arm64: dts: qcom: msm8998-fxtec: Decouple from 8998 MTP
While the Pro-1 is based on MTP and is very close to it, it's really not great for it to include the MTP dtsi straight up, as any small change will affect both boards and not all of them will apply to the phone as well. Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220430162353.607709-13-konrad.dybcio@somainline.org
This commit is contained in:
Konrad Dybcio
Bjorn Andersson
parent
5d393f14d4
commit
d0eaf4122c
@ -9,7 +9,10 @@
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
|
||||
#include "msm8998-mtp.dtsi"
|
||||
#include "msm8998.dtsi"
|
||||
#include "pm8005.dtsi"
|
||||
#include "pm8998.dtsi"
|
||||
#include "pmi8998.dtsi"
|
||||
|
||||
/ {
|
||||
model = "F(x)tec Pro1 (QX1000)";
|
||||
@ -17,6 +20,11 @@
|
||||
chassis-type = "handset";
|
||||
qcom,board-id = <0x02000b 0x10>;
|
||||
|
||||
aliases {
|
||||
serial0 = &blsp2_uart1;
|
||||
serial1 = &blsp1_uart3;
|
||||
};
|
||||
|
||||
/*
|
||||
* Until we hook up type-c detection, we
|
||||
* have to stick with this. But it works.
|
||||
@ -186,6 +194,53 @@
|
||||
pinctrl-0 = <&ts_vio_default>;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
vph_pwr: vph-pwr-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vph_pwr";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart3 {
|
||||
status = "okay";
|
||||
|
||||
bluetooth {
|
||||
compatible = "qcom,wcn3990-bt";
|
||||
|
||||
vddio-supply = <&vreg_s4a_1p8>;
|
||||
vddxo-supply = <&vreg_l7a_1p8>;
|
||||
vddrf-supply = <&vreg_l17a_1p3>;
|
||||
vddch0-supply = <&vreg_l25a_3p3>;
|
||||
max-speed = <3200000>;
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart3_on {
|
||||
rx {
|
||||
/delete-property/ bias-disable;
|
||||
/*
|
||||
* Configure a pull-up on 45 (RX). This is needed to
|
||||
* avoid garbage data when the TX pin of the Bluetooth
|
||||
* module is in tri-state (module powered off or not
|
||||
* driving the signal yet).
|
||||
*/
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
cts {
|
||||
/delete-property/ bias-disable;
|
||||
/*
|
||||
* Configure a pull-down on 47 (CTS) to match the pull
|
||||
* of the Bluetooth module.
|
||||
*/
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
|
||||
&blsp2_uart1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp2_i2c1 {
|
||||
@ -204,6 +259,91 @@
|
||||
};
|
||||
};
|
||||
|
||||
&etf {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&etm1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&etm2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&etm3 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&etm4 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&etm5 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&etm6 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&etm7 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&etm8 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&etr {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&funnel1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&funnel2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&funnel3 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&funnel4 {
|
||||
// FIXME: Figure out why clock late_initcall crashes the board with
|
||||
// this enabled.
|
||||
// status = "okay";
|
||||
};
|
||||
|
||||
&funnel5 {
|
||||
// FIXME: Figure out why clock late_initcall crashes the board with
|
||||
// this enabled.
|
||||
// status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pm8005_regulators {
|
||||
vdd_s1-supply = <&vph_pwr>;
|
||||
|
||||
pm8005_s1: s1 { /* VDD_GFX supply */
|
||||
regulator-min-microvolt = <524000>;
|
||||
regulator-max-microvolt = <1100000>;
|
||||
regulator-enable-ramp-delay = <500>;
|
||||
|
||||
/* Hack until we rig up the gpu consumer */
|
||||
regulator-always-on;
|
||||
};
|
||||
};
|
||||
|
||||
&pm8998_gpio {
|
||||
vol_up_pin_a: vol-up-active {
|
||||
pins = "gpio6";
|
||||
@ -240,6 +380,240 @@
|
||||
