docs: hwmon: w83791d: convert to ReST format
Convert w83791d to ReST format, in order to allow it to be parsed by Sphinx. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This commit is contained in:
Mauro Carvalho Chehab
Guenter Roeck
parent
b413e3fa7f
commit
ce09cfb600
@ -2,9 +2,13 @@ Kernel driver w83791d
|
||||
=====================
|
||||
|
||||
Supported chips:
|
||||
|
||||
* Winbond W83791D
|
||||
|
||||
Prefix: 'w83791d'
|
||||
|
||||
Addresses scanned: I2C 0x2c - 0x2f
|
||||
|
||||
Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83791D_W83791Gb.pdf
|
||||
|
||||
Author: Charles Spirakis <bezaur@gmail.com>
|
||||
@ -12,23 +16,29 @@ Author: Charles Spirakis <bezaur@gmail.com>
|
||||
This driver was derived from the w83781d.c and w83792d.c source files.
|
||||
|
||||
Credits:
|
||||
|
||||
w83781d.c:
|
||||
Frodo Looijaard <frodol@dds.nl>,
|
||||
Philip Edelbrock <phil@netroedge.com>,
|
||||
and Mark Studebaker <mdsxyz123@yahoo.com>
|
||||
|
||||
- Frodo Looijaard <frodol@dds.nl>,
|
||||
- Philip Edelbrock <phil@netroedge.com>,
|
||||
- Mark Studebaker <mdsxyz123@yahoo.com>
|
||||
|
||||
w83792d.c:
|
||||
Shane Huang (Winbond),
|
||||
Rudolf Marek <r.marek@assembler.cz>
|
||||
|
||||
- Shane Huang (Winbond),
|
||||
- Rudolf Marek <r.marek@assembler.cz>
|
||||
|
||||
Additional contributors:
|
||||
Sven Anders <anders@anduras.de>
|
||||
Marc Hulsman <m.hulsman@tudelft.nl>
|
||||
|
||||
- Sven Anders <anders@anduras.de>
|
||||
- Marc Hulsman <m.hulsman@tudelft.nl>
|
||||
|
||||
Module Parameters
|
||||
-----------------
|
||||
|
||||
* init boolean
|
||||
(default 0)
|
||||
|
||||
Use 'init=1' to have the driver do extra software initializations.
|
||||
The default behavior is to do the minimum initialization possible
|
||||
and depend on the BIOS to properly setup the chip. If you know you
|
||||
@ -37,12 +47,13 @@ Module Parameters
|
||||
|
||||
* reset boolean
|
||||
(default 0)
|
||||
|
||||
Use 'reset=1' to reset the chip (via index 0x40, bit 7). The default
|
||||
behavior is no chip reset to preserve BIOS settings.
|
||||
|
||||
* force_subclients=bus,caddr,saddr,saddr
|
||||
This is used to force the i2c addresses for subclients of
|
||||
a certain chip. Example usage is `force_subclients=0,0x2f,0x4a,0x4b'
|
||||
a certain chip. Example usage is `force_subclients=0,0x2f,0x4a,0x4b`
|
||||
to force the subclients of chip 0x2f on bus 0 to i2c addresses
|
||||
0x4a and 0x4b.
|
||||
|
||||
@ -91,11 +102,11 @@ This file is used for both legacy and new code.
|
||||
|
||||
The sysfs interface to the beep bitmask has migrated from the original legacy
|
||||
method of a single sysfs beep_mask file to a newer method using multiple
|
||||
*_beep files as described in .../Documentation/hwmon/sysfs-interface.
|
||||
`*_beep` files as described in `Documentation/hwmon/sysfs-interface`.
|
||||
|
||||
A similar change has occurred for the bitmap corresponding to the alarms. The
|
||||
original legacy method used a single sysfs alarms file containing a bitmap
|
||||
of triggered alarms. The newer method uses multiple sysfs *_alarm files
|
||||
of triggered alarms. The newer method uses multiple sysfs `*_alarm` files
|
||||
(again following the pattern described in sysfs-interface).
|
||||
|
||||
Since both methods read and write the underlying hardware, they can be used
|
||||
@ -116,46 +127,54 @@ User mode code requesting values more often will receive cached values.
|
||||
The sysfs-interface is documented in the 'sysfs-interface' file. Only
|
||||
chip-specific options are documented here.
|
||||
|
||||
pwm[1-3]_enable - this file controls mode of fan/temperature control for
|
||||
======================= =======================================================
|
||||
pwm[1-3]_enable this file controls mode of fan/temperature control for
|
||||
fan 1-3. Fan/PWM 4-5 only support manual mode.
