diff --git a/drivers/power/supply/ab8500-bm.h b/drivers/power/supply/ab8500-bm.h
index 58e4cb901076..c8841567dfee 100644
--- a/drivers/power/supply/ab8500-bm.h
+++ b/drivers/power/supply/ab8500-bm.h
@@ -160,13 +160,6 @@
 #define BTEMP_HIGH_TH_57_1		0x02
 #define BTEMP_HIGH_TH_62		0x03
 
-/* current is mA */
-#define USB_0P1A			100
-#define USB_0P2A			200
-#define USB_0P3A			300
-#define USB_0P4A			400
-#define USB_0P5A			500
-
 #define LOW_BAT_3P1V			0x20
 #define LOW_BAT_2P3V			0x00
 #define LOW_BAT_RESET			0x01
@@ -359,22 +352,21 @@ struct ab8500_fg_parameters {
 /**
  * struct ab8500_charger_maximization - struct used by the board config.
  * @use_maxi:		Enable maximization for this battery type
- * @maxi_chg_curr:	Maximum charger current allowed
+ * @maxi_chg_curr_ua:	Maximum charger current allowed in microampere
  * @maxi_wait_cycles:	cycles to wait before setting charger current
- * @charger_curr_step	delta between two charger current settings (mA)
+ * @charger_curr_step_ua: delta between two charger current settings (uA)
  */
 struct ab8500_maxim_parameters {
 	bool ena_maxi;
-	int chg_curr;
+	int chg_curr_ua;
 	int wait_cycles;
-	int charger_curr_step;
+	int charger_curr_step_ua;
 };
 
 /**
  * struct ab8500_battery_type - different batteries supported
  * @resis_high:			battery upper resistance limit
  * @resis_low:			battery lower resistance limit
- * @normal_cur_lvl:		charger current in normal state in mA
  * @normal_vol_lvl:		charger voltage in normal state in mV
  * @maint_a_cur_lvl:		charger current in maintenance A state in mA
  * @maint_a_vol_lvl:		charger voltage in maintenance A state in mV
@@ -394,7 +386,6 @@ struct ab8500_maxim_parameters {
 struct ab8500_battery_type {
 	int resis_high;
 	int resis_low;
-	int normal_cur_lvl;
 	int normal_vol_lvl;
 	int maint_a_cur_lvl;
 	int maint_a_vol_lvl;
@@ -431,15 +422,15 @@ struct ab8500_bm_capacity_levels {
 /**
  * struct ab8500_bm_charger_parameters - Charger specific parameters
  * @usb_volt_max:	maximum allowed USB charger voltage in mV
- * @usb_curr_max:	maximum allowed USB charger current in mA
+ * @usb_curr_max_ua:	maximum allowed USB charger current in uA
  * @ac_volt_max:	maximum allowed AC charger voltage in mV
- * @ac_curr_max:	maximum allowed AC charger current in mA
+ * @ac_curr_max_ua:	maximum allowed AC charger current in uA
  */
 struct ab8500_bm_charger_parameters {
 	int usb_volt_max;
-	int usb_curr_max;
+	int usb_curr_max_ua;
 	int ac_volt_max;
-	int ac_curr_max;
+	int ac_curr_max_ua;
 };
 
 /**
diff --git a/drivers/power/supply/ab8500-chargalg.h b/drivers/power/supply/ab8500-chargalg.h
index 07e6ff50084f..8094a3c2bd3a 100644
--- a/drivers/power/supply/ab8500-chargalg.h
+++ b/drivers/power/supply/ab8500-chargalg.h
@@ -32,7 +32,7 @@ struct ux500_charger_ops {
  * @psy			power supply base class
  * @ops			ux500 charger operations
  * @max_out_volt	maximum output charger voltage in mV
- * @max_out_curr	maximum output charger current in mA
+ * @max_out_curr_ua	maximum output charger current in uA
  * @enabled		indicates if this charger is used or not
  * @external		external charger unit (pm2xxx)
  */
@@ -40,7 +40,7 @@ struct ux500_charger {
 	struct power_supply *psy;
 	struct ux500_charger_ops ops;
 	int max_out_volt;
-	int max_out_curr;
+	int max_out_curr_ua;
 	int wdt_refresh;
 	bool enabled;
 	bool external;
diff --git a/drivers/power/supply/ab8500_bmdata.c b/drivers/power/supply/ab8500_bmdata.c
index 78182a396de7..e9bbb7517e04 100644
--- a/drivers/power/supply/ab8500_bmdata.c
+++ b/drivers/power/supply/ab8500_bmdata.c
@@ -83,7 +83,6 @@ static const struct batres_vs_temp temp_to_batres_tbl_thermistor[] = {
 static struct ab8500_battery_type bat_type_thermistor_unknown = {
 	.resis_high = 0,
 	.resis_low = 0,
-	.normal_cur_lvl = 400,
 	.normal_vol_lvl = 4100,
 	.maint_a_cur_lvl = 400,
 	.maint_a_vol_lvl = 4050,
@@ -133,16 +132,16 @@ static const struct ab8500_fg_parameters fg = {
 
 static const struct ab8500_maxim_parameters ab8500_maxi_params = {
 	.ena_maxi = true,
-	.chg_curr = 910,
+	.chg_curr_ua = 910000,
 	.wait_cycles = 10,
-	.charger_curr_step = 100,
+	.charger_curr_step_ua = 100000,
 };
 
 static const struct ab8500_bm_charger_parameters chg = {
 	.usb_volt_max		= 5500,
-	.usb_curr_max		= 1500,
+	.usb_curr_max_ua	= 1500000,
 	.ac_volt_max		= 7500,
-	.ac_curr_max		= 1500,
+	.ac_curr_max_ua		= 1500000,
 };
 
 /* This is referenced directly in the charger code */
@@ -201,6 +200,9 @@ int ab8500_bm_of_probe(struct power_supply *psy,
 		bi->overvoltage_limit_uv = 4050000;
 	}
 
+	if (bi->constant_charge_current_max_ua < 0)
+		bi->constant_charge_current_max_ua = 400000;
+
 	if (bi->charge_term_current_ua)
 		/* Charging stops when we drop below this current */
 		bi->charge_term_current_ua = 200000;
diff --git a/drivers/power/supply/ab8500_chargalg.c b/drivers/power/supply/ab8500_chargalg.c
index 90974a8887cd..8ad3924ee496 100644
--- a/drivers/power/supply/ab8500_chargalg.c
+++ b/drivers/power/supply/ab8500_chargalg.c
@@ -46,8 +46,8 @@
 /* Five minutes expressed in seconds */
 #define FIVE_MINUTES_IN_SECONDS        300
 
-#define CHARGALG_CURR_STEP_LOW		0
-#define CHARGALG_CURR_STEP_HIGH	100
+#define CHARGALG_CURR_STEP_LOW_UA	0
+#define CHARGALG_CURR_STEP_HIGH_UA	100000
 
 /*
  * This is the battery capacity limit that will trigger a new
@@ -71,13 +71,13 @@ struct ab8500_chargalg_charger_info {
 	bool usb_chg_ok;
 	bool ac_chg_ok;
 	int usb_volt;
-	int usb_curr;
+	int usb_curr_ua;
 	int ac_volt;
-	int ac_curr;
+	int ac_curr_ua;
 	int usb_vset;
-	int usb_iset;
+	int usb_iset_ua;
 	int ac_vset;
-	int ac_iset;
+	int ac_iset_ua;
 };
 
 struct ab8500_chargalg_suspension_status {
@@ -88,14 +88,14 @@ struct ab8500_chargalg_suspension_status {
 
 struct ab8500_chargalg_current_step_status {
 	bool curr_step_change;
-	int curr_step;
+	int curr_step_ua;
 };
 
 struct ab8500_chargalg_battery_data {
 	int temp;
 	int volt_uv;
 	int avg_curr_ua;
-	int inst_curr;
+	int inst_curr_ua;
 	int percent;
 };
 