};
|
||||
};
|
||||
|
||||
&qusb2phy {
|
||||
status = "okay";
|
||||
|
||||
vdda-pll-supply = <&vreg_l12a_1p8>;
|
||||
vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
|
||||
};
|
||||
|
||||
&replicator1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&rpm_requests {
|
||||
pm8998-regulators {
|
||||
compatible = "qcom,rpm-pm8998-regulators";
|
||||
|
||||
vdd_s1-supply = <&vph_pwr>;
|
||||
vdd_s2-supply = <&vph_pwr>;
|
||||
vdd_s3-supply = <&vph_pwr>;
|
||||
vdd_s4-supply = <&vph_pwr>;
|
||||
vdd_s5-supply = <&vph_pwr>;
|
||||
vdd_s6-supply = <&vph_pwr>;
|
||||
vdd_s7-supply = <&vph_pwr>;
|
||||
vdd_s8-supply = <&vph_pwr>;
|
||||
vdd_s9-supply = <&vph_pwr>;
|
||||
vdd_s10-supply = <&vph_pwr>;
|
||||
vdd_s11-supply = <&vph_pwr>;
|
||||
vdd_s12-supply = <&vph_pwr>;
|
||||
vdd_s13-supply = <&vph_pwr>;
|
||||
vdd_l1_l27-supply = <&vreg_s7a_1p025>;
|
||||
vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
|
||||
vdd_l3_l11-supply = <&vreg_s7a_1p025>;
|
||||
vdd_l4_l5-supply = <&vreg_s7a_1p025>;
|
||||
vdd_l6-supply = <&vreg_s5a_2p04>;
|
||||
vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
|
||||
vdd_l9-supply = <&vreg_bob>;
|
||||
vdd_l10_l23_l25-supply = <&vreg_bob>;
|
||||
vdd_l13_l19_l21-supply = <&vreg_bob>;
|
||||
vdd_l16_l28-supply = <&vreg_bob>;
|
||||
vdd_l18_l22-supply = <&vreg_bob>;
|
||||
vdd_l20_l24-supply = <&vreg_bob>;
|
||||
vdd_l26-supply = <&vreg_s3a_1p35>;
|
||||
vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
|
||||
|
||||
vreg_s3a_1p35: s3 {
|
||||
regulator-min-microvolt = <1352000>;
|
||||
regulator-max-microvolt = <1352000>;
|
||||
};
|
||||
|
||||
vreg_s4a_1p8: s4 {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-allow-set-load;
|
||||
};
|
||||
|
||||
vreg_s5a_2p04: s5 {
|
||||
regulator-min-microvolt = <1904000>;
|
||||
regulator-max-microvolt = <2040000>;
|
||||
};
|
||||
|
||||
vreg_s7a_1p025: s7 {
|
||||
regulator-min-microvolt = <900000>;
|
||||
regulator-max-microvolt = <1028000>;
|
||||
};
|
||||
|
||||
vreg_l1a_0p875: l1 {
|
||||
regulator-min-microvolt = <880000>;
|
||||
regulator-max-microvolt = <880000>;
|
||||
};
|
||||
|
||||
vreg_l2a_1p2: l2 {
|
||||
regulator-min-microvolt = <1200000>;
|
||||
regulator-max-microvolt = <1200000>;
|
||||
};
|
||||
|
||||
vreg_l3a_1p0: l3 {
|
||||
regulator-min-microvolt = <1000000>;
|
||||
regulator-max-microvolt = <1000000>;
|
||||
};
|
||||
|
||||
vreg_l5a_0p8: l5 {
|
||||
regulator-min-microvolt = <800000>;
|
||||
regulator-max-microvolt = <800000>;
|
||||
};
|
||||
|
||||
vreg_l6a_1p8: l6 {
|
||||
regulator-min-microvolt = <1808000>;
|
||||
regulator-max-microvolt = <1808000>;
|
||||
};
|
||||
|
||||
vreg_l7a_1p8: l7 {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
};
|
||||
|
||||
vreg_l8a_1p2: l8 {
|
||||
regulator-min-microvolt = <1200000>;
|
||||
regulator-max-microvolt = <1200000>;
|
||||
};
|
||||
|
||||
vreg_l9a_1p8: l9 {
|
||||
regulator-min-microvolt = <1808000>;
|
||||
regulator-max-microvolt = <2960000>;
|
||||
};
|
||||
|
||||
vreg_l10a_1p8: l10 {
|
||||
regulator-min-microvolt = <1808000>;
|
||||
regulator-max-microvolt = <2960000>;
|
||||
};
|
||||
|
||||
vreg_l11a_1p0: l11 {
|
||||
regulator-min-microvolt = <1000000>;
|
||||
regulator-max-microvolt = <1000000>;
|
||||
};
|
||||
|
||||
vreg_l12a_1p8: l12 {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
};
|
||||
|
||||
vreg_l13a_2p95: l13 {
|
||||
regulator-min-microvolt = <1808000>;
|
||||
regulator-max-microvolt = <2960000>;
|
||||
};
|
||||
|
||||
vreg_l14a_1p88: l14 {
|
||||
regulator-min-microvolt = <1880000>;
|
||||
regulator-max-microvolt = <1880000>;
|
||||
};
|
||||
|
||||
vreg_l15a_1p8: l15 {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
};
|
||||
|
||||
vreg_l16a_2p7: l16 {
|
||||
regulator-min-microvolt = <2704000>;
|
||||
regulator-max-microvolt = <2704000>;
|
||||
};
|
||||
|
||||
vreg_l17a_1p3: l17 {
|
||||
regulator-min-microvolt = <1304000>;
|
||||
regulator-max-microvolt = <1304000>;
