diff --git a/Documentation/networking/sfp-phylink.rst b/Documentation/networking/sfp-phylink.rst
index a5e00a159d21..d753a309f9d1 100644
--- a/Documentation/networking/sfp-phylink.rst
+++ b/Documentation/networking/sfp-phylink.rst
@@ -251,7 +251,8 @@ this documentation.
 	phylink_mac_change(priv->phylink, link_is_up);
 
     where ``link_is_up`` is true if the link is currently up or false
-    otherwise.
+    otherwise. If a MAC is unable to provide these interrupts, then
+    it should set ``priv->phylink_config.pcs_poll = true;`` in step 9.
 
 11. Verify that the driver does not call::
 
diff --git a/drivers/net/dsa/ocelot/Kconfig b/drivers/net/dsa/ocelot/Kconfig
index 6f9804093150..a5b7cca03d09 100644
--- a/drivers/net/dsa/ocelot/Kconfig
+++ b/drivers/net/dsa/ocelot/Kconfig
@@ -3,8 +3,10 @@ config NET_DSA_MSCC_FELIX
 	tristate "Ocelot / Felix Ethernet switch support"
 	depends on NET_DSA && PCI
 	depends on NET_VENDOR_MICROSEMI
+	depends on NET_VENDOR_FREESCALE
 	select MSCC_OCELOT_SWITCH
 	select NET_DSA_TAG_OCELOT
+	select FSL_ENETC_MDIO
 	help
 	  This driver supports the VSC9959 network switch, which is a member of
 	  the Vitesse / Microsemi / Microchip Ocelot family of switching cores.
diff --git a/drivers/net/dsa/ocelot/felix.c b/drivers/net/dsa/ocelot/felix.c
index b7f92464815d..f072dd75cea2 100644
--- a/drivers/net/dsa/ocelot/felix.c
+++ b/drivers/net/dsa/ocelot/felix.c
@@ -2,9 +2,14 @@
 /* Copyright 2019 NXP Semiconductors
  */
 #include <uapi/linux/if_bridge.h>
+#include <soc/mscc/ocelot_qsys.h>
+#include <soc/mscc/ocelot_sys.h>
+#include <soc/mscc/ocelot_dev.h>
+#include <soc/mscc/ocelot_ana.h>
 #include <soc/mscc/ocelot.h>
 #include <linux/packing.h>
 #include <linux/module.h>
+#include <linux/of_net.h>
 #include <linux/pci.h>
 #include <linux/of.h>
 #include <net/dsa.h>
@@ -26,14 +31,6 @@ static int felix_set_ageing_time(struct dsa_switch *ds,
 	return 0;
 }
 
-static void felix_adjust_link(struct dsa_switch *ds, int port,
-			      struct phy_device *phydev)
-{
-	struct ocelot *ocelot = ds->priv;
-
-	ocelot_adjust_link(ocelot, port, phydev);
-}
-
 static int felix_fdb_dump(struct dsa_switch *ds, int port,
 			  dsa_fdb_dump_cb_t *cb, void *data)
 {
@@ -155,6 +152,138 @@ static void felix_port_disable(struct dsa_switch *ds, int port)
 	return ocelot_port_disable(ocelot, port);
 }
 
