Merge branch 'highbank/soc' into next/soc

Conflicts:
	arch/arm/mach-mxs/include/mach/gpio.h
	arch/arm/mach-omap2/board-generic.c
	arch/arm/plat-mxc/include/mach/gpio.h

Documentation/devicetree/bindings/arm/calxeda.txt

@@ -0,0 +1,8 @@
+Calxeda Highbank Platforms Device Tree Bindings
+-----------------------------------------------
+
+Boards with Calxeda Cortex-A9 based Highbank SOC shall have the following
+properties.
+
+Required root node properties:
+    - compatible = "calxeda,highbank";

Documentation/devicetree/bindings/arm/l2cc.txt

@@ -0,0 +1,44 @@
+* ARM L2 Cache Controller
+
+ARM cores often have a separate level 2 cache controller. There are various
+implementations of the L2 cache controller with compatible programming models.
+The ARM L2 cache representation in the device tree should be done as follows:
+
+Required properties:
+
+- compatible : should be one of:
+	"arm,pl310-cache"
+	"arm,l220-cache"
+	"arm,l210-cache"
+- cache-unified : Specifies the cache is a unified cache.
+- cache-level : Should be set to 2 for a level 2 cache.
+- reg : Physical base address and size of cache controller's memory mapped
+  registers.
+
+Optional properties:
+
+- arm,data-latency : Cycles of latency for Data RAM accesses. Specifies 3 cells of
+  read, write and setup latencies. Minimum valid values are 1. Controllers
+  without setup latency control should use a value of 0.
+- arm,tag-latency : Cycles of latency for Tag RAM accesses. Specifies 3 cells of
+  read, write and setup latencies. Controllers without setup latency control
+  should use 0. Controllers without separate read and write Tag RAM latency
+  values should only use the first cell.
+- arm,dirty-latency : Cycles of latency for Dirty RAMs. This is a single cell.
+- arm,filter-ranges : <start length> Starting address and length of window to
+  filter. Addresses in the filter window are directed to the M1 port. Other
+  addresses will go to the M0 port.
+- interrupts : 1 combined interrupt.
+
+Example:
+
+L2: cache-controller {
+        compatible = "arm,pl310-cache";
+        reg = <0xfff12000 0x1000>;
+        arm,data-latency = <1 1 1>;
+        arm,tag-latency = <2 2 2>;
+        arm,filter-latency = <0x80000000 0x8000000>;
+        cache-unified;
+        cache-level = <2>;
+	interrupts = <45>;
+};

MAINTAINERS

@@ -688,6 +688,12 @@ F:	drivers/mtd/nand/bcm_umi_nand.c
 F:	drivers/mtd/nand/bcm_umi_bch.c
 F:	drivers/mtd/nand/nand_bcm_umi.h
 
+ARM/CALXEDA HIGHBANK ARCHITECTURE
+M:	Rob Herring <rob.herring@calxeda.com>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S:	Maintained
+F:	arch/arm/mach-highbank/
+
 ARM/CAVIUM NETWORKS CNS3XXX MACHINE SUPPORT
 M:	Anton Vorontsov <avorontsov@mvista.com>
 S:	Maintained

arch/arm/Kconfig

@@ -330,6 +330,20 @@ config ARCH_BCMRING
 	help
 	  Support for Broadcom's BCMRing platform.
 
+config ARCH_HIGHBANK
+	bool "Calxeda Highbank-based"
+	select ARCH_WANT_OPTIONAL_GPIOLIB
+	select ARM_AMBA
+	select ARM_GIC
+	select ARM_TIMER_SP804
+	select CLKDEV_LOOKUP
+	select CPU_V7
+	select GENERIC_CLOCKEVENTS
+	select HAVE_ARM_SCU
+	select USE_OF
+	help
+	  Support for the Calxeda Highbank SoC based boards.
+
 config ARCH_CLPS711X
 	bool "Cirrus Logic CLPS711x/EP721x-based"
 	select CPU_ARM720T
@@ -862,6 +876,7 @@ config ARCH_U300
 	select CLKDEV_LOOKUP
 	select HAVE_MACH_CLKDEV
 	select GENERIC_GPIO
+	select ARCH_REQUIRE_GPIOLIB
 	select NEED_MACH_MEMORY_H
 	help
 	  Support for ST-Ericsson U300 series mobile platforms.
@@ -1402,7 +1417,7 @@ config SMP
 	depends on REALVIEW_EB_ARM11MP || REALVIEW_EB_A9MP || \
 		 MACH_REALVIEW_PB11MP || MACH_REALVIEW_PBX || ARCH_OMAP4 || \
 		 ARCH_EXYNOS4 || ARCH_TEGRA || ARCH_U8500 || ARCH_VEXPRESS_CA9X4 || \
-		 ARCH_MSM_SCORPIONMP || ARCH_SHMOBILE
+		 ARCH_MSM_SCORPIONMP || ARCH_SHMOBILE || ARCH_HIGHBANK
 	select USE_GENERIC_SMP_HELPERS
 	select HAVE_ARM_SCU if !ARCH_MSM_SCORPIONMP
 	help

arch/arm/Kconfig.debug

@@ -65,13 +65,78 @@ config DEBUG_USER
 
 # These options are only for real kernel hackers who want to get their hands dirty.
 config DEBUG_LL
-	bool "Kernel low-level debugging functions"
+	bool "Kernel low-level debugging functions (read help!)"
 	depends on DEBUG_KERNEL
 	help
 	  Say Y here to include definitions of printascii, printch, printhex
 	  in the kernel.  This is helpful if you are debugging code that
 	  executes before the console is initialized.
 
+	  Note that selecting this option will limit the kernel to a single
+	  UART definition, as specified below. Attempting to boot the kernel
+	  image on a different platform *will not work*, so this option should
+	  not be enabled for kernels that are intended to be portable.
+
+choice
+	prompt "Kernel low-level debugging port"
+	depends on DEBUG_LL
+
+	config DEBUG_LL_UART_NONE
+		bool "No low-level debugging UART"
+		help
+		  Say Y here if your platform doesn't provide a UART option
+		  below. This relies on your platform choosing the right UART
+		  definition internally in order for low-level debugging to
+		  work.
+
+	config DEBUG_ICEDCC
+		bool "Kernel low-level debugging via EmbeddedICE DCC channel"
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the EmbeddedICE macrocell's DCC channel using
+		  co-processor 14. This is known to work on the ARM9 style ICE
+		  channel and on the XScale with the PEEDI.
+
+		  Note that the system will appear to hang during boot if there
+		  is nothing connected to read from the DCC.
+
+	config DEBUG_FOOTBRIDGE_COM1
+		bool "Kernel low-level debugging messages via footbridge 8250 at PCI COM1"
+		depends on FOOTBRIDGE
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the 8250 at PCI COM1.
+
+	config DEBUG_DC21285_PORT
+		bool "Kernel low-level debugging messages via footbridge serial port"
+		depends on FOOTBRIDGE
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the serial port in the DC21285 (Footbridge).
+
+	config DEBUG_CLPS711X_UART1
+		bool "Kernel low-level debugging messages via UART1"
+		depends on ARCH_CLPS711X
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the first serial port on these devices.
+
+	config DEBUG_CLPS711X_UART2
+		bool "Kernel low-level debugging messages via UART2"
+		depends on ARCH_CLPS711X
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the second serial port on these devices.
+
+	config DEBUG_HIGHBANK_UART
+		bool "Kernel low-level debugging messages via Highbank UART"
+		depends on ARCH_HIGHBANK
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the UART on Highbank based devices.
+
+endchoice
+
 config EARLY_PRINTK
 	bool "Early printk"
 	depends on DEBUG_LL
@@ -80,18 +145,6 @@ config EARLY_PRINTK
 	  kernel low-level debugging functions. Add earlyprintk to your
 	  kernel parameters to enable this console.
 
-config DEBUG_ICEDCC
-	bool "Kernel low-level debugging via EmbeddedICE DCC channel"
-	depends on DEBUG_LL
-	help
-	  Say Y here if you want the debug print routines to direct their
-	  output to the EmbeddedICE macrocell's DCC channel using
-	  co-processor 14. This is known to work on the ARM9 style ICE
-	  channel and on the XScale with the PEEDI.
-
-	  It does include a timeout to ensure that the system does not
-	  totally freeze when there is nothing connected to read.
-
 config OC_ETM
 	bool "On-chip ETM and ETB"
 	select ARM_AMBA
@@ -100,23 +153,6 @@ config OC_ETM
 	  buffer driver that will allow you to collect traces of the
 	  kernel code.
 