|
||||
};
|
||||
|
||||
vreg_l18a_2p7: l18 {
|
||||
regulator-min-microvolt = <2704000>;
|
||||
regulator-max-microvolt = <2704000>;
|
||||
};
|
||||
|
||||
vreg_l19a_3p0: l19 {
|
||||
regulator-min-microvolt = <3008000>;
|
||||
regulator-max-microvolt = <3008000>;
|
||||
};
|
||||
|
||||
vreg_l20a_2p95: l20 {
|
||||
regulator-min-microvolt = <2960000>;
|
||||
regulator-max-microvolt = <2960000>;
|
||||
regulator-allow-set-load;
|
||||
};
|
||||
|
||||
vreg_l21a_2p95: l21 {
|
||||
regulator-min-microvolt = <2960000>;
|
||||
regulator-max-microvolt = <2960000>;
|
||||
regulator-system-load = <800000>;
|
||||
regulator-allow-set-load;
|
||||
};
|
||||
|
||||
vreg_l22a_2p85: l22 {
|
||||
regulator-min-microvolt = <2864000>;
|
||||
regulator-max-microvolt = <2864000>;
|
||||
};
|
||||
|
||||
vreg_l23a_3p3: l23 {
|
||||
regulator-min-microvolt = <3312000>;
|
||||
regulator-max-microvolt = <3312000>;
|
||||
};
|
||||
|
||||
vreg_l24a_3p075: l24 {
|
||||
regulator-min-microvolt = <3088000>;
|
||||
regulator-max-microvolt = <3088000>;
|
||||
};
|
||||
|
||||
vreg_l25a_3p3: l25 {
|
||||
regulator-min-microvolt = <3104000>;
|
||||
regulator-max-microvolt = <3312000>;
|
||||
};
|
||||
|
||||
vreg_l26a_1p2: l26 {
|
||||
regulator-min-microvolt = <1200000>;
|
||||
regulator-max-microvolt = <1200000>;
|
||||
regulator-allow-set-load;
|
||||
};
|
||||
|
||||
vreg_l28_3p0: l28 {
|
||||
regulator-min-microvolt = <3008000>;
|
||||
regulator-max-microvolt = <3008000>;
|
||||
};
|
||||
|
||||
vreg_lvs1a_1p8: lvs1 {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
};
|
||||
|
||||
vreg_lvs2a_1p8: lvs2 {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
pmi8998-regulators {
|
||||
compatible = "qcom,rpm-pmi8998-regulators";
|
||||
|
||||
vdd_bob-supply = <&vph_pwr>;
|
||||
|
||||
vreg_bob: bob {
|
||||
regulator-min-microvolt = <3312000>;
|
||||
regulator-max-microvolt = <3600000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&remoteproc_adsp {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&remoteproc_mss {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&remoteproc_slpi {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
gpio-reserved-ranges = <0 4>;
|
||||
|
||||
@ -288,12 +662,41 @@
|
||||
};
|
||||
};
|
||||
|
||||
&ufshc {
|
||||
&sdhc2 {
|
||||
status = "okay";
|
||||
cd-gpios = <&tlmm 95 GPIO_ACTIVE_LOW>;
|
||||
|
||||
vmmc-supply = <&vreg_l21a_2p95>;
|
||||
vqmmc-supply = <&vreg_l13a_2p95>;
|
||||
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&sdc2_on &sdc2_cd>;
|
||||
pinctrl-1 = <&sdc2_off &sdc2_cd>;
|
||||
};
|
||||
|
||||
&stm {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ufshc {
|
||||
status = "okay";
|
||||
vcc-supply = <&vreg_l20a_2p95>;
|
||||
vccq-supply = <&vreg_l26a_1p2>;
|
||||
vccq2-supply = <&vreg_s4a_1p8>;
|
||||
vcc-max-microamp = <750000>;
|
||||
vccq-max-microamp = <560000>;
|
||||
vccq2-max-microamp = <750000>;
|
||||
};
|
||||
|
||||
&ufsphy {
|
||||
status = "okay";
|
||||
vdda-phy-supply = <&vreg_l1a_0p875>;
|
||||
vdda-pll-supply = <&vreg_l2a_1p2>;
|
||||
vddp-ref-clk-supply = <&vreg_l26a_1p2>;
|
||||
};
|
||||
|
||||
&usb3 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_dwc3 {
|
||||
@ -301,8 +704,24 @@
|
||||
extcon = <&extcon_usb>;
|
||||
};
|
||||
|
||||
&usb3phy {
|
||||
status = "okay";
|
||||
|
||||
vdda-phy-supply = <&vreg_l1a_0p875>;
|
||||
vdda-pll-supply = <&vreg_l2a_1p2>;
|
||||
};
|
||||
|
||||
/* GT9286 analog supply */
|
||||
&vreg_l28_3p0 {
|
||||
regulator-min-microvolt = <2800000>;
|
||||
regulator-max-microvolt = <2800000>;
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
|
||||
vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
|
||||
vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
|
||||
vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
|
||||
vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
|
||||
};
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user