+static void felix_phylink_validate(struct dsa_switch *ds, int port,
+				   unsigned long *supported,
+				   struct phylink_link_state *state)
+{
+	struct ocelot *ocelot = ds->priv;
+	struct ocelot_port *ocelot_port = ocelot->ports[port];
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+
+	if (state->interface != PHY_INTERFACE_MODE_NA &&
+	    state->interface != ocelot_port->phy_mode) {
+		bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
+		return;
+	}
+
+	/* No half-duplex. */
+	phylink_set_port_modes(mask);
+	phylink_set(mask, Autoneg);
+	phylink_set(mask, Pause);
+	phylink_set(mask, Asym_Pause);
+	if (state->interface != PHY_INTERFACE_MODE_2500BASEX) {
+		phylink_set(mask, 10baseT_Full);
+		phylink_set(mask, 100baseT_Full);
+		phylink_set(mask, 1000baseT_Full);
+	}
+	/* The internal ports that run at 2.5G are overclocked GMII */
+	if (state->interface == PHY_INTERFACE_MODE_GMII ||
+	    state->interface == PHY_INTERFACE_MODE_2500BASEX ||
+	    state->interface == PHY_INTERFACE_MODE_USXGMII) {
+		phylink_set(mask, 2500baseT_Full);
+		phylink_set(mask, 2500baseX_Full);
+	}
+
+	bitmap_and(supported, supported, mask,
+		   __ETHTOOL_LINK_MODE_MASK_NBITS);
+	bitmap_and(state->advertising, state->advertising, mask,
+		   __ETHTOOL_LINK_MODE_MASK_NBITS);
+}
+
+static int felix_phylink_mac_pcs_get_state(struct dsa_switch *ds, int port,
+					   struct phylink_link_state *state)
+{
+	struct ocelot *ocelot = ds->priv;
+	struct felix *felix = ocelot_to_felix(ocelot);
+
+	if (felix->info->pcs_link_state)
+		felix->info->pcs_link_state(ocelot, port, state);
+
+	return 0;
+}
+
+static void felix_phylink_mac_config(struct dsa_switch *ds, int port,
+				     unsigned int link_an_mode,
+				     const struct phylink_link_state *state)
+{
+	struct ocelot *ocelot = ds->priv;
+	struct ocelot_port *ocelot_port = ocelot->ports[port];
+	struct felix *felix = ocelot_to_felix(ocelot);
+	u32 mac_fc_cfg;
+
+	/* Take port out of reset by clearing the MAC_TX_RST, MAC_RX_RST and
+	 * PORT_RST bits in CLOCK_CFG
+	 */
+	ocelot_port_writel(ocelot_port, DEV_CLOCK_CFG_LINK_SPEED(state->speed),
+			   DEV_CLOCK_CFG);
+
+	/* Flow control. Link speed is only used here to evaluate the time
+	 * specification in incoming pause frames.
+	 */
+	mac_fc_cfg = SYS_MAC_FC_CFG_FC_LINK_SPEED(state->speed);
+	if (state->pause & MLO_PAUSE_RX)
+		mac_fc_cfg |= SYS_MAC_FC_CFG_RX_FC_ENA;
+	if (state->pause & MLO_PAUSE_TX)
+		mac_fc_cfg |= SYS_MAC_FC_CFG_TX_FC_ENA |
+			      SYS_MAC_FC_CFG_PAUSE_VAL_CFG(0xffff) |
+			      SYS_MAC_FC_CFG_FC_LATENCY_CFG(0x7) |
+			      SYS_MAC_FC_CFG_ZERO_PAUSE_ENA;
+	ocelot_write_rix(ocelot, mac_fc_cfg, SYS_MAC_FC_CFG, port);
+
+	ocelot_write_rix(ocelot, 0, ANA_POL_FLOWC, port);
+
+	if (felix->info->pcs_init)
+		felix->info->pcs_init(ocelot, port, link_an_mode, state);
+}
+
+static void felix_phylink_mac_an_restart(struct dsa_switch *ds, int port)
+{
+	struct ocelot *ocelot = ds->priv;
+	struct felix *felix = ocelot_to_felix(ocelot);
+
+	if (felix->info->pcs_an_restart)
+		felix->info->pcs_an_restart(ocelot, port);
+}
+
+static void felix_phylink_mac_link_down(struct dsa_switch *ds, int port,
+					unsigned int link_an_mode,
+					phy_interface_t interface)
+{
+	struct ocelot *ocelot = ds->priv;
+	struct ocelot_port *ocelot_port = ocelot->ports[port];
+
+	ocelot_port_writel(ocelot_port, 0, DEV_MAC_ENA_CFG);
+	ocelot_rmw_rix(ocelot, 0, QSYS_SWITCH_PORT_MODE_PORT_ENA,
+		       QSYS_SWITCH_PORT_MODE, port);
+}
+
+static void felix_phylink_mac_link_up(struct dsa_switch *ds, int port,
+				      unsigned int link_an_mode,
+				      phy_interface_t interface,
+				      struct phy_device *phydev)
+{
+	struct ocelot *ocelot = ds->priv;
+	struct ocelot_port *ocelot_port = ocelot->ports[port];
+
+	/* Enable MAC module */
+	ocelot_port_writel(ocelot_port, DEV_MAC_ENA_CFG_RX_ENA |
+			   DEV_MAC_ENA_CFG_TX_ENA, DEV_MAC_ENA_CFG);
+
+	/* Enable receiving frames on the port, and activate auto-learning of
+	 * MAC addresses.
+	 */
+	ocelot_write_gix(ocelot, ANA_PORT_PORT_CFG_LEARNAUTO |
+			 ANA_PORT_PORT_CFG_RECV_ENA |
+			 ANA_PORT_PORT_CFG_PORTID_VAL(port),
+			 ANA_PORT_PORT_CFG, port);
+
+	/* Core: Enable port for frame transfer */
+	ocelot_write_rix(ocelot, QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE |
+			 QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG(1) |
+			 QSYS_SWITCH_PORT_MODE_PORT_ENA,
+			 QSYS_SWITCH_PORT_MODE, port);
+}
+
 static void felix_get_strings(struct dsa_switch *ds, int port,
 			      u32 stringset, u8 *data)
 {
@@ -185,10 +314,76 @@ static int felix_get_ts_info(struct dsa_switch *ds, int port,
 	return ocelot_get_ts_info(ocelot, port, info);
 }
 
