diff --git a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_ethtool.c b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_ethtool.c index 26eb00a45db1..03f593e84c24 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_ethtool.c +++ b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_ethtool.c @@ -801,6 +801,104 @@ static int set_link_ksettings(struct net_device *dev, return ret; } +/* Translate the Firmware FEC value into the ethtool value. */ +static inline unsigned int fwcap_to_eth_fec(unsigned int fw_fec) +{ + unsigned int eth_fec = 0; + + if (fw_fec & FW_PORT_CAP_FEC_RS) + eth_fec |= ETHTOOL_FEC_RS; + if (fw_fec & FW_PORT_CAP_FEC_BASER_RS) + eth_fec |= ETHTOOL_FEC_BASER; + + /* if nothing is set, then FEC is off */ + if (!eth_fec) + eth_fec = ETHTOOL_FEC_OFF; + + return eth_fec; +} + +/* Translate Common Code FEC value into ethtool value. */ +static inline unsigned int cc_to_eth_fec(unsigned int cc_fec) +{ + unsigned int eth_fec = 0; + + if (cc_fec & FEC_AUTO) + eth_fec |= ETHTOOL_FEC_AUTO; + if (cc_fec & FEC_RS) + eth_fec |= ETHTOOL_FEC_RS; + if (cc_fec & FEC_BASER_RS) + eth_fec |= ETHTOOL_FEC_BASER; + + /* if nothing is set, then FEC is off */ + if (!eth_fec) + eth_fec = ETHTOOL_FEC_OFF; + + return eth_fec; +} + +/* Translate ethtool FEC value into Common Code value. */ +static inline unsigned int eth_to_cc_fec(unsigned int eth_fec) +{ + unsigned int cc_fec = 0; + + if (eth_fec & ETHTOOL_FEC_OFF) + return cc_fec; + + if (eth_fec & ETHTOOL_FEC_AUTO) + cc_fec |= FEC_AUTO; + if (eth_fec & ETHTOOL_FEC_RS) + cc_fec |= FEC_RS; + if (eth_fec & ETHTOOL_FEC_BASER) + cc_fec |= FEC_BASER_RS; + + return cc_fec; +} + +static int get_fecparam(struct net_device *dev, struct ethtool_fecparam *fec) +{ + const struct port_info *pi = netdev_priv(dev); + const struct link_config *lc = &pi->link_cfg; + + /* Translate the Firmware FEC Support into the ethtool value. We + * always support IEEE 802.3 "automatic" selection of Link FEC type if + * any FEC is supported. + */ + fec->fec = fwcap_to_eth_fec(lc->supported); + if (fec->fec != ETHTOOL_FEC_OFF) + fec->fec |= ETHTOOL_FEC_AUTO; + + /* Translate the current internal FEC parameters into the + * ethtool values. + */ + fec->active_fec = cc_to_eth_fec(lc->fec); + + return 0; +} + +static int set_fecparam(struct net_device *dev, struct ethtool_fecparam *fec) +{ + struct port_info *pi = netdev_priv(dev); + struct link_config *lc = &pi->link_cfg; + struct link_config old_lc; + int ret; + + /* Save old Link Configuration in case the L1 Configure below + * fails. + */ + old_lc = *lc; + + /* Try to perform the L1 Configure and return the result of that + * effort. If it fails, revert the attempted change. + */ + lc->requested_fec = eth_to_cc_fec(fec->fec); + ret = t4_link_l1cfg(pi->adapter, pi->adapter->mbox, + pi->tx_chan, lc); + if (ret) + *lc = old_lc; + return ret; +} + static void get_pauseparam(struct net_device *dev, struct ethtool_pauseparam *epause) { @@ -1255,6 +1353,8 @@ static int get_rxnfc(struct net_device *dev, struct ethtool_rxnfc *info, static const struct ethtool_ops cxgb_ethtool_ops = { .get_link_ksettings = get_link_ksettings, .set_link_ksettings = set_link_ksettings, + .get_fecparam = get_fecparam, + .set_fecparam = set_fecparam, .get_drvinfo = get_drvinfo, .get_msglevel = get_msglevel, .set_msglevel = set_msglevel, diff --git a/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c b/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c index db41b3e99b81..24087c886974 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c +++ b/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c @@ -3840,11 +3840,64 @@ void t4_ulprx_read_la(struct adapter *adap, u32 *la_buf) FW_PORT_CAP_SPEED_40G | FW_PORT_CAP_SPEED_100G | \ FW_PORT_CAP_ANEG) +/* Translate Firmware Port Capabilities Pause specification to Common Code */ +static inline unsigned int fwcap_to_cc_pause(unsigned int fw_pause) +{ + unsigned int cc_pause = 0; + + if (fw_pause & FW_PORT_CAP_FC_RX) + cc_pause |= PAUSE_RX; + if (fw_pause & FW_PORT_CAP_FC_TX) + cc_pause |= PAUSE_TX; + + return cc_pause; +} + +/* Translate Common Code Pause specification into Firmware Port Capabilities */ +static inline unsigned int cc_to_fwcap_pause(unsigned int cc_pause) +{ + unsigned int fw_pause = 0; + + if (cc_pause & PAUSE_RX) + fw_pause |= FW_PORT_CAP_FC_RX; + if (cc_pause & PAUSE_TX) + fw_pause |= FW_PORT_CAP_FC_TX; + + return fw_pause; +} + +/* Translate Firmware Forward Error Correction specification to Common Code */ +static inline unsigned int fwcap_to_cc_fec(unsigned int fw_fec) +{ + unsigned int cc_fec = 0; + + if (fw_fec & FW_PORT_CAP_FEC_RS) + cc_fec |= FEC_RS; + if (fw_fec & FW_PORT_CAP_FEC_BASER_RS) + cc_fec |= FEC_BASER_RS; + + return cc_fec; +} + +/* Translate Common Code Forward Error Correction specification to Firmware */ +static inline unsigned int cc_to_fwcap_fec(unsigned int cc_fec) +{ + unsigned int fw_fec = 0; + + if (cc_fec & FEC_RS) + fw_fec |= FW_PORT_CAP_FEC_RS; + if (cc_fec & FEC_BASER_RS) + fw_fec |= FW_PORT_CAP_FEC_BASER_RS; + + return fw_fec; +} + /** * t4_link_l1cfg - apply link configuration to MAC/PHY - * @phy: the PHY to setup - * @mac: the MAC to setup - * @lc: the requested link configuration + * @adapter: the adapter + * @mbox: the Firmware Mailbox to use + * @port: the Port ID + * @lc: the Port's Link Configuration * * Set up a port's MAC and PHY according to a desired link configuration. * - If the PHY can auto-negotiate first decide what to advertise, then @@ -3857,22 +3910,46 @@ int t4_link_l1cfg(struct adapter *adap, unsigned int mbox, unsigned int port, struct link_config *lc) { struct fw_port_cmd c; - unsigned int mdi = FW_PORT_CAP_MDI_V(FW_PORT_CAP_MDI_AUTO); - unsigned int fc = 0, fec = 0, fw_fec = 0; + unsigned int fw_mdi = FW_PORT_CAP_MDI_V(FW_PORT_CAP_MDI_AUTO); + unsigned int fw_fc, cc_fec, fw_fec; + unsigned int rcap; lc->link_ok = 0; - if (lc->requested_fc & PAUSE_RX) - fc |= FW_PORT_CAP_FC_RX; - if (lc->requested_fc & PAUSE_TX) - fc |= FW_PORT_CAP_FC_TX; - fec = lc->requested_fec & FEC_AUTO ? lc->auto_fec : lc->requested_fec; + /* Convert driver coding of Pause Frame Flow Control settings into the + * Firmware's API. + */ + fw_fc = cc_to_fwcap_pause(lc->requested_fc); - if (fec & FEC_RS) - fw_fec |= FW_PORT_CAP_FEC_RS; - if (fec & FEC_BASER_RS) - fw_fec |= FW_PORT_CAP_FEC_BASER_RS; + /* Convert Common Code Forward Error Control settings into the + * Firmware's API. If the current Requested FEC has "Automatic" + * (IEEE 802.3) specified, then we use whatever the Firmware + * sent us as part of it's IEEE 802.3-based interpratation of + * the Transceiver Module EPROM FEC parameters. Otherwise we + * use whatever is in the current Requested FEC settings. + */ + if (lc->requested_fec & FEC_AUTO) + cc_fec = lc->auto_fec; + else + cc_fec = lc->requested_fec; + fw_fec = cc_to_fwcap_fec(cc_fec); + /* Figure out what our Requested Port Capabilities are going to be. + */ + if (!