-config DEBUG_DC21285_PORT
-	bool "Kernel low-level debugging messages via footbridge serial port"
-	depends on DEBUG_LL && FOOTBRIDGE
-	help
-	  Say Y here if you want the debug print routines to direct their
-	  output to the serial port in the DC21285 (Footbridge). Saying N
-	  will cause the debug messages to appear on the first 16550
-	  serial port.
-
-config DEBUG_CLPS711X_UART2
-	bool "Kernel low-level debugging messages via UART2"
-	depends on DEBUG_LL && ARCH_CLPS711X
-	help
-	  Say Y here if you want the debug print routines to direct their
-	  output to the second serial port on these devices.  Saying N will
-	  cause the debug messages to appear on the first serial port.
-
 config DEBUG_S3C_UART
 	depends on PLAT_SAMSUNG
 	int "S3C UART to use for low-level debug"

arch/arm/Makefile

@@ -144,6 +144,7 @@ machine-$(CONFIG_ARCH_EBSA110)		:= ebsa110
 machine-$(CONFIG_ARCH_EP93XX)		:= ep93xx
 machine-$(CONFIG_ARCH_GEMINI)		:= gemini
 machine-$(CONFIG_ARCH_H720X)		:= h720x
+machine-$(CONFIG_ARCH_HIGHBANK)		:= highbank
 machine-$(CONFIG_ARCH_INTEGRATOR)	:= integrator
 machine-$(CONFIG_ARCH_IOP13XX)		:= iop13xx
 machine-$(CONFIG_ARCH_IOP32X)		:= iop32x

arch/arm/boot/dts/highbank.dts

@@ -0,0 +1,198 @@
+/*
+ * Copyright 2011 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/dts-v1/;
+
+/* First 4KB has pen for secondary cores. */
+/memreserve/ 0x00000000 0x0001000;
+
+/ {
+	model = "Calxeda Highbank";
+	compatible = "calxeda,highbank";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,cortex-a9";
+			reg = <0>;
+			next-level-cache = <&L2>;
+		};
+
+		cpu@1 {
+			compatible = "arm,cortex-a9";
+			reg = <1>;
+			next-level-cache = <&L2>;
+		};
+
+		cpu@2 {
+			compatible = "arm,cortex-a9";
+			reg = <2>;
+			next-level-cache = <&L2>;
+		};
+
+		cpu@3 {
+			compatible = "arm,cortex-a9";
+			reg = <3>;
+			next-level-cache = <&L2>;
+		};
+	};
+
+	memory {
+		name = "memory";
+		device_type = "memory";
+		reg = <0x00000000 0xff900000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyAMA0";
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		interrupt-parent = <&intc>;
+		ranges;
+
+		timer@fff10600 {
+			compatible = "arm,smp-twd";
+			reg = <0xfff10600 0x20>;
+			interrupts = <1 13 0xf04>;
+		};
+
+		watchdog@fff10620 {
+			compatible = "arm,cortex-a9-wdt";
+			reg = <0xfff10620 0x20>;
+			interrupts = <1 14 0xf04>;
+		};
+
+		intc: interrupt-controller@fff11000 {
+			compatible = "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#size-cells = <0>;
+			#address-cells = <1>;
+			interrupt-controller;
+			interrupt-parent;
+			reg = <0xfff11000 0x1000>,
+			      <0xfff10100 0x100>;
+		};
+
+		L2: l2-cache {
+			compatible = "arm,pl310-cache";
+			reg = <0xfff12000 0x1000>;
+			interrupts = <0 70 4>;
+			cache-unified;
+			cache-level = <2>;
+		};
+
+		pmu {
+			compatible = "arm,cortex-a9-pmu";
+			interrupts = <0 76 4  0 75 4  0 74 4  0 73 4>;
+		};
+
+		sata@ffe08000 {
+			compatible = "calxeda,hb-ahci";
+			reg = <0xffe08000 0x10000>;
+			interrupts = <0 83 4>;
+		};
+
+		sdhci@ffe0e000 {
+			compatible = "calxeda,hb-sdhci";
+			reg = <0xffe0e000 0x1000>;
+			interrupts = <0 90 4>;
+		};
+
+		ipc@fff20000 {
+			compatible = "arm,pl320", "arm,primecell";
+			reg = <0xfff20000 0x1000>;
+			interrupts = <0 7 4>;
+		};
+
+		gpioe: gpio@fff30000 {
+			#gpio-cells = <2>;
+			compatible = "arm,pl061", "arm,primecell";
+			gpio-controller;
+			reg = <0xfff30000 0x1000>;
+			interrupts = <0 14 4>;
+		};
+
+		gpiof: gpio@fff31000 {
+			#gpio-cells = <2>;
+			compatible = "arm,pl061", "arm,primecell";
+			gpio-controller;
+			reg = <0xfff31000 0x1000>;
+			interrupts = <0 15 4>;
+		};
+
+		gpiog: gpio@fff32000 {
+			#gpio-cells = <2>;
+			compatible = "arm,pl061", "arm,primecell";
+			gpio-controller;
+			reg = <0xfff32000 0x1000>;
+			interrupts = <0 16 4>;
+		};
+
+		gpioh: gpio@fff33000 {
+			#gpio-cells = <2>;
+			compatible = "arm,pl061", "arm,primecell";
+			gpio-controller;
+			reg = <0xfff33000 0x1000>;
+			interrupts = <0 17 4>;
+		};
+
+		timer {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0xfff34000 0x1000>;
+			interrupts = <0 18 4>;
+		};
+
+		rtc@fff35000 {
+			compatible = "arm,pl031", "arm,primecell";
+			reg = <0xfff35000 0x1000>;
+			interrupts = <0 19 4>;
+		};
+
+		serial@fff36000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0xfff36000 0x1000>;
+			interrupts = <0 20 4>;
+		};
+
+		smic@fff3a000 {
+			compatible = "ipmi-smic";
+			device_type = "ipmi";
+			reg = <0xfff3a000 0x1000>;
+			interrupts = <0 24 4>;
+			reg-size = <4>;
+			reg-spacing = <4>;
+		};
+
+		sregs@fff3c000 {
+			compatible = "calxeda,hb-sregs";
+			reg = <0xfff3c000 0x1000>;
+		};
+
+		dma@fff3d000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0xfff3d000 0x1000>;
+			interrupts = <0 92 4>;
+		};
+	};
+};

arch/arm/common/scoop.c

@@ -12,11 +12,11 @@
  */
 
 #include <linux/device.h>
+#include <linux/gpio.h>
 #include <linux/string.h>
 #include <linux/slab.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
-#include <asm/gpio.h>
 #include <asm/hardware/scoop.h>
 
 /* PCMCIA to Scoop linkage

arch/arm/include/asm/ecard.h

@@ -161,7 +161,6 @@ struct expansion_card {
 
 	/* Private internal data */
 	const char		*card_desc;	/* Card description		*/
-	CONST unsigned int	podaddr;	/* Base Linux address for card	*/
 	CONST loader_t		loader;		/* loader program */
 	u64			dma_mask;
 };

arch/arm/include/asm/gpio.h

@@ -4,4 +4,23 @@
 /* not all ARM platforms necessarily support this API ... */
 #include <mach/gpio.h>
 
+#ifndef __ARM_GPIOLIB_COMPLEX
+/* Note: this may rely upon the value of ARCH_NR_GPIOS set in mach/gpio.h */
+#include <asm-generic/gpio.h>
+
+/* The trivial gpiolib dispatchers */
+#define gpio_get_value  __gpio_get_value
+#define gpio_set_value  __gpio_set_value
+#define gpio_cansleep   __gpio_cansleep
+#endif
+
+/*
+ * Provide a default gpio_to_irq() which should satisfy every case.
+ * However, some platforms want to do this differently, so allow them
+ * to override it.
+ */
+#ifndef gpio_to_irq
+#define gpio_to_irq	__gpio_to_irq
+#endif
+
 #endif /* _ARCH_ARM_GPIO_H */

arch/arm/include/asm/hardware/cache-l2x0.h

@@ -52,6 +52,8 @@
 #define L2X0_LOCKDOWN_WAY_D_BASE	0x900
 #define L2X0_LOCKDOWN_WAY_I_BASE	0x904
 #define L2X0_LOCKDOWN_STRIDE		0x08
+#define L2X0_ADDR_FILTER_START		0xC00
+#define L2X0_ADDR_FILTER_END		0xC04
 #define L2X0_TEST_OPERATION		0xF00
 #define L2X0_LINE_DATA			0xF10
 #define L2X0_LINE_TAG			0xF30
@@ -65,8 +67,23 @@
 #define L2X0_CACHE_ID_PART_MASK		(0xf << 6)
 #define L2X0_CACHE_ID_PART_L210		(1 << 6)
 #define L2X0_CACHE_ID_PART_L310		(3 << 6)
+#define L2X0_CACHE_ID_RTL_MASK          0x3f
+#define L2X0_CACHE_ID_RTL_R0P0          0x0
+#define L2X0_CACHE_ID_RTL_R1P0          0x2
+#define L2X0_CACHE_ID_RTL_R2P0          0x4
+#define L2X0_CACHE_ID_RTL_R3P0          0x5
+#define L2X0_CACHE_ID_RTL_R3P1          0x6
+#define L2X0_CACHE_ID_RTL_R3P2          0x8
 
