usb: phy: move all PHY drivers to drivers/usb/phy/
that's a much more reasonable location for those drivers. It helps us saving drivers/usb/otg/ for when we actually start adding generic OTG code. Also completely delete drivers/usb/otg/ as there's nothing left there. Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit is contained in:
Felipe Balbi
parent
110ff6d041
commit
a0e631235a
@ -186,6 +186,4 @@ source "drivers/usb/atm/Kconfig"
|
||||
|
||||
source "drivers/usb/gadget/Kconfig"
|
||||
|
||||
source "drivers/usb/otg/Kconfig"
|
||||
|
||||
endif # USB_SUPPORT
|
||||
|
||||
@ -6,8 +6,6 @@
|
||||
|
||||
obj-$(CONFIG_USB) += core/
|
||||
|
||||
obj-$(CONFIG_USB_OTG_UTILS) += otg/
|
||||
|
||||
obj-$(CONFIG_USB_DWC3) += dwc3/
|
||||
|
||||
obj-$(CONFIG_USB_MON) += mon/
|
||||
|
||||
@ -1,141 +0,0 @@
|
||||
#
|
||||
# USB OTG infrastructure may be needed for peripheral-only, host-only,
|
||||
# or OTG-capable configurations when OTG transceivers or controllers
|
||||
# are used.
|
||||
#
|
||||
|
||||
comment "OTG and related infrastructure"
|
||||
|
||||
config USB_OTG_UTILS
|
||||
bool
|
||||
help
|
||||
Select this to make sure the build includes objects from
|
||||
the OTG infrastructure directory.
|
||||
|
||||
if USB || USB_GADGET
|
||||
|
||||
#
|
||||
# USB Transceiver Drivers
|
||||
#
|
||||
config USB_GPIO_VBUS
|
||||
tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
|
||||
depends on GENERIC_GPIO
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Provides simple GPIO VBUS sensing for controllers with an
|
||||
internal transceiver via the usb_phy interface, and
|
||||
optionally control of a D+ pullup GPIO as well as a VBUS
|
||||
current limit regulator.
|
||||
|
||||
config ISP1301_OMAP
|
||||
tristate "Philips ISP1301 with OMAP OTG"
|
||||
depends on I2C && ARCH_OMAP_OTG
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
If you say yes here you get support for the Philips ISP1301
|
||||
USB-On-The-Go transceiver working with the OMAP OTG controller.
|
||||
The ISP1301 is a full speed USB transceiver which is used in
|
||||
products including H2, H3, and H4 development boards for Texas
|
||||
Instruments OMAP processors.
|
||||
|
||||
This driver can also be built as a module. If so, the module
|
||||
will be called isp1301_omap.
|
||||
|
||||
config USB_ULPI
|
||||
bool "Generic ULPI Transceiver Driver"
|
||||
depends on ARM
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Enable this to support ULPI connected USB OTG transceivers which
|
||||
are likely found on embedded boards.
|
||||
|
||||
config USB_ULPI_VIEWPORT
|
||||
bool
|
||||
depends on USB_ULPI
|
||||
help
|
||||
Provides read/write operations to the ULPI phy register set for
|
||||
controllers with a viewport register (e.g. Chipidea/ARC controllers).
|
||||
|
||||
config TWL4030_USB
|
||||
tristate "TWL4030 USB Transceiver Driver"
|
||||
depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Enable this to support the USB OTG transceiver on TWL4030
|
||||
family chips (including the TWL5030 and TPS659x0 devices).
|
||||
This transceiver supports high and full speed devices plus,
|
||||
in host mode, low speed.
|
||||
|
||||
config TWL6030_USB
|
||||
tristate "TWL6030 USB Transceiver Driver"
|
||||
depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Enable this to support the USB OTG transceiver on TWL6030
|
||||
family chips. This TWL6030 transceiver has the VBUS and ID GND
|
||||
and OTG SRP events capabilities. For all other transceiver functionality
|
||||
UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
|
||||
are hooked to this driver through platform_data structure.
|
||||
The definition of internal PHY APIs are in the mach-omap2 layer.
|
||||
|
||||
config NOP_USB_XCEIV
|
||||
tristate "NOP USB Transceiver Driver"
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
This driver is to be used by all the usb transceiver which are either
|
||||
built-in with usb ip or which are autonomous and doesn't require any
|
||||
phy programming such as ISP1x04 etc.
|
||||
|
||||
config USB_MSM_OTG
|
||||
tristate "OTG support for Qualcomm on-chip USB controller"
|
||||
depends on (USB || USB_GADGET) && ARCH_MSM
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Enable this to support the USB OTG transceiver on MSM chips. It
|
||||
handles PHY initialization, clock management, and workarounds
|
||||
required after resetting the hardware and power management.