@@ -184,13 +184,13 @@ struct ab8500_chargalg_events {
 
 /**
  * struct ab8500_charge_curr_maximization - Charger maximization parameters
- * @original_iset:	the non optimized/maximised charger current
- * @current_iset:	the charging current used at this moment
- * @test_delta_i:	the delta between the current we want to charge and the
+ * @original_iset_ua:	the non optimized/maximised charger current
+ * @current_iset_ua:	the charging current used at this moment
+ * @test_delta_i_ua:	the delta between the current we want to charge and the
 			current that is really going into the battery
  * @condition_cnt:	number of iterations needed before a new charger current
 			is set
- * @max_current:	maximum charger current
+ * @max_current_ua:	maximum charger current
  * @wait_cnt:		to avoid too fast current step down in case of charger
  *			voltage collapse, we insert this delay between step
  *			down
@@ -198,11 +198,11 @@ struct ab8500_chargalg_events {
 			increased
  */
 struct ab8500_charge_curr_maximization {
-	int original_iset;
-	int current_iset;
-	int test_delta_i;
+	int original_iset_ua;
+	int current_iset_ua;
+	int test_delta_i_ua;
 	int condition_cnt;
-	int max_current;
+	int max_current_ua;
 	int wait_cnt;
 	u8 level;
 };
@@ -352,6 +352,8 @@ static void ab8500_chargalg_state_to(struct ab8500_chargalg *di,
 
 static int ab8500_chargalg_check_charger_enable(struct ab8500_chargalg *di)
 {
+	struct power_supply_battery_info *bi = &di->bm->bi;
+
 	switch (di->charge_state) {
 	case STATE_NORMAL:
 	case STATE_MAINTENANCE_A:
@@ -364,12 +366,12 @@ static int ab8500_chargalg_check_charger_enable(struct ab8500_chargalg *di)
 	if (di->chg_info.charger_type & USB_CHG) {
 		return di->usb_chg->ops.check_enable(di->usb_chg,
 			di->bm->bat_type->normal_vol_lvl,
-			di->bm->bat_type->normal_cur_lvl);
+			bi->constant_charge_current_max_ua);
 	} else if ((di->chg_info.charger_type & AC_CHG) &&
 		   !(di->ac_chg->external)) {
 		return di->ac_chg->ops.check_enable(di->ac_chg,
 			di->bm->bat_type->normal_vol_lvl,
-			di->bm->bat_type->normal_cur_lvl);
+			bi->constant_charge_current_max_ua);
 	}
 	return 0;
 }
@@ -545,13 +547,13 @@ static int ab8500_chargalg_kick_watchdog(struct ab8500_chargalg *di)
  * @di:		pointer to the ab8500_chargalg structure
  * @enable:	charger on/off
  * @vset:	requested charger output voltage
- * @iset:	requested charger output current
+ * @iset_ua:	requested charger output current in microampere
  *
  * The AC charger will be turned on/off with the requested charge voltage and
  * current
  */
 static int ab8500_chargalg_ac_en(struct ab8500_chargalg *di, int enable,
-	int vset, int iset)
+	int vset, int iset_ua)
 {
 	static int ab8500_chargalg_ex_ac_enable_toggle;
 
@@ -561,10 +563,10 @@ static int ab8500_chargalg_ac_en(struct ab8500_chargalg *di, int enable,
 	/* Select maximum of what both the charger and the battery supports */
 	if (di->ac_chg->max_out_volt)
 		vset = min(vset, di->ac_chg->max_out_volt);
-	if (di->ac_chg->max_out_curr)
-		iset = min(iset, di->ac_chg->max_out_curr);
+	if (di->ac_chg->max_out_curr_ua)
+		iset_ua = min(iset_ua, di->ac_chg->max_out_curr_ua);
 
-	di->chg_info.ac_iset = iset;
+	di->chg_info.ac_iset_ua = iset_ua;
 	di->chg_info.ac_vset = vset;
 
 	/* Enable external charger */
@@ -575,7 +577,7 @@ static int ab8500_chargalg_ac_en(struct ab8500_chargalg *di, int enable,
 		ab8500_chargalg_ex_ac_enable_toggle++;
 	}
 
-	return di->ac_chg->ops.enable(di->ac_chg, enable, vset, iset);
+	return di->ac_chg->ops.enable(di->ac_chg, enable, vset, iset_ua);
 }
 
 /**
@@ -583,13 +585,13 @@ static int ab8500_chargalg_ac_en(struct ab8500_chargalg *di, int enable,
  * @di:		pointer to the ab8500_chargalg structure
  * @enable:	charger on/off
  * @vset:	requested charger output voltage
- * @iset:	requested charger output current
+ * @iset_ua:	requested charger output current in microampere
  *
  * The USB charger will be turned on/off with the requested charge voltage and
  * current
  */
 static int ab8500_chargalg_usb_en(struct ab8500_chargalg *di, int enable,
-	int vset, int iset)
+	int vset, int iset_ua)
 {
 	if (!di->usb_chg || !di->usb_chg->ops.enable)
 		return -ENXIO;
@@ -597,25 +599,25 @@ static int ab8500_chargalg_usb_en(struct ab8500_chargalg *di, int enable,
 	/* Select maximum of what both the charger and the battery supports */
 	if (di->usb_chg->max_out_volt)
 		vset = min(vset, di->usb_chg->max_out_volt);
-	if (di->usb_chg->max_out_curr)
-		iset = min(iset, di->usb_chg->max_out_curr);
+	if (di->usb_chg->max_out_curr_ua)
+		iset_ua = min(iset_ua, di->usb_chg->max_out_curr_ua);
 
-	di->chg_info.usb_iset = iset;
+	di->chg_info.usb_iset_ua = iset_ua;
 	di->chg_info.usb_vset = vset;
 
-	return di->usb_chg->ops.enable(di->usb_chg, enable, vset, iset);
+	return di->usb_chg->ops.enable(di->usb_chg, enable, vset, iset_ua);
 }
 
 /**
  * ab8500_chargalg_update_chg_curr() - Update charger current
  * @di:		pointer to the ab8500_chargalg structure
- * @iset:	requested charger output current
+ * @iset_ua:	requested charger output current in microampere
  *
  * The charger output current will be updated for the charger
  * that is currently in use
  */
 static int ab8500_chargalg_update_chg_curr(struct ab8500_chargalg *di,
-		int iset)
+		int iset_ua)
 {
 	/* Check if charger exists and update current if charging */
 	if (di->ac_chg && di->ac_chg->ops.update_curr &&
@@ -624,24 +626,24 @@ static int ab8500_chargalg_update_chg_curr(struct ab8500_chargalg *di,
 		 * Select maximum of what both the charger
 		 * and the battery supports
 		 */
-		if (di->ac_chg->max_out_curr)
-			iset = min(iset, di->ac_chg->max_out_curr);
+		if (di->ac_chg->max_out_curr_ua)
+			iset_ua = min(iset_ua, di->ac_chg->max_out_curr_ua);
 
-		di->chg_info.ac_iset = iset;
+		di->chg_info.ac_iset_ua = iset_ua;
 
-		return di->ac_chg->ops.update_curr(di->ac_chg, iset);
+		return di->ac_chg->ops.update_curr(di->ac_chg, iset_ua);
 	} else if (di->usb_chg && di->usb_chg->ops.update_curr &&
 			di->chg_info.charger_type & USB_CHG) {
 		/*
 		 * Select maximum of what both the charger
 		 * and the battery supports
 		 */
-		if (di->usb_chg->max_out_curr)
-			iset = min(iset, di->usb_chg->max_out_curr);
+		if (di->usb_chg->max_out_curr_ua)
+			iset_ua = min(iset_ua, di->usb_chg->max_out_curr_ua);
 
-		di->chg_info.usb_iset = iset;
+		di->chg_info.usb_iset_ua = iset_ua;
 
-		return di->usb_chg->ops.update_curr(di->usb_chg, iset);
+		return di->usb_chg->ops.update_curr(di->usb_chg, iset_ua);
 	}
 
 	return -ENXIO;
@@ -691,27 +693,27 @@ static void ab8500_chargalg_hold_charging(struct ab8500_chargalg *di)
  * ab8500_chargalg_start_charging() - Start the charger
  * @di:		pointer to the ab8500_chargalg structure
  * @vset:	requested charger output voltage
- * @iset:	requested charger output current
+ * @iset_ua:	requested charger output current in microampere
  *
  * A charger will be enabled depending on the requested charger type that was
  * detected previously.
  */
 static void ab8500_chargalg_start_charging(struct ab8500_chargalg *di,
-	int vset, int iset)
+	int vset, int iset_ua)
 {
 	switch (di->chg_info.charger_type) {
 	case AC_CHG:
 		dev_dbg(di->dev,
-			"AC parameters: Vset %d, Ich %d\n", vset, iset);
+			"AC parameters: Vset %d, Ich %d\n", vset, iset_ua);
 		ab8500_chargalg_usb_en(di, false, 0, 0);
-		ab8500_chargalg_ac_en(di, true, vset, iset);
+		ab8500_chargalg_ac_en(di, true, vset, iset_ua);
 		break;
 
 	case USB_CHG:
 		dev_dbg(di->dev,
-			"USB parameters: Vset %d, Ich %d\n", vset, iset);
+			"USB parameters: Vset %d, Ich %d\n", vset, iset_ua);
 		ab8500_chargalg_ac_en(di, false, 0, 0);
-		ab8500_chargalg_usb_en(di, true, vset, iset);
+		ab8500_chargalg_usb_en(di, true, vset, iset_ua);
 		break;
 