 #define L2X0_AUX_CTRL_MASK			0xc0000fff
+#define L2X0_AUX_CTRL_DATA_RD_LATENCY_SHIFT	0
+#define L2X0_AUX_CTRL_DATA_RD_LATENCY_MASK	0x7
+#define L2X0_AUX_CTRL_DATA_WR_LATENCY_SHIFT	3
+#define L2X0_AUX_CTRL_DATA_WR_LATENCY_MASK	(0x7 << 3)
+#define L2X0_AUX_CTRL_TAG_LATENCY_SHIFT		6
+#define L2X0_AUX_CTRL_TAG_LATENCY_MASK		(0x7 << 6)
+#define L2X0_AUX_CTRL_DIRTY_LATENCY_SHIFT	9
+#define L2X0_AUX_CTRL_DIRTY_LATENCY_MASK	(0x7 << 9)
 #define L2X0_AUX_CTRL_ASSOCIATIVITY_SHIFT	16
 #define L2X0_AUX_CTRL_WAY_SIZE_SHIFT		17
 #define L2X0_AUX_CTRL_WAY_SIZE_MASK		(0x7 << 17)
@@ -77,8 +94,40 @@
 #define L2X0_AUX_CTRL_INSTR_PREFETCH_SHIFT	29
 #define L2X0_AUX_CTRL_EARLY_BRESP_SHIFT		30
 
+#define L2X0_LATENCY_CTRL_SETUP_SHIFT	0
+#define L2X0_LATENCY_CTRL_RD_SHIFT	4
+#define L2X0_LATENCY_CTRL_WR_SHIFT	8
+
+#define L2X0_ADDR_FILTER_EN		1
+
 #ifndef __ASSEMBLY__
 extern void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask);
+#if defined(CONFIG_CACHE_L2X0) && defined(CONFIG_OF)
+extern int l2x0_of_init(__u32 aux_val, __u32 aux_mask);
+#else
+static inline int l2x0_of_init(__u32 aux_val, __u32 aux_mask)
+{
+	return -ENODEV;
+}
 #endif
 
+struct l2x0_regs {
+	unsigned long phy_base;
+	unsigned long aux_ctrl;
+	/*
+	 * Whether the following registers need to be saved/restored
+	 * depends on platform
+	 */
+	unsigned long tag_latency;
+	unsigned long data_latency;
+	unsigned long filter_start;
+	unsigned long filter_end;
+	unsigned long prefetch_ctrl;
+	unsigned long pwr_ctrl;
+};
+
+extern struct l2x0_regs l2x0_saved_regs;
+
+#endif /* __ASSEMBLY__ */
+
 #endif

arch/arm/include/asm/hardware/iop3xx-gpio.h

@@ -28,6 +28,8 @@
 #include <mach/hardware.h>
 #include <asm-generic/gpio.h>
 
+#define __ARM_GPIOLIB_COMPLEX
+
 #define IOP3XX_N_GPIOS	8
 
 static inline int gpio_get_value(unsigned gpio)

arch/arm/include/asm/io.h

@@ -109,6 +109,27 @@ static inline void __iomem *__typesafe_io(unsigned long addr)
  */
 #include <mach/io.h>
 
+/*
+ * This is the limit of PC card/PCI/ISA IO space, which is by default
+ * 64K if we have PC card, PCI or ISA support.  Otherwise, default to
+ * zero to prevent ISA/PCI drivers claiming IO space (and potentially
+ * oopsing.)
+ *
+ * Only set this larger if you really need inb() et.al. to operate over
+ * a larger address space.  Note that SOC_COMMON ioremaps each sockets
+ * IO space area, and so inb() et.al. must be defined to operate as per
+ * readb() et.al. on such platforms.
+ */
+#ifndef IO_SPACE_LIMIT
+#if defined(CONFIG_PCMCIA_SOC_COMMON) || defined(CONFIG_PCMCIA_SOC_COMMON_MODULE)
+#define IO_SPACE_LIMIT ((resource_size_t)0xffffffff)
+#elif defined(CONFIG_PCI) || defined(CONFIG_ISA) || defined(CONFIG_PCCARD)
+#define IO_SPACE_LIMIT ((resource_size_t)0xffff)
+#else
+#define IO_SPACE_LIMIT ((resource_size_t)0)
+#endif
+#endif
+
 /*
  *  IO port access primitives
  *  -------------------------

arch/arm/include/asm/outercache.h

@@ -34,6 +34,7 @@ struct outer_cache_fns {
 	void (*sync)(void);
 #endif
 	void (*set_debug)(unsigned long);
+	void (*resume)(void);
 };
 
 #ifdef CONFIG_OUTER_CACHE
@@ -74,6 +75,12 @@ static inline void outer_disable(void)
 		outer_cache.disable();
 }
 
+static inline void outer_resume(void)
+{
+	if (outer_cache.resume)
+		outer_cache.resume();
+}
+
 #else
 
 static inline void outer_inv_range(phys_addr_t start, phys_addr_t end)

arch/arm/kernel/asm-offsets.c

@@ -20,6 +20,7 @@
 #include <asm/thread_info.h>
 #include <asm/memory.h>
 #include <asm/procinfo.h>
+#include <asm/hardware/cache-l2x0.h>
 #include <linux/kbuild.h>
 
 /*
@@ -92,6 +93,17 @@ int main(void)
   DEFINE(S_OLD_R0,		offsetof(struct pt_regs, ARM_ORIG_r0));
   DEFINE(S_FRAME_SIZE,		sizeof(struct pt_regs));
   BLANK();
+#ifdef CONFIG_CACHE_L2X0
+  DEFINE(L2X0_R_PHY_BASE,	offsetof(struct l2x0_regs, phy_base));
+  DEFINE(L2X0_R_AUX_CTRL,	offsetof(struct l2x0_regs, aux_ctrl));
+  DEFINE(L2X0_R_TAG_LATENCY,	offsetof(struct l2x0_regs, tag_latency));
+  DEFINE(L2X0_R_DATA_LATENCY,	offsetof(struct l2x0_regs, data_latency));
+  DEFINE(L2X0_R_FILTER_START,	offsetof(struct l2x0_regs, filter_start));
+  DEFINE(L2X0_R_FILTER_END,	offsetof(struct l2x0_regs, filter_end));
+  DEFINE(L2X0_R_PREFETCH_CTRL,	offsetof(struct l2x0_regs, prefetch_ctrl));
+  DEFINE(L2X0_R_PWR_CTRL,	offsetof(struct l2x0_regs, pwr_ctrl));
+  BLANK();
+#endif
 #ifdef CONFIG_CPU_HAS_ASID
   DEFINE(MM_CONTEXT_ID,		offsetof(struct mm_struct, context.id));
   BLANK();

arch/arm/kernel/ecard.c

@@ -237,7 +237,7 @@ static void ecard_init_pgtables(struct mm_struct *mm)
 
 	memcpy(dst_pgd, src_pgd, sizeof(pgd_t) * (IO_SIZE / PGDIR_SIZE));
 
-	src_pgd = pgd_offset(mm, EASI_BASE);
+	src_pgd = pgd_offset(mm, (unsigned long)EASI_BASE);
 	dst_pgd = pgd_offset(mm, EASI_START);
 
 	memcpy(dst_pgd, src_pgd, sizeof(pgd_t) * (EASI_SIZE / PGDIR_SIZE));
@@ -674,44 +674,37 @@ static int __init ecard_probeirqhw(void)
 #define ecard_probeirqhw() (0)
 #endif
 
-#ifndef IO_EC_MEMC8_BASE
-#define IO_EC_MEMC8_BASE 0
-#endif
-
-static unsigned int __ecard_address(ecard_t *ec, card_type_t type, card_speed_t speed)
+static void __iomem *__ecard_address(ecard_t *ec, card_type_t type, card_speed_t speed)
 {
-	unsigned long address = 0;
+	void __iomem *address = NULL;
 	int slot = ec->slot_no;
 
 	if (ec->slot_no == 8)
-		return IO_EC_MEMC8_BASE;
+		return ECARD_MEMC8_BASE;
 
 	ectcr &= ~(1 << slot);
 
 	switch (type) {
 	case ECARD_MEMC:
 		if (slot < 4)
-			address = IO_EC_MEMC_BASE + (slot << 12);
+			address = ECARD_MEMC_BASE + (slot << 14);
 		break;
 
 	case ECARD_IOC:
 		if (slot < 4)
-			address = IO_EC_IOC_BASE + (slot << 12);
-#ifdef IO_EC_IOC4_BASE
+			address = ECARD_IOC_BASE + (slot << 14);
 		else
-			address = IO_EC_IOC4_BASE + ((slot - 4) << 12);
-#endif
+			address = ECARD_IOC4_BASE + ((slot - 4) << 14);
 		if (address)
-			address +=  speed << 17;
+			address += speed << 19;
 		break;
 