|
||||
This driver is required even for peripheral only or host only
|
||||
mode configurations.
|
||||
This driver is not supported on boards like trout which
|
||||
has an external PHY.
|
||||
|
||||
config AB8500_USB
|
||||
tristate "AB8500 USB Transceiver Driver"
|
||||
depends on AB8500_CORE
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Enable this to support the USB OTG transceiver in AB8500 chip.
|
||||
This transceiver supports high and full speed devices plus,
|
||||
in host mode, low speed.
|
||||
|
||||
config FSL_USB2_OTG
|
||||
bool "Freescale USB OTG Transceiver Driver"
|
||||
depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_SUSPEND
|
||||
select USB_OTG
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Enable this to support Freescale USB OTG transceiver.
|
||||
|
||||
config USB_MXS_PHY
|
||||
tristate "Freescale MXS USB PHY support"
|
||||
depends on ARCH_MXC || ARCH_MXS
|
||||
select STMP_DEVICE
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Enable this to support the Freescale MXS USB PHY.
|
||||
|
||||
MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
|
||||
|
||||
config USB_MV_OTG
|
||||
tristate "Marvell USB OTG support"
|
||||
depends on USB_EHCI_MV && USB_MV_UDC && USB_SUSPEND
|
||||
select USB_OTG
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Say Y here if you want to build Marvell USB OTG transciever
|
||||
driver in kernel (including PXA and MMP series). This driver
|
||||
implements role switch between EHCI host driver and gadget driver.
|
||||
|
||||
To compile this driver as a module, choose M here.
|
||||
|
||||
endif # USB || OTG
|
||||
@ -1,21 +0,0 @@
|
||||
#
|
||||
# OTG infrastructure and transceiver drivers
|
||||
#
|
||||
|
||||
ccflags-$(CONFIG_USB_DEBUG) := -DDEBUG
|
||||
ccflags-$(CONFIG_USB_GADGET_DEBUG) += -DDEBUG
|
||||
|
||||
# transceiver drivers
|
||||
obj-$(CONFIG_USB_GPIO_VBUS) += gpio_vbus.o
|
||||
obj-$(CONFIG_ISP1301_OMAP) += isp1301_omap.o
|
||||
obj-$(CONFIG_TWL4030_USB) += twl4030-usb.o
|
||||
obj-$(CONFIG_TWL6030_USB) += twl6030-usb.o
|
||||
obj-$(CONFIG_NOP_USB_XCEIV) += nop-usb-xceiv.o
|
||||
obj-$(CONFIG_USB_ULPI) += ulpi.o
|
||||
obj-$(CONFIG_USB_ULPI_VIEWPORT) += ulpi_viewport.o
|
||||
obj-$(CONFIG_USB_MSM_OTG) += msm_otg.o
|
||||
obj-$(CONFIG_AB8500_USB) += ab8500-usb.o
|
||||
fsl_usb2_otg-objs := fsl_otg.o otg_fsm.o
|
||||
obj-$(CONFIG_FSL_USB2_OTG) += fsl_usb2_otg.o
|
||||
obj-$(CONFIG_USB_MXS_PHY) += mxs-phy.o
|
||||
obj-$(CONFIG_USB_MV_OTG) += mv_otg.o
|
||||
@ -4,6 +4,73 @@
|
||||
comment "USB Physical Layer drivers"
|
||||
depends on USB || USB_GADGET
|
||||
|
||||
config USB_OTG_UTILS
|
||||
bool
|
||||
help
|
||||
Select this to make sure the build includes objects from
|
||||
the OTG infrastructure directory.
|
||||
|
||||
if USB || USB_GADGET
|
||||
|
||||
#
|
||||
# USB Transceiver Drivers
|
||||
#
|
||||
config AB8500_USB
|
||||
tristate "AB8500 USB Transceiver Driver"
|
||||
depends on AB8500_CORE
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Enable this to support the USB OTG transceiver in AB8500 chip.
|
||||
This transceiver supports high and full speed devices plus,
|
||||
in host mode, low speed.
|
||||
|
||||
config FSL_USB2_OTG
|
||||
bool "Freescale USB OTG Transceiver Driver"
|
||||
depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_SUSPEND
|
||||
select USB_OTG
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Enable this to support Freescale USB OTG transceiver.
|
||||
|
||||
config ISP1301_OMAP
|
||||
tristate "Philips ISP1301 with OMAP OTG"
|
||||
depends on I2C && ARCH_OMAP_OTG
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
If you say yes here you get support for the Philips ISP1301
|
||||
USB-On-The-Go transceiver working with the OMAP OTG controller.
|
||||
The ISP1301 is a full speed USB transceiver which is used in
|
||||
products including H2, H3, and H4 development boards for Texas
|
||||
Instruments OMAP processors.
