From 6f6bbc186dc8e4e0c628db7decbd1a5e02cb5fd8 Mon Sep 17 00:00:00 2001 From: Jesse Brandeburg Date: Thu, 26 Jul 2012 02:30:53 +0000 Subject: [PATCH 1/6] ethtool.h: MDI setting support This change modifies the core ethtool struct to allow a driver to support setting of MDI/MDI-X state for twisted pair wiring. This change uses a previously reserved u8 and should not change any binary compatibility of ethtool. Also as per Ben Hutchings' suggestion, the capabilities are stored in a separate byte so the driver can report if it supports changing settings. see thread: http://kerneltrap.org/mailarchive/linux-netdev/2010/11/17/6289820/thread see ethtool patches titled: ethtool: allow setting MDI-X state Signed-off-by: Jesse Brandeburg CC: Ben Hutchings Tested-by: Aaron Brown aaron.f.brown@intel.com Signed-off-by: Jeff Kirsher --- include/linux/ethtool.h | 17 +++++++++++------ 1 file changed, 11 insertions(+), 6 deletions(-) diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h index 21eff418091b..fcb4f8e60c1c 100644 --- a/include/linux/ethtool.h +++ b/include/linux/ethtool.h @@ -45,8 +45,10 @@ struct ethtool_cmd { * bits) in Mbps. Please use * ethtool_cmd_speed()/_set() to * access it */ - __u8 eth_tp_mdix; - __u8 reserved2; + __u8 eth_tp_mdix; /* twisted pair MDI-X status */ + __u8 eth_tp_mdix_ctrl; /* twisted pair MDI-X control, when set, + * link should be renegotiated if necessary + */ __u32 lp_advertising; /* Features the link partner advertises */ __u32 reserved[2]; }; @@ -1229,10 +1231,13 @@ struct ethtool_ops { #define AUTONEG_DISABLE 0x00 #define AUTONEG_ENABLE 0x01 -/* Mode MDI or MDI-X */ -#define ETH_TP_MDI_INVALID 0x00 -#define ETH_TP_MDI 0x01 -#define ETH_TP_MDI_X 0x02 +/* MDI or MDI-X status/control - if MDI/MDI_X/AUTO is set then + * the driver is required to renegotiate link + */ +#define ETH_TP_MDI_INVALID 0x00 /* status: unknown; control: unsupported */ +#define ETH_TP_MDI 0x01 /* status: MDI; control: force MDI */ +#define ETH_TP_MDI_X 0x02 /* status: MDI-X; control: force MDI-X */ +#define ETH_TP_MDI_AUTO 0x03 /* control: auto-select */ /* Wake-On-Lan options. */ #define WAKE_PHY (1 << 0) From e86fd89188abcc3288ca760a064000054110b2bb Mon Sep 17 00:00:00 2001 From: Bruce W Allan Date: Thu, 26 Jul 2012 02:30:59 +0000 Subject: [PATCH 2/6] e1000e: implement 82577/579 MDI setting support In order for e1000e to support MDI setting support via ethtool this code is needed to allow setting the MDI state via software. This is in regards to the related ethtool patch and fixes bugzilla.kernel.org bug 11998 Signed-off-by: Bruce W Allan Signed-off-by: Jesse Brandeburg Tested-by: Aaron Brown aaron.f.brown@intel.com Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/e1000e/phy.c | 31 +++++++++++++++++++++++-- 1 file changed, 29 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c index b860d4f7ea2a..fc62a3f3a5be 100644 --- a/drivers/net/ethernet/intel/e1000e/phy.c +++ b/drivers/net/ethernet/intel/e1000e/phy.c @@ -84,8 +84,9 @@ static const u16 e1000_igp_2_cable_length_table[] = { #define I82577_PHY_STATUS2_SPEED_1000MBPS 0x0200 /* I82577 PHY Control 2 */ -#define I82577_PHY_CTRL2_AUTO_MDIX 0x0400 -#define I82577_PHY_CTRL2_FORCE_MDI_MDIX 0x0200 +#define I82577_PHY_CTRL2_MANUAL_MDIX 0x0200 +#define I82577_PHY_CTRL2_AUTO_MDI_MDIX 0x0400 +#define