 	default:
@@ -825,12 +827,12 @@ static void ab8500_chargalg_end_of_charge(struct ab8500_chargalg *di)
 
 static void init_maxim_chg_curr(struct ab8500_chargalg *di)
 {
-	di->ccm.original_iset =
-		di->bm->bat_type->normal_cur_lvl;
-	di->ccm.current_iset =
-		di->bm->bat_type->normal_cur_lvl;
-	di->ccm.test_delta_i = di->bm->maxi->charger_curr_step;
-	di->ccm.max_current = di->bm->maxi->chg_curr;
+	struct power_supply_battery_info *bi = &di->bm->bi;
+
+	di->ccm.original_iset_ua = bi->constant_charge_current_max_ua;
+	di->ccm.current_iset_ua = bi->constant_charge_current_max_ua;
+	di->ccm.test_delta_i_ua = di->bm->maxi->charger_curr_step_ua;
+	di->ccm.max_current_ua = di->bm->maxi->chg_curr_ua;
 	di->ccm.condition_cnt = di->bm->maxi->wait_cycles;
 	di->ccm.level = 0;
 }
@@ -846,12 +848,12 @@ static void init_maxim_chg_curr(struct ab8500_chargalg *di)
  */
 static enum maxim_ret ab8500_chargalg_chg_curr_maxim(struct ab8500_chargalg *di)
 {
-	int delta_i;
+	int delta_i_ua;
 
 	if (!di->bm->maxi->ena_maxi)
 		return MAXIM_RET_NOACTION;
 
-	delta_i = di->ccm.original_iset - di->batt_data.inst_curr;
+	delta_i_ua = di->ccm.original_iset_ua - di->batt_data.inst_curr_ua;
 
 	if (di->events.vbus_collapsed) {
 		dev_dbg(di->dev, "Charger voltage has collapsed %d\n",
@@ -860,9 +862,9 @@ static enum maxim_ret ab8500_chargalg_chg_curr_maxim(struct ab8500_chargalg *di)
 			dev_dbg(di->dev, "lowering current\n");
 			di->ccm.wait_cnt++;
 			di->ccm.condition_cnt = di->bm->maxi->wait_cycles;
-			di->ccm.max_current =
-				di->ccm.current_iset - di->ccm.test_delta_i;
-			di->ccm.current_iset = di->ccm.max_current;
+			di->ccm.max_current_ua =
+				di->ccm.current_iset_ua - di->ccm.test_delta_i_ua;
+			di->ccm.current_iset_ua = di->ccm.max_current_ua;
 			di->ccm.level--;
 			return MAXIM_RET_CHANGE;
 		} else {
@@ -875,36 +877,36 @@ static enum maxim_ret ab8500_chargalg_chg_curr_maxim(struct ab8500_chargalg *di)
 
 	di->ccm.wait_cnt = 0;
 
-	if (di->batt_data.inst_curr > di->ccm.original_iset) {
-		dev_dbg(di->dev, " Maximization Ibat (%dmA) too high"
-			" (limit %dmA) (current iset: %dmA)!\n",
-			di->batt_data.inst_curr, di->ccm.original_iset,
-			di->ccm.current_iset);
+	if (di->batt_data.inst_curr_ua > di->ccm.original_iset_ua) {
+		dev_dbg(di->dev, " Maximization Ibat (%duA) too high"
+			" (limit %duA) (current iset: %duA)!\n",
+			di->batt_data.inst_curr_ua, di->ccm.original_iset_ua,
+			di->ccm.current_iset_ua);
 
-		if (di->ccm.current_iset == di->ccm.original_iset)
+		if (di->ccm.current_iset_ua == di->ccm.original_iset_ua)
 			return MAXIM_RET_NOACTION;
 
 		di->ccm.condition_cnt = di->bm->maxi->wait_cycles;
-		di->ccm.current_iset = di->ccm.original_iset;
+		di->ccm.current_iset_ua = di->ccm.original_iset_ua;
 		di->ccm.level = 0;
 
 		return MAXIM_RET_IBAT_TOO_HIGH;
 	}
 
-	if (delta_i > di->ccm.test_delta_i &&
-		(di->ccm.current_iset + di->ccm.test_delta_i) <
-		di->ccm.max_current) {
+	if (delta_i_ua > di->ccm.test_delta_i_ua &&
+		(di->ccm.current_iset_ua + di->ccm.test_delta_i_ua) <
+		di->ccm.max_current_ua) {
 		if (di->ccm.condition_cnt-- == 0) {
 			/* Increse the iset with cco.test_delta_i */
 			di->ccm.condition_cnt = di->bm->maxi->wait_cycles;
-			di->ccm.current_iset += di->ccm.test_delta_i;
+			di->ccm.current_iset_ua += di->ccm.test_delta_i_ua;
 			di->ccm.level++;
 			dev_dbg(di->dev, " Maximization needed, increase"
-				" with %d mA to %dmA (Optimal ibat: %d)"
+				" with %d uA to %duA (Optimal ibat: %d uA)"
 				" Level %d\n",
-				di->ccm.test_delta_i,
-				di->ccm.current_iset,
-				di->ccm.original_iset,
+				di->ccm.test_delta_i_ua,
+				di->ccm.current_iset_ua,
+				di->ccm.original_iset_ua,
 				di->ccm.level);
 			return MAXIM_RET_CHANGE;
 		} else {
@@ -918,6 +920,7 @@ static enum maxim_ret ab8500_chargalg_chg_curr_maxim(struct ab8500_chargalg *di)
 
 static void handle_maxim_chg_curr(struct ab8500_chargalg *di)
 {
+	struct power_supply_battery_info *bi = &di->bm->bi;
 	enum maxim_ret ret;
 	int result;
 
@@ -925,13 +928,13 @@ static void handle_maxim_chg_curr(struct ab8500_chargalg *di)
 	switch (ret) {
 	case MAXIM_RET_CHANGE:
 		result = ab8500_chargalg_update_chg_curr(di,
-			di->ccm.current_iset);
+			di->ccm.current_iset_ua);
 		if (result)
 			dev_err(di->dev, "failed to set chg curr\n");
 		break;
 	case MAXIM_RET_IBAT_TOO_HIGH:
 		result = ab8500_chargalg_update_chg_curr(di,
-			di->bm->bat_type->normal_cur_lvl);
+			bi->constant_charge_current_max_ua);
 		if (result)
 			dev_err(di->dev, "failed to set chg curr\n");
 		break;
@@ -1226,15 +1229,13 @@ static int ab8500_chargalg_get_ext_psy_data(struct device *dev, void *data)
 		case POWER_SUPPLY_PROP_CURRENT_NOW:
 			switch (ext->desc->type) {
 			case POWER_SUPPLY_TYPE_MAINS:
-					di->chg_info.ac_curr =
-						ret.intval / 1000;
-					break;
+				di->chg_info.ac_curr_ua = ret.intval;
+				break;
 			case POWER_SUPPLY_TYPE_USB:
-					di->chg_info.usb_curr =
-						ret.intval / 1000;
+				di->chg_info.usb_curr_ua = ret.intval;
 				break;
 			case POWER_SUPPLY_TYPE_BATTERY:
-				di->batt_data.inst_curr = ret.intval / 1000;
+				di->batt_data.inst_curr_ua = ret.intval;
 				break;
 			default:
 				break;
@@ -1298,9 +1299,10 @@ static void ab8500_chargalg_external_power_changed(struct power_supply *psy)
  */
 static void ab8500_chargalg_algorithm(struct ab8500_chargalg *di)
 {
+	struct power_supply_battery_info *bi = &di->bm->bi;
 	int charger_status;
 	int ret;
-	int curr_step_lvl;
+	int curr_step_lvl_ua;
 