-#ifdef IO_EC_EASI_BASE
 	case ECARD_EASI:
-		address = IO_EC_EASI_BASE + (slot << 22);
+		address = ECARD_EASI_BASE + (slot << 24);
 		if (speed == ECARD_FAST)
 			ectcr |= 1 << slot;
 		break;
-#endif
+
 	default:
 		break;
 	}
@@ -990,6 +983,7 @@ ecard_probe(int slot, card_type_t type)
 	ecard_t **ecp;
 	ecard_t *ec;
 	struct ex_ecid cid;
+	void __iomem *addr;
 	int i, rc;
 
 	ec = ecard_alloc_card(type, slot);
@@ -999,7 +993,7 @@ ecard_probe(int slot, card_type_t type)
 	}
 
 	rc = -ENODEV;
-	if ((ec->podaddr = __ecard_address(ec, type, ECARD_SYNC)) == 0)
+	if ((addr = __ecard_address(ec, type, ECARD_SYNC)) == NULL)
 		goto nodev;
 
 	cid.r_zero = 1;
@@ -1019,7 +1013,7 @@ ecard_probe(int slot, card_type_t type)
 	ec->cid.fiqmask = cid.r_fiqmask;
 	ec->cid.fiqoff  = ecard_gets24(cid.r_fiqoff);
 	ec->fiqaddr	=
-	ec->irqaddr	= (void __iomem *)ioaddr(ec->podaddr);
+	ec->irqaddr	= addr;
 
 	if (ec->cid.is) {
 		ec->irqmask = ec->cid.irqmask;
@@ -1048,10 +1042,8 @@ ecard_probe(int slot, card_type_t type)
 		set_irq_flags(ec->irq, IRQF_VALID);
 	}
 
-#ifdef IO_EC_MEMC8_BASE
 	if (slot == 8)
 		ec->irq = 11;
-#endif
 #ifdef CONFIG_ARCH_RPC
 	/* On RiscPC, only first two slots have DMA capability */
 	if (slot < 2)
@@ -1097,9 +1089,7 @@ static int __init ecard_init(void)
 			ecard_probe(slot, ECARD_IOC);
 	}
 
-#ifdef IO_EC_MEMC8_BASE
 	ecard_probe(8, ECARD_IOC);
-#endif
 
 	irqhw = ecard_probeirqhw();
 

arch/arm/mach-at91/at91cap9_devices.c

@@ -16,6 +16,7 @@
 #include <asm/mach/irq.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 
@@ -23,7 +24,6 @@
 
 #include <mach/board.h>
 #include <mach/cpu.h>
-#include <mach/gpio.h>
 #include <mach/at91cap9.h>
 #include <mach/at91cap9_matrix.h>
 #include <mach/at91sam9_smc.h>

arch/arm/mach-at91/at91rm9200_devices.c

@@ -14,11 +14,11 @@
 #include <asm/mach/map.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91rm9200.h>
 #include <mach/at91rm9200_mc.h>
 

arch/arm/mach-at91/at91sam9260_devices.c

@@ -13,11 +13,11 @@
 #include <asm/mach/map.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/cpu.h>
 #include <mach/at91sam9260.h>
 #include <mach/at91sam9260_matrix.h>

arch/arm/mach-at91/at91sam9261_devices.c

@@ -14,6 +14,7 @@
 #include <asm/mach/map.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 
@@ -21,7 +22,6 @@
 #include <video/atmel_lcdc.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9261.h>
 #include <mach/at91sam9261_matrix.h>
 #include <mach/at91sam9_smc.h>

arch/arm/mach-at91/at91sam9263_devices.c

@@ -13,6 +13,7 @@
 #include <asm/mach/map.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 
@@ -20,7 +21,6 @@
 #include <video/atmel_lcdc.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9263.h>
 #include <mach/at91sam9263_matrix.h>
 #include <mach/at91sam9_smc.h>

arch/arm/mach-at91/at91sam9g45_devices.c

@@ -13,6 +13,7 @@
 #include <asm/mach/map.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 #include <linux/atmel-mci.h>
@@ -21,7 +22,6 @@
 #include <video/atmel_lcdc.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9g45.h>
 #include <mach/at91sam9g45_matrix.h>
 #include <mach/at91sam9_smc.h>

arch/arm/mach-at91/at91sam9rl_devices.c

@@ -10,6 +10,7 @@
 #include <asm/mach/map.h>
 
 #include <linux/dma-mapping.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/i2c-gpio.h>
 
@@ -17,7 +18,6 @@
 #include <video/atmel_lcdc.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9rl.h>
 #include <mach/at91sam9rl_matrix.h>
 #include <mach/at91sam9_smc.h>

arch/arm/mach-at91/board-1arm.c

@@ -19,6 +19,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -34,7 +35,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/cpu.h>
 
 #include "generic.h"

arch/arm/mach-at91/board-afeb-9260v1.c

@@ -25,6 +25,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -43,7 +44,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 
 #include "generic.h"
 

arch/arm/mach-at91/board-cam60.c

@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -38,7 +39,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 
 #include "sam9_smc.h"

arch/arm/mach-at91/board-cap9adk.c

@@ -22,6 +22,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -41,7 +42,6 @@
 #include <asm/mach/map.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91cap9_matrix.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/system_rev.h>

arch/arm/mach-at91/board-carmeva.c

@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -35,7 +36,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 
 #include "generic.h"
 

arch/arm/mach-at91/board-cpu9krea.c

@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -40,7 +41,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91sam9260_matrix.h>
 

arch/arm/mach-at91/board-cpuat91.c

@@ -19,6 +19,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -36,7 +37,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91rm9200_mc.h>
 #include <mach/cpu.h>
 

arch/arm/mach-at91/board-csb337.c

@@ -19,6 +19,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -38,7 +39,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 
 #include "generic.h"
 

arch/arm/mach-at91/board-csb637.c

@@ -20,6 +20,7 @@
 
 #include <linux/types.h>
 #include <linux/init.h>
+#include <linux/gpio.h>
 #include <linux/mm.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
@@ -35,7 +36,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 
 #include "generic.h"
 

arch/arm/mach-at91/board-eb9200.c

@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -35,7 +36,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 
 #include "generic.h"
 

arch/arm/mach-at91/board-ecbat91.c

@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -37,7 +38,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/cpu.h>
 
 #include "generic.h"

arch/arm/mach-at91/board-kafa.c

@@ -19,6 +19,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -34,7 +35,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/cpu.h>
 
 #include "generic.h"

arch/arm/mach-at91/board-kb9202.c

@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -35,7 +36,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/cpu.h>
 #include <mach/at91rm9200_mc.h>
 

arch/arm/mach-at91/board-neocore926.c

@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -44,7 +45,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 
 #include "sam9_smc.h"

arch/arm/mach-at91/board-picotux200.c

@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -37,7 +38,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91rm9200_mc.h>
 
 #include "generic.h"

arch/arm/mach-at91/board-qil-a9260.c

@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -40,7 +41,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 

arch/arm/mach-at91/board-rm9200dk.c

@@ -22,6 +22,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -39,7 +40,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91rm9200_mc.h>
 
 #include "generic.h"

arch/arm/mach-at91/board-rm9200ek.c

@@ -22,6 +22,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -39,7 +40,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91rm9200_mc.h>
 
 #include "generic.h"

arch/arm/mach-at91/board-sam9-l9260.c

@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -37,7 +38,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 
 #include "sam9_smc.h"

arch/arm/mach-at91/board-sam9260ek.c

@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -41,7 +42,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 #include <mach/system_rev.h>

arch/arm/mach-at91/board-sam9261ek.c

@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -45,7 +46,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 #include <mach/system_rev.h>

arch/arm/mach-at91/board-sam9263ek.c

@@ -20,6 +20,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -44,7 +45,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 #include <mach/system_rev.h>

arch/arm/mach-at91/board-sam9g20ek.c

@@ -18,6 +18,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -41,7 +42,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/system_rev.h>
 

arch/arm/mach-at91/board-sam9m10g45ek.c

@@ -14,6 +14,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -38,7 +39,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 #include <mach/system_rev.h>

arch/arm/mach-at91/board-sam9rlek.c

@@ -8,6 +8,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -30,7 +31,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 

arch/arm/mach-at91/board-usb-a9260.c

@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -40,7 +41,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 

arch/arm/mach-at91/board-usb-a9263.c

@@ -21,6 +21,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -39,7 +40,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91sam9_smc.h>
 #include <mach/at91_shdwc.h>
 

arch/arm/mach-at91/board-yl-9200.c

@@ -22,6 +22,7 @@
  */
 
 #include <linux/types.h>
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/mm.h>
 #include <linux/module.h>
@@ -43,7 +44,6 @@
 
 #include <mach/hardware.h>
 #include <mach/board.h>
-#include <mach/gpio.h>
 #include <mach/at91rm9200_mc.h>
 #include <mach/cpu.h>
 

arch/arm/mach-at91/gpio.c

@@ -11,6 +11,7 @@
 
 #include <linux/clk.h>
 #include <linux/errno.h>
+#include <linux/gpio.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
 #include <linux/debugfs.h>
@@ -22,9 +23,6 @@
 