+static int felix_parse_ports_node(struct felix *felix,
+				  struct device_node *ports_node,
+				  phy_interface_t *port_phy_modes)
+{
+	struct ocelot *ocelot = &felix->ocelot;
+	struct device *dev = felix->ocelot.dev;
+	struct device_node *child;
+
+	for_each_child_of_node(ports_node, child) {
+		phy_interface_t phy_mode;
+		u32 port;
+		int err;
+
+		/* Get switch port number from DT */
+		if (of_property_read_u32(child, "reg", &port) < 0) {
+			dev_err(dev, "Port number not defined in device tree "
+				"(property \"reg\")\n");
+			of_node_put(child);
+			return -ENODEV;
+		}
+
+		/* Get PHY mode from DT */
+		err = of_get_phy_mode(child, &phy_mode);
+		if (err) {
+			dev_err(dev, "Failed to read phy-mode or "
+				"phy-interface-type property for port %d\n",
+				port);
+			of_node_put(child);
+			return -ENODEV;
+		}
+
+		err = felix->info->prevalidate_phy_mode(ocelot, port, phy_mode);
+		if (err < 0) {
+			dev_err(dev, "Unsupported PHY mode %s on port %d\n",
+				phy_modes(phy_mode), port);
+			return err;
+		}
+
+		port_phy_modes[port] = phy_mode;
+	}
+
+	return 0;
+}
+
+static int felix_parse_dt(struct felix *felix, phy_interface_t *port_phy_modes)
+{
+	struct device *dev = felix->ocelot.dev;
+	struct device_node *switch_node;
+	struct device_node *ports_node;
+	int err;
+
+	switch_node = dev->of_node;
+
+	ports_node = of_get_child_by_name(switch_node, "ports");
+	if (!ports_node) {
+		dev_err(dev, "Incorrect bindings: absent \"ports\" node\n");
+		return -ENODEV;
+	}
+
+	err = felix_parse_ports_node(felix, ports_node, port_phy_modes);
+	of_node_put(ports_node);
+
+	return err;
+}
+
 static int felix_init_structs(struct felix *felix, int num_phys_ports)
 {
 	struct ocelot *ocelot = &felix->ocelot;
-	resource_size_t base;
+	phy_interface_t *port_phy_modes;
+	resource_size_t switch_base;
 	int port, i, err;
 
 	ocelot->num_phys_ports = num_phys_ports;
@@ -203,7 +398,19 @@ static int felix_init_structs(struct felix *felix, int num_phys_ports)
 	ocelot->shared_queue_sz	= felix->info->shared_queue_sz;
 	ocelot->ops		= felix->info->ops;
 
-	base = pci_resource_start(felix->pdev, felix->info->pci_bar);
+	port_phy_modes = kcalloc(num_phys_ports, sizeof(phy_interface_t),
+				 GFP_KERNEL);
+	if (!port_phy_modes)
+		return -ENOMEM;
+
+	err = felix_parse_dt(felix, port_phy_modes);
+	if (err) {
+		kfree(port_phy_modes);
+		return err;
+	}
+
+	switch_base = pci_resource_start(felix->pdev,
+					 felix->info->switch_pci_bar);
 
 	for (i = 0; i < TARGET_MAX; i++) {
 		struct regmap *target;
@@ -214,13 +421,14 @@ static int felix_init_structs(struct felix *felix, int num_phys_ports)
 
 		res = &felix->info->target_io_res[i];
 		res->flags = IORESOURCE_MEM;
-		res->start += base;
-		res->end += base;
+		res->start += switch_base;
+		res->end += switch_base;
 
 		target = ocelot_regmap_init(ocelot, res);
 		if (IS_ERR(target)) {
 			dev_err(ocelot->dev,
 				"Failed to map device memory space\n");
+			kfree(port_phy_modes);
 			return PTR_ERR(target);
 		}
 
