrypi,firmware-clocks";
|
||||
#clock-cells = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&hdmi {
|
||||
clocks = <&firmware_clocks 9>,
|
||||
<&firmware_clocks 13>;
|
||||
|
||||
@ -4,11 +4,12 @@
|
||||
soc {
|
||||
firmware: firmware {
|
||||
compatible = "raspberrypi,bcm2835-firmware", "simple-mfd";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
mboxes = <&mailbox>;
|
||||
dma-ranges;
|
||||
|
||||
firmware_clocks: clocks {
|
||||
compatible = "raspberrypi,firmware-clocks";
|
||||
#clock-cells = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
power: power {
|
||||
@ -25,6 +26,20 @@
|
||||
};
|
||||
};
|
||||
|
||||
&csi0 {
|
||||
clocks = <&clocks BCM2835_CLOCK_CAM0>,
|
||||
<&firmware_clocks 4>;
|
||||
clock-names = "lp", "vpu";
|
||||
power-domains = <&power RPI_POWER_DOMAIN_UNICAM0>;
|
||||
};
|
||||
|
||||
&csi1 {
|
||||
clocks = <&clocks BCM2835_CLOCK_CAM1>,
|
||||
<&firmware_clocks 4>;
|
||||
clock-names = "lp", "vpu";
|
||||
power-domains = <&power RPI_POWER_DOMAIN_UNICAM1>;
|
||||
};
|
||||
|
||||
&gpio {
|
||||
gpioout: gpioout {
|
||||
brcm,pins = <6>;
|
||||
|
||||
@ -454,6 +454,30 @@
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
csi0: csi@7e800000 {
|
||||
compatible = "brcm,bcm2835-unicam";
|
||||
reg = <0x7e800000 0x800>,
|
||||
<0x7e802000 0x4>;
|
||||
reg-names = "unicam", "cmi";
|
||||
interrupts = <2 6>;
|
||||
brcm,num-data-lanes = <2>;
|
||||
status = "disabled";
|
||||
port {
|
||||
};
|
||||
};
|
||||
|
||||
csi1: csi@7e801000 {
|
||||
compatible = "brcm,bcm2835-unicam";
|
||||
reg = <0x7e801000 0x800>,
|
||||
<0x7e802004 0x4>;
|
||||
reg-names = "unicam", "cmi";
|
||||
interrupts = <2 7>;
|
||||
brcm,num-data-lanes = <4>;
|
||||
status = "disabled";
|
||||
port {
|
||||
};
|
||||
};
|
||||
|
||||
i2c1: i2c@7e804000 {
|
||||
compatible = "brcm,bcm2835-i2c";
|
||||
reg = <0x7e804000 0x1000>;
|
||||
|
||||
150
arch/arm/boot/dts/broadcom/bcm4709-asus-rt-ac3200.dts
Normal file
150
arch/arm/boot/dts/broadcom/bcm4709-asus-rt-ac3200.dts
Normal file
@ -0,0 +1,150 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/*
|
||||
* Author: Tom Brautaset <tbrautaset@gmail.com>
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "bcm4709.dtsi"
|
||||
#include "bcm5301x-nand-cs0-bch8.dtsi"
|
||||
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
compatible = "asus,rt-ac3200", "brcm,bcm4709", "brcm,bcm4708";
|
||||
model = "ASUS RT-AC3200";
|
||||
|
||||
memory@0 {
|
||||
reg = <0x00000000 0x08000000>,
|
||||
<0x88000000 0x08000000>;
|
||||
device_type = "memory";
|
||||
};
|
||||
|
||||
nvram@1c080000 {
|
||||
compatible = "brcm,nvram";
|
||||
reg = <0x1c080000 0x00180000>;
|
||||
|
||||
et0macaddr: et0macaddr {
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
button-reset {
|
||||
label = "Reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
button-wifi {
|
||||
label = "Wi-Fi";
|
||||
linux,code = <KEY_RFKILL>;
|
||||
gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
button-wps {
|
||||
label = "WPS";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led-power {
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "default-on";
|
||||
};
|
||||
|
||||
led-wan-red {
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_WAN;
|
||||
gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led-wps {
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
function = LED_FUNCTION_WPS;
|
||||
gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