 	/* Collect data from all power_supply class devices */
 	class_for_each_device(power_supply_class, NULL,
@@ -1406,7 +1408,7 @@ static void ab8500_chargalg_algorithm(struct ab8500_chargalg *di)
 		"USB_I %d AC_Vset %d AC_Iset %d USB_Vset %d USB_Iset %d\n",
 		di->batt_data.volt_uv,
 		di->batt_data.avg_curr_ua,
-		di->batt_data.inst_curr,
+		di->batt_data.inst_curr_ua,
 		di->batt_data.temp,
 		di->batt_data.percent,
 		di->maintenance_chg,
@@ -1419,12 +1421,12 @@ static void ab8500_chargalg_algorithm(struct ab8500_chargalg *di)
 		di->chg_info.online_chg & USB_CHG,
 		di->events.ac_cv_active,
 		di->events.usb_cv_active,
-		di->chg_info.ac_curr,
-		di->chg_info.usb_curr,
+		di->chg_info.ac_curr_ua,
+		di->chg_info.usb_curr_ua,
 		di->chg_info.ac_vset,
-		di->chg_info.ac_iset,
+		di->chg_info.ac_iset_ua,
 		di->chg_info.usb_vset,
-		di->chg_info.usb_iset);
+		di->chg_info.usb_iset_ua);
 
 	switch (di->charge_state) {
 	case STATE_HANDHELD_INIT:
@@ -1509,15 +1511,15 @@ static void ab8500_chargalg_algorithm(struct ab8500_chargalg *di)
 		break;
 
 	case STATE_NORMAL_INIT:
-		if (di->curr_status.curr_step == CHARGALG_CURR_STEP_LOW)
+		if (di->curr_status.curr_step_ua == CHARGALG_CURR_STEP_LOW_UA)
 			ab8500_chargalg_stop_charging(di);
 		else {
-			curr_step_lvl = di->bm->bat_type->normal_cur_lvl
-				* di->curr_status.curr_step
-				/ CHARGALG_CURR_STEP_HIGH;
+			curr_step_lvl_ua = bi->constant_charge_current_max_ua
+				* di->curr_status.curr_step_ua
+				/ CHARGALG_CURR_STEP_HIGH_UA;
 			ab8500_chargalg_start_charging(di,
 				di->bm->bat_type->normal_vol_lvl,
-				curr_step_lvl);
+				curr_step_lvl_ua);
 		}
 
 		ab8500_chargalg_state_to(di, STATE_NORMAL);
@@ -1743,7 +1745,7 @@ static int ab8500_chargalg_get_property(struct power_supply *psy,
 static ssize_t ab8500_chargalg_curr_step_show(struct ab8500_chargalg *di,
 					      char *buf)
 {
-	return sprintf(buf, "%d\n", di->curr_status.curr_step);
+	return sprintf(buf, "%d\n", di->curr_status.curr_step_ua);
 }
 
 static ssize_t ab8500_chargalg_curr_step_store(struct ab8500_chargalg *di,
@@ -1756,9 +1758,9 @@ static ssize_t ab8500_chargalg_curr_step_store(struct ab8500_chargalg *di,
 	if (ret < 0)
 		return ret;
 
-	di->curr_status.curr_step = param;
-	if (di->curr_status.curr_step >= CHARGALG_CURR_STEP_LOW &&
-		di->curr_status.curr_step <= CHARGALG_CURR_STEP_HIGH) {
+	di->curr_status.curr_step_ua = param;
+	if (di->curr_status.curr_step_ua >= CHARGALG_CURR_STEP_LOW_UA &&
+		di->curr_status.curr_step_ua <= CHARGALG_CURR_STEP_HIGH_UA) {
 		di->curr_status.curr_step_change = true;
 		queue_work(di->chargalg_wq, &di->chargalg_work);
 	} else
@@ -2055,7 +2057,7 @@ static int ab8500_chargalg_probe(struct platform_device *pdev)
 		dev_err(di->dev, "failed to create sysfs entry\n");
 		return ret;
 	}
-	di->curr_status.curr_step = CHARGALG_CURR_STEP_HIGH;
+	di->curr_status.curr_step_ua = CHARGALG_CURR_STEP_HIGH_UA;
 
 	dev_info(di->dev, "probe success\n");
 	return component_add(dev, &ab8500_chargalg_component_ops);
diff --git a/drivers/power/supply/ab8500_charger.c b/drivers/power/supply/ab8500_charger.c
index 7a151cd97399..e66091f3f606 100644
--- a/drivers/power/supply/ab8500_charger.c
+++ b/drivers/power/supply/ab8500_charger.c
@@ -145,23 +145,23 @@ enum ab8500_usb_state {
 	AB8500_BM_USB_STATE_MAX,
 };
 
-/* VBUS input current limits supported in AB8500 in mA */
-#define USB_CH_IP_CUR_LVL_0P05		50
-#define USB_CH_IP_CUR_LVL_0P09		98
-#define USB_CH_IP_CUR_LVL_0P19		193
-#define USB_CH_IP_CUR_LVL_0P29		290
-#define USB_CH_IP_CUR_LVL_0P38		380
-#define USB_CH_IP_CUR_LVL_0P45		450
-#define USB_CH_IP_CUR_LVL_0P5		500
-#define USB_CH_IP_CUR_LVL_0P6		600
-#define USB_CH_IP_CUR_LVL_0P7		700
-#define USB_CH_IP_CUR_LVL_0P8		800
-#define USB_CH_IP_CUR_LVL_0P9		900
-#define USB_CH_IP_CUR_LVL_1P0		1000
-#define USB_CH_IP_CUR_LVL_1P1		1100
-#define USB_CH_IP_CUR_LVL_1P3		1300
-#define USB_CH_IP_CUR_LVL_1P4		1400
-#define USB_CH_IP_CUR_LVL_1P5		1500
+/* VBUS input current limits supported in AB8500 in uA */
+#define USB_CH_IP_CUR_LVL_0P05		50000
+#define USB_CH_IP_CUR_LVL_0P09		98000
+#define USB_CH_IP_CUR_LVL_0P19		193000
+#define USB_CH_IP_CUR_LVL_0P29		290000
+#define USB_CH_IP_CUR_LVL_0P38		380000
+#define USB_CH_IP_CUR_LVL_0P45		450000
+#define USB_CH_IP_CUR_LVL_0P5		500000
+#define USB_CH_IP_CUR_LVL_0P6		600000
+#define USB_CH_IP_CUR_LVL_0P7		700000
+#define USB_CH_IP_CUR_LVL_0P8		800000
+#define USB_CH_IP_CUR_LVL_0P9		900000
+#define USB_CH_IP_CUR_LVL_1P0		1000000
+#define USB_CH_IP_CUR_LVL_1P1		1100000
+#define USB_CH_IP_CUR_LVL_1P3		1300000
+#define USB_CH_IP_CUR_LVL_1P4		1400000
+#define USB_CH_IP_CUR_LVL_1P5		1500000
 
 #define VBAT_TRESH_IP_CUR_RED		3800
 
@@ -186,7 +186,7 @@ struct ab8500_charger_info {
 	int charger_voltage;
 	int cv_active;
 	bool wd_expired;
-	int charger_current;
+	int charger_current_ua;
 };
 
 struct ab8500_charger_event_flags {
@@ -201,17 +201,17 @@ struct ab8500_charger_event_flags {
 };
 
 struct ab8500_charger_usb_state {
-	int usb_current;
-	int usb_current_tmp;
+	int usb_current_ua;
+	int usb_current_tmp_ua;
 	enum ab8500_usb_state state;
 	enum ab8500_usb_state state_tmp;
 	spinlock_t usb_lock;
 };
 
 struct ab8500_charger_max_usb_in_curr {
-	int usb_type_max;
-	int set_max;
-	int calculated_max;
+	int usb_type_max_ua;
+	int set_max_ua;
+	int calculated_max_ua;
 };
 
 /**
@@ -552,7 +552,7 @@ static int ab8500_charger_get_vbus_voltage(struct ab8500_charger *di)
  * @di:		pointer to the ab8500_charger structure
  *
  * This function returns the usb charger current.
- * Returns usb current (on success) and error code on failure
+ * Returns usb current in microamperes (on success) and error code on failure
  */
 static int ab8500_charger_get_usb_current(struct ab8500_charger *di)
 {
@@ -566,7 +566,8 @@ static int ab8500_charger_get_usb_current(struct ab8500_charger *di)
 	} else {
 		ich = 0;
 	}
-	return ich;
+	/* Return microamperes */
+	return ich * 1000;
 }
 
 /**
@@ -574,7 +575,7 @@ static int ab8500_charger_get_usb_current(struct ab8500_charger *di)
  * @di:		pointer to the ab8500_charger structure
  *
  * This function returns the ac charger current.
- * Returns ac current (on success) and error code on failure.
+ * Returns ac current in microamperes (on success) and error code on failure.
  */
 static int ab8500_charger_get_ac_current(struct ab8500_charger *di)
 {
@@ -588,7 +589,8 @@ static int ab8500_charger_get_ac_current(struct ab8500_charger *di)
 	} else {
 		ich = 0;
 	}
-	return ich;
+	/* Return microamperes */
+	return ich * 1000;
 }
 