@@ -230,6 +438,7 @@ static int felix_init_structs(struct felix *felix, int num_phys_ports)
 	err = ocelot_regfields_init(ocelot, felix->info->regfields);
 	if (err) {
 		dev_err(ocelot->dev, "failed to init reg fields map\n");
+		kfree(port_phy_modes);
 		return err;
 	}
 
@@ -244,26 +453,37 @@ static int felix_init_structs(struct felix *felix, int num_phys_ports)
 		if (!ocelot_port) {
 			dev_err(ocelot->dev,
 				"failed to allocate port memory\n");
+			kfree(port_phy_modes);
 			return -ENOMEM;
 		}
 
 		res = &felix->info->port_io_res[port];
 		res->flags = IORESOURCE_MEM;
-		res->start += base;
-		res->end += base;
+		res->start += switch_base;
+		res->end += switch_base;
 
 		port_regs = devm_ioremap_resource(ocelot->dev, res);
 		if (IS_ERR(port_regs)) {
 			dev_err(ocelot->dev,
 				"failed to map registers for port %d\n", port);
+			kfree(port_phy_modes);
 			return PTR_ERR(port_regs);
 		}
 
+		ocelot_port->phy_mode = port_phy_modes[port];
 		ocelot_port->ocelot = ocelot;
 		ocelot_port->regs = port_regs;
 		ocelot->ports[port] = ocelot_port;
 	}
 
+	kfree(port_phy_modes);
+
+	if (felix->info->mdio_bus_alloc) {
+		err = felix->info->mdio_bus_alloc(ocelot);
+		if (err < 0)
+			return err;
+	}
+
 	return 0;
 }
 
@@ -293,12 +513,22 @@ static int felix_setup(struct dsa_switch *ds)
 					    OCELOT_TAG_PREFIX_LONG);
 	}
 
+	/* It looks like the MAC/PCS interrupt register - PM0_IEVENT (0x8040)
+	 * isn't instantiated for the Felix PF.
+	 * In-band AN may take a few ms to complete, so we need to poll.
+	 */
+	ds->pcs_poll = true;
+
 	return 0;
 }
 
 static void felix_teardown(struct dsa_switch *ds)
 {
 	struct ocelot *ocelot = ds->priv;
+	struct felix *felix = ocelot_to_felix(ocelot);
+
+	if (felix->info->mdio_bus_free)
+		felix->info->mdio_bus_free(ocelot);
 
 	/* stop workqueue thread */
 	ocelot_deinit(ocelot);
@@ -369,7 +599,12 @@ static const struct dsa_switch_ops felix_switch_ops = {
 	.get_ethtool_stats	= felix_get_ethtool_stats,
 	.get_sset_count		= felix_get_sset_count,
 	.get_ts_info		= felix_get_ts_info,
-	.adjust_link		= felix_adjust_link,
+	.phylink_validate	= felix_phylink_validate,
+	.phylink_mac_link_state	= felix_phylink_mac_pcs_get_state,
+	.phylink_mac_config	= felix_phylink_mac_config,
+	.phylink_mac_an_restart	= felix_phylink_mac_an_restart,
+	.phylink_mac_link_down	= felix_phylink_mac_link_down,
+	.phylink_mac_link_up	= felix_phylink_mac_link_up,
 	.port_enable		= felix_port_enable,
 	.port_disable		= felix_port_disable,
 	.port_fdb_dump		= felix_fdb_dump,
diff --git a/drivers/net/dsa/ocelot/felix.h b/drivers/net/dsa/ocelot/felix.h
index 204296e51d0c..3a7580015b62 100644
--- a/drivers/net/dsa/ocelot/felix.h
+++ b/drivers/net/dsa/ocelot/felix.h
@@ -10,6 +10,7 @@
 struct felix_info {
 	struct resource			*target_io_res;
 	struct resource			*port_io_res;
+	struct resource			*imdio_res;
 	const struct reg_field		*regfields;
 	const u32 *const		*map;
 	const struct ocelot_ops		*ops;
@@ -17,7 +18,18 @@ struct felix_info {
 	const struct ocelot_stat_layout	*stats_layout;
 	unsigned int			num_stats;
 	int				num_ports;
-	int				pci_bar;
+	int				switch_pci_bar;
+	int				imdio_pci_bar;
+	int	(*mdio_bus_alloc)(struct ocelot *ocelot);
+	void	(*mdio_bus_free)(struct ocelot *ocelot);
+	void	(*pcs_init)(struct ocelot *ocelot, int port,
+			    unsigned int link_an_mode,
+			    const struct phylink_link_state *state);
+	void	(*pcs_an_restart)(struct ocelot *ocelot, int port);
+	void	(*pcs_link_state)(struct ocelot *ocelot, int port,
+				  struct phylink_link_state *state);
+	int	(*prevalidate_phy_mode)(struct ocelot *ocelot, int port,
+					phy_interface_t phy_mode);
 };
 
 extern struct felix_info		felix_info_vsc9959;
@@ -32,6 +44,8 @@ struct felix {
 	struct pci_dev			*pdev;
 	struct felix_info		*info;
 	struct ocelot			ocelot;
+	struct mii_bus			*imdio;
+	struct phy_device		**pcs;
 };
 