|
||||
|
||||
* 1 Manual mode
|
||||
* 2 Thermal Cruise mode
|
||||
* 3 Fan Speed Cruise mode (no further support)
|
||||
|
||||
temp[1-3]_target - defines the target temperature for Thermal Cruise mode.
|
||||
temp[1-3]_target defines the target temperature for Thermal Cruise mode.
|
||||
Unit: millidegree Celsius
|
||||
RW
|
||||
|
||||
temp[1-3]_tolerance - temperature tolerance for Thermal Cruise mode.
|
||||
temp[1-3]_tolerance temperature tolerance for Thermal Cruise mode.
|
||||
Specifies an interval around the target temperature
|
||||
in which the fan speed is not changed.
|
||||
Unit: millidegree Celsius
|
||||
RW
|
||||
======================= =======================================================
|
||||
|
||||
Alarms bitmap vs. beep_mask bitmask
|
||||
------------------------------------
|
||||
-----------------------------------
|
||||
|
||||
For legacy code using the alarms and beep_mask files:
|
||||
|
||||
in0 (VCORE) : alarms: 0x000001 beep_mask: 0x000001
|
||||
in1 (VINR0) : alarms: 0x000002 beep_mask: 0x002000 <== mismatch
|
||||
in2 (+3.3VIN): alarms: 0x000004 beep_mask: 0x000004
|
||||
in3 (5VDD) : alarms: 0x000008 beep_mask: 0x000008
|
||||
in4 (+12VIN) : alarms: 0x000100 beep_mask: 0x000100
|
||||
in5 (-12VIN) : alarms: 0x000200 beep_mask: 0x000200
|
||||
in6 (-5VIN) : alarms: 0x000400 beep_mask: 0x000400
|
||||
in7 (VSB) : alarms: 0x080000 beep_mask: 0x010000 <== mismatch
|
||||
in8 (VBAT) : alarms: 0x100000 beep_mask: 0x020000 <== mismatch
|
||||
in9 (VINR1) : alarms: 0x004000 beep_mask: 0x004000
|
||||
temp1 : alarms: 0x000010 beep_mask: 0x000010
|
||||
temp2 : alarms: 0x000020 beep_mask: 0x000020
|
||||
temp3 : alarms: 0x002000 beep_mask: 0x000002 <== mismatch
|
||||
fan1 : alarms: 0x000040 beep_mask: 0x000040
|
||||
fan2 : alarms: 0x000080 beep_mask: 0x000080
|
||||
fan3 : alarms: 0x000800 beep_mask: 0x000800
|
||||
fan4 : alarms: 0x200000 beep_mask: 0x200000
|
||||
fan5 : alarms: 0x400000 beep_mask: 0x400000
|
||||
tart1 : alarms: 0x010000 beep_mask: 0x040000 <== mismatch
|
||||
tart2 : alarms: 0x020000 beep_mask: 0x080000 <== mismatch
|
||||
tart3 : alarms: 0x040000 beep_mask: 0x100000 <== mismatch
|
||||
case_open : alarms: 0x001000 beep_mask: 0x001000
|
||||
global_enable: alarms: -------- beep_mask: 0x800000 (modified via beep_enable)
|
||||
============= ======== ========= ==========================
|
||||
Signal Alarms beep_mask Obs
|
||||
============= ======== ========= ==========================
|
||||
in0 (VCORE) 0x000001 0x000001
|
||||
in1 (VINR0) 0x000002 0x002000 <== mismatch
|
||||
in2 (+3.3VIN) 0x000004 0x000004
|
||||
in3 (5VDD) 0x000008 0x000008
|
||||
in4 (+12VIN) 0x000100 0x000100
|
||||
in5 (-12VIN) 0x000200 0x000200
|
||||
in6 (-5VIN) 0x000400 0x000400
|
||||
in7 (VSB) 0x080000 0x010000 <== mismatch
|
||||
in8 (VBAT) 0x100000 0x020000 <== mismatch
|
||||
in9 (VINR1) 0x004000 0x004000
|
||||
temp1 0x000010 0x000010
|
||||
temp2 0x000020 0x000020
|
||||
temp3 0x002000 0x000002 <== mismatch
|
||||
fan1 0x000040 0x000040
|
||||
fan2 0x000080 0x000080
|
||||
fan3 0x000800 0x000800
|
||||
fan4 0x200000 0x200000
|
||||
fan5 0x400000 0x400000
|
||||
tart1 0x010000 0x040000 <== mismatch
|
||||
tart2 0x020000 0x080000 <== mismatch
|
||||
tart3 0x040000 0x100000 <== mismatch
|
||||
case_open 0x001000 0x001000
|
||||
global_enable - 0x800000 (modified via beep_enable)
|
||||
============= ======== ========= ==========================
|
||||
|
||||
Loading…
Reference in New Issue
Block a user