[POWERPC] Add QE device tree node definition
OF device tree node spec used in QE/8360 support patches. Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Jiang Bo <Tanya.jiang@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
This commit is contained in:
Li Yang
Paul Mackerras
parent
5a3e3b2230
commit
9a1ab883c0
@ -1441,6 +1441,258 @@ platforms are moved over to use the flattened-device-tree model.
|
||||
descriptor-types-mask = <012b0ebf>;
|
||||
};
|
||||
|
||||
h) Board Control and Status (BCSR)
|
||||
|
||||
Required properties:
|
||||
|
||||
- device_type : Should be "board-control"
|
||||
- reg : Offset and length of the register set for the device
|
||||
|
||||
Example:
|
||||
|
||||
bcsr@f8000000 {
|
||||
device_type = "board-control";
|
||||
reg = <f8000000 8000>;
|
||||
};
|
||||
|
||||
i) Freescale QUICC Engine module (QE)
|
||||
This represents qe module that is installed on PowerQUICC II Pro.
|
||||
Hopefully it will merge backward compatibility with CPM/CPM2.
|
||||
Basically, it is a bus of devices, that could act more or less
|
||||
as a complete entity (UCC, USB etc ). All of them should be siblings on
|
||||
the "root" qe node, using the common properties from there.
|
||||
The description below applies to the the qe of MPC8360 and
|
||||
more nodes and properties would be extended in the future.
|
||||
|
||||
i) Root QE device
|
||||
|
||||
Required properties:
|
||||
- device_type : should be "qe";
|
||||
- model : precise model of the QE, Can be "QE", "CPM", or "CPM2"
|
||||
- reg : offset and length of the device registers.
|
||||
- bus-frequency : the clock frequency for QUICC Engine.
|
||||
|
||||
Recommended properties
|
||||
- brg-frequency : the internal clock source frequency for baud-rate
|
||||
generators in Hz.
|
||||
|
||||
Example:
|
||||
qe@e0100000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
#interrupt-cells = <2>;
|
||||
device_type = "qe";
|
||||
model = "QE";
|
||||
ranges = <0 e0100000 00100000>;
|
||||
reg = <e0100000 480>;
|
||||
brg-frequency = <0>;
|
||||
bus-frequency = <179A7B00>;
|
||||
}
|
||||
|
||||
|
||||
ii) SPI (Serial Peripheral Interface)
|
||||
|
||||
Required properties:
|
||||
- device_type : should be "spi".
|
||||
- compatible : should be "fsl_spi".
|
||||
- mode : the spi operation mode, it can be "cpu" or "qe".
|
||||
- reg : Offset and length of the register set for the device
|
||||
- interrupts : <a b> where a is the interrupt number and b is a
|
||||
field that represents an encoding of the sense and level
|
||||
information for the interrupt. This should be encoded based on
|
||||
the information in section 2) depending on the type of interrupt
|
||||
controller you have.
|
||||
- interrupt-parent : the phandle for the interrupt controller that
|
||||
services interrupts for this device.
|
||||
|
||||
Example:
|
||||
spi@4c0 {
|
||||
device_type = "spi";
|
||||
compatible = "fsl_spi";
|
||||
reg = <4c0 40>;
|
||||
interrupts = <82 0>;
|
||||
interrupt-parent = <700>;
|
||||
mode = "cpu";
|
||||
};
|
||||
|
||||
|
||||
iii) USB (Universal Serial Bus Controller)
|
||||
|
||||
Required properties:
|
||||
- device_type : should be "usb".
|
||||
- compatible : could be "qe_udc" or "fhci-hcd".
|
||||
- mode : the could be "host" or "slave".
|
||||
- reg : Offset and length of the register set for the device
|
||||
- interrupts : <a b> where a is the interrupt number and b is a
|
||||
field that represents an encoding of the sense and level
|
||||
information for the interrupt. This should be encoded based on
|
||||
the information in section 2) depending on the type of interrupt
|
||||
controller you have.
|
||||
- interrupt-parent : the phandle for the interrupt controller that
|
||||
services interrupts for this device.
|
||||
|
||||
Example(slave):
|
||||
usb@6c0 {
|
||||
device_type = "usb";
|
||||
compatible = "qe_udc";
|
||||
reg = <6c0 40>;
|
||||
interrupts = <8b 0>;
|
||||
interrupt-parent = <700>;
|
||||
mode = "slave";
|
||||
};
|
||||
|
||||
|
||||
iv) UCC (Unified Communications Controllers)
|
||||
|
||||
Required properties:
|
||||
- device_type : should be "network", "hldc", "uart", "transparent"
|
||||
"bisync" or "atm".
|
||||
- compatible : could be "ucc_geth" or "fsl_atm" and so on.
|
||||
- model : should be "UCC".
|
||||
- device-id : the ucc number(1-8), corresponding to UCCx in UM.
|
||||
- reg : Offset and length of the register set for the device
|
||||
- interrupts : <a b> where a is the interrupt number and b is a
|
||||
field that represents an encoding of the sense and level
|
||||
information for the interrupt. This should be encoded based on
|
||||
the information in section 2) depending on the type of interrupt
|
||||
controller you have.
|
||||
- interrupt-parent : the phandle for the interrupt controller that
|
||||
services interrupts for this device.
|
||||
- pio-handle : The phandle for the Parallel I/O port configuration.
|
||||
- rx-clock : represents the UCC receive clock source.
|
||||
0x00 : clock source is disabled;
|
||||
0x1~0x10 : clock source is BRG1~BRG16 respectively;
|
||||
0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
|
||||
- tx-clock: represents the UCC transmit clock source;
|
||||
0x00 : clock source is disabled;
|
||||
0x1~0x10 : clock source is BRG1~BRG16 respectively;
|
||||
0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
|
||||
|
||||
Required properties for network device_type:
|
||||
- mac-address : list of bytes representing the ethernet address.