 #include <mach/hardware.h>
 #include <mach/at91_pio.h>
-#include <mach/gpio.h>
-
-#include <asm/gpio.h>
 
 #include "generic.h"
 

arch/arm/mach-at91/include/mach/gpio.h

@@ -214,11 +214,6 @@ extern void at91_gpio_resume(void);
  */
 
 #include <asm/errno.h>
-#include <asm-generic/gpio.h>		/* cansleep wrappers */
-
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
 
 #define gpio_to_irq(gpio) (gpio)
 #define irq_to_gpio(irq)  (irq)

arch/arm/mach-at91/leds.c

@@ -9,13 +9,13 @@
  * 2 of the License, or (at your option) any later version.
 */
 
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
 
 #include <mach/board.h>
-#include <mach/gpio.h>
 
 
 /* ------------------------------------------------------------------------- */

arch/arm/mach-at91/pm.c

@@ -10,6 +10,7 @@
  * (at your option) any later version.
  */
 
+#include <linux/gpio.h>
 #include <linux/suspend.h>
 #include <linux/sched.h>
 #include <linux/proc_fs.h>
@@ -25,7 +26,6 @@
 #include <asm/mach/irq.h>
 
 #include <mach/at91_pmc.h>
-#include <mach/gpio.h>
 #include <mach/cpu.h>
 
 #include "generic.h"

arch/arm/mach-davinci/Makefile

@@ -5,7 +5,7 @@
 
 # Common objects
 obj-y 			:= time.o clock.o serial.o io.o psc.o \
-			   gpio.o dma.o usb.o common.o sram.o aemif.o
+			   dma.o usb.o common.o sram.o aemif.o
 
 obj-$(CONFIG_DAVINCI_MUX)		+= mux.o
 
@@ -17,7 +17,6 @@ obj-$(CONFIG_ARCH_DAVINCI_DM365)	+= dm365.o devices.o
 obj-$(CONFIG_ARCH_DAVINCI_DA830)        += da830.o devices-da8xx.o
 obj-$(CONFIG_ARCH_DAVINCI_DA850)        += da850.o devices-da8xx.o
 obj-$(CONFIG_ARCH_DAVINCI_TNETV107X)    += tnetv107x.o devices-tnetv107x.o
-obj-$(CONFIG_ARCH_DAVINCI_TNETV107X)    += gpio-tnetv107x.o
 
 obj-$(CONFIG_AINTC)			+= irq.o
 obj-$(CONFIG_CP_INTC)			+= cp_intc.o

arch/arm/mach-davinci/da830.c

@@ -8,6 +8,7 @@
  * is licensed "as is" without any warranty of any kind, whether express
  * or implied.
  */
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/clk.h>
 
@@ -19,7 +20,7 @@
 #include <mach/common.h>
 #include <mach/time.h>
 #include <mach/da8xx.h>
-#include <mach/gpio.h>
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"

arch/arm/mach-davinci/da850.c

@@ -11,6 +11,7 @@
  * is licensed "as is" without any warranty of any kind, whether express
  * or implied.
  */
+#include <linux/gpio.h>
 #include <linux/init.h>
 #include <linux/clk.h>
 #include <linux/platform_device.h>
@@ -27,7 +28,7 @@
 #include <mach/da8xx.h>
 #include <mach/cpufreq.h>
 #include <mach/pm.h>
-#include <mach/gpio.h>
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"

arch/arm/mach-davinci/dm355.c

@@ -13,7 +13,6 @@
 #include <linux/serial_8250.h>
 #include <linux/platform_device.h>
 #include <linux/dma-mapping.h>
-#include <linux/gpio.h>
 
 #include <linux/spi/spi.h>
 
@@ -30,6 +29,7 @@
 #include <mach/common.h>
 #include <mach/asp.h>
 #include <mach/spi.h>
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"

arch/arm/mach-davinci/dm365.c

@@ -17,7 +17,6 @@
 #include <linux/serial_8250.h>
 #include <linux/platform_device.h>
 #include <linux/dma-mapping.h>
-#include <linux/gpio.h>
 #include <linux/spi/spi.h>
 
 #include <asm/mach/map.h>
@@ -34,7 +33,7 @@
 #include <mach/asp.h>
 #include <mach/keyscan.h>
 #include <mach/spi.h>
-
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"

arch/arm/mach-davinci/dm644x.c

@@ -12,7 +12,6 @@
 #include <linux/clk.h>
 #include <linux/serial_8250.h>
 #include <linux/platform_device.h>
-#include <linux/gpio.h>
 
 #include <asm/mach/map.h>
 
@@ -26,6 +25,7 @@
 #include <mach/serial.h>
 #include <mach/common.h>
 #include <mach/asp.h>
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"

arch/arm/mach-davinci/dm646x.c

@@ -13,7 +13,6 @@
 #include <linux/clk.h>
 #include <linux/serial_8250.h>
 #include <linux/platform_device.h>
-#include <linux/gpio.h>
 
 #include <asm/mach/map.h>
 
@@ -27,6 +26,7 @@
 #include <mach/serial.h>
 #include <mach/common.h>
 #include <mach/asp.h>
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"

arch/arm/mach-davinci/include/mach/gpio-davinci.h

@@ -0,0 +1,91 @@
+/*
+ * TI DaVinci GPIO Support
+ *
+ * Copyright (c) 2006 David Brownell
+ * Copyright (c) 2007, MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef	__DAVINCI_DAVINCI_GPIO_H
+#define	__DAVINCI_DAVINCI_GPIO_H
+
+#include <linux/io.h>
+#include <linux/spinlock.h>
+
+#include <asm-generic/gpio.h>
+
+#include <mach/irqs.h>
+#include <mach/common.h>
+
+#define DAVINCI_GPIO_BASE 0x01C67000
+
+enum davinci_gpio_type {
+	GPIO_TYPE_DAVINCI = 0,
+	GPIO_TYPE_TNETV107X,
+};
+
+/*
+ * basic gpio routines
+ *
+ * board-specific init should be done by arch/.../.../board-XXX.c (maybe
+ * initializing banks together) rather than boot loaders; kexec() won't
+ * go through boot loaders.
+ *
+ * the gpio clock will be turned on when gpios are used, and you may also
+ * need to pay attention to PINMUX registers to be sure those pins are
+ * used as gpios, not with other peripherals.
+ *
+ * On-chip GPIOs are numbered 0..(DAVINCI_N_GPIO-1).  For documentation,
+ * and maybe for later updates, code may write GPIO(N).  These may be
+ * all 1.8V signals, all 3.3V ones, or a mix of the two.  A given chip
+ * may not support all the GPIOs in that range.
+ *
+ * GPIOs can also be on external chips, numbered after the ones built-in
+ * to the DaVinci chip.  For now, they won't be usable as IRQ sources.
+ */
+#define	GPIO(X)		(X)		/* 0 <= X <= (DAVINCI_N_GPIO - 1) */
+
+/* Convert GPIO signal to GPIO pin number */
+#define GPIO_TO_PIN(bank, gpio)	(16 * (bank) + (gpio))
+
+struct davinci_gpio_controller {
+	struct gpio_chip	chip;
+	int			irq_base;
+	spinlock_t		lock;
+	void __iomem		*regs;
+	void __iomem		*set_data;
+	void __iomem		*clr_data;
+	void __iomem		*in_data;
+};
+
+/* The __gpio_to_controller() and __gpio_mask() functions inline to constants
+ * with constant parameters; or in outlined code they execute at runtime.
+ *
+ * You'd access the controller directly when reading or writing more than
+ * one gpio value at a time, and to support wired logic where the value
+ * being driven by the cpu need not match the value read back.
+ *
+ * These are NOT part of the cross-platform GPIO interface
+ */
+static inline struct davinci_gpio_controller *
+__gpio_to_controller(unsigned gpio)
+{
+	struct davinci_gpio_controller *ctlrs = davinci_soc_info.gpio_ctlrs;
+	int index = gpio / 32;
+
+	if (!ctlrs || index >= davinci_soc_info.gpio_ctlrs_num)
+		return NULL;
+
+	return ctlrs + index;
+}
+
+static inline u32 __gpio_mask(unsigned gpio)
+{
+	return 1 << (gpio % 32);
+}
+
+#endif	/* __DAVINCI_DAVINCI_GPIO_H */

arch/arm/mach-davinci/include/mach/gpio.h

@@ -13,80 +13,10 @@
 #ifndef	__DAVINCI_GPIO_H
 #define	__DAVINCI_GPIO_H
 
-#include <linux/io.h>
-#include <linux/spinlock.h>
-
 #include <asm-generic/gpio.h>
 