I82577_PHY_CTRL2_MDIX_CFG_MASK 0x0600 /* I82577 PHY Diagnostics Status */ #define I82577_DSTATUS_CABLE_LENGTH 0x03FC @@ -702,6 +703,32 @@ s32 e1000_copper_link_setup_82577(struct e1000_hw *hw) if (ret_val) return ret_val; + /* Set MDI/MDIX mode */ + ret_val = e1e_rphy(hw, I82577_PHY_CTRL_2, &phy_data); + if (ret_val) + return ret_val; + phy_data &= ~I82577_PHY_CTRL2_MDIX_CFG_MASK; + /* + * Options: + * 0 - Auto (default) + * 1 - MDI mode + * 2 - MDI-X mode + */ + switch (hw->phy.mdix) { + case 1: + break; + case 2: + phy_data |= I82577_PHY_CTRL2_MANUAL_MDIX; + break; + case 0: + default: + phy_data |= I82577_PHY_CTRL2_AUTO_MDI_MDIX; + break; + } + ret_val = e1e_wphy(hw, I82577_PHY_CTRL_2, phy_data); + if (ret_val) + return ret_val; + return e1000_set_master_slave_mode(hw); } From 1b556783abe92d3bfedf0d0eb3af2319947739ae Mon Sep 17 00:00:00 2001 From: Jesse Brandeburg Date: Thu, 26 Jul 2012 02:31:04 +0000 Subject: [PATCH 3/6] igb: implement 580 MDI setting support In order for igb to support MDI setting support via ethtool this code is needed to allow setting the MDI state via software. This is in regards to the related ethtool patch Signed-off-by: Jesse Brandeburg Tested-by: Aaron Brown aaron.f.brown@intel.com Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/igb/e1000_phy.c | 29 ++++++++++++++++++++-- drivers/net/ethernet/intel/igb/e1000_phy.h | 5 ++-- 2 files changed, 30 insertions(+), 4 deletions(-) diff --git a/drivers/net/ethernet/intel/igb/e1000_phy.c b/drivers/net/ethernet/intel/igb/e1000_phy.c index 7be98b6f1052..3404bc79f4ca 100644 --- a/drivers/net/ethernet/intel/igb/e1000_phy.c +++ b/drivers/net/ethernet/intel/igb/e1000_phy.c @@ -464,6 +464,32 @@ s32 igb_copper_link_setup_82580(struct e1000_hw *hw) phy_data |= I82580_CFG_ENABLE_DOWNSHIFT; ret_val = phy->ops.write_reg(hw, I82580_CFG_REG, phy_data); + if (ret_val) + goto out; + + /* Set MDI/MDIX mode */ + ret_val = phy->ops.read_reg(hw, I82580_PHY_CTRL_2, &phy_data); + if (ret_val) + goto out; + phy_data &= ~I82580_PHY_CTRL2_MDIX_CFG_MASK; + /* + * Options: + * 0 - Auto (default) + * 1 - MDI mode + * 2 - MDI-X mode + */ + switch (hw->phy.mdix) { + case 1: + break; + case 2: + phy_data |= I82580_PHY_CTRL2_MANUAL_MDIX; + break; + case 0: + default: + phy_data |= I82580_PHY_CTRL2_AUTO_MDI_MDIX; + break; + } + ret_val = hw->phy.ops.write_reg(hw, I82580_PHY_CTRL_2, phy_data); out: return ret_val; @@ -2246,8 +2272,7 @@ s32 igb_phy_force_speed_duplex_82580(struct e1000_hw *hw) if (ret_val) goto out; - phy_data &= ~I82580_PHY_CTRL2_AUTO_MDIX; - phy_data &= ~I82580_PHY_CTRL2_FORCE_MDI_MDIX; + phy_data &= ~I82580_PHY_CTRL2_MDIX_CFG_MASK; ret_val = phy->ops.write_reg(hw, I82580_PHY_CTRL_2, phy_data); if (ret_val) diff --git a/drivers/net/ethernet/intel/igb/e1000_phy.h b/drivers/net/ethernet/intel/igb/e1000_phy.h index 34e40619f16b..6ac3299bfcb9 100644 --- a/drivers/net/ethernet/intel/igb/e1000_phy.h +++ b/drivers/net/ethernet/intel/igb/e1000_phy.h @@ -111,8 +111,9 @@ s32 igb_check_polarity_m88(struct e1000_hw *hw); #define I82580_PHY_STATUS2_SPEED_100MBPS 0x0100 /* I82580 PHY Control 2 */ -#define I82580_PHY_CTRL2_AUTO_MDIX 0x0400 -#define I82580_PHY_CTRL2_FORCE_MDI_MDIX 0x0200 +#define I82580_PHY_CTRL2_MANUAL_MDIX 0x0200 +#define I82580_PHY_CTRL2_AUTO_MDI_MDIX 0x0400 +#define I82580_PHY_CTRL2_MDIX_CFG_MASK 0x0600 /* I82580 