 #endif
diff --git a/drivers/net/dsa/ocelot/felix_vsc9959.c b/drivers/net/dsa/ocelot/felix_vsc9959.c
index b9758b0d18c7..03482616faa7 100644
--- a/drivers/net/dsa/ocelot/felix_vsc9959.c
+++ b/drivers/net/dsa/ocelot/felix_vsc9959.c
@@ -2,12 +2,33 @@
 /* Copyright 2017 Microsemi Corporation
  * Copyright 2018-2019 NXP Semiconductors
  */
+#include <linux/fsl/enetc_mdio.h>
 #include <soc/mscc/ocelot_sys.h>
 #include <soc/mscc/ocelot.h>
 #include <linux/iopoll.h>
 #include <linux/pci.h>
 #include "felix.h"
 
+/* TODO: should find a better place for these */
+#define USXGMII_BMCR_RESET		BIT(15)
+#define USXGMII_BMCR_AN_EN		BIT(12)
+#define USXGMII_BMCR_RST_AN		BIT(9)
+#define USXGMII_BMSR_LNKS(status)	(((status) & GENMASK(2, 2)) >> 2)
+#define USXGMII_BMSR_AN_CMPL(status)	(((status) & GENMASK(5, 5)) >> 5)
+#define USXGMII_ADVERTISE_LNKS(x)	(((x) << 15) & BIT(15))
+#define USXGMII_ADVERTISE_FDX		BIT(12)
+#define USXGMII_ADVERTISE_SPEED(x)	(((x) << 9) & GENMASK(11, 9))
+#define USXGMII_LPA_LNKS(lpa)		((lpa) >> 15)
+#define USXGMII_LPA_DUPLEX(lpa)		(((lpa) & GENMASK(12, 12)) >> 12)
+#define USXGMII_LPA_SPEED(lpa)		(((lpa) & GENMASK(11, 9)) >> 9)
+
+enum usxgmii_speed {
+	USXGMII_SPEED_10	= 0,
+	USXGMII_SPEED_100	= 1,
+	USXGMII_SPEED_1000	= 2,
+	USXGMII_SPEED_2500	= 4,
+};
+
 static const u32 vsc9959_ana_regmap[] = {
 	REG(ANA_ADVLEARN,			0x0089a0),
 	REG(ANA_VLANMASK,			0x0089a4),
@@ -386,6 +407,15 @@ static struct resource vsc9959_port_io_res[] = {
 	},
 };
 
+/* Port MAC 0 Internal MDIO bus through which the SerDes acting as an
+ * SGMII/QSGMII MAC PCS can be found.
+ */
+static struct resource vsc9959_imdio_res = {
+	.start		= 0x8030,
+	.end		= 0x8040,
+	.name		= "imdio",
+};
+
 static const struct reg_field vsc9959_regfields[] = {
 	[ANA_ADVLEARN_VLAN_CHK] = REG_FIELD(ANA_ADVLEARN, 6, 6),
 	[ANA_ADVLEARN_LEARN_MIRROR] = REG_FIELD(ANA_ADVLEARN, 0, 5),
@@ -565,13 +595,475 @@ static int vsc9959_reset(struct ocelot *ocelot)
 	return 0;
 }
 