|
||||
- phy-handle : The phandle for the PHY connected to this controller.
|
||||
|
||||
Example:
|
||||
ucc@2000 {
|
||||
device_type = "network";
|
||||
compatible = "ucc_geth";
|
||||
model = "UCC";
|
||||
device-id = <1>;
|
||||
reg = <2000 200>;
|
||||
interrupts = <a0 0>;
|
||||
interrupt-parent = <700>;
|
||||
mac-address = [ 00 04 9f 00 23 23 ];
|
||||
rx-clock = "none";
|
||||
tx-clock = "clk9";
|
||||
phy-handle = <212000>;
|
||||
pio-handle = <140001>;
|
||||
};
|
||||
|
||||
|
||||
v) Parallel I/O Ports
|
||||
|
||||
This node configures Parallel I/O ports for CPUs with QE support.
|
||||
The node should reside in the "soc" node of the tree. For each
|
||||
device that using parallel I/O ports, a child node should be created.
|
||||
See the definition of the Pin configuration nodes below for more
|
||||
information.
|
||||
|
||||
Required properties:
|
||||
- device_type : should be "par_io".
|
||||
- reg : offset to the register set and its length.
|
||||
- num-ports : number of Parallel I/O ports
|
||||
|
||||
Example:
|
||||
par_io@1400 {
|
||||
reg = <1400 100>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
device_type = "par_io";
|
||||
num-ports = <7>;
|
||||
ucc_pin@01 {
|
||||
......
|
||||
};
|
||||
|
||||
|
||||
vi) Pin configuration nodes
|
||||
|
||||
Required properties:
|
||||
- linux,phandle : phandle of this node; likely referenced by a QE
|
||||
device.
|
||||
- pio-map : array of pin configurations. Each pin is defined by 6
|
||||
integers. The six numbers are respectively: port, pin, dir,
|
||||
open_drain, assignment, has_irq.
|
||||
- port : port number of the pin; 0-6 represent port A-G in UM.
|
||||
- pin : pin number in the port.
|
||||
- dir : direction of the pin, should encode as follows:
|
||||
|
||||
0 = The pin is disabled
|
||||
1 = The pin is an output
|
||||
2 = The pin is an input
|
||||
3 = The pin is I/O
|
||||
|
||||
- open_drain : indicates the pin is normal or wired-OR:
|
||||
|
||||
0 = The pin is actively driven as an output
|
||||
1 = The pin is an open-drain driver. As an output, the pin is
|
||||
driven active-low, otherwise it is three-stated.
|
||||
|
||||
- assignment : function number of the pin according to the Pin Assignment
|
||||
tables in User Manual. Each pin can have up to 4 possible functions in
|
||||
QE and two options for CPM.
|
||||
- has_irq : indicates if the pin is used as source of exteral
|
||||
interrupts.
|
||||
|
||||
Example:
|
||||
ucc_pin@01 {
|
||||
linux,phandle = <140001>;
|
||||
pio-map = <
|
||||
/* port pin dir open_drain assignment has_irq */
|
||||
0 3 1 0 1 0 /* TxD0 */
|
||||
0 4 1 0 1 0 /* TxD1 */
|
||||
0 5 1 0 1 0 /* TxD2 */
|
||||
0 6 1 0 1 0 /* TxD3 */
|
||||
1 6 1 0 3 0 /* TxD4 */
|
||||
1 7 1 0 1 0 /* TxD5 */
|
||||
1 9 1 0 2 0 /* TxD6 */
|
||||
1 a 1 0 2 0 /* TxD7 */
|
||||
0 9 2 0 1 0 /* RxD0 */
|
||||
0 a 2 0 1 0 /* RxD1 */
|
||||
0 b 2 0 1 0 /* RxD2 */
|
||||
0 c 2 0 1 0 /* RxD3 */
|
||||
0 d 2 0 1 0 /* RxD4 */
|
||||
1 1 2 0 2 0 /* RxD5 */
|
||||
1 0 2 0 2 0 /* RxD6 */
|
||||
1 4 2 0 2 0 /* RxD7 */
|
||||
0 7 1 0 1 0 /* TX_EN */
|
||||
0 8 1 0 1 0 /* TX_ER */
|
||||
0 f 2 0 1 0 /* RX_DV */
|
||||
0 10 2 0 1 0 /* RX_ER */
|
||||
0 0 2 0 1 0 /* RX_CLK */
|
||||
2 9 1 0 3 0 /* GTX_CLK - CLK10 */
|
||||
2 8 2 0 1 0>; /* GTX125 - CLK9 */
|
||||
};
|
||||
|
||||
vii) Multi-User RAM (MURAM)
|
||||
|
||||
Required properties:
|
||||
- device_type : should be "muram".
|
||||
- mode : the could be "host" or "slave".
|
||||
- ranges : Should be defined as specified in 1) to describe the
|
||||
translation of MURAM addresses.
|
||||
- data-only : sub-node which defines the address area under MURAM
|
||||
bus that can be allocated as data/parameter
|
||||
|
||||
Example:
|
||||
|
||||
muram@10000 {
|
||||
device_type = "muram";
|
||||
ranges = <0 00010000 0000c000>;
|
||||
|
||||
data-only@0{
|
||||
reg = <0 c000>;
|
||||
};
|
||||
};
|
||||
|
||||
More devices will be defined as this spec matures.
|
||||
|
||||
|
||||
Loading…
Reference in New Issue
Block a user