nvmem-cells = <&et0macaddr 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
nvmem-cells = <&et0macaddr 1>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&gmac2 {
|
||||
nvmem-cells = <&et0macaddr 2>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&nandcs {
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
reg = <0x00000000 0x00080000>;
|
||||
label = "boot";
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
reg = <0x00080000 0x00180000>;
|
||||
label = "nvram";
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
compatible = "brcm,trx";
|
||||
reg = <0x00200000 0x07e00000>;
|
||||
label = "firmware";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&srab {
|
||||
status = "okay";
|
||||
|
||||
ports {
|
||||
port@0 {
|
||||
label = "wan";
|
||||
};
|
||||
|
||||
port@1 {
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
port@3 {
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
port@4 {
|
||||
label = "lan4";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb2 {
|
||||
vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
&usb3_phy {
|
||||
status = "okay";
|
||||
};
|
||||
@ -13,11 +13,22 @@
|
||||
|
||||
nvram@1c080000 {
|
||||
et0macaddr: et0macaddr {
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
nvmem-cells = <&et0macaddr>;
|
||||
nvmem-cells = <&et0macaddr 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
nvmem-cells = <&et0macaddr 1>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&gmac2 {
|
||||
nvmem-cells = <&et0macaddr 2>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
@ -6,15 +6,13 @@
|
||||
#include "bcm47094.dtsi"
|
||||
#include "bcm5301x-nand-cs0-bch8.dtsi"
|
||||
|
||||
/ {
|
||||
chosen {
|
||||
bootargs = "earlycon";
|
||||
};
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
memory@0 {
|
||||
device_type = "memory";
|
||||
reg = <0x00000000 0x08000000>,
|
||||
<0x88000000 0x18000000>;
|
||||
device_type = "memory";
|
||||
};
|
||||
|
||||
nvram@1c080000 {
|
||||
@ -22,52 +20,13 @@
|
||||
reg = <0x1c080000 0x00180000>;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led-power {
|
||||
label = "white:power";
|
||||
gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "default-on";
|
||||
};
|
||||
|
||||
led-wan-red {
|
||||
label = "red:wan";
|
||||
gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led-lan {
|
||||
label = "white:lan";
|
||||
gpios = <&chipcommon 21 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-usb2 {
|
||||
label = "white:usb2";
|
||||
gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
|
||||
trigger-sources = <&ehci_port2>;
|
||||
linux,default-trigger = "usbport";
|
||||
};
|
||||
|
||||
led-usb3 {
|
||||
label = "white:usb3";
|
||||
gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
|
||||
trigger-sources = <&ehci_port1>, <&xhci_port1>;
|
||||
linux,default-trigger = "usbport";
|
||||
};
|
||||
|
||||
led-wps {
|
||||
label = "white:wps";
|
||||
gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
button-wps {
|
||||
label = "WPS";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
|
||||
button-led {
|
||||
label = "Backlight";
|
||||
linux,code = <KEY_BRIGHTNESS_ZERO>;
|
||||
gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
button-reset {
|
||||
@ -82,16 +41,87 @@
|
||||
gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
button-led {
|
||||
label = "Backlight";
|
||||
linux,code = <KEY_BRIGHTNESS_ZERO>;
|
||||
gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
