arm64: dts: qcom: sm8650-mtp: add interconnect dependent device nodes
Now interconnect dependent devices are added in sm8650 DTSI, now enable more devices for the Qualcomm SM8650 MTP board: - PCIe - Display - DSPs - SDCard - UFS - USB role switch with PMIC Glink Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20231130-topic-sm8650-upstream-dt-v5-7-b25fb781da52@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
This commit is contained in:
Neil Armstrong
Bjorn Andersson
parent
10e0246712
commit
deb63527ab
@ -28,6 +28,44 @@
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
pmic-glink {
|
||||
compatible = "qcom,sm8650-pmic-glink",
|
||||
"qcom,sm8550-pmic-glink",
|
||||
"qcom,pmic-glink";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
orientation-gpios = <&tlmm 29 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
connector@0 {
|
||||
compatible = "usb-c-connector";
|
||||
reg = <0>;
|
||||
|
||||
power-role = "dual";
|
||||
data-role = "dual";
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
|
||||
pmic_glink_hs_in: endpoint {
|
||||
remote-endpoint = <&usb_1_dwc3_hs>;
|
||||
};
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
|
||||
pmic_glink_ss_in: endpoint {
|
||||
remote-endpoint = <&usb_1_dwc3_ss>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
vph_pwr: vph-pwr-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
|
||||
@ -77,6 +115,9 @@
|
||||
regulator-min-microvolt = <3008000>;
|
||||
regulator-max-microvolt = <3008000>;
|
||||
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
||||
regulator-allow-set-load;
|
||||
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
|
||||
RPMH_REGULATOR_MODE_HPM>;
|
||||
};
|
||||
|
||||
vreg_l5b_3p1: ldo5 {
|
||||
@ -389,6 +430,106 @@
|
||||
};
|
||||
};
|
||||
|
||||
&dispcc {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdss {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdss_dsi0 {
|
||||
vdda-supply = <&vreg_l3i_1p2>;
|
||||
|
||||
status = "okay";
|
||||
|
||||
panel@0 {
|
||||
compatible = "visionox,vtdr6130";
|
||||
reg = <0>;
|
||||
|
||||
reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
|
||||
|
||||
vddio-supply = <&vreg_l12b_1p8>;
|
||||
vci-supply = <&vreg_l13b_3p0>;
|
||||
vdd-supply = <&vreg_l11b_1p2>;
|
||||
|
||||
pinctrl-0 = <&disp0_reset_n_active>, <&mdp_vsync_active>;
|
||||
pinctrl-1 = <&disp0_reset_n_suspend>, <&mdp_vsync_suspend>;
|
||||
pinctrl-names = "default", "sleep";
|
||||
|
||||
port {
|
||||
panel0_in: endpoint {
|
||||
remote-endpoint = <&mdss_dsi0_out>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdss_dsi0_out {
|
||||
remote-endpoint = <&panel0_in>;
|
||||
data-lanes = <0 1 2 3>;
|
||||
};
|
||||
|
||||
&mdss_dsi0_phy {
|
||||
vdds-supply = <&vreg_l1i_0p88>;
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdss_mdp {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie_1_phy_aux_clk {
|
||||
clock-frequency = <1000>;
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
|
||||
perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
|
||||
|
||||
pinctrl-0 = <&pcie0_default_state>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0_phy {
|
||||
vdda-phy-supply = <&vreg_l1i_0p88>;
|
||||
vdda-pll-supply = <&vreg_l3i_1p2>;
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
|
||||
perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
|
||||
|
||||