+static void vsc9959_pcs_an_restart_sgmii(struct phy_device *pcs)
+{
+	phy_set_bits(pcs, MII_BMCR, BMCR_ANRESTART);
+}
+
+static void vsc9959_pcs_an_restart_usxgmii(struct phy_device *pcs)
+{
+	phy_write_mmd(pcs, MDIO_MMD_VEND2, MII_BMCR,
+		      USXGMII_BMCR_RESET |
+		      USXGMII_BMCR_AN_EN |
+		      USXGMII_BMCR_RST_AN);
+}
+
+static void vsc9959_pcs_an_restart(struct ocelot *ocelot, int port)
+{
+	struct felix *felix = ocelot_to_felix(ocelot);
+	struct phy_device *pcs = felix->pcs[port];
+
+	if (!pcs)
+		return;
+
+	switch (pcs->interface) {
+	case PHY_INTERFACE_MODE_SGMII:
+	case PHY_INTERFACE_MODE_QSGMII:
+		vsc9959_pcs_an_restart_sgmii(pcs);
+		break;
+	case PHY_INTERFACE_MODE_USXGMII:
+		vsc9959_pcs_an_restart_usxgmii(pcs);
+		break;
+	default:
+		dev_err(ocelot->dev, "Invalid PCS interface type %s\n",
+			phy_modes(pcs->interface));
+		break;
+	}
+}
+
+/* We enable SGMII AN only when the PHY has managed = "in-band-status" in the
+ * device tree. If we are in MLO_AN_PHY mode, we program directly state->speed
+ * into the PCS, which is retrieved out-of-band over MDIO. This also has the
+ * benefit of working with SGMII fixed-links, like downstream switches, where
+ * both link partners attempt to operate as AN slaves and therefore AN never
+ * completes.  But it also has the disadvantage that some PHY chips don't pass
+ * traffic if SGMII AN is enabled but not completed (acknowledged by us), so
+ * setting MLO_AN_INBAND is actually required for those.
+ */
+static void vsc9959_pcs_init_sgmii(struct phy_device *pcs,
+				   unsigned int link_an_mode,
+				   const struct phylink_link_state *state)
+{
+	if (link_an_mode == MLO_AN_INBAND) {
+		/* SGMII spec requires tx_config_Reg[15:0] to be exactly 0x4001
+		 * for the MAC PCS in order to acknowledge the AN.
+		 */
+		phy_write(pcs, MII_ADVERTISE, ADVERTISE_SGMII |
+					      ADVERTISE_LPACK);
+
+		phy_write(pcs, ENETC_PCS_IF_MODE,
+			  ENETC_PCS_IF_MODE_SGMII_EN |
+			  ENETC_PCS_IF_MODE_USE_SGMII_AN);
+
+		/* Adjust link timer for SGMII */
+		phy_write(pcs, ENETC_PCS_LINK_TIMER1,
+			  ENETC_PCS_LINK_TIMER1_VAL);
+		phy_write(pcs, ENETC_PCS_LINK_TIMER2,
+			  ENETC_PCS_LINK_TIMER2_VAL);
+
+		phy_write(pcs, MII_BMCR, BMCR_ANRESTART | BMCR_ANENABLE);
+	} else {
+		int speed;
+
+		if (state->duplex == DUPLEX_HALF) {
+			phydev_err(pcs, "Half duplex not supported\n");
+			return;
+		}
+		switch (state->speed) {
+		case SPEED_1000:
+			speed = ENETC_PCS_SPEED_1000;
+			break;
+		case SPEED_100:
+			speed = ENETC_PCS_SPEED_100;
+			break;
+		case SPEED_10:
+			speed = ENETC_PCS_SPEED_10;
+			break;
+		case SPEED_UNKNOWN:
+			/* Silently don't do anything */
+			return;
+		default:
+			phydev_err(pcs, "Invalid PCS speed %d\n", state->speed);
+			return;
+		}
+
+		phy_write(pcs, ENETC_PCS_IF_MODE,
+			  ENETC_PCS_IF_MODE_SGMII_EN |
+			  ENETC_PCS_IF_MODE_SGMII_SPEED(speed));
+
+		/* Yes, not a mistake: speed is given by IF_MODE. */
+		phy_write(pcs, MII_BMCR, BMCR_RESET |
+					 BMCR_SPEED1000 |
+					 BMCR_FULLDPLX);
+	}
+}
+
+/* 2500Base-X is SerDes protocol 7 on Felix and 6 on ENETC. It is a SerDes lane
+ * clocked at 3.125 GHz which encodes symbols with 8b/10b and does not have
+ * auto-negotiation of any link parameters. Electrically it is compatible with
+ * a single lane of XAUI.
+ * The hardware reference manual wants to call this mode SGMII, but it isn't
+ * really, since the fundamental features of SGMII:
+ * - Downgrading the link speed by duplicating symbols