-#include <mach/irqs.h>
-#include <mach/common.h>
-
-#define DAVINCI_GPIO_BASE 0x01C67000
-
-enum davinci_gpio_type {
-	GPIO_TYPE_DAVINCI = 0,
-	GPIO_TYPE_TNETV107X,
-};
-
-/*
- * basic gpio routines
- *
- * board-specific init should be done by arch/.../.../board-XXX.c (maybe
- * initializing banks together) rather than boot loaders; kexec() won't
- * go through boot loaders.
- *
- * the gpio clock will be turned on when gpios are used, and you may also
- * need to pay attention to PINMUX registers to be sure those pins are
- * used as gpios, not with other peripherals.
- *
- * On-chip GPIOs are numbered 0..(DAVINCI_N_GPIO-1).  For documentation,
- * and maybe for later updates, code may write GPIO(N).  These may be
- * all 1.8V signals, all 3.3V ones, or a mix of the two.  A given chip
- * may not support all the GPIOs in that range.
- *
- * GPIOs can also be on external chips, numbered after the ones built-in
- * to the DaVinci chip.  For now, they won't be usable as IRQ sources.
- */
-#define	GPIO(X)		(X)		/* 0 <= X <= (DAVINCI_N_GPIO - 1) */
-
-/* Convert GPIO signal to GPIO pin number */
-#define GPIO_TO_PIN(bank, gpio)	(16 * (bank) + (gpio))
-
-struct davinci_gpio_controller {
-	struct gpio_chip	chip;
-	int			irq_base;
-	spinlock_t		lock;
-	void __iomem		*regs;
-	void __iomem		*set_data;
-	void __iomem		*clr_data;
-	void __iomem		*in_data;
-};
-
-/* The __gpio_to_controller() and __gpio_mask() functions inline to constants
- * with constant parameters; or in outlined code they execute at runtime.
- *
- * You'd access the controller directly when reading or writing more than
- * one gpio value at a time, and to support wired logic where the value
- * being driven by the cpu need not match the value read back.
- *
- * These are NOT part of the cross-platform GPIO interface
- */
-static inline struct davinci_gpio_controller *
-__gpio_to_controller(unsigned gpio)
-{
-	struct davinci_gpio_controller *ctlrs = davinci_soc_info.gpio_ctlrs;
-	int index = gpio / 32;
-
-	if (!ctlrs || index >= davinci_soc_info.gpio_ctlrs_num)
-		return NULL;
-
-	return ctlrs + index;
-}
-
-static inline u32 __gpio_mask(unsigned gpio)
-{
-	return 1 << (gpio % 32);
-}
+/* The inline versions use the static inlines in the driver header */
+#include "gpio-davinci.h"
 
 /*
  * The get/set/clear functions will inline when called with constant
@@ -147,11 +77,6 @@ static inline int gpio_cansleep(unsigned gpio)
 		return __gpio_cansleep(gpio);
 }
 
-static inline int gpio_to_irq(unsigned gpio)
-{
-	return __gpio_to_irq(gpio);
-}
-
 static inline int irq_to_gpio(unsigned irq)
 {
 	/* don't support the reverse mapping */

arch/arm/mach-davinci/tnetv107x.c

@@ -12,6 +12,7 @@
  * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  */
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/clk.h>
@@ -27,9 +28,9 @@
 #include <mach/psc.h>
 #include <mach/cp_intc.h>
 #include <mach/irqs.h>
-#include <mach/gpio.h>
 #include <mach/hardware.h>
 #include <mach/tnetv107x.h>
+#include <mach/gpio-davinci.h>
 
 #include "clock.h"
 #include "mux.h"

arch/arm/mach-ebsa110/include/mach/io.h

@@ -13,8 +13,6 @@
 #ifndef __ASM_ARM_ARCH_IO_H
 #define __ASM_ARM_ARCH_IO_H
 
-#define IO_SPACE_LIMIT 0xffff
-
 u8 __inb8(unsigned int port);
 void __outb8(u8  val, unsigned int port);
 

arch/arm/mach-ep93xx/core.c

@@ -38,6 +38,7 @@
 #include <mach/fb.h>
 #include <mach/ep93xx_keypad.h>
 #include <mach/ep93xx_spi.h>
+#include <mach/gpio-ep93xx.h>
 
 #include <asm/mach/map.h>
 #include <asm/mach/time.h>

arch/arm/mach-ep93xx/edb93xx.c

@@ -37,6 +37,7 @@
 #include <mach/hardware.h>
 #include <mach/fb.h>
 #include <mach/ep93xx_spi.h>
+#include <mach/gpio-ep93xx.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>

arch/arm/mach-ep93xx/include/mach/gpio-ep93xx.h

@@ -1,9 +1,7 @@
-/*
- * arch/arm/mach-ep93xx/include/mach/gpio.h
- */
+/* Include file for the EP93XX GPIO controller machine specifics */
 
-#ifndef __ASM_ARCH_GPIO_H
-#define __ASM_ARCH_GPIO_H
+#ifndef __GPIO_EP93XX_H
+#define __GPIO_EP93XX_H
 
 /* GPIO port A.  */
 #define EP93XX_GPIO_LINE_A(x)		((x) + 0)
@@ -99,22 +97,4 @@
 /* maximum value for irq capable line identifiers */
 #define EP93XX_GPIO_LINE_MAX_IRQ	EP93XX_GPIO_LINE_F(7)
 
-/* new generic GPIO API - see Documentation/gpio.txt */
-
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
-
-/*
- * Map GPIO A0..A7  (0..7)  to irq 64..71,
- *          B0..B7  (7..15) to irq 72..79, and
- *          F0..F7 (16..24) to irq 80..87.
- */
-#define gpio_to_irq(gpio)	\
-	(((gpio) <= EP93XX_GPIO_LINE_MAX_IRQ) ? (64 + (gpio)) : -EINVAL)
-
-#define irq_to_gpio(irq)	((irq) - gpio_to_irq(0))
-
-#endif
+#endif /* __GPIO_EP93XX_H */

arch/arm/mach-ep93xx/simone.c

@@ -18,12 +18,12 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
-#include <linux/gpio.h>
 #include <linux/i2c.h>
 #include <linux/i2c-gpio.h>
 
 #include <mach/hardware.h>
 #include <mach/fb.h>
+#include <mach/gpio-ep93xx.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>

arch/arm/mach-ep93xx/snappercl15.c

@@ -20,7 +20,6 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/io.h>
-#include <linux/gpio.h>
 #include <linux/i2c.h>
 #include <linux/i2c-gpio.h>
 #include <linux/fb.h>
@@ -30,6 +29,7 @@
 
 #include <mach/hardware.h>
 #include <mach/fb.h>
+#include <mach/gpio-ep93xx.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>

arch/arm/mach-exynos4/include/mach/gpio.h

@@ -13,11 +13,6 @@
 #ifndef __ASM_ARCH_GPIO_H
 #define __ASM_ARCH_GPIO_H __FILE__
 
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
-#define gpio_to_irq	__gpio_to_irq
-
 /* Practically, GPIO banks up to GPZ are the configurable gpio banks */
 
 /* GPIO bank sizes */
@@ -151,6 +146,4 @@ enum s5p_gpio_number {
 #define ARCH_NR_GPIOS		(EXYNOS4_GPZ(EXYNOS4_GPIO_Z_NR) +	\
 				 CONFIG_SAMSUNG_GPIO_EXTRA + 1)
 
-#include <asm-generic/gpio.h>
-
 #endif /* __ASM_ARCH_GPIO_H */

arch/arm/mach-footbridge/include/mach/io.h

@@ -23,8 +23,6 @@
 #define PCIO_SIZE       0x00100000
 #define PCIO_BASE       MMU_IO(0xff000000, 0x7c000000)
 
-#define IO_SPACE_LIMIT 0xffff
-
 /*
  * Translation of various region addresses to virtual addresses
  */

arch/arm/mach-gemini/include/mach/gpio.h

@@ -13,11 +13,6 @@
 #define __MACH_GPIO_H__
 
 #include <mach/irqs.h>
-#include <asm-generic/gpio.h>
-
-#define gpio_get_value	__gpio_get_value
-#define gpio_set_value	__gpio_set_value
-#define gpio_cansleep	__gpio_cansleep
 