(lc->supported & FW_PORT_CAP_ANEG)) { + rcap = (lc->supported & ADVERT_MASK) | fw_fc | fw_fec; + lc->fc = lc->requested_fc & (PAUSE_RX | PAUSE_TX); + lc->fec = cc_fec; + } else if (lc->autoneg == AUTONEG_DISABLE) { + rcap = lc->requested_speed | fw_fc | fw_fec | fw_mdi; + lc->fc = lc->requested_fc & (PAUSE_RX | PAUSE_TX); + lc->fec = cc_fec; + } else { + rcap = lc->advertising | fw_fc | fw_fec | fw_mdi; + } + + /* And send that on to the Firmware ... + */ memset(&c, 0, sizeof(c)); c.op_to_portid = cpu_to_be32(FW_CMD_OP_V(FW_PORT_CMD) | FW_CMD_REQUEST_F | FW_CMD_EXEC_F | @@ -3880,19 +3957,7 @@ int t4_link_l1cfg(struct adapter *adap, unsigned int mbox, unsigned int port, c.action_to_len16 = cpu_to_be32(FW_PORT_CMD_ACTION_V(FW_PORT_ACTION_L1_CFG) | FW_LEN16(c)); - - if (!(lc->supported & FW_PORT_CAP_ANEG)) { - c.u.l1cfg.rcap = cpu_to_be32((lc->supported & ADVERT_MASK) | - fc | fw_fec); - lc->fc = lc->requested_fc & (PAUSE_RX | PAUSE_TX); - } else if (lc->autoneg == AUTONEG_DISABLE) { - c.u.l1cfg.rcap = cpu_to_be32(lc->requested_speed | fc | - fw_fec | mdi); - lc->fc = lc->requested_fc & (PAUSE_RX | PAUSE_TX); - } else - c.u.l1cfg.rcap = cpu_to_be32(lc->advertising | fc | - fw_fec | mdi); - + c.u.l1cfg.rcap = cpu_to_be32(rcap); return t4_wr_mbox(adap, mbox, &c, sizeof(c), NULL); } @@ -7630,19 +7695,28 @@ static const char *t4_link_down_rc_str(unsigned char link_down_rc) void t4_handle_get_port_info(struct port_info *pi, const __be64 *rpl) { const struct fw_port_cmd *p = (const void *)rpl; + unsigned int acaps = be16_to_cpu(p->u.info.acap); struct adapter *adap = pi->adapter; /* link/module state change message */ - int speed = 0, fc = 0; + int speed = 0, fc, fec; struct link_config *lc; u32 stat = be32_to_cpu(p->u.info.lstatus_to_modtype); int link_ok = (stat & FW_PORT_CMD_LSTATUS_F) != 0; u32 mod = FW_PORT_CMD_MODTYPE_G(stat); + /* Unfortunately the format of the Link Status returned by the + * Firmware isn't the same as the Firmware Port Capabilities bitfield + * used everywhere else ... + */ + fc = 0; if (stat & FW_PORT_CMD_RXPAUSE_F) fc |= PAUSE_RX; if (stat & FW_PORT_CMD_TXPAUSE_F) fc |= PAUSE_TX; + + fec = fwcap_to_cc_fec(acaps); + if (stat & FW_PORT_CMD_LSPEED_V(FW_PORT_CAP_SPEED_100M)) speed = 100; else if (stat & FW_PORT_CMD_LSPEED_V(FW_PORT_CAP_SPEED_1G)) @@ -7659,11 +7733,20 @@ void t4_handle_get_port_info(struct port_info *pi, const __be64 *rpl) lc = &pi->link_cfg; if (mod != pi->mod_type) { + /* When a new Transceiver Module is inserted, the Firmware + * will examine any Forward Error Correction parameters + * present in the Transceiver Module i2c EPROM and determine + * the supported and recommended FEC settings from those + * based on IEEE 802.3 standards. We always record the + * IEEE 802.3 recommended "automatic" settings. + */ + lc->auto_fec = fec; + pi->mod_type = mod; t4_os_portmod_changed(adap, pi->port_id); } if (link_ok != lc->link_ok || speed != lc->speed || - fc != lc->fc) { /* something changed */ + fc != lc->fc || fec != lc->fec) { /* something changed */ if (!link_ok && lc->link_ok) { unsigned char rc = FW_PORT_CMD_LINKDNRC_G(stat); @@ -7675,6 +7758,8 @@ void t4_handle_get_port_info(struct port_info *pi, const __be64 *rpl) lc->link_ok = link_ok; lc->speed = speed; lc->fc = fc; + lc->fec = fec; + lc->supported = be16_to_cpu(p->u.info.pcap); lc->lp_advertising = be16_to_cpu(p->u.info.lpacap); @@ -7764,7 +7849,8 @@ static void get_pci_mode(struct adapter *adapter, struct pci_params *p) /** * init_link_config - initialize a link's SW state * @lc: structure holding the link state - * @caps: link capabilities + * @pcaps: link Port Capabilities + * @acaps: link current Advertised Port Capabilities * * Initializes the SW state maintained for each link, including the link's * capabilities and default speed/flow-control/autonegotiation settings. @@ -7777,15 +7863,11 @@ static void init_link_config(struct link_config *lc, unsigned int pcaps, lc->requested_speed = 0; lc->speed = 0; lc->requested_fc = lc->fc = PAUSE_RX | PAUSE_TX; - lc->auto_fec = 0; /* For Forward Error Control, we default to whatever the Firmware * tells us the Link is currently advertising. */ - if (acaps & FW_PORT_CAP_FEC_RS) - lc->auto_fec |= FEC_RS; - if (acaps & FW_PORT_CAP_FEC_BASER_RS) - lc->auto_fec |= FEC_BASER_RS; + lc->auto_fec = fwcap_to_cc_fec(acaps); lc->requested_fec = FEC_AUTO; lc->fec = lc->auto_fec; diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h index 83cc9863444b..afdbb701fdb4 100644 --- a/include/linux/ethtool.h +++ b/include/linux/ethtool.h @@ -374,5 +374,9 @@ struct ethtool_ops { struct ethtool_link_ksettings *); int (*set_link_ksettings)(struct net_device *, const struct ethtool_link_ksettings *); + int (*get_fecparam)(struct net_device *, + struct ethtool_fecparam *); + int (*set_fecparam)(struct net_device *, + struct ethtool_fecparam *); }; #endif /* _LINUX_ETHTOOL_H */ diff --git a/include/uapi/linux/ethtool.h b/include/uapi/linux/ethtool.h index 7d4a594d5d58..9c041dae8e2c 100644 --- a/include/uapi/linux/ethtool.h +++ b/include/uapi/linux/ethtool.h @@ -1238,6 +1238,47 @@ struct ethtool_per_queue_op { char data[]; }; +/** + * struct ethtool_fecparam - Ethernet forward error correction(fec) parameters + * @cmd: Command number = %ETHTOOL_GFECPARAM or %ETHTOOL_SFECPARAM + * @active_fec: FEC mode which is active on porte + * @fec: Bitmask of supported/configured FEC modes + * @rsvd: Reserved for future extensions. i.e FEC bypass feature. + * + * Drivers should reject a non-zero setting of @autoneg when + * autoneogotiation is disabled (or not supported) for the link. + * + */ +struct ethtool_fecparam { + __u32 cmd; + /* bitmask of FEC modes */ + __u32 active_fec; + __u32 fec; + __u32 reserved; +}; + +/** + * enum ethtool_fec_config_bits - flags definition of ethtool_fec_configuration + * @ETHTOOL_FEC_NONE: FEC mode configuration is not supported + * @ETHTOOL_FEC_AUTO: Default/Best FEC mode provided by driver + * @ETHTOOL_FEC_OFF: No FEC Mode + * @ETHTOOL_FEC_RS: Reed-Solomon Forward Error Detection mode + * @ETHTOOL_FEC_BASER: Base-R/Reed-Solomon Forward Error Detection mode + */ +enum ethtool_fec_config_bits { + ETHTOOL_FEC_NONE_BIT, + ETHTOOL_FEC_AUTO_BIT, + ETHTOOL_FEC_OFF_BIT, + ETHTOOL_FEC_RS_BIT, + ETHTOOL_FEC_BASER_BIT, +}; + +#define ETHTOOL_FEC_NONE (1 << ETHTOOL_FEC_NONE_BIT) +#define ETHTOOL_FEC_AUTO (1 << ETHTOOL_FEC_AUTO_BIT) +#define ETHTOOL_FEC_OFF (1 << ETHTOOL_FEC_OFF_BIT) +#define ETHTOOL_FEC_RS (1 << ETHTOOL_FEC_RS_BIT) +#define ETHTOOL_FEC_BASER (1 << ETHTOOL_FEC_BASER_BIT) + /* CMDs currently supported */ #define ETHTOOL_GSET 0x00000001 /* DEPRECATED, Get settings. * Please use ETHTOOL_GLINKSETTINGS @@ -1330,6 +1371,8 @@ struct ethtool_per_queue_op { #define ETHTOOL_SLINKSETTINGS 0x0000004d /* Set ethtool_link_settings */ #define ETHTOOL_PHY_GTUNABLE 0x0000004e /* Get PHY tunable configuration */ #define ETHTOOL_PHY_STUNABLE 0x0000004f /* Set PHY tunable configuration */ +#define ETHTOOL_GFECPARAM 0x00000050 /* Get FEC settings */ +#define ETHTOOL_SFECPARAM 0x00000051 /* Set FEC settings */ /* compatibility with older code */ #define SPARC_ETH_GSET ETHTOOL_GSET @@ -1387,6 +1430,9 @@ enum ethtool_link_mode_bit_indices { ETHTOOL_LINK_MODE_2500baseT_Full_BIT = 47, ETHTOOL_LINK_MODE_5000baseT_Full_BIT = 48, + ETHTOOL_LINK_MODE_FEC_NONE_BIT = 49, + ETHTOOL_LINK_MODE_FEC_RS_BIT = 50, + ETHTOOL_LINK_MODE_FEC_BASER_BIT = 51, /* Last allowed bit for __ETHTOOL_LINK_MODE_LEGACY_MASK is bit * 31. Please do NOT define any SUPPORTED_* or ADVERTISED_* @@ -1395,7 +1441,7 @@ enum ethtool_link_mode_bit_indices { */ __ETHTOOL_LINK_MODE_LAST - = ETHTOOL_LINK_MODE_5000baseT_Full_BIT, + = ETHTOOL_LINK_MODE_FEC_BASER_BIT, }; #define __ETHTOOL_LINK_MODE_LEGACY_MASK(base_name) \ diff --git a/net/core/ethtool.c b/net/core/ethtool.c index b987bc475fc8..6a582ae4c5d9 100644 --- a/net/core/ethtool.c +++ b/net/core/ethtool.c @@ -2512,6 +2512,33 @@ static int set_phy_tunable(struct net_device *dev, void __user *useraddr) return ret; } +static int ethtool_get_fecparam(struct net_device *dev, void __user *useraddr) +{ + struct ethtool_fecparam fecparam = { ETHTOOL_GFECPARAM }; + + if (!dev->ethtool_ops->get_fecparam) + return -EOPNOTSUPP; + + dev->ethtool_ops->get_fecparam(dev, &fecparam); + + if (copy_to_user(useraddr, &fecparam, sizeof(fecparam))) + return -EFAULT; + return 0; +} + +static int ethtool_set_fecparam(struct net_device *dev, void __user *useraddr) +{ + struct ethtool_fecparam fecparam; + + if (!dev->ethtool_ops->set_fecparam) + return -EOPNOTSUPP; + + if (copy_from_user(&fecparam, useraddr, sizeof(fecparam))) + return -EFAULT; + + return dev->ethtool_ops->set_fecparam(dev, &fecparam); +} + /* The main entry point in this file. Called from net/core/dev_ioctl.c */ int dev_ethtool(struct net *net, struct ifreq *ifr) @@ -2570,6 +2597,7 @@ int dev_ethtool(struct net *net, struct ifreq *ifr) case ETHTOOL_GTUNABLE: case ETHTOOL_PHY_GTUNABLE: case ETHTOOL_GLINKSETTINGS: + case ETHTOOL_GFECPARAM: break; default: if (!ns_capable(net->user_ns, CAP_NET_ADMIN)) @@ -2779,6 +2807,12 @@ int dev_ethtool(struct net *net, struct ifreq *ifr) case ETHTOOL_PHY_STUNABLE: rc = set_phy_tunable(dev, useraddr); break; + case ETHTOOL_GFECPARAM: + rc = ethtool_get_fecparam(dev, useraddr); + break; + case ETHTOOL_SFECPARAM: + rc = ethtool_set_fecparam(dev, useraddr); + break; default: rc = -EOPNOTSUPP; }