PHY Diagnostics Status */ #define I82580_DSTATUS_CABLE_LENGTH 0x03FC From c819bbd5eca29aa0d4f35612b7c795c23d38efc3 Mon Sep 17 00:00:00 2001 From: Jesse Brandeburg Date: Thu, 26 Jul 2012 02:31:09 +0000 Subject: [PATCH 4/6] e1000: configure and read MDI settings This is the implementation in e1000 to allow ethtool to force MDI state, allowing users to work around some improperly behaving switches. Forcing in this driver is for now only allowed when auto-neg is enabled. To use must have the matching version of ethtool app that supports this functionality. Signed-off-by: Jesse Brandeburg CC: Tushar Dave Tested-by: Aaron Brown aaron.f.brown@intel.com Signed-off-by: Jeff Kirsher --- .../net/ethernet/intel/e1000/e1000_ethtool.c | 39 +++++++++++++++++++ drivers/net/ethernet/intel/e1000/e1000_main.c | 4 ++ 2 files changed, 43 insertions(+) diff --git a/drivers/net/ethernet/intel/e1000/e1000_ethtool.c b/drivers/net/ethernet/intel/e1000/e1000_ethtool.c index 736a7d987db5..9089d00f1421 100644 --- a/drivers/net/ethernet/intel/e1000/e1000_ethtool.c +++ b/drivers/net/ethernet/intel/e1000/e1000_ethtool.c @@ -174,6 +174,20 @@ static int e1000_get_settings(struct net_device *netdev, ecmd->autoneg = ((hw->media_type == e1000_media_type_fiber) || hw->autoneg) ? AUTONEG_ENABLE : AUTONEG_DISABLE; + + /* MDI-X => 1; MDI => 0 */ + if ((hw->media_type == e1000_media_type_copper) && + netif_carrier_ok(netdev)) + ecmd->eth_tp_mdix = (!!adapter->phy_info.mdix_mode ? + ETH_TP_MDI_X : + ETH_TP_MDI); + else + ecmd->eth_tp_mdix = ETH_TP_MDI_INVALID; + + if (hw->mdix == AUTO_ALL_MODES) + ecmd->eth_tp_mdix_ctrl = ETH_TP_MDI_AUTO; + else + ecmd->eth_tp_mdix_ctrl = hw->mdix; return 0; } @@ -183,6 +197,22 @@ static int e1000_set_settings(struct net_device *netdev, struct e1000_adapter *adapter = netdev_priv(netdev); struct e1000_hw *hw = &adapter->hw; + /* + * MDI setting is only allowed when autoneg enabled because + * some hardware doesn't allow MDI setting when speed or + * duplex is forced. + */ + if (ecmd->eth_tp_mdix_ctrl) { + if (hw->media_type != e1000_media_type_copper) + return -EOPNOTSUPP; + + if ((ecmd->eth_tp_mdix_ctrl != ETH_TP_MDI_AUTO) && + (ecmd->autoneg != AUTONEG_ENABLE)) { + e_err(drv, "forcing MDI/MDI-X state is not supported when link speed and/or duplex are forced\n"); + return -EINVAL; + } + } + while (test_and_set_bit(__E1000_RESETTING, &adapter->flags)) msleep(1); @@ -199,12 +229,21 @@ static int e1000_set_settings(struct net_device *netdev, ecmd->advertising = hw->autoneg_advertised; } else { u32 speed = ethtool_cmd_speed(ecmd); + /* calling this overrides forced MDI setting */ if (e1000_set_spd_dplx(adapter, speed, ecmd->duplex)) { clear_bit(__E1000_RESETTING, &adapter->flags); return -EINVAL; } } + /* MDI-X => 2; MDI => 1; Auto => 3 */ + if (ecmd->eth_tp_mdix_ctrl) { + if (ecmd->eth_tp_mdix_ctrl == ETH_TP_MDI_AUTO) + hw->mdix = AUTO_ALL_MODES; + else + hw->mdix = ecmd->eth_tp_mdix_ctrl; + } + /* reset the link */ if (netif_running(adapter->netdev)) { diff --git a/drivers/net/ethernet/intel/e1000/e1000_main.c b/drivers/net/ethernet/intel/e1000/e1000_main.c index 3bfbb8df8989..0ae2fcfa5124 100644 --- a/drivers/net/ethernet/intel/e1000/e1000_main.c +++ b/drivers/net/ethernet/intel/e1000/e1000_main.c @@ -4939,6 +4939,10 @@ int e1000_set_spd_dplx(struct e1000_adapter *adapter, u32 spd, u8 dplx) default: goto err_inval; } + + /* clear MDI, MDI(-X) override is only allowed when autoneg enabled */ + hw->mdix = AUTO_ALL_MODES; + return 0; err_inval: From 4e8186b68fb944ad9e7fd4080cd8bd8f10eb7cbd Mon Sep 17 00:00:00 2001 From: Jesse Brandeburg Date: Thu, 26 Jul 2012 02:31:14 +0000 Subject: [PATCH 5/6] e1000e: implement MDI/MDI-X control Some users report issues with link failing when connected to certain switches. This gives the user the ability to control the MDI state from the driver, allowing users to work around some improperly behaving switches. Forcing in this driver is for now only allowed when auto-neg is enabled. This is in regards to the related ethtool app patch and bugzilla.kernel.org bug 11998 Signed-off-by: Jesse Brandeburg CC: bruce.w.allan@intel.com CC: n.poppelier@xs4all.nl CC: bastien@durel.org CC: jsveiga@it.eng.br Tested-by: Aaron Brown aaron.f.brown@intel.com Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/e1000e/ethtool.c | 41 ++++++++++++++++++++- 1 file changed, 39 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c index 0349e2478df8..2e76f06720fd 100644 --- a/drivers/net/ethernet/intel/e1000e/ethtool.c +++ b/drivers/net/ethernet/intel/e1000e/ethtool.c @@ -199,6 +199,11 @@ static int e1000_get_settings(struct net_device *netdev, else ecmd->eth_tp_mdix = ETH_TP_MDI_INVALID; + if (hw->phy.mdix == AUTO_ALL_MODES) + ecmd->eth_tp_mdix_ctrl = ETH_TP_MDI_AUTO; + else + ecmd->eth_tp_mdix_ctrl = hw->phy.mdix; + return 0; } @@ -241,6 +246,10 @@ static int e1000_set_spd_dplx(struct e1000_adapter *adapter, u32 spd, u8 dplx) default: goto err_inval; } + + /* clear MDI, MDI(-X) override is only allowed when autoneg enabled */ + adapter->hw.phy.mdix = AUTO_ALL_MODES; + return 0; err_inval: @@ -264,6 +273,22 @@ static int e1000_set_settings(struct net_device *netdev, return -EINVAL; } + /* + * MDI setting is only allowed when autoneg enabled because + * some hardware doesn't allow MDI setting when speed or + * duplex is forced. + */ + if (ecmd->eth_tp_mdix_ctrl) { + if (hw->phy.media_type != e1000_media_type_copper) + return -EOPNOTSUPP; + + if ((ecmd->eth_tp_mdix_ctrl != ETH_TP_MDI_AUTO) && + (ecmd->autoneg != AUTONEG_ENABLE)) { + e_err("forcing MDI/MDI-X state is not supported when link speed and/or duplex are forced\n"); + return -EINVAL; + } + } + while (test_and_set_bit(__E1000_RESETTING, &adapter->state)) usleep_range(1000, 2000); @@ -282,20 +307,32 @@ static int e1000_set_settings(struct net_device *netdev, hw->fc.requested_mode = e1000_fc_default; } else { u32 speed = ethtool_cmd_speed(ecmd); + /* calling this overrides forced MDI setting */ if (e1000_set_spd_dplx(adapter, speed, ecmd->duplex)) { clear_bit(__E1000_RESETTING, &adapter->state); return -EINVAL; } } + /* MDI-X => 2; MDI => 1; Auto => 3 */ + if (ecmd->eth_tp_mdix_ctrl) { + /* + * fix up the value for auto (3 => 0) as zero is mapped + * internally to auto + */ + if (ecmd->eth_tp_mdix_ctrl == ETH_TP_MDI_AUTO) + hw->phy.mdix = AUTO_ALL_MODES; + else + hw->phy.mdix = ecmd->eth_tp_mdix_ctrl; + } + /* reset the link */ if (netif_running(adapter->netdev)) { e1000e_down(adapter); e1000e_up(adapter); - } else { + } else e1000e_reset(adapter); - } clear_bit(__E1000_RESETTING, &adapter->state); return 0; From 8376dad0c877bc691b2feadd3390a162aa3c3bd9 Mon Sep 17 