|
||||
button-wps {
|
||||
label = "WPS";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led-lan {
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
function = LED_FUNCTION_LAN;
|
||||
gpios = <&chipcommon 21 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-power {
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "default-on";
|
||||
};
|
||||
|
||||
led-usb2 {
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
function = LED_FUNCTION_USB;
|
||||
function-enumerator = <1>;
|
||||
gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
|
||||
trigger-sources = <&ehci_port2>;
|
||||
linux,default-trigger = "usbport";
|
||||
};
|
||||
|
||||
led-usb3 {
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
function = LED_FUNCTION_USB;
|
||||
function-enumerator = <2>;
|
||||
gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
|
||||
trigger-sources = <&ehci_port1>, <&xhci_port1>;
|
||||
linux,default-trigger = "usbport";
|
||||
};
|
||||
|
||||
led-wan-red {
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_WAN;
|
||||
gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led-wps {
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
function = LED_FUNCTION_WPS;
|
||||
gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nandcs {
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
reg = <0x00000000 0x00080000>;
|
||||
label = "boot";
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
reg = <0x00080000 0x00180000>;
|
||||
label = "nvram";
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
compatible = "brcm,trx";
|
||||
reg = <0x00200000 0x07e00000>;
|
||||
label = "firmware";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&srab {
|
||||
compatible = "brcm,bcm53012-srab", "brcm,bcm5301x-srab";
|
||||
status = "okay";
|
||||
|
||||
ports {
|
||||
@ -136,28 +166,3 @@
|
||||
&usb3_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&nandcs {
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "boot";
|
||||
reg = <0x00000000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "nvram";
|
||||
reg = <0x00080000 0x00180000>;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "firmware";
|
||||
reg = <0x00200000 0x07e00000>;
|
||||
compatible = "brcm,trx";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
156
arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac5300.dts
Normal file
156
arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac5300.dts
Normal file
@ -0,0 +1,156 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/*
|
||||
* Author: Tom Brautaset <tbrautaset@gmail.com>
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "bcm47094.dtsi"
|
||||
#include "bcm5301x-nand-cs0-bch8.dtsi"
|
||||
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
compatible = "asus,rt-ac5300", "brcm,bcm47094", "brcm,bcm4708";
|
||||
model = "ASUS RT-AC5300";
|
||||
|
||||
memory@0 {
|
||||
reg = <0x00000000 0x08000000>,
|
||||
<0x88000000 0x18000000>;
|
||||
device_type = "memory";
|
||||
};
|
||||
|
||||
nvram@1c080000 {
|
||||
compatible = "brcm,nvram";
|
||||
reg = <0x1c080000 0x00180000>;
|
||||
|
||||
et1macaddr: et1macaddr {
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
button-reset {
|
||||
label = "Reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
button-wifi {
|
||||
label = "Wi-Fi";
|
||||
linux,code = <KEY_RFKILL>;
|
||||
gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
button-wps {
|
||||
label = "WPS";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led-lan {
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
function = LED_FUNCTION_LAN;
|
||||
gpios = <&chipcommon 21 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-power {
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "default-on";
|
||||
};
|
||||
|
||||
led-wan-red {
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_WAN;
|
||||
gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led-wps {
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
function = LED_FUNCTION_WPS;
|
||||
gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
nvmem-cells = <&et1macaddr 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
nvmem-cells = <&et1macaddr 1>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&gmac2 {
|
||||
nvmem-cells = <&et1macaddr 2>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&nandcs {
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
reg = <0x00000000 0x00080000>;
|
||||
label = "boot";
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
reg = <0x00080000 0x00180000>;
|
||||
label = "nvram";
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
compatible = "brcm,trx";
|
||||
reg = <0x00200000 0x07e00000>;
|
||||
label = "firmware";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&srab {
|
||||
status = "okay";
|
||||
|
||||
ports {
|
||||
port@0 {
|
||||
label = "lan4";
|
||||
};
|
||||
|
||||
port@1 {
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
port@3 {
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
port@4 {
|
||||
label = "wan";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb2 {
|
||||
vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
&usb3_phy {
|
||||
status = "okay";
|
||||
};
|
||||
@ -13,18 +13,40 @@
|
||||
|
||||
nvram@1c080000 {
|
||||
et1macaddr: et1macaddr {
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
switch {
|
||||
compatible = "realtek,rtl8365mb";
|
||||
/* 7 = MDIO (has input reads), 6 = MDC (clock, output only) */
|
||||
mdc-gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
|
||||
mdio-gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
|
||||
reset-gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
|
||||
realtek,disable-leds;
|
||||
dsa,member = <1 0>;
|
||||
|
||||
mdio {
|
||||
compatible = "realtek,smi-mdio";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
ethphy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
};
|
||||
|
||||
ethphy1: ethernet-phy@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
|
||||
ethphy2: ethernet-phy@2 {
|
||||
reg = <2>;
|
||||
};
|
||||
|
||||
ethphy3: ethernet-phy@3 {
|
||||
reg = <3>;
|
||||
};
|
||||
};
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
@ -68,31 +90,23 @@
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
mdio {
|
||||
compatible = "realtek,smi-mdio";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
ethphy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
};
|
||||
|
||||
ethphy1: ethernet-phy@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
|
||||
ethphy2: ethernet-phy@2 {
|
||||
reg = <2>;
|
||||
};
|
||||
|
||||
ethphy3: ethernet-phy@3 {
|
||||
reg = <3>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
nvmem-cells = <&et1macaddr 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&gmac2 {
|
||||
nvmem-cells = <&et1macaddr 1>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&srab {
|
||||
dsa,member = <0 0>;
|
||||
|
||||
@ -111,12 +125,3 @@
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
nvmem-cells = <&et1macaddr>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
@ -445,9 +445,9 @@
|
||||
|
||||
tegra_ac97: ac97@70002000 {
|
||||
status = "okay";
|
||||
nvidia,codec-reset-gpio =
|
||||
nvidia,codec-reset-gpios =
|
||||
<&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
|
||||
nvidia,codec-sync-gpio =
|
||||
nvidia,codec-sync-gpios =
|
||||
<&gpio TEGRA_GPIO(P, 0) GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
|
||||
@ -533,6 +533,49 @@
|
||||
0x00000000 0x00000000 0x00000000 0x00000000>;
|
||||
};
|
||||
};
|
||||
|
||||
emc-tables@1 {
|
||||
nvidia,ram-code = <0x1>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <1>;
|
||||
|
||||
emc-table@166500 {
|
||||
reg = <166500>;
|
||||
compatible = "nvidia,tegra20-emc-table";
|
||||
clock-frequency = <166500>;
|
||||
nvidia,emc-registers = <0x0000000a 0x00000016
|
||||
0x00000008 0x00000003 0x00000004 0x00000004
|
||||
0x00000002 0x0000000c 0x00000003 0x00000003
|
||||
0x00000002 0x00000001 0x00000004 0x00000005
|
||||
0x00000004 0x00000009 0x0000000d 0x000004df
|
||||
0x00000000 0x00000003 0x00000003 0x00000003
|
||||
0x00000003 0x00000001 0x0000000a 0x000000c8
|
||||
0x00000003 0x00000006 0x00000004 0x00000008
|
||||
0x00000002 0x00000000 0x00000000 0x00000002
|
||||
0x00000000 0x00000000 0x00000083 0xe03b0323
|
||||
0x007fe010 0x00001414 0x00000000 0x00000000
|
||||
0x00000000 0x00000000 0x00000000 0x00000000>;
|
||||
};
|
||||
|
||||
emc-table@333000 {
|
||||
reg = <333000>;
|
||||
compatible = "nvidia,tegra20-emc-table";
|
||||
clock-frequency = <333000>;
|
||||
nvidia,emc-registers = <0x00000018 0x00000033
|
||||
0x00000012 0x00000004 0x00000004 0x00000005
|
||||
0x00000003 0x0000000c 0x00000006 0x00000006
|
||||
0x00000003 0x00000001 0x00000004 0x00000005
|
||||
0x00000004 0x00000009 0x0000000d 0x00000bff
|
||||
0x00000000 0x00000003 0x00000003 0x00000006
|
||||
0x00000006 0x00000001 0x00000011 0x000000c8
|
||||
0x00000003 0x0000000e 0x00000007 0x00000008
|
||||
0x00000002 0x00000000 0x00000000 0x00000002
|
||||
0x00000000 0x00000000 0x00000083 0xf0440303
|
||||
0x007fe010 0x00001414 0x00000000 0x00000000
|
||||
0x00000000 0x00000000 0x00000000 0x00000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
usb@c5000000 {
|
||||
|
||||
@ -349,12 +349,15 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
|
||||
imx6ull-phytec-segin-lc-rdk-nand.dtb \
|
||||
imx6ull-phytec-tauri-emmc.dtb \
|
||||
imx6ull-phytec-tauri-nand.dtb \
|
||||
imx6ull-seeed-npi-dev-board-emmc.dtb \
|
||||
imx6ull-seeed-npi-dev-board-nand.dtb \
|
||||
imx6ull-tarragon-master.dtb \
|
||||
imx6ull-tarragon-micro.dtb \
|
||||
imx6ull-tarragon-slave.dtb \
|
||||
imx6ull-tarragon-slavext.dtb \
|
||||
imx6ull-tqma6ull2-mba6ulx.dtb \
|
||||
imx6ull-tqma6ull2l-mba6ulx.dtb \
|
||||
imx6ull-uti260b.dtb \
|
||||
imx6ulz-14x14-evk.dtb \
|
||||
imx6ulz-bsh-smm-m2.dtb
|
||||
dtb-$(CONFIG_SOC_IMX7D) += \
|
||||
|
||||
@ -127,7 +127,7 @@
|
||||
compatible = "ricoh,rc5t619";
|
||||
reg = <0x32>;
|
||||
interrupt-parent = <&gpio5>;
|
||||
interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
|
||||
interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
|
||||
system-power-controller;
|
||||
|
||||
regulators {
|
||||
|
||||
@ -145,7 +145,7 @@
|
||||
compatible = "ricoh,rc5t619";
|
||||
reg = <0x32>;
|
||||
interrupt-parent = <&gpio4>;
|
||||
interrupts = <19 IRQ_TYPE_EDGE_FALLING>;
|
||||
interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
|
||||
system-power-controller;
|
||||
|
||||
regulators {
|
||||
|
||||
@ -15,6 +15,22 @@
|
||||
device_type = "memory";
|
||||
reg = <0xa0000000 0x08000000>; /* 128MB */
|
||||
};
|
||||
|
||||
usbotgphy: usbotgphy {
|
||||
compatible = "usb-nop-xceiv";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usbotgphy>;
|
||||
reset-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>;
|
||||
#phy-cells = <0>;
|
||||
};
|
||||
|
||||
usbh2phy: usbh2phy {
|
||||
compatible = "usb-nop-xceiv";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usbh2phy>;
|
||||
reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;
|
||||
#phy-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&cspi1 {
|
||||
@ -84,6 +100,52 @@
|
||||
MX27_PAD_NFWE_B__NFWE_B 0x0
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_usbotgphy: usbotgphygrp {
|
||||
fsl,pins = <
|
||||
MX27_PAD_USBH1_RCV__GPIO2_25 0x1 /* reset gpio */
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_usbotg: usbotggrp {
|
||||
fsl,pins = <
|
||||
MX27_PAD_USBOTG_CLK__USBOTG_CLK 0x0
|
||||
MX27_PAD_USBOTG_DIR__USBOTG_DIR 0x0
|
||||
MX27_PAD_USBOTG_NXT__USBOTG_NXT 0x0
|
||||
MX27_PAD_USBOTG_STP__USBOTG_STP 0x0
|
||||
MX27_PAD_USBOTG_DATA0__USBOTG_DATA0 0x0
|
||||
MX27_PAD_USBOTG_DATA1__USBOTG_DATA1 0x0
|
||||
MX27_PAD_USBOTG_DATA2__USBOTG_DATA2 0x0
|
||||
MX27_PAD_USBOTG_DATA3__USBOTG_DATA3 0x0
|
||||
MX27_PAD_USBOTG_DATA4__USBOTG_DATA4 0x0
|
||||
MX27_PAD_USBOTG_DATA5__USBOTG_DATA5 0x0
|
||||
MX27_PAD_USBOTG_DATA6__USBOTG_DATA6 0x0
|
||||
MX27_PAD_USBOTG_DATA7__USBOTG_DATA7 0x0
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_usbh2phy: usbh2phygrp {
|
||||
fsl,pins = <
|
||||
MX27_PAD_USBH1_SUSP__GPIO2_22 0x0 /* reset gpio */
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_usbh2: usbh2grp {
|
||||
fsl,pins = <
|
||||
MX27_PAD_USBH2_CLK__USBH2_CLK 0x0
|
||||
MX27_PAD_USBH2_DIR__USBH2_DIR 0x0
|
||||
MX27_PAD_USBH2_NXT__USBH2_NXT 0x0
|
||||
MX27_PAD_USBH2_STP__USBH2_STP 0x0
|
||||
MX27_PAD_CSPI2_SCLK__USBH2_DATA0 0x0
|
||||
MX27_PAD_CSPI2_MOSI__USBH2_DATA1 0x0
|
||||
MX27_PAD_CSPI2_MISO__USBH2_DATA2 0x0
|
||||
MX27_PAD_CSPI2_SS1__USBH2_DATA3 0x0
|
||||
MX27_PAD_CSPI2_SS2__USBH2_DATA4 0x0
|
||||
MX27_PAD_CSPI1_SS2__USBH2_DATA5 0x0
|
||||
MX27_PAD_CSPI2_SS0__USBH2_DATA6 0x0
|
||||
MX27_PAD_USBH2_DATA7__USBH2_DATA7 0x0
|
||||
>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
@ -95,3 +157,19 @@
|
||||
nand-on-flash-bbt;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbotg {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usbotg>;
|
||||
phy_type = "ulpi";
|
||||
phys = <&usbotgphy>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbh2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usbh2>;
|
||||
phy_type = "ulpi";
|
||||
phys = <&usbh2phy>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
@ -45,7 +45,7 @@
|
||||
|
||||
backlight: backlight {
|
||||
compatible = "pwm-backlight";
|
||||
pwms = <&pwm1 0 78770>;
|
||||
pwms = <&pwm1 0 78770 0>;
|
||||
brightness-levels = <0 150 200 255>;
|
||||
default-brightness-level = <1>;
|
||||
power-supply = <&backlight_reg>;
|
||||
@ -113,7 +113,6 @@
|
||||
};
|
||||
|
||||
&pwm1 {
|
||||
#pwm-cells = <2>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_pwm_backlight>;
|
||||
status = "okay";
|
||||
|
||||
@ -13,7 +13,7 @@
|
||||
|
||||
backlight_lcd: backlight {
|
||||
compatible = "pwm-backlight";
|
||||
pwms = <&pwm2 0 50000>;
|
||||
pwms = <&pwm2 0 50000 0>;
|
||||
power-supply = <®_backlight>;
|
||||
brightness-levels = <0 24 28 32 36
|
||||
40 44 48 52 56
|
||||
|
||||
@ -13,7 +13,7 @@
|
||||
compatible = "pwm-beeper";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_buzzer>;
|
||||
pwms = <&pwm1 0 500000>;
|
||||
pwms = <&pwm1 0 500000 0>;
|
||||
};
|
||||
|
||||
gpio-buttons {
|
||||
@ -162,14 +162,6 @@
|
||||
>;
|
||||
};
|
||||
|
||||
&pwm1 {
|
||||
#pwm-cells = <2>;
|
||||
};
|
||||
|
||||
&pwm2 {
|
||||
#pwm-cells = <2>;
|
||||
};
|
||||
|
||||
&uart1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
@ -41,7 +41,7 @@
|
||||
|
||||
backlight {
|
||||
compatible = "pwm-backlight";
|
||||
pwms = <&pwm1 0 3000>;
|
||||
pwms = <&pwm1 0 3000 0>;
|
||||
brightness-levels = <0 4 8 16 32 64 128 255>;
|
||||
default-brightness-level = <6>;
|
||||
power-supply = <®_backlight>;
|
||||
@ -313,7 +313,6 @@
|
||||
};
|
||||
|
||||
&pwm1 {
|
||||
#pwm-cells = <2>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_pwm1>;
|
||||
status = "okay";
|
||||
|
||||
@ -17,7 +17,7 @@
|
||||
|
||||
backlight {
|
||||
compatible = "pwm-backlight";
|
||||
pwms = <&pwm2 0 50000>;
|
||||
pwms = <&pwm2 0 50000 0>;
|
||||
brightness-levels = <0 24 28 32 36 40 44 48 52 56 60 64 68 72 76 80 84 88 92 96 100>;
|
||||
default-brightness-level = <10>;
|
||||
enable-gpios = <&gpio7 7 0>;
|
||||
|
||||
@ -167,7 +167,7 @@
|
||||
|
||||
pwm_bl: backlight {
|
||||
compatible = "pwm-backlight";
|
||||
pwms = <&pwm2 0 50000>;
|
||||
pwms = <&pwm2 0 50000 0>;
|
||||
brightness-levels = <0 2 5 7 10 12 15 17 20 22 25 28 30 33 35
|
||||
38 40 43 45 48 51 53 56 58 61 63 66 68 71
|
||||
73 76 79 81 84 86 89 91 94 96 99 102 104
|
||||
@ -187,7 +187,7 @@
|
||||
|
||||
led-1 {
|
||||
label = "alarm-brightness";
|
||||
pwms = <&pwm1 0 100000>;
|
||||
pwms = <&pwm1 0 100000 0>;
|
||||
max-brightness = <255>;
|
||||
};
|
||||
};
|
||||
@ -628,14 +628,12 @@
|
||||
};
|
||||
|
||||
&pwm1 {
|
||||
#pwm-cells = <2>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_pwm1>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pwm2 {
|
||||
#pwm-cells = <2>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_pwm2>;
|
||||
status = "okay";
|
||||
|
||||
@ -202,14 +202,6 @@
|
||||
};
|
||||
};
|
||||
|
||||
&pwm1 {
|
||||
#pwm-cells = <2>;
|
||||
};
|
||||
|
||||
&pwm2 {
|
||||
#pwm-cells = <2>;
|
||||
};
|
||||
|
||||
&uart1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_uart1>;
|
||||
|
||||
@ -14,7 +14,7 @@
|
||||
|
||||
backlight {
|
||||
compatible = "pwm-backlight";
|
||||
pwms = <&pwm1 0 5000000>;
|
||||
pwms = <&pwm1 0 5000000 0>;
|
||||
brightness-levels = <0 4 8 16 32 64 128 255>;
|
||||
default-brightness-level = <7>;
|
||||
enable-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
|
||||
@ -79,6 +79,5 @@
|
||||
};
|
||||
|
||||
&pwm1 {
|
||||
#pwm-cells = <2>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
@ -49,7 +49,7 @@
|
||||
|
||||
backlight {
|
||||
compatible = "pwm-backlight";
|
||||
pwms = <&pwm3 0 3000>;
|
||||
pwms = <&pwm3 0 3000 0>;
|
||||
brightness-levels = <0 4 8 16 32 64 128 255>;
|
||||
default-brightness-level = <6>;
|
||||
pinctrl-names = "default";
|
||||
@ -69,6 +69,5 @@
|
||||
};
|
||||
|
||||
&pwm3 {
|
||||
#pwm-cells = <2>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
Some files were not shown because too many files have changed in this diff Show More
Loading…
Reference in New Issue
Block a user