Merge branch 'fixes' into next/fixes-non-critical

Merge a set of fixes that we missed sending in before v4.0 release. These
will also be sent to -stable.

* fixes: (659 commits)
  ARM: at91/dt: sama5d3 xplained: add phy address for macb1
  kbuild: Create directory for target DTB
  ARM: mvebu: Disable CPU Idle on Armada 38x
  arm64: juno: Fix misleading name of UART reference clock
  ARM: dts: sunxi: Remove overclocked/overvoltaged OPP
  ARM: dts: sun4i: a10-lime: Override and remove 1008MHz OPP setting
  ARM: socfpga: dts: fix spi1 interrupt
  ARM: dts: Fix gpio interrupts for dm816x
  ARM: dts: dra7: remove ti,hwmod property from pcie phy
  ARM: EXYNOS: Fix build breakage cpuidle on !SMP
  ARM: OMAP: dmtimer: disable pm runtime on remove
  ARM: OMAP: dmtimer: check for pm_runtime_get_sync() failure
  ARM: dts: fix lid and power pin-functions for exynos5250-spring
  ARM: dts: fix mmc node updates for exynos5250-spring
  ARM: OMAP2+: Fix socbus family info for AM33xx devices
  ARM: dts: omap3: Add missing dmas for crypto
  + Linux 4.0-rc4

Signed-off-by: Olof Johansson <olof@lixom.net>

Documentation/devicetree/bindings/arm/exynos/power_domain.txt

@@ -22,6 +22,8 @@ Optional Properties:
 	- pclkN, clkN: Pairs of parent of input clock and input clock to the
 		devices in this power domain. Maximum of 4 pairs (N = 0 to 3)
 		are supported currently.
+- power-domains: phandle pointing to the parent power domain, for more details
+		 see Documentation/devicetree/bindings/power/power_domain.txt
 
 Node of a device using power domains must have a power-domains property
 defined with a phandle to respective power domain.

Documentation/devicetree/bindings/arm/sti.txt

@@ -13,6 +13,10 @@ Boards with the ST STiH407 SoC shall have the following properties:
 Required root node property:
 compatible = "st,stih407";
 
+Boards with the ST STiH410 SoC shall have the following properties:
+Required root node property:
+compatible = "st,stih410";
+
 Boards with the ST STiH418 SoC shall have the following properties:
 Required root node property:
 compatible = "st,stih418";

Documentation/devicetree/bindings/i2c/i2c-imx.txt

@@ -7,6 +7,7 @@ Required properties:
   - "fsl,vf610-i2c" for I2C compatible with the one integrated on Vybrid vf610 SoC
 - reg : Should contain I2C/HS-I2C registers location and length
 - interrupts : Should contain I2C/HS-I2C interrupt
+- clocks : Should contain the I2C/HS-I2C clock specifier
 
 Optional properties:
 - clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz.

Documentation/devicetree/bindings/net/amd-xgbe-phy.txt

@@ -27,6 +27,8 @@ property is used.
 - amd,serdes-cdr-rate: CDR rate speed selection
 - amd,serdes-pq-skew: PQ (data sampling) skew
 - amd,serdes-tx-amp: TX amplitude boost
+- amd,serdes-dfe-tap-config: DFE taps available to run
+- amd,serdes-dfe-tap-enable: DFE taps to enable
 
 Example:
 	xgbe_phy@e1240800 {
@@ -41,4 +43,6 @@ Example:
 		amd,serdes-cdr-rate = <2>, <2>, <7>;
 		amd,serdes-pq-skew = <10>, <10>, <30>;
 		amd,serdes-tx-amp = <15>, <15>, <10>;
+		amd,serdes-dfe-tap-config = <3>, <3>, <1>;
+		amd,serdes-dfe-tap-enable = <0>, <0>, <127>;
 	};

Documentation/devicetree/bindings/net/apm-xgene-enet.txt

@@ -4,7 +4,10 @@ Ethernet nodes are defined to describe on-chip ethernet interfaces in
 APM X-Gene SoC.
 
 Required properties for all the ethernet interfaces:
-- compatible: Should be "apm,xgene-enet"
+- compatible: Should state binding information from the following list,
+  - "apm,xgene-enet":    RGMII based 1G interface
+  - "apm,xgene1-sgenet": SGMII based 1G interface
+  - "apm,xgene1-xgenet": XFI based 10G interface
 - reg: Address and length of the register set for the device. It contains the
   information of registers in the same order as described by reg-names
 - reg-names: Should contain the register set names

Documentation/devicetree/bindings/power/power_domain.txt

@@ -19,6 +19,16 @@ Required properties:
    providing multiple PM domains (e.g. power controllers), but can be any value
    as specified by device tree binding documentation of particular provider.
 