|
||||
|
||||
This driver can also be built as a module. If so, the module
|
||||
will be called isp1301_omap.
|
||||
|
||||
config MV_U3D_PHY
|
||||
bool "Marvell USB 3.0 PHY controller Driver"
|
||||
depends on USB_MV_U3D
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Enable this to support Marvell USB 3.0 phy controller for Marvell
|
||||
SoC.
|
||||
|
||||
config NOP_USB_XCEIV
|
||||
tristate "NOP USB Transceiver Driver"
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
This driver is to be used by all the usb transceiver which are either
|
||||
built-in with usb ip or which are autonomous and doesn't require any
|
||||
phy programming such as ISP1x04 etc.
|
||||
|
||||
config OMAP_CONTROL_USB
|
||||
tristate "OMAP CONTROL USB Driver"
|
||||
help
|
||||
Enable this to add support for the USB part present in the control
|
||||
module. This driver has API to power on the USB2 PHY and to write to
|
||||
the mailbox. The mailbox is present only in omap4 and the register to
|
||||
power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an
|
||||
additional register to power on USB3 PHY.
|
||||
|
||||
config OMAP_USB2
|
||||
tristate "OMAP USB2 PHY Driver"
|
||||
depends on ARCH_OMAP2PLUS
|
||||
@ -25,14 +92,45 @@ config OMAP_USB3
|
||||
This driver interacts with the "OMAP Control USB Driver" to power
|
||||
on/off the PHY.
|
||||
|
||||
config OMAP_CONTROL_USB
|
||||
tristate "OMAP CONTROL USB Driver"
|
||||
config SAMSUNG_USBPHY
|
||||
bool "Samsung USB PHY controller Driver"
|
||||
depends on USB_S3C_HSOTG || USB_EHCI_S5P || USB_OHCI_EXYNOS
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Enable this to add support for the USB part present in the control
|
||||
module. This driver has API to power on the USB2 PHY and to write to
|
||||
the mailbox. The mailbox is present only in omap4 and the register to
|
||||
power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an
|
||||
additional register to power on USB3 PHY.
|
||||
Enable this to support Samsung USB phy controller for samsung
|
||||
SoCs.
|
||||
|
||||
config TWL4030_USB
|
||||
tristate "TWL4030 USB Transceiver Driver"
|
||||
depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Enable this to support the USB OTG transceiver on TWL4030
|
||||
family chips (including the TWL5030 and TPS659x0 devices).
|
||||
This transceiver supports high and full speed devices plus,
|
||||
in host mode, low speed.
|
||||
|
||||
config TWL6030_USB
|
||||
tristate "TWL6030 USB Transceiver Driver"
|
||||
depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Enable this to support the USB OTG transceiver on TWL6030
|
||||
family chips. This TWL6030 transceiver has the VBUS and ID GND
|
||||
and OTG SRP events capabilities. For all other transceiver functionality
|
||||
UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
|
||||
are hooked to this driver through platform_data structure.
|
||||
The definition of internal PHY APIs are in the mach-omap2 layer.
|
||||
|
||||
config USB_GPIO_VBUS
|
||||
tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
|
||||
depends on GENERIC_GPIO
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Provides simple GPIO VBUS sensing for controllers with an
|
||||
internal transceiver via the usb_phy interface, and
|
||||
optionally control of a D+ pullup GPIO as well as a VBUS
|
||||
current limit regulator.
|
||||
|
||||
config USB_ISP1301
|
||||
tristate "NXP ISP1301 USB transceiver support"
|
||||
@ -46,13 +144,40 @@ config USB_ISP1301
|
||||
To compile this driver as a module, choose M here: the
|
||||
module will be called isp1301.
|
||||
|
||||
config MV_U3D_PHY
|
||||
bool "Marvell USB 3.0 PHY controller Driver"
|
||||
depends on USB_MV_U3D
|
||||
config USB_MSM_OTG
|
||||
tristate "OTG support for Qualcomm on-chip USB controller"
|
||||
depends on (USB || USB_GADGET) && ARCH_MSM
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Enable this to support Marvell USB 3.0 phy controller for Marvell
|
||||
SoC.
|
||||
Enable this to support the USB OTG transceiver on MSM chips. It
|
||||
handles PHY initialization, clock management, and workarounds
|
||||
required after resetting the hardware and power management.
|
||||
This driver is required even for peripheral only or host only
|
||||
mode configurations.
|
||||
This driver is not supported on boards like trout which
|
||||
has an external PHY.
|
||||
|
||||
config USB_MV_OTG
|
||||
tristate "Marvell USB OTG support"
|
||||
depends on USB_EHCI_MV && USB_MV_UDC && USB_SUSPEND
|
||||
select USB_OTG
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Say Y here if you want to build Marvell USB OTG transciever
|
||||
driver in kernel (including PXA and MMP series). This driver
|
||||
implements role switch between EHCI host driver and gadget driver.