 /**
@@ -711,19 +713,19 @@ static int ab8500_charger_max_usb_curr(struct ab8500_charger *di,
 	case USB_STAT_STD_HOST_C_S:
 		dev_dbg(di->dev, "USB Type - Standard host is "
 			"detected through USB driver\n");
-		di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P5;
+		di->max_usb_in_curr.usb_type_max_ua = USB_CH_IP_CUR_LVL_0P5;
 		di->is_aca_rid = 0;
 		break;
 	case USB_STAT_HOST_CHG_HS_CHIRP:
-		di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P5;
+		di->max_usb_in_curr.usb_type_max_ua = USB_CH_IP_CUR_LVL_0P5;
 		di->is_aca_rid = 0;
 		break;
 	case USB_STAT_HOST_CHG_HS:
-		di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P5;
+		di->max_usb_in_curr.usb_type_max_ua = USB_CH_IP_CUR_LVL_0P5;
 		di->is_aca_rid = 0;
 		break;
 	case USB_STAT_ACA_RID_C_HS:
-		di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P9;
+		di->max_usb_in_curr.usb_type_max_ua = USB_CH_IP_CUR_LVL_0P9;
 		di->is_aca_rid = 0;
 		break;
 	case USB_STAT_ACA_RID_A:
@@ -732,7 +734,7 @@ static int ab8500_charger_max_usb_curr(struct ab8500_charger *di,
 		 * can consume (900mA). Closest level is 500mA
 		 */
 		dev_dbg(di->dev, "USB_STAT_ACA_RID_A detected\n");
-		di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P5;
+		di->max_usb_in_curr.usb_type_max_ua = USB_CH_IP_CUR_LVL_0P5;
 		di->is_aca_rid = 1;
 		break;
 	case USB_STAT_ACA_RID_B:
@@ -740,36 +742,36 @@ static int ab8500_charger_max_usb_curr(struct ab8500_charger *di,
 		 * Dedicated charger level minus 120mA (20mA for ACA and
 		 * 100mA for potential accessory). Closest level is 1300mA
 		 */
-		di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_1P3;
+		di->max_usb_in_curr.usb_type_max_ua = USB_CH_IP_CUR_LVL_1P3;
 		dev_dbg(di->dev, "USB Type - 0x%02x MaxCurr: %d", link_status,
-				di->max_usb_in_curr.usb_type_max);
+				di->max_usb_in_curr.usb_type_max_ua);
 		di->is_aca_rid = 1;
 		break;
 	case USB_STAT_HOST_CHG_NM:
-		di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P5;
+		di->max_usb_in_curr.usb_type_max_ua = USB_CH_IP_CUR_LVL_0P5;
 		di->is_aca_rid = 0;
 		break;
 	case USB_STAT_DEDICATED_CHG:
-		di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_1P5;
+		di->max_usb_in_curr.usb_type_max_ua = USB_CH_IP_CUR_LVL_1P5;
 		di->is_aca_rid = 0;
 		break;
 	case USB_STAT_ACA_RID_C_HS_CHIRP:
 	case USB_STAT_ACA_RID_C_NM:
-		di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_1P5;
+		di->max_usb_in_curr.usb_type_max_ua = USB_CH_IP_CUR_LVL_1P5;
 		di->is_aca_rid = 1;
 		break;
 	case USB_STAT_NOT_CONFIGURED:
 		if (di->vbus_detected) {
 			di->usb_device_is_unrecognised = true;
 			dev_dbg(di->dev, "USB Type - Legacy charger.\n");
-			di->max_usb_in_curr.usb_type_max =
+			di->max_usb_in_curr.usb_type_max_ua =
 						USB_CH_IP_CUR_LVL_1P5;
 			break;
 		}
 		fallthrough;
 	case USB_STAT_HM_IDGND:
 		dev_err(di->dev, "USB Type - Charging not allowed\n");
-		di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P05;
+		di->max_usb_in_curr.usb_type_max_ua = USB_CH_IP_CUR_LVL_0P05;
 		ret = -ENXIO;
 		break;
 	case USB_STAT_RESERVED:
@@ -781,11 +783,11 @@ static int ab8500_charger_max_usb_curr(struct ab8500_charger *di,
 			break;
 		} else {
 			dev_dbg(di->dev, "USB Type - Charging not allowed\n");
-			di->max_usb_in_curr.usb_type_max =
+			di->max_usb_in_curr.usb_type_max_ua =
 						USB_CH_IP_CUR_LVL_0P05;
 			dev_dbg(di->dev, "USB Type - 0x%02x MaxCurr: %d",
 				link_status,
-				di->max_usb_in_curr.usb_type_max);
+				di->max_usb_in_curr.usb_type_max_ua);
 			ret = -ENXIO;
 			break;
 		}
@@ -793,25 +795,25 @@ static int ab8500_charger_max_usb_curr(struct ab8500_charger *di,
 	case USB_STAT_CARKIT_2:
 	case USB_STAT_ACA_DOCK_CHARGER:
 	case USB_STAT_CHARGER_LINE_1:
-		di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P5;
+		di->max_usb_in_curr.usb_type_max_ua = USB_CH_IP_CUR_LVL_0P5;
 		dev_dbg(di->dev, "USB Type - 0x%02x MaxCurr: %d", link_status,
-				di->max_usb_in_curr.usb_type_max);
+				di->max_usb_in_curr.usb_type_max_ua);
 		break;
 	case USB_STAT_NOT_VALID_LINK:
 		dev_err(di->dev, "USB Type invalid - try charging anyway\n");
-		di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P5;
+		di->max_usb_in_curr.usb_type_max_ua = USB_CH_IP_CUR_LVL_0P5;
 		break;
 
 	default:
 		dev_err(di->dev, "USB Type - Unknown\n");
-		di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P05;
+		di->max_usb_in_curr.usb_type_max_ua = USB_CH_IP_CUR_LVL_0P05;
 		ret = -ENXIO;
 		break;
 	}
 
-	di->max_usb_in_curr.set_max = di->max_usb_in_curr.usb_type_max;
+	di->max_usb_in_curr.set_max_ua = di->max_usb_in_curr.usb_type_max_ua;
 	dev_dbg(di->dev, "USB Type - 0x%02x MaxCurr: %d",
-		link_status, di->max_usb_in_curr.set_max);
+		link_status, di->max_usb_in_curr.set_max_ua);
 
 	return ret;
 }
@@ -1027,51 +1029,51 @@ static int ab8500_voltage_to_regval(int voltage)
 
 /* This array maps the raw register value to charger input current */
 static int ab8500_charge_input_curr_map[] = {
-	50, 98, 193, 290, 380, 450, 500, 600,
-	700, 800, 900, 1000, 1100, 1300, 1400, 1500,
+	50000, 98000, 193000, 290000, 380000, 450000, 500000, 600000,
+	700000, 800000, 900000, 1000000, 1100000, 1300000, 1400000, 1500000,
 };
 
 /* This array maps the raw register value to charger output current */
 static int ab8500_charge_output_curr_map[] = {
-	100, 200, 300, 400, 500, 600, 700, 800,
-	900, 1000, 1100, 1200, 1300, 1400, 1500, 1500,
+	100000, 200000, 300000, 400000, 500000, 600000, 700000, 800000,
+	900000, 1000000, 1100000, 1200000, 1300000, 1400000, 1500000, 1500000,
 };
 
-static int ab8500_current_to_regval(struct ab8500_charger *di, int curr)
+static int ab8500_current_to_regval(struct ab8500_charger *di, int curr_ua)
 {
 	int i;
 
-	if (curr < ab8500_charge_output_curr_map[0])
+	if (curr_ua < ab8500_charge_output_curr_map[0])
 		return 0;
 
 	for (i = 0; i < ARRAY_SIZE(ab8500_charge_output_curr_map); i++) {
-		if (curr < ab8500_charge_output_curr_map[i])
+		if (curr_ua < ab8500_charge_output_curr_map[i])
 			return i - 1;
 	}
 
 	/* If not last element, return error */
 	i =  ARRAY_SIZE(ab8500_charge_output_curr_map) - 1;
-	if (curr == ab8500_charge_output_curr_map[i])
+	if (curr_ua == ab8500_charge_output_curr_map[i])
 		return i;
 	else
 		return -1;
 }
 
-static int ab8500_vbus_in_curr_to_regval(struct ab8500_charger *di, int curr)
+static int ab8500_vbus_in_curr_to_regval(struct ab8500_charger *di, int curr_ua)
 {
 	int i;
 
-	if (curr < ab8500_charge_input_curr_map[0])
+	if (curr_ua < ab8500_charge_input_curr_map[0])
 		return 0;
 
 	for (i = 0; i < ARRAY_SIZE(ab8500_charge_input_curr_map); i++) {
-		if (curr < ab8500_charge_input_curr_map[i])
+		if (curr_ua < ab8500_charge_input_curr_map[i])
 			return i - 1;
 	}
 