+Optional properties:
+ - power-domains : A phandle and PM domain specifier as defined by bindings of
+                   the power controller specified by phandle.
+   Some power domains might be powered from another power domain (or have
+   other hardware specific dependencies). For representing such dependency
+   a standard PM domain consumer binding is used. When provided, all domains
+   created by the given provider should be subdomains of the domain
+   specified by this binding. More details about power domain specifier are
+   available in the next section.
+
 Example:
 
 	power: power-controller@12340000 {
@@ -30,6 +40,25 @@ Example:
 The node above defines a power controller that is a PM domain provider and
 expects one cell as its phandle argument.
 
+Example 2:
+
+	parent: power-controller@12340000 {
+		compatible = "foo,power-controller";
+		reg = <0x12340000 0x1000>;
+		#power-domain-cells = <1>;
+	};
+
+	child: power-controller@12340000 {
+		compatible = "foo,power-controller";
+		reg = <0x12341000 0x1000>;
+		power-domains = <&parent 0>;
+		#power-domain-cells = <1>;
+	};
+
+The nodes above define two power controllers: 'parent' and 'child'.
+Domains created by the 'child' power controller are subdomains of '0' power
+domain provided by the 'parent' power controller.
+
 ==PM domain consumers==
 
 Required properties:

Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt

@@ -0,0 +1,19 @@
+ETRAX FS UART
+
+Required properties:
+- compatible : "axis,etraxfs-uart"
+- reg: offset and length of the register set for the device.
+- interrupts: device interrupt
+
+Optional properties:
+- {dtr,dsr,ri,cd}-gpios: specify a GPIO for DTR/DSR/RI/CD
+  line respectively.
+
+Example:
+
+serial@b00260000 {
+	compatible = "axis,etraxfs-uart";
+	reg = <0xb0026000 0x1000>;
+	interrupts = <68>;
+	status = "disabled";
+};

Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt

@@ -21,6 +21,18 @@ Optional properties:
 - reg-io-width : the size (in bytes) of the IO accesses that should be
   performed on the device.  If this property is not present then single byte
   accesses are used.
+- dcd-override : Override the DCD modem status signal. This signal will always
+  be reported as active instead of being obtained from the modem status
+  register. Define this if your serial port does not use this pin.
+- dsr-override : Override the DTS modem status signal. This signal will always
+  be reported as active instead of being obtained from the modem status
+  register. Define this if your serial port does not use this pin.
+- cts-override : Override the CTS modem status signal. This signal will always
+  be reported as active instead of being obtained from the modem status
+  register. Define this if your serial port does not use this pin.
+- ri-override : Override the RI modem status signal. This signal will always be
+  reported as inactive instead of being obtained from the modem status register.
+  Define this if your serial port does not use this pin.
 
 Example:
 
@@ -31,6 +43,10 @@ Example:
 		interrupts = <10>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		dcd-override;
+		dsr-override;
+		cts-override;
+		ri-override;
 	};
 
 Example with one clock:

Documentation/devicetree/bindings/submitting-patches.txt

@@ -12,6 +12,9 @@ I. For patch submitters
 
        devicetree@vger.kernel.org
 
+     and Cc: the DT maintainers. Use scripts/get_maintainer.pl to identify
+     all of the DT maintainers.
+
   3) The Documentation/ portion of the patch should come in the series before
      the code implementing the binding.
 

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -20,6 +20,7 @@ amlogic	Amlogic, Inc.
 ams	AMS AG
 amstaos	AMS-Taos Inc.
 apm	Applied Micro Circuits Corporation (APM)
+arasan	Arasan Chip Systems
 arm	ARM Ltd.
 armadeus	ARMadeus Systems SARL
 asahi-kasei	Asahi Kasei Corp.
@@ -27,6 +28,7 @@ atmel	Atmel Corporation
 auo	AU Optronics Corporation
 avago	Avago Technologies
 avic	Shanghai AVIC Optoelectronics Co., Ltd.
+axis	Axis Communications AB
 bosch	Bosch Sensortec GmbH
 brcm	Broadcom Corporation
 buffalo	Buffalo, Inc.

Documentation/devicetree/bindings/watchdog/atmel-wdt.txt

@@ -26,6 +26,11 @@ Optional properties:
 - atmel,disable : Should be present if you want to disable the watchdog.
 - atmel,idle-halt : Should be present if you want to stop the watchdog when
 	entering idle state.
+	CAUTION: This property should be used with care, it actually makes the
+	watchdog not counting when the CPU is in idle state, therefore the
+	watchdog reset time depends on mean CPU usage and will not reset at all
+	if the CPU stop working while it is in idle state, which is probably
+	not what you want.
 - atmel,dbg-halt : Should be present if you want to stop the watchdog when
 	entering debug state.