+ * - Auto-negotiation
+ * are not there.
+ * The speed is configured at 1000 in the IF_MODE and BMCR MDIO registers
+ * because the clock frequency is actually given by a PLL configured in the
+ * Reset Configuration Word (RCW).
+ * Since there is no difference between fixed speed SGMII w/o AN and 802.3z w/o
+ * AN, we call this PHY interface type 2500Base-X. In case a PHY negotiates a
+ * lower link speed on line side, the system-side interface remains fixed at
+ * 2500 Mbps and we do rate adaptation through pause frames.
+ */
+static void vsc9959_pcs_init_2500basex(struct phy_device *pcs,
+				       unsigned int link_an_mode,
+				       const struct phylink_link_state *state)
+{
+	if (link_an_mode == MLO_AN_INBAND) {
+		phydev_err(pcs, "AN not supported on 3.125GHz SerDes lane\n");
+		return;
+	}
+
+	phy_write(pcs, ENETC_PCS_IF_MODE,
+		  ENETC_PCS_IF_MODE_SGMII_EN |
+		  ENETC_PCS_IF_MODE_SGMII_SPEED(ENETC_PCS_SPEED_2500));
+
+	phy_write(pcs, MII_BMCR, BMCR_SPEED1000 |
+				 BMCR_FULLDPLX |
+				 BMCR_RESET);
+}
+
+static void vsc9959_pcs_init_usxgmii(struct phy_device *pcs,
+				     unsigned int link_an_mode,
+				     const struct phylink_link_state *state)
+{
+	if (link_an_mode != MLO_AN_INBAND) {
+		phydev_err(pcs, "USXGMII only supports in-band AN for now\n");
+		return;
+	}
+
+	/* Configure device ability for the USXGMII Replicator */
+	phy_write_mmd(pcs, MDIO_MMD_VEND2, MII_ADVERTISE,
+		      USXGMII_ADVERTISE_SPEED(USXGMII_SPEED_2500) |
+		      USXGMII_ADVERTISE_LNKS(1) |
+		      ADVERTISE_SGMII |
+		      ADVERTISE_LPACK |
+		      USXGMII_ADVERTISE_FDX);
+}
+
+static void vsc9959_pcs_init(struct ocelot *ocelot, int port,
+			     unsigned int link_an_mode,
+			     const struct phylink_link_state *state)
+{
+	struct felix *felix = ocelot_to_felix(ocelot);
+	struct phy_device *pcs = felix->pcs[port];
+
+	if (!pcs)
+		return;
+
+	/* The PCS does not implement the BMSR register fully, so capability
+	 * detection via genphy_read_abilities does not work. Since we can get
+	 * the PHY config word from the LPA register though, there is still
+	 * value in using the generic phy_resolve_aneg_linkmode function. So
+	 * populate the supported and advertising link modes manually here.
+	 */
+	linkmode_set_bit_array(phy_basic_ports_array,
+			       ARRAY_SIZE(phy_basic_ports_array),
+			       pcs->supported);
+	linkmode_set_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT, pcs->supported);
+	linkmode_set_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT, pcs->supported);
+	linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT, pcs->supported);
+	if (pcs->interface == PHY_INTERFACE_MODE_2500BASEX ||
+	    pcs->interface == PHY_INTERFACE_MODE_USXGMII)
+		linkmode_set_bit(ETHTOOL_LINK_MODE_2500baseX_Full_BIT,
+				 pcs->supported);
+	if (pcs->interface != PHY_INTERFACE_MODE_2500BASEX)
+		linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
+				 pcs->supported);
+	phy_advertise_supported(pcs);
+
+	switch (pcs->interface) {
+	case PHY_INTERFACE_MODE_SGMII:
+	case PHY_INTERFACE_MODE_QSGMII:
+		vsc9959_pcs_init_sgmii(pcs, link_an_mode, state);
+		break;
+	case PHY_INTERFACE_MODE_2500BASEX:
+		vsc9959_pcs_init_2500basex(pcs, link_an_mode, state);
+		break;
+	case PHY_INTERFACE_MODE_USXGMII:
+		vsc9959_pcs_init_usxgmii(pcs, link_an_mode, state);
+		break;
+	default:
+		dev_err(ocelot->dev, "Unsupported link mode %s\n",
+			phy_modes(pcs->interface));
+	}
+}
+
+static void vsc9959_pcs_link_state_resolve(struct phy_device *pcs,