 	/* If not last element, return error */
 	i =  ARRAY_SIZE(ab8500_charge_input_curr_map) - 1;
-	if (curr == ab8500_charge_input_curr_map[i])
+	if (curr_ua == ab8500_charge_input_curr_map[i])
 		return i;
 	else
 		return -1;
@@ -1082,35 +1084,35 @@ static int ab8500_vbus_in_curr_to_regval(struct ab8500_charger *di, int curr)
  * @di:		pointer to the ab8500_charger structre
  *
  * The usb stack provides the maximum current that can be drawn from
- * the standard usb host. This will be in mA.
- * This function converts current in mA to a value that can be written
+ * the standard usb host. This will be in uA.
+ * This function converts current in uA to a value that can be written
  * to the register. Returns -1 if charging is not allowed
  */
 static int ab8500_charger_get_usb_cur(struct ab8500_charger *di)
 {
 	int ret = 0;
-	switch (di->usb_state.usb_current) {
-	case 100:
-		di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P09;
+	switch (di->usb_state.usb_current_ua) {
+	case 100000:
+		di->max_usb_in_curr.usb_type_max_ua = USB_CH_IP_CUR_LVL_0P09;
 		break;
-	case 200:
-		di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P19;
+	case 200000:
+		di->max_usb_in_curr.usb_type_max_ua = USB_CH_IP_CUR_LVL_0P19;
 		break;
-	case 300:
-		di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P29;
+	case 300000:
+		di->max_usb_in_curr.usb_type_max_ua = USB_CH_IP_CUR_LVL_0P29;
 		break;
-	case 400:
-		di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P38;
+	case 400000:
+		di->max_usb_in_curr.usb_type_max_ua = USB_CH_IP_CUR_LVL_0P38;
 		break;
-	case 500:
-		di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P5;
+	case 500000:
+		di->max_usb_in_curr.usb_type_max_ua = USB_CH_IP_CUR_LVL_0P5;
 		break;
 	default:
-		di->max_usb_in_curr.usb_type_max = USB_CH_IP_CUR_LVL_0P05;
+		di->max_usb_in_curr.usb_type_max_ua = USB_CH_IP_CUR_LVL_0P05;
 		ret = -EPERM;
 		break;
 	}
-	di->max_usb_in_curr.set_max = di->max_usb_in_curr.usb_type_max;
+	di->max_usb_in_curr.set_max_ua = di->max_usb_in_curr.usb_type_max_ua;
 	return ret;
 }
 
@@ -1135,7 +1137,7 @@ static bool ab8500_charger_check_continue_stepping(struct ab8500_charger *di,
 /**
  * ab8500_charger_set_current() - set charger current
  * @di:		pointer to the ab8500_charger structure
- * @ich:	charger current, in mA
+ * @ich_ua:	charger current, in uA
  * @reg:	select what charger register to set
  *
  * Set charger current.
@@ -1146,7 +1148,7 @@ static bool ab8500_charger_check_continue_stepping(struct ab8500_charger *di,
  * Returns error code in case of failure else 0(on success)
  */
 static int ab8500_charger_set_current(struct ab8500_charger *di,
-	int ich, int reg)
+	int ich_ua, int reg)
 {
 	int ret = 0;
 	int curr_index, prev_curr_index, shift_value, i;
@@ -1167,7 +1169,7 @@ static int ab8500_charger_set_current(struct ab8500_charger *di,
 	case AB8500_MCH_IPT_CURLVL_REG:
 		shift_value = MAIN_CH_INPUT_CURR_SHIFT;
 		prev_curr_index = (reg_value >> shift_value);
-		curr_index = ab8500_current_to_regval(di, ich);
+		curr_index = ab8500_current_to_regval(di, ich_ua);
 		step_udelay = STEP_UDELAY;
 		if (!di->ac.charger_connected)
 			no_stepping = true;
@@ -1175,7 +1177,7 @@ static int ab8500_charger_set_current(struct ab8500_charger *di,
 	case AB8500_USBCH_IPT_CRNTLVL_REG:
 		shift_value = VBUS_IN_CURR_LIM_SHIFT;
 		prev_curr_index = (reg_value >> shift_value);
-		curr_index = ab8500_vbus_in_curr_to_regval(di, ich);
+		curr_index = ab8500_vbus_in_curr_to_regval(di, ich_ua);
 		step_udelay = STEP_UDELAY * 100;
 
 		if (!di->usb.charger_connected)
@@ -1184,7 +1186,7 @@ static int ab8500_charger_set_current(struct ab8500_charger *di,
 	case AB8500_CH_OPT_CRNTLVL_REG:
 		shift_value = 0;
 		prev_curr_index = (reg_value >> shift_value);
-		curr_index = ab8500_current_to_regval(di, ich);
+		curr_index = ab8500_current_to_regval(di, ich_ua);
 		step_udelay = STEP_UDELAY;
 		if (curr_index && (curr_index - prev_curr_index) > 1)
 			step_udelay *= 100;
@@ -1213,8 +1215,8 @@ static int ab8500_charger_set_current(struct ab8500_charger *di,
 		goto exit_set_current;
 	}
 
-	dev_dbg(di->dev, "%s set charger current: %d mA for reg: 0x%02x\n",
-		__func__, ich, reg);
+	dev_dbg(di->dev, "%s set charger current: %d uA for reg: 0x%02x\n",
+		__func__, ich_ua, reg);
 
 	if (no_stepping) {
 		ret = abx500_set_register_interruptible(di->dev, AB8500_CHARGER,
@@ -1261,31 +1263,31 @@ exit_set_current:
 /**
  * ab8500_charger_set_vbus_in_curr() - set VBUS input current limit
  * @di:		pointer to the ab8500_charger structure
- * @ich_in:	charger input current limit
+ * @ich_in_ua:	charger input current limit in microampere
  *
  * Sets the current that can be drawn from the USB host
  * Returns error code in case of failure else 0(on success)
  */
 static int ab8500_charger_set_vbus_in_curr(struct ab8500_charger *di,
-		int ich_in)
+		int ich_in_ua)
 {
 	int min_value;
 	int ret;
 
 	/* We should always use to lowest current limit */
-	min_value = min(di->bm->chg_params->usb_curr_max, ich_in);
-	if (di->max_usb_in_curr.set_max > 0)
-		min_value = min(di->max_usb_in_curr.set_max, min_value);
+	min_value = min(di->bm->chg_params->usb_curr_max_ua, ich_in_ua);
+	if (di->max_usb_in_curr.set_max_ua > 0)
+		min_value = min(di->max_usb_in_curr.set_max_ua, min_value);
 
-	if (di->usb_state.usb_current >= 0)
-		min_value = min(di->usb_state.usb_current, min_value);
+	if (di->usb_state.usb_current_ua >= 0)
+		min_value = min(di->usb_state.usb_current_ua, min_value);
 
 	switch (min_value) {
-	case 100:
+	case 100000:
 		if (di->vbat < VBAT_TRESH_IP_CUR_RED)
 			min_value = USB_CH_IP_CUR_LVL_0P05;
 		break;
-	case 500:
+	case 500000:
 		if (di->vbat < VBAT_TRESH_IP_CUR_RED)
 			min_value = USB_CH_IP_CUR_LVL_0P45;
 		break;
@@ -1293,7 +1295,7 @@ static int ab8500_charger_set_vbus_in_curr(struct ab8500_charger *di,
 		break;
 	}
 
-	dev_info(di->dev, "VBUS input current limit set to %d mA\n", min_value);
+	dev_info(di->dev, "VBUS input current limit set to %d uA\n", min_value);
 
 	mutex_lock(&di->usb_ipt_crnt_lock);
 	ret = ab8500_charger_set_current(di, min_value,
@@ -1306,30 +1308,30 @@ static int ab8500_charger_set_vbus_in_curr(struct ab8500_charger *di,
 /**
  * ab8500_charger_set_main_in_curr() - set main charger input current
  * @di:		pointer to the ab8500_charger structure
- * @ich_in:	input charger current, in mA
+ * @ich_in_ua:	input charger current, in uA
  *
  * Set main charger input current.
  * Returns error code in case of failure else 0(on success)
  */
 static int ab8500_charger_set_main_in_curr(struct ab8500_charger *di,
-	int ich_in)
+	int ich_in_ua)
 {
-	return ab8500_charger_set_current(di, ich_in,
+	return ab8500_charger_set_current(di, ich_in_ua,
 		AB8500_MCH_IPT_CURLVL_REG);
 }
 
 /**
  * ab8500_charger_set_output_curr() - set charger output current
  * @di:		pointer to the ab8500_charger structure
- * @ich_out:	output charger current, in mA
+ * @ich_out_ua:	output charger current, in uA
  *
  * Set charger output current.
  * Returns error code in case of failure else 0(on success)
  */
 static int ab8500_charger_set_output_curr(struct ab8500_charger *di,
-	int ich_out)
+	int ich_out_ua)
 {
-	return ab8500_charger_set_current(di, ich_out,
+	return ab8500_charger_set_current(di, ich_out_ua,
 		AB8500_CH_OPT_CRNTLVL_REG);
 }
 