 #define gpio_to_irq(x)	((x) + GPIO_IRQ_BASE)
 #define irq_to_gpio(x)	((x) - GPIO_IRQ_BASE)

arch/arm/mach-highbank/Makefile

@@ -0,0 +1,6 @@
+obj-y					:= clock.o highbank.o system.o
+obj-$(CONFIG_DEBUG_HIGHBANK_UART)	+= lluart.o
+obj-$(CONFIG_SMP)			+= platsmp.o
+obj-$(CONFIG_LOCAL_TIMERS)		+= localtimer.o
+obj-$(CONFIG_HOTPLUG_CPU)		+= hotplug.o
+obj-$(CONFIG_PM_SLEEP)			+= pm.o

arch/arm/mach-highbank/Makefile.boot

@@ -0,0 +1 @@
+zreladdr-y	:= 0x00008000

arch/arm/mach-highbank/clock.c

@@ -0,0 +1,62 @@
+/*
+ * Copyright 2011 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+
+struct clk {
+	unsigned long rate;
+};
+
+int clk_enable(struct clk *clk)
+{
+	return 0;
+}
+
+void clk_disable(struct clk *clk)
+{}
+
+unsigned long clk_get_rate(struct clk *clk)
+{
+	return clk->rate;
+}
+
+long clk_round_rate(struct clk *clk, unsigned long rate)
+{
+	return clk->rate;
+}
+
+int clk_set_rate(struct clk *clk, unsigned long rate)
+{
+	return 0;
+}
+
+static struct clk eclk = { .rate = 200000000 };
+static struct clk pclk = { .rate = 150000000 };
+
+static struct clk_lookup lookups[] = {
+	{ .clk = &pclk, .con_id = "apb_pclk", },
+	{ .clk = &pclk, .dev_id = "sp804", },
+	{ .clk = &eclk, .dev_id = "ffe0e000.sdhci", },
+	{ .clk = &pclk, .dev_id = "fff36000.serial", },
+};
+
+void __init highbank_clocks_init(void)
+{
+	clkdev_add_table(lookups, ARRAY_SIZE(lookups));
+}

arch/arm/mach-highbank/core.h

@@ -0,0 +1,9 @@
+extern void highbank_set_cpu_jump(int cpu, void *jump_addr);
+extern void highbank_clocks_init(void);
+extern void __iomem *scu_base_addr;
+#ifdef CONFIG_DEBUG_HIGHBANK_UART
+extern void highbank_lluart_map_io(void);
+#else
+static inline void highbank_lluart_map_io(void) {}
+#endif
+

arch/arm/mach-highbank/highbank.c

@@ -0,0 +1,145 @@
+/*
+ * Copyright 2010-2011 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+
+#include <asm/cacheflush.h>
+#include <asm/unified.h>
+#include <asm/smp_scu.h>
+#include <asm/hardware/arm_timer.h>
+#include <asm/hardware/timer-sp.h>
+#include <asm/hardware/gic.h>
+#include <asm/hardware/cache-l2x0.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/time.h>
+#include <mach/irqs.h>
+
+#include "core.h"
+#include "sysregs.h"
+
+void __iomem *sregs_base;
+
+#define HB_SCU_VIRT_BASE	0xfee00000
+void __iomem *scu_base_addr = ((void __iomem *)(HB_SCU_VIRT_BASE));
+
+static struct map_desc scu_io_desc __initdata = {
+	.virtual	= HB_SCU_VIRT_BASE,
+	.pfn		= 0, /* run-time */
+	.length		= SZ_4K,
+	.type		= MT_DEVICE,
+};
+
+static void __init highbank_scu_map_io(void)
+{
+	unsigned long base;
+
+	/* Get SCU base */
+	asm("mrc p15, 4, %0, c15, c0, 0" : "=r" (base));
+
+	scu_io_desc.pfn = __phys_to_pfn(base);
+	iotable_init(&scu_io_desc, 1);
+}
+
+static void __init highbank_map_io(void)
+{
+	highbank_scu_map_io();
+	highbank_lluart_map_io();
+}
+
+#define HB_JUMP_TABLE_PHYS(cpu)		(0x40 + (0x10 * (cpu)))
+#define HB_JUMP_TABLE_VIRT(cpu)		phys_to_virt(HB_JUMP_TABLE_PHYS(cpu))
+
+void highbank_set_cpu_jump(int cpu, void *jump_addr)
+{
+	writel(BSYM(virt_to_phys(jump_addr)), HB_JUMP_TABLE_VIRT(cpu));
+	__cpuc_flush_dcache_area(HB_JUMP_TABLE_VIRT(cpu), 16);
+	outer_clean_range(HB_JUMP_TABLE_PHYS(cpu),
+			  HB_JUMP_TABLE_PHYS(cpu) + 15);
+}
+
+const static struct of_device_id irq_match[] = {
+	{ .compatible = "arm,cortex-a9-gic", .data = gic_of_init, },
+	{}
+};
+
+static void __init highbank_init_irq(void)
+{
+	of_irq_init(irq_match);
+	l2x0_of_init(0, ~0UL);
+}
+
+static void __init highbank_timer_init(void)
+{
+	int irq;
+	struct device_node *np;
+	void __iomem *timer_base;
+
+	/* Map system registers */
+	np = of_find_compatible_node(NULL, NULL, "calxeda,hb-sregs");
+	sregs_base = of_iomap(np, 0);
+	WARN_ON(!sregs_base);
+
+	np = of_find_compatible_node(NULL, NULL, "arm,sp804");
+	timer_base = of_iomap(np, 0);
+	WARN_ON(!timer_base);
+	irq = irq_of_parse_and_map(np, 0);
+
+	highbank_clocks_init();
+
+	sp804_clocksource_init(timer_base + 0x20, "timer1");
+	sp804_clockevents_init(timer_base, irq, "timer0");
+}
+
+static struct sys_timer highbank_timer = {
+	.init = highbank_timer_init,
+};
+
+static void highbank_power_off(void)
+{
+	hignbank_set_pwr_shutdown();
+	scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
+
+	while (1)
+		cpu_do_idle();
+}
+
+static void __init highbank_init(void)
+{
+	pm_power_off = highbank_power_off;
+
+	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+}
+
+static const char *highbank_match[] __initconst = {
+	"calxeda,highbank",
+	NULL,
+};
+
+DT_MACHINE_START(HIGHBANK, "Highbank")
+	.map_io		= highbank_map_io,
+	.init_irq	= highbank_init_irq,
+	.timer		= &highbank_timer,
+	.init_machine	= highbank_init,
+	.dt_compat	= highbank_match,
+MACHINE_END

arch/arm/mach-highbank/hotplug.c

@@ -0,0 +1,56 @@
+/*
+ * Copyright 2011 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/smp.h>
+
+#include <asm/smp_scu.h>
+#include <asm/cacheflush.h>
+
+#include "core.h"
+
+extern void secondary_startup(void);
+
+int platform_cpu_kill(unsigned int cpu)
+{
+	return 1;
+}
+
+/*
+ * platform-specific code to shutdown a CPU
+ *
+ */
+void platform_cpu_die(unsigned int cpu)
+{
+	flush_cache_all();
+
+	highbank_set_cpu_jump(cpu, secondary_startup);
+	scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
+
+	cpu_do_idle();
+
+	/* We should never return from idle */
+	panic("highbank: cpu %d unexpectedly exit from shutdown\n", cpu);
+}
+
+int platform_cpu_disable(unsigned int cpu)
+{
+	/*
+	 * CPU0 should not be shut down via hotplug.  cpu_idle can WFI
+	 * or a proper shutdown or hibernate should be used.
+	 */
+	return cpu == 0 ? -EPERM : 0;
+}

arch/arm/mach-highbank/include/mach/debug-macro.S

@@ -0,0 +1,19 @@
+/*
+ * Debugging macro include header
+ *
+ *  Copyright (C) 1994-1999 Russell King
+ *  Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+		.macro	addruart,rp,rv,tmp
+		movw	\rv, #0x6000
+		movt	\rv, #0xfee3
+		movw	\rp, #0x6000
+		movt	\rp, #0xfff3
+		.endm
+
+#include <asm/hardware/debug-pl01x.S>

arch/arm/mach-highbank/include/mach/entry-macro.S

@@ -0,0 +1,7 @@
+#include <asm/hardware/entry-macro-gic.S>
+
+	.macro	disable_fiq
+	.endm
+
+	.macro	arch_ret_to_user, tmp1, tmp2
+	.endm

arch/arm/mach-highbank/include/mach/gpio.h

@@ -0,0 +1 @@
+/* empty */

arch/arm/mach-highbank/include/mach/io.h

@@ -0,0 +1,7 @@
+#ifndef __MACH_IO_H
+#define __MACH_IO_H
+
+#define __io(a)		({ (void)(a); __typesafe_io(0); })
+#define __mem_pci(a)	(a)
+
+#endif

arch/arm/mach-highbank/include/mach/irqs.h

@@ -0,0 +1,6 @@
+#ifndef __MACH_IRQS_H
+#define __MACH_IRQS_H
+
+#define NR_IRQS			192
+
+#endif

arch/arm/mach-highbank/include/mach/memory.h

@@ -0,0 +1 @@
+/* empty */

arch/arm/mach-highbank/include/mach/system.h

@@ -0,0 +1,26 @@
+/*
+ * Copyright 2010-2011 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#ifndef __MACH_SYSTEM_H
+#define __MACH_SYSTEM_H
+
+static inline void arch_idle(void)
+{
+	cpu_do_idle();
+}
+
+extern void arch_reset(char mode, const char *cmd);
+
+#endif

arch/arm/mach-highbank/include/mach/timex.h

@@ -0,0 +1,6 @@
+#ifndef __MACH_TIMEX_H
+#define __MACH_TIMEX_H
+
+#define CLOCK_TICK_RATE		1000000
+
+#endif