pinctrl-0 = <&pcie1_default_state>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie1_phy {
|
||||
vdda-phy-supply = <&vreg_l3e_0p9>;
|
||||
vdda-pll-supply = <&vreg_l3i_1p2>;
|
||||
vdda-qref-supply = <&vreg_l1i_0p88>;
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pm8550_gpios {
|
||||
sdc2_card_det_n: sdc2-card-det-state {
|
||||
pins = "gpio12";
|
||||
function = "normal";
|
||||
bias-pull-up;
|
||||
input-enable;
|
||||
output-disable;
|
||||
power-source = <1>; /* 1.8 V */
|
||||
};
|
||||
};
|
||||
|
||||
&pm8550b_eusb2_repeater {
|
||||
vdd18-supply = <&vreg_l15b_1p8>;
|
||||
vdd3-supply = <&vreg_l5b_3p1>;
|
||||
@ -398,6 +539,43 @@
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&remoteproc_adsp {
|
||||
firmware-name = "qcom/sm8650/adsp.mbn",
|
||||
"qcom/sm8650/adsp_dtb.mbn";
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&remoteproc_cdsp {
|
||||
firmware-name = "qcom/sm8650/cdsp.mbn",
|
||||
"qcom/sm8650/cdsp_dtb.mbn";
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&remoteproc_mpss {
|
||||
firmware-name = "qcom/sm8650/modem.mbn",
|
||||
"qcom/sm8650/modem_dtb.mbn";
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&sdhc_2 {
|
||||
cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>;
|
||||
|
||||
vmmc-supply = <&vreg_l9b_2p9>;
|
||||
vqmmc-supply = <&vreg_l8b_1p8>;
|
||||
bus-width = <4>;
|
||||
no-sdio;
|
||||
no-mmc;
|
||||
|
||||
pinctrl-0 = <&sdc2_default>, <&sdc2_card_det_n>;
|
||||
pinctrl-1 = <&sdc2_sleep>, <&sdc2_card_det_n>;
|
||||
pinctrl-names = "default", "sleep";
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&sleep_clk {
|
||||
clock-frequency = <32000>;
|
||||
};
|
||||
@ -405,12 +583,58 @@
|
||||
&tlmm {
|
||||
/* Reserved I/Os for NFC */
|
||||
gpio-reserved-ranges = <32 8>;
|
||||
|
||||
disp0_reset_n_active: disp0-reset-n-active-state {
|
||||
pins = "gpio133";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
disp0_reset_n_suspend: disp0-reset-n-suspend-state {
|
||||
pins = "gpio133";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
mdp_vsync_active: mdp-vsync-active-state {
|
||||
pins = "gpio86";
|
||||
function = "mdp_vsync";
|
||||
drive-strength = <2>;
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
mdp_vsync_suspend: mdp-vsync-suspend-state {
|
||||
pins = "gpio86";
|
||||
function = "mdp_vsync";
|
||||
drive-strength = <2>;
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
|
||||
&uart15 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ufs_mem_hc {
|
||||
reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
|
||||
|
||||
vcc-supply = <&vreg_l17b_2p5>;
|
||||
vcc-max-microamp = <1300000>;
|
||||
vccq-supply = <&vreg_l1c_1p2>;
|
||||
vccq-max-microamp = <1200000>;
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ufs_mem_phy {
|
||||
vdda-phy-supply = <&vreg_l1d_0p88>;
|
||||
vdda-pll-supply = <&vreg_l3i_1p2>;
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/*
|
||||
* DPAUX -> WCD9395 -> USB_SBU -> USB-C
|
||||
* eUSB2 DP/DM -> PM85550HS -> eUSB2 DP/DM -> USB-C
|
||||
@ -422,7 +646,16 @@
|
||||
};
|
||||
|
||||
&usb_1_dwc3 {
|
||||
dr_mode = "peripheral";
|
||||
dr_mode = "otg";
|
||||
usb-role-switch;
|
||||
};
|
||||
|
||||
&usb_1_dwc3_hs {
|
||||
remote-endpoint = <&pmic_glink_hs_in>;
|
||||
};
|
||||
|
||||
&usb_1_dwc3_ss {
|
||||
remote-endpoint = <&pmic_glink_ss_in>;
|
||||
};
|
||||
|
||||
&usb_1_hsphy {
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user