@@ -1381,13 +1383,13 @@ static int ab8500_charger_led_en(struct ab8500_charger *di, int on)
  * @di:		pointer to the ab8500_charger structure
  * @enable:	enable/disable flag
  * @vset:	charging voltage
- * @iset:	charging current
+ * @iset_ua:	charging current in microampere
  *
  * Enable/Disable AC/Mains charging and turns on/off the charging led
  * respectively.
  **/
 static int ab8500_charger_ac_en(struct ux500_charger *charger,
-	int enable, int vset, int iset)
+	int enable, int vset, int iset_ua)
 {
 	int ret;
 	int volt_index;
@@ -1405,7 +1407,7 @@ static int ab8500_charger_ac_en(struct ux500_charger *charger,
 		}
 
 		/* Enable AC charging */
-		dev_dbg(di->dev, "Enable AC: %dmV %dmA\n", vset, iset);
+		dev_dbg(di->dev, "Enable AC: %dmV %duA\n", vset, iset_ua);
 
 		/*
 		 * Due to a bug in AB8500, BTEMP_HIGH/LOW interrupts
@@ -1428,9 +1430,9 @@ static int ab8500_charger_ac_en(struct ux500_charger *charger,
 
 		/* Check if the requested voltage or current is valid */
 		volt_index = ab8500_voltage_to_regval(vset);
-		curr_index = ab8500_current_to_regval(di, iset);
+		curr_index = ab8500_current_to_regval(di, iset_ua);
 		input_curr_index = ab8500_current_to_regval(di,
-			di->bm->chg_params->ac_curr_max);
+			di->bm->chg_params->ac_curr_max_ua);
 		if (volt_index < 0 || curr_index < 0 || input_curr_index < 0) {
 			dev_err(di->dev,
 				"Charger voltage or current too high, "
@@ -1447,14 +1449,14 @@ static int ab8500_charger_ac_en(struct ux500_charger *charger,
 		}
 		/* MainChInputCurr: current that can be drawn from the charger*/
 		ret = ab8500_charger_set_main_in_curr(di,
-			di->bm->chg_params->ac_curr_max);
+			di->bm->chg_params->ac_curr_max_ua);
 		if (ret) {
 			dev_err(di->dev, "%s Failed to set MainChInputCurr\n",
 				__func__);
 			return ret;
 		}
 		/* ChOutputCurentLevel: protected output current */
-		ret = ab8500_charger_set_output_curr(di, iset);
+		ret = ab8500_charger_set_output_curr(di, iset_ua);
 		if (ret) {
 			dev_err(di->dev, "%s "
 				"Failed to set ChOutputCurentLevel\n",
@@ -1558,13 +1560,13 @@ static int ab8500_charger_ac_en(struct ux500_charger *charger,
  * @di:		pointer to the ab8500_charger structure
  * @enable:	enable/disable flag
  * @vset:	charging voltage
- * @ich_out:	charger output current
+ * @ich_out_ua:	charger output current in microampere
  *
  * Enable/Disable USB charging and turns on/off the charging led respectively.
  * Returns error code in case of failure else 0(on success)
  */
 static int ab8500_charger_usb_en(struct ux500_charger *charger,
-	int enable, int vset, int ich_out)
+	int enable, int vset, int ich_out_ua)
 {
 	int ret;
 	int volt_index;
@@ -1600,11 +1602,11 @@ static int ab8500_charger_usb_en(struct ux500_charger *charger,
 		}
 
 		/* Enable USB charging */
-		dev_dbg(di->dev, "Enable USB: %dmV %dmA\n", vset, ich_out);
+		dev_dbg(di->dev, "Enable USB: %d mV %d uA\n", vset, ich_out_ua);
 
 		/* Check if the requested voltage or current is valid */
 		volt_index = ab8500_voltage_to_regval(vset);
-		curr_index = ab8500_current_to_regval(di, ich_out);
+		curr_index = ab8500_current_to_regval(di, ich_out_ua);
 		if (volt_index < 0 || curr_index < 0) {
 			dev_err(di->dev,
 				"Charger voltage or current too high, "
@@ -1645,14 +1647,14 @@ static int ab8500_charger_usb_en(struct ux500_charger *charger,
 
 		/* USBChInputCurr: current that can be drawn from the usb */
 		ret = ab8500_charger_set_vbus_in_curr(di,
-					di->max_usb_in_curr.usb_type_max);
+					di->max_usb_in_curr.usb_type_max_ua);
 		if (ret) {
 			dev_err(di->dev, "setting USBChInputCurr failed\n");
 			return ret;
 		}
 
 		/* ChOutputCurentLevel: protected output current */
-		ret = ab8500_charger_set_output_curr(di, ich_out);
+		ret = ab8500_charger_set_output_curr(di, ich_out_ua);
 		if (ret) {
 			dev_err(di->dev, "%s "
 				"Failed to set ChOutputCurentLevel\n",
@@ -1739,13 +1741,13 @@ out:
  * ab8500_charger_usb_check_enable() - enable usb charging
  * @charger:	pointer to the ux500_charger structure
  * @vset:	charging voltage
- * @iset:	charger output current
+ * @iset_ua:	charger output current in microampere
  *
  * Check if the VBUS charger has been disconnected and reconnected without
  * AB8500 rising an interrupt. Returns 0 on success.
  */
 static int ab8500_charger_usb_check_enable(struct ux500_charger *charger,
-	int vset, int iset)
+	int vset, int iset_ua)
 {
 	u8 usbch_ctrl1 = 0;
 	int ret = 0;
@@ -1774,7 +1776,7 @@ static int ab8500_charger_usb_check_enable(struct ux500_charger *charger,
 			return ret;
 		}
 
-		ret = ab8500_charger_usb_en(&di->usb_chg, true, vset, iset);
+		ret = ab8500_charger_usb_en(&di->usb_chg, true, vset, iset_ua);
 		if (ret < 0) {
 			dev_err(di->dev, "Failed to enable VBUS charger %d\n",
 					__LINE__);
@@ -1788,13 +1790,13 @@ static int ab8500_charger_usb_check_enable(struct ux500_charger *charger,
  * ab8500_charger_ac_check_enable() - enable usb charging
  * @charger:	pointer to the ux500_charger structure
  * @vset:	charging voltage
- * @iset:	charger output current
+ * @iset_ua:	charger output current in micrompere
  *
  * Check if the AC charger has been disconnected and reconnected without
  * AB8500 rising an interrupt. Returns 0 on success.
  */
 static int ab8500_charger_ac_check_enable(struct ux500_charger *charger,
-	int vset, int iset)
+	int vset, int iset_ua)
 {
 	u8 mainch_ctrl1 = 0;
 	int ret = 0;
@@ -1824,7 +1826,7 @@ static int ab8500_charger_ac_check_enable(struct ux500_charger *charger,
 			return ret;
 		}
 
-		ret = ab8500_charger_ac_en(&di->usb_chg, true, vset, iset);
+		ret = ab8500_charger_ac_en(&di->usb_chg, true, vset, iset_ua);
 		if (ret < 0) {
 			dev_err(di->dev, "failed to enable AC charger %d\n",
 				__LINE__);
@@ -1863,13 +1865,14 @@ static int ab8500_charger_watchdog_kick(struct ux500_charger *charger)
 
 /**
  * ab8500_charger_update_charger_current() - update charger current
- * @di:		pointer to the ab8500_charger structure
+ * @charger:		pointer to the ab8500_charger structure
+ * @ich_out_ua:		desired output current in microampere
  *
  * Update the charger output current for the specified charger
  * Returns error code in case of failure else 0(on success)
  */
 static int ab8500_charger_update_charger_current(struct ux500_charger *charger,
-		int ich_out)
+		int ich_out_ua)
 {
 	int ret;
 	struct ab8500_charger *di;
@@ -1881,7 +1884,7 @@ static int ab8500_charger_update_charger_current(struct ux500_charger *charger,
 	else
 		return -ENXIO;
 
-	ret = ab8500_charger_set_output_curr(di, ich_out);
+	ret = ab8500_charger_set_output_curr(di, ich_out_ua);
 	if (ret) {
 		dev_err(di->dev, "%s "
 			"Failed to set ChOutputCurentLevel\n",
@@ -1973,10 +1976,10 @@ static void ab8500_charger_check_vbat_work(struct work_struct *work)
 		di->vbat > VBAT_TRESH_IP_CUR_RED))) {
 
 		dev_dbg(di->dev, "Vbat did cross threshold, curr: %d, new: %d,"
-			" old: %d\n", di->max_usb_in_curr.usb_type_max,
+			" old: %d\n", di->max_usb_in_curr.usb_type_max_ua,
 			di->vbat, di->old_vbat);
 		ab8500_charger_set_vbus_in_curr(di,
-					di->max_usb_in_curr.usb_type_max);
+					di->max_usb_in_curr.usb_type_max_ua);
 		power_supply_changed(di->usb_chg.psy);
 	}
 