00:00:00 2001 From: Jesse Brandeburg Date: Thu, 26 Jul 2012 02:31:19 +0000 Subject: [PATCH 6/6] igb: update to allow reading/setting MDI state This is the implementation for igb to allow forcing MDI state via ethtool, allowing users to work around some improperly behaving switches. Forcing in this driver is for now only allowed when auto-neg is enabled. Signed-off-by: Jesse Brandeburg CC: Carolyn Wyborny Tested-by: Aaron Brown aaron.f.brown@intel.com Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/igb/igb_ethtool.c | 42 ++++++++++++++++++++ drivers/net/ethernet/intel/igb/igb_main.c | 4 ++ 2 files changed, 46 insertions(+) diff --git a/drivers/net/ethernet/intel/igb/igb_ethtool.c b/drivers/net/ethernet/intel/igb/igb_ethtool.c index a19c84cad0e9..cf0e9fb45cbd 100644 --- a/drivers/net/ethernet/intel/igb/igb_ethtool.c +++ b/drivers/net/ethernet/intel/igb/igb_ethtool.c @@ -198,6 +198,19 @@ static int igb_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd) } ecmd->autoneg = hw->mac.autoneg ? AUTONEG_ENABLE : AUTONEG_DISABLE; + + /* MDI-X => 2; MDI =>1; Invalid =>0 */ + if (hw->phy.media_type == e1000_media_type_copper) + ecmd->eth_tp_mdix = hw->phy.is_mdix ? ETH_TP_MDI_X : + ETH_TP_MDI; + else + ecmd->eth_tp_mdix = ETH_TP_MDI_INVALID; + + if (hw->phy.mdix == AUTO_ALL_MODES) + ecmd->eth_tp_mdix_ctrl = ETH_TP_MDI_AUTO; + else + ecmd->eth_tp_mdix_ctrl = hw->phy.mdix; + return 0; } @@ -214,6 +227,22 @@ static int igb_set_settings(struct net_device *netdev, struct ethtool_cmd *ecmd) return -EINVAL; } + /* + * MDI setting is only allowed when autoneg enabled because + * some hardware doesn't allow MDI setting when speed or + * duplex is forced. + */ + if (ecmd->eth_tp_mdix_ctrl) { + if (hw->phy.media_type != e1000_media_type_copper) + return -EOPNOTSUPP; + + if ((ecmd->eth_tp_mdix_ctrl != ETH_TP_MDI_AUTO) && + (ecmd->autoneg != AUTONEG_ENABLE)) { + dev_err(&adapter->pdev->dev, "forcing MDI/MDI-X state is not supported when link speed and/or duplex are forced\n"); + return -EINVAL; + } + } + while (test_and_set_bit(__IGB_RESETTING, &adapter->state)) msleep(1); @@ -227,12 +256,25 @@ static int igb_set_settings(struct net_device *netdev, struct ethtool_cmd *ecmd) hw->fc.requested_mode = e1000_fc_default; } else { u32 speed = ethtool_cmd_speed(ecmd); + /* calling this overrides forced MDI setting */ if (igb_set_spd_dplx(adapter, speed, ecmd->duplex)) { clear_bit(__IGB_RESETTING, &adapter->state); return -EINVAL; } } + /* MDI-X => 2; MDI => 1; Auto => 3 */ + if (ecmd->eth_tp_mdix_ctrl) { + /* + * fix up the value for auto (3 => 0) as zero is mapped + * internally to auto + */ + if (ecmd->eth_tp_mdix_ctrl == ETH_TP_MDI_AUTO) + hw->phy.mdix = AUTO_ALL_MODES; + else + hw->phy.mdix = ecmd->eth_tp_mdix_ctrl; + } + /* reset the link */ if (netif_running(adapter->netdev)) { igb_down(adapter); diff --git a/drivers/net/ethernet/intel/igb/igb_main.c b/drivers/net/ethernet/intel/igb/igb_main.c index b7c2d5050572..d4f47a0f6689 100644 --- a/drivers/net/ethernet/intel/igb/igb_main.c +++ b/drivers/net/ethernet/intel/igb/igb_main.c @@ -6676,6 +6676,10 @@ int igb_set_spd_dplx(struct igb_adapter *adapter, u32 spd, u8 dplx) default: goto err_inval; } + + /* clear MDI, MDI(-X) override is only allowed when autoneg enabled */ + adapter->hw.phy.mdix = AUTO_ALL_MODES; + return 0; err_inval: