cpufreq: powerpc/platforms/cell: move cpufreq driver to drivers/cpufreq

This patch moves cpufreq driver of powerpc platforms/cell to drivers/cpufreq.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

arch/powerpc/platforms/cell/Kconfig

@@ -113,34 +113,10 @@ config CBE_THERM
 	default m
 	depends on CBE_RAS && SPU_BASE
 
-config CBE_CPUFREQ
-	tristate "CBE frequency scaling"
-	depends on CBE_RAS && CPU_FREQ
-	default m
-	help
-	  This adds the cpufreq driver for Cell BE processors.
-	  For details, take a look at <file:Documentation/cpu-freq/>.
-	  If you don't have such processor, say N
-
-config CBE_CPUFREQ_PMI_ENABLE
-	bool "CBE frequency scaling using PMI interface"
-	depends on CBE_CPUFREQ
-	default n
-	help
-	  Select this, if you want to use the PMI interface
-	  to switch frequencies. Using PMI, the
-	  processor will not only be able to run at lower speed,
-	  but also at lower core voltage.
-
-config CBE_CPUFREQ_PMI
-	tristate
-	depends on CBE_CPUFREQ_PMI_ENABLE
-	default CBE_CPUFREQ
-
 config PPC_PMI
 	tristate
 	default y
-	depends on CBE_CPUFREQ_PMI || PPC_IBM_CELL_POWERBUTTON
+	depends on CPU_FREQ_CBE_PMI || PPC_IBM_CELL_POWERBUTTON
 	help
 	  PMI (Platform Management Interrupt) is a way to
 	  communicate with the BMC (Baseboard Management Controller).

arch/powerpc/platforms/cell/Makefile

@@ -5,9 +5,6 @@ obj-$(CONFIG_PPC_CELL_NATIVE)		+= iommu.o setup.o spider-pic.o \
 obj-$(CONFIG_CBE_RAS)			+= ras.o
 
 obj-$(CONFIG_CBE_THERM)			+= cbe_thermal.o
-obj-$(CONFIG_CBE_CPUFREQ_PMI)		+= cbe_cpufreq_pmi.o
-obj-$(CONFIG_CBE_CPUFREQ)		+= cbe-cpufreq.o
-cbe-cpufreq-y				+= cbe_cpufreq_pervasive.o cbe_cpufreq.o
 obj-$(CONFIG_CBE_CPUFREQ_SPU_GOVERNOR)	+= cpufreq_spudemand.o
 
 obj-$(CONFIG_PPC_IBM_CELL_POWERBUTTON)	+= cbe_powerbutton.o

drivers/cpufreq/Kconfig.powerpc

@@ -1,3 +1,21 @@
+config CPU_FREQ_CBE
+	tristate "CBE frequency scaling"
+	depends on CBE_RAS && PPC_CELL
+	default m
+	help
+	  This adds the cpufreq driver for Cell BE processors.
+	  For details, take a look at <file:Documentation/cpu-freq/>.
+	  If you don't have such processor, say N
+
+config CPU_FREQ_CBE_PMI
+	bool "CBE frequency scaling using PMI interface"
+	depends on CPU_FREQ_CBE
+	default n
+	help
+	  Select this, if you want to use the PMI interface to switch
+	  frequencies. Using PMI, the processor will not only be able to run at
+	  lower speed, but also at lower core voltage.
+
 config CPU_FREQ_MAPLE
 	bool "Support for Maple 970FX Evaluation Board"
 	depends on PPC_MAPLE

drivers/cpufreq/Makefile

@@ -73,6 +73,9 @@ obj-$(CONFIG_ARCH_TEGRA)		+= tegra-cpufreq.o
 
 ##################################################################################
 # PowerPC platform drivers
+obj-$(CONFIG_CPU_FREQ_CBE)		+= ppc-cbe-cpufreq.o
+ppc-cbe-cpufreq-y			+= ppc_cbe_cpufreq_pervasive.o ppc_cbe_cpufreq.o
+obj-$(CONFIG_CPU_FREQ_CBE_PMI)		+= ppc_cbe_cpufreq_pmi.o
 obj-$(CONFIG_CPU_FREQ_MAPLE)		+= maple-cpufreq.o
 
 ##################################################################################

drivers/cpufreq/ppc_cbe_cpufreq.c

@@ -27,7 +27,8 @@
 #include <asm/machdep.h>
 #include <asm/prom.h>
 #include <asm/cell-regs.h>
-#include "cbe_cpufreq.h"
+
+#include "ppc_cbe_cpufreq.h"
 
 static DEFINE_MUTEX(cbe_switch_mutex);
 

drivers/cpufreq/ppc_cbe_cpufreq.h

@@ -1,5 +1,5 @@
 /*
- * cbe_cpufreq.h
+ * ppc_cbe_cpufreq.h
  *
  * This file contains the definitions used by the cbe_cpufreq driver.
  *
@@ -17,7 +17,7 @@ int cbe_cpufreq_get_pmode(int cpu);
 
 int cbe_cpufreq_set_pmode_pmi(int cpu, unsigned int pmode);
 
-#if defined(CONFIG_CBE_CPUFREQ_PMI) || defined(CONFIG_CBE_CPUFREQ_PMI_MODULE)
+#if defined(CONFIG_CPU_FREQ_CBE_PMI) || defined(CONFIG_CPU_FREQ_CBE_PMI_MODULE)
 extern bool cbe_cpufreq_has_pmi;
 #else
 #define cbe_cpufreq_has_pmi (0)

drivers/cpufreq/ppc_cbe_cpufreq_pervasive.c

@@ -30,7 +30,7 @@
 #include <asm/hw_irq.h>
 #include <asm/cell-regs.h>
 
-#include "cbe_cpufreq.h"
+#include "ppc_cbe_cpufreq.h"
 
 /* to write to MIC register */
 static u64 MIC_Slow_Fast_Timer_table[] = {

drivers/cpufreq/ppc_cbe_cpufreq_pmi.c

@@ -35,7 +35,7 @@
 #include <asm/time.h>
 #endif
 
-#include "cbe_cpufreq.h"
+#include "ppc_cbe_cpufreq.h"
 
 static u8 pmi_slow_mode_limit[MAX_CBE];