@@ -2257,7 +2260,7 @@ static void ab8500_charger_usb_link_attach_work(struct work_struct *work)
 	/* Update maximum input current if USB enumeration is not detected */
 	if (!di->usb.charger_online) {
 		ret = ab8500_charger_set_vbus_in_curr(di,
-					di->max_usb_in_curr.usb_type_max);
+					di->max_usb_in_curr.usb_type_max_ua);
 		if (ret)
 			return;
 	}
@@ -2419,11 +2422,11 @@ static void ab8500_charger_usb_state_changed_work(struct work_struct *work)
 
 	spin_lock_irqsave(&di->usb_state.usb_lock, flags);
 	di->usb_state.state = di->usb_state.state_tmp;
-	di->usb_state.usb_current = di->usb_state.usb_current_tmp;
+	di->usb_state.usb_current_ua = di->usb_state.usb_current_tmp_ua;
 	spin_unlock_irqrestore(&di->usb_state.usb_lock, flags);
 
-	dev_dbg(di->dev, "%s USB state: 0x%02x mA: %d\n",
-		__func__, di->usb_state.state, di->usb_state.usb_current);
+	dev_dbg(di->dev, "%s USB state: 0x%02x uA: %d\n",
+		__func__, di->usb_state.state, di->usb_state.usb_current_ua);
 
 	switch (di->usb_state.state) {
 	case AB8500_BM_USB_STATE_RESET_HS:
@@ -2449,7 +2452,7 @@ static void ab8500_charger_usb_state_changed_work(struct work_struct *work)
 		if (!ab8500_charger_get_usb_cur(di)) {
 			/* Update maximum input current */
 			ret = ab8500_charger_set_vbus_in_curr(di,
-					di->max_usb_in_curr.usb_type_max);
+					di->max_usb_in_curr.usb_type_max_ua);
 			if (ret)
 				return;
 
@@ -2669,7 +2672,7 @@ static void ab8500_charger_vbus_drop_end_work(struct work_struct *work)
 {
 	struct ab8500_charger *di = container_of(work,
 		struct ab8500_charger, vbus_drop_end_work.work);
-	int ret, curr;
+	int ret, curr_ua;
 	u8 reg_value;
 
 	di->flags.vbus_drop_end = false;
@@ -2685,30 +2688,30 @@ static void ab8500_charger_vbus_drop_end_work(struct work_struct *work)
 		return;
 	}
 
-	curr = ab8500_charge_input_curr_map[
+	curr_ua = ab8500_charge_input_curr_map[
 		reg_value >> AUTO_VBUS_IN_CURR_LIM_SHIFT];
 
-	if (di->max_usb_in_curr.calculated_max != curr) {
+	if (di->max_usb_in_curr.calculated_max_ua != curr_ua) {
 		/* USB source is collapsing */
-		di->max_usb_in_curr.calculated_max = curr;
+		di->max_usb_in_curr.calculated_max_ua = curr_ua;
 		dev_dbg(di->dev,
-			 "VBUS input current limiting to %d mA\n",
-			 di->max_usb_in_curr.calculated_max);
+			 "VBUS input current limiting to %d uA\n",
+			 di->max_usb_in_curr.calculated_max_ua);
 	} else {
 		/*
 		 * USB source can not give more than this amount.
 		 * Taking more will collapse the source.
 		 */
-		di->max_usb_in_curr.set_max =
-			di->max_usb_in_curr.calculated_max;
+		di->max_usb_in_curr.set_max_ua =
+			di->max_usb_in_curr.calculated_max_ua;
 		dev_dbg(di->dev,
-			 "VBUS input current limited to %d mA\n",
-			 di->max_usb_in_curr.set_max);
+			 "VBUS input current limited to %d uA\n",
+			 di->max_usb_in_curr.set_max_ua);
 	}
 
 	if (di->usb.charger_connected)
 		ab8500_charger_set_vbus_in_curr(di,
-					di->max_usb_in_curr.usb_type_max);
+					di->max_usb_in_curr.usb_type_max_ua);
 }
 
 /**
@@ -2953,8 +2956,8 @@ static int ab8500_charger_ac_get_property(struct power_supply *psy,
 	case POWER_SUPPLY_PROP_CURRENT_NOW:
 		ret = ab8500_charger_get_ac_current(di);
 		if (ret >= 0)
-			di->ac.charger_current = ret;
-		val->intval = di->ac.charger_current * 1000;
+			di->ac.charger_current_ua = ret;
+		val->intval = di->ac.charger_current_ua;
 		break;
 	default:
 		return -EINVAL;
@@ -3021,8 +3024,8 @@ static int ab8500_charger_usb_get_property(struct power_supply *psy,
 	case POWER_SUPPLY_PROP_CURRENT_NOW:
 		ret = ab8500_charger_get_usb_current(di);
 		if (ret >= 0)
-			di->usb.charger_current = ret;
-		val->intval = di->usb.charger_current * 1000;
+			di->usb.charger_current_ua = ret;
+		val->intval = di->usb.charger_current_ua;
 		break;
 	case POWER_SUPPLY_PROP_CURRENT_AVG:
 		/*
@@ -3198,6 +3201,11 @@ static int ab8500_charger_usb_notifier_call(struct notifier_block *nb,
 	struct ab8500_charger *di =
 		container_of(nb, struct ab8500_charger, nb);
 	enum ab8500_usb_state bm_usb_state;
+	/*
+	 * FIXME: it appears the AB8500 PHY never sends what it should here.
+	 * Fix the PHY driver to properly notify the desired current.
+	 * Also broadcast microampere and not milliampere.
+	 */
 	unsigned mA = *((unsigned *)power);
 
 	if (event != USB_EVENT_VBUS) {
@@ -3208,7 +3216,7 @@ static int ab8500_charger_usb_notifier_call(struct notifier_block *nb,
 	/* TODO: State is fabricate  here. See if charger really needs USB
 	 * state or if mA is enough
 	 */
-	if ((di->usb_state.usb_current == 2) && (mA > 2))
+	if ((di->usb_state.usb_current_ua == 2000) && (mA > 2))
 		bm_usb_state = AB8500_BM_USB_STATE_RESUME;
 	else if (mA == 0)
 		bm_usb_state = AB8500_BM_USB_STATE_RESET_HS;
@@ -3224,7 +3232,8 @@ static int ab8500_charger_usb_notifier_call(struct notifier_block *nb,
 
 	spin_lock(&di->usb_state.usb_lock);
 	di->usb_state.state_tmp = bm_usb_state;
-	di->usb_state.usb_current_tmp = mA;
+	/* FIXME: broadcast ua instead, see above */
+	di->usb_state.usb_current_tmp_ua = mA * 1000;
 	spin_unlock(&di->usb_state.usb_lock);
 
 	/*
@@ -3514,7 +3523,7 @@ static int ab8500_charger_probe(struct platform_device *pdev)
 	di->ac_chg.ops.update_curr = &ab8500_charger_update_charger_current;
 	di->ac_chg.max_out_volt = ab8500_charger_voltage_map[
 		ARRAY_SIZE(ab8500_charger_voltage_map) - 1];
-	di->ac_chg.max_out_curr =
+	di->ac_chg.max_out_curr_ua =
 		ab8500_charge_output_curr_map[ARRAY_SIZE(ab8500_charge_output_curr_map) - 1];
 	di->ac_chg.wdt_refresh = CHG_WD_INTERVAL;
 	/*
@@ -3535,11 +3544,11 @@ static int ab8500_charger_probe(struct platform_device *pdev)
 	di->usb_chg.ops.update_curr = &ab8500_charger_update_charger_current;
 	di->usb_chg.max_out_volt = ab8500_charger_voltage_map[
 		ARRAY_SIZE(ab8500_charger_voltage_map) - 1];
-	di->usb_chg.max_out_curr =
+	di->usb_chg.max_out_curr_ua =
 		ab8500_charge_output_curr_map[ARRAY_SIZE(ab8500_charge_output_curr_map) - 1];
 	di->usb_chg.wdt_refresh = CHG_WD_INTERVAL;
 	di->usb_chg.external = false;
-	di->usb_state.usb_current = -1;
+	di->usb_state.usb_current_ua = -1;
 
 	mutex_init(&di->charger_attached_mutex);