|
||||
|
||||
To compile this driver as a module, choose M here.
|
||||
|
||||
config USB_MXS_PHY
|
||||
tristate "Freescale MXS USB PHY support"
|
||||
depends on ARCH_MXC || ARCH_MXS
|
||||
select STMP_DEVICE
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Enable this to support the Freescale MXS USB PHY.
|
||||
|
||||
MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
|
||||
|
||||
config USB_RCAR_PHY
|
||||
tristate "Renesas R-Car USB phy support"
|
||||
@ -66,10 +191,19 @@ config USB_RCAR_PHY
|
||||
To compile this driver as a module, choose M here: the
|
||||
module will be called rcar-phy.
|
||||
|
||||
config SAMSUNG_USBPHY
|
||||
bool "Samsung USB PHY controller Driver"
|
||||
depends on USB_S3C_HSOTG || USB_EHCI_S5P || USB_OHCI_EXYNOS
|
||||
config USB_ULPI
|
||||
bool "Generic ULPI Transceiver Driver"
|
||||
depends on ARM
|
||||
select USB_OTG_UTILS
|
||||
help
|
||||
Enable this to support Samsung USB phy controller for samsung
|
||||
SoCs.
|
||||
Enable this to support ULPI connected USB OTG transceivers which
|
||||
are likely found on embedded boards.
|
||||
|
||||
config USB_ULPI_VIEWPORT
|
||||
bool
|
||||
depends on USB_ULPI
|
||||
help
|
||||
Provides read/write operations to the ULPI phy register set for
|
||||
controllers with a viewport register (e.g. Chipidea/ARC controllers).
|
||||
|
||||
endif # USB || OTG
|
||||
|
||||
@ -5,11 +5,27 @@
|
||||
ccflags-$(CONFIG_USB_DEBUG) := -DDEBUG
|
||||
|
||||
obj-$(CONFIG_USB_OTG_UTILS) += phy.o
|
||||
|
||||
# transceiver drivers, keep the list sorted
|
||||
|
||||
obj-$(CONFIG_AB8500_USB) += ab8500-usb.o
|
||||
fsl_usb2_otg-objs := fsl_otg.o otg_fsm.o
|
||||
obj-$(CONFIG_FSL_USB2_OTG) += fsl_usb2_otg.o
|
||||
obj-$(CONFIG_ISP1301_OMAP) += isp1301_omap.o
|
||||
obj-$(CONFIG_MV_U3D_PHY) += mv_u3d_phy.o
|
||||
obj-$(CONFIG_NOP_USB_XCEIV) += nop-usb-xceiv.o
|
||||
obj-$(CONFIG_OMAP_CONTROL_USB) += omap-control-usb.o
|
||||
obj-$(CONFIG_OMAP_USB2) += omap-usb2.o
|
||||
obj-$(CONFIG_OMAP_USB3) += omap-usb3.o
|
||||
obj-$(CONFIG_OMAP_CONTROL_USB) += omap-control-usb.o
|
||||
obj-$(CONFIG_USB_ISP1301) += isp1301.o
|
||||
obj-$(CONFIG_MV_U3D_PHY) += mv_u3d_phy.o
|
||||
obj-$(CONFIG_USB_EHCI_TEGRA) += tegra_usb_phy.o
|
||||
obj-$(CONFIG_USB_RCAR_PHY) += rcar-phy.o
|
||||
obj-$(CONFIG_SAMSUNG_USBPHY) += samsung-usbphy.o
|
||||
obj-$(CONFIG_TWL4030_USB) += twl4030-usb.o
|
||||
obj-$(CONFIG_TWL6030_USB) += twl6030-usb.o
|
||||
obj-$(CONFIG_USB_EHCI_TEGRA) += tegra_usb_phy.o
|
||||
obj-$(CONFIG_USB_GPIO_VBUS) += gpio_vbus.o
|
||||
obj-$(CONFIG_USB_ISP1301) += isp1301.o
|
||||
obj-$(CONFIG_USB_MSM_OTG) += msm_otg.o
|
||||
obj-$(CONFIG_USB_MV_OTG) += mv_otg.o
|
||||
obj-$(CONFIG_USB_MXS_PHY) += mxs-phy.o
|
||||
obj-$(CONFIG_USB_RCAR_PHY) += rcar-phy.o
|
||||
obj-$(CONFIG_USB_ULPI) += ulpi.o
|
||||
obj-$(CONFIG_USB_ULPI_VIEWPORT) += ulpi_viewport.o
|
||||
|
||||
Loading…
Reference in New Issue
Block a user