arch/arm/mach-highbank/include/mach/uncompress.h

@@ -0,0 +1,9 @@
+#ifndef __MACH_UNCOMPRESS_H
+#define __MACH_UNCOMPRESS_H
+
+#define putc(c)
+#define flush()
+#define arch_decomp_setup()
+#define arch_decomp_wdog()
+
+#endif

arch/arm/mach-highbank/include/mach/vmalloc.h

@@ -0,0 +1 @@
+#define VMALLOC_END		0xFEE00000UL

arch/arm/mach-highbank/lluart.c

@@ -0,0 +1,34 @@
+/*
+ * Copyright 2011 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/init.h>
+#include <asm/page.h>
+#include <asm/sizes.h>
+#include <asm/mach/map.h>
+
+#define HB_DEBUG_LL_PHYS_BASE	0xfff36000
+#define HB_DEBUG_LL_VIRT_BASE	0xfee36000
+
+static struct map_desc lluart_io_desc __initdata = {
+	.virtual	= HB_DEBUG_LL_VIRT_BASE,
+	.pfn		= __phys_to_pfn(HB_DEBUG_LL_PHYS_BASE),
+	.length		= SZ_4K,
+	.type		= MT_DEVICE,
+};
+
+void __init highbank_lluart_map_io(void)
+{
+	iotable_init(&lluart_io_desc, 1);
+}

arch/arm/mach-highbank/localtimer.c

@@ -0,0 +1,40 @@
+/*
+ * Copyright 2010-2011 Calxeda, Inc.
+ * Based on localtimer.c, Copyright (C) 2002 ARM Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/init.h>
+#include <linux/clockchips.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+
+#include <asm/smp_twd.h>
+
+/*
+ * Setup the local clock events for a CPU.
+ */
+int __cpuinit local_timer_setup(struct clock_event_device *evt)
+{
+	struct device_node *np;
+
+	np = of_find_compatible_node(NULL, NULL, "arm,smp-twd");
+	if (!twd_base) {
+		twd_base = of_iomap(np, 0);
+		WARN_ON(!twd_base);
+	}
+	evt->irq = irq_of_parse_and_map(np, 0);
+	twd_timer_setup(evt);
+	return 0;
+}

arch/arm/mach-highbank/platsmp.c

@@ -0,0 +1,78 @@
+/*
+ * Copyright 2010-2011 Calxeda, Inc.
+ * Based on platsmp.c, Copyright (C) 2002 ARM Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/init.h>
+#include <linux/smp.h>
+#include <linux/io.h>
+
+#include <asm/smp_scu.h>
+#include <asm/hardware/gic.h>
+
+#include "core.h"
+
+extern void secondary_startup(void);
+
+void __cpuinit platform_secondary_init(unsigned int cpu)
+{
+	gic_secondary_init(0);
+}
+
+int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle)
+{
+	gic_raise_softirq(cpumask_of(cpu), 0);
+	return 0;
+}
+
+/*
+ * Initialise the CPU possible map early - this describes the CPUs
+ * which may be present or become present in the system.
+ */
+void __init smp_init_cpus(void)
+{
+	unsigned int i, ncores;
+
+	ncores = scu_get_core_count(scu_base_addr);
+
+	/* sanity check */
+	if (ncores > NR_CPUS) {
+		printk(KERN_WARNING
+		       "highbank: no. of cores (%d) greater than configured "
+		       "maximum of %d - clipping\n",
+		       ncores, NR_CPUS);
+		ncores = NR_CPUS;
+	}
+
+	for (i = 0; i < ncores; i++)
+		set_cpu_possible(i, true);
+
+	set_smp_cross_call(gic_raise_softirq);
+}
+
+void __init platform_smp_prepare_cpus(unsigned int max_cpus)
+{
+	int i;
+
+	scu_enable(scu_base_addr);
+
+	/*
+	 * Write the address of secondary startup into the jump table
+	 * The cores are in wfi and wait until they receive a soft interrupt
+	 * and a non-zero value to jump to. Then the secondary CPU branches
+	 * to this address.
+	 */
+	for (i = 1; i < max_cpus; i++)
+		highbank_set_cpu_jump(i, secondary_startup);
+}

arch/arm/mach-highbank/pm.c

@@ -0,0 +1,55 @@
+/*
+ * Copyright 2011 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/suspend.h>
+
+#include <asm/proc-fns.h>
+#include <asm/smp_scu.h>
+#include <asm/suspend.h>
+
+#include "core.h"
+#include "sysregs.h"
+
+static int highbank_suspend_finish(unsigned long val)
+{
+	cpu_do_idle();
+	return 0;
+}
+
+static int highbank_pm_enter(suspend_state_t state)
+{
+	hignbank_set_pwr_suspend();
+	highbank_set_cpu_jump(0, cpu_resume);
+
+	scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
+	cpu_suspend(0, highbank_suspend_finish);
+
+	return 0;
+}
+
+static const struct platform_suspend_ops highbank_pm_ops = {
+	.enter = highbank_pm_enter,
+	.valid = suspend_valid_only_mem,
+};
+
+static int __init highbank_pm_init(void)
+{
+	suspend_set_ops(&highbank_pm_ops);
+	return 0;
+}
+module_init(highbank_pm_init);

arch/arm/mach-highbank/sysregs.h

@@ -0,0 +1,52 @@
+/*
+ * Copyright 2011 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#ifndef _MACH_HIGHBANK__SYSREGS_H_
+#define _MACH_HIGHBANK__SYSREGS_H_
+
+#include <linux/io.h>
+
+extern void __iomem *sregs_base;
+
+#define HB_SREG_A9_PWR_REQ		0xf00
+#define HB_SREG_A9_BOOT_STAT		0xf04
+#define HB_SREG_A9_BOOT_DATA		0xf08
+
+#define HB_PWR_SUSPEND			0
+#define HB_PWR_SOFT_RESET		1
+#define HB_PWR_HARD_RESET		2
+#define HB_PWR_SHUTDOWN			3
+
+static inline void hignbank_set_pwr_suspend(void)
+{
+	writel(HB_PWR_SUSPEND, sregs_base + HB_SREG_A9_PWR_REQ);
+}
+
+static inline void hignbank_set_pwr_shutdown(void)
+{
+	writel(HB_PWR_SHUTDOWN, sregs_base + HB_SREG_A9_PWR_REQ);
+}
+
+static inline void hignbank_set_pwr_soft_reset(void)
+{
+	writel(HB_PWR_SOFT_RESET, sregs_base + HB_SREG_A9_PWR_REQ);
+}
+
+static inline void hignbank_set_pwr_hard_reset(void)
+{
+	writel(HB_PWR_HARD_RESET, sregs_base + HB_SREG_A9_PWR_REQ);
+}
+
+#endif

arch/arm/mach-highbank/system.c

@@ -0,0 +1,33 @@
+/*
+ * Copyright 2011 Calxeda, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/io.h>
+#include <asm/smp_scu.h>
+#include <asm/proc-fns.h>
+
+#include "core.h"
+#include "sysregs.h"
+
+void arch_reset(char mode, const char *cmd)
+{
+	if (mode == 'h')
+		hignbank_set_pwr_hard_reset();
+	else
+		hignbank_set_pwr_soft_reset();
+
+	scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
+	cpu_do_idle();
+}
+

arch/arm/mach-imx/iomux-imx31.c

@@ -17,13 +17,12 @@
  * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
  * MA 02110-1301, USA.
  */
-
+#include <linux/gpio.h>
 #include <linux/module.h>
 #include <linux/spinlock.h>
 #include <linux/io.h>
 #include <linux/kernel.h>
 #include <mach/hardware.h>
-#include <mach/gpio.h>
 #include <mach/iomux-mx3.h>
 
 /*

arch/arm/mach-imx/mach-mx27ads.c

@@ -13,7 +13,7 @@
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  */
-
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/map.h>
@@ -27,7 +27,6 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/time.h>
 #include <asm/mach/map.h>
-#include <mach/gpio.h>
 #include <mach/iomux-mx27.h>
 
 #include "devices-imx27.h"

arch/arm/mach-integrator/include/mach/io.h

@@ -20,8 +20,6 @@
 #ifndef __ASM_ARM_ARCH_IO_H
 #define __ASM_ARM_ARCH_IO_H
 
-#define IO_SPACE_LIMIT 0xffff
-
 /*
  * WARNING: this has to mirror definitions in platform.h
  */

arch/arm/mach-ixp2000/core.c

@@ -13,7 +13,7 @@
  * License version 2. This program is licensed "as is" without any 
  * warranty of any kind, whether express or implied.
  */
-
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/spinlock.h>
@@ -39,7 +39,7 @@
 #include <asm/mach/time.h>
 #include <asm/mach/irq.h>
 
-#include <mach/gpio.h>
+#include <mach/gpio-ixp2000.h>
 
 static DEFINE_SPINLOCK(ixp2000_slowport_lock);
 static unsigned long ixp2000_slowport_irq_flags;