+					   struct phylink_link_state *state)
+{
+	state->an_complete = pcs->autoneg_complete;
+	state->an_enabled = pcs->autoneg;
+	state->link = pcs->link;
+	state->duplex = pcs->duplex;
+	state->speed = pcs->speed;
+	/* SGMII AN does not negotiate flow control, but that's ok,
+	 * since phylink already knows that, and does:
+	 *	link_state.pause |= pl->phy_state.pause;
+	 */
+	state->pause = MLO_PAUSE_NONE;
+
+	phydev_dbg(pcs,
+		   "mode=%s/%s/%s adv=%*pb lpa=%*pb link=%u an_enabled=%u an_complete=%u\n",
+		   phy_modes(pcs->interface),
+		   phy_speed_to_str(pcs->speed),
+		   phy_duplex_to_str(pcs->duplex),
+		   __ETHTOOL_LINK_MODE_MASK_NBITS, pcs->advertising,
+		   __ETHTOOL_LINK_MODE_MASK_NBITS, pcs->lp_advertising,
+		   pcs->link, pcs->autoneg, pcs->autoneg_complete);
+}
+
+static void vsc9959_pcs_link_state_sgmii(struct phy_device *pcs,
+					 struct phylink_link_state *state)
+{
+	int err;
+
+	err = genphy_update_link(pcs);
+	if (err < 0)
+		return;
+
+	if (pcs->autoneg_complete) {
+		u16 lpa = phy_read(pcs, MII_LPA);
+
+		mii_lpa_to_linkmode_lpa_sgmii(pcs->lp_advertising, lpa);
+
+		phy_resolve_aneg_linkmode(pcs);
+	}
+}
+
+static void vsc9959_pcs_link_state_2500basex(struct phy_device *pcs,
+					     struct phylink_link_state *state)
+{
+	int err;
+
+	err = genphy_update_link(pcs);
+	if (err < 0)
+		return;
+
+	pcs->speed = SPEED_2500;
+	pcs->asym_pause = true;
+	pcs->pause = true;
+}
+
+static void vsc9959_pcs_link_state_usxgmii(struct phy_device *pcs,
+					   struct phylink_link_state *state)
+{
+	int status, lpa;
+
+	status = phy_read_mmd(pcs, MDIO_MMD_VEND2, MII_BMSR);
+	if (status < 0)
+		return;
+
+	pcs->autoneg = true;
+	pcs->autoneg_complete = USXGMII_BMSR_AN_CMPL(status);
+	pcs->link = USXGMII_BMSR_LNKS(status);
+
+	if (!pcs->link || !pcs->autoneg_complete)
+		return;
+
+	lpa = phy_read_mmd(pcs, MDIO_MMD_VEND2, MII_LPA);
+	if (lpa < 0)
+		return;
+
+	switch (USXGMII_LPA_SPEED(lpa)) {
+	case USXGMII_SPEED_10:
+		pcs->speed = SPEED_10;
+		break;
+	case USXGMII_SPEED_100:
+		pcs->speed = SPEED_100;
+		break;
+	case USXGMII_SPEED_1000:
+		pcs->speed = SPEED_1000;
+		break;
+	case USXGMII_SPEED_2500:
+		pcs->speed = SPEED_2500;
+		break;
+	default:
+		break;
+	}
+
+	pcs->link = USXGMII_LPA_LNKS(lpa);
+	if (USXGMII_LPA_DUPLEX(lpa))
+		pcs->duplex = DUPLEX_FULL;
+	else
+		pcs->duplex = DUPLEX_HALF;
+}
+
+static void vsc9959_pcs_link_state(struct ocelot *ocelot, int port,
+				   struct phylink_link_state *state)
+{
+	struct felix *felix = ocelot_to_felix(ocelot);
+	struct phy_device *pcs = felix->pcs[port];
+
+	if (!pcs)
+		return;
+
+	pcs->speed = SPEED_UNKNOWN;
+	pcs->duplex = DUPLEX_UNKNOWN;
+	pcs->pause = 0;
+	pcs->asym_pause = 0;
+
+	switch (pcs->interface) {
+	case PHY_INTERFACE_MODE_SGMII:
+	case PHY_INTERFACE_MODE_QSGMII:
+		vsc9959_pcs_link_state_sgmii(pcs, state);
+		break;
+	case PHY_INTERFACE_MODE_2500BASEX:
+		vsc9959_pcs_link_state_2500basex(pcs, state);
+		break;
+	case PHY_INTERFACE_MODE_USXGMII:
+		vsc9959_pcs_link_state_usxgmii(pcs, state);
+		break;
+	default:
+		return;
+	}
+
+	vsc9959_pcs_link_state_resolve(pcs, state);
+}
+
+static int vsc9959_prevalidate_phy_mode(struct ocelot *ocelot, int port,
+					phy_interface_t phy_mode)
+{
+	switch (phy_mode) {
+	case PHY_INTERFACE_MODE_GMII:
+		/* Only supported on internal to-CPU ports */
+		if (port != 4 && port != 5)
+			return -ENOTSUPP;
+		return 0;
+	case PHY_INTERFACE_MODE_SGMII:
+	case PHY_INTERFACE_MODE_QSGMII:
+	case PHY_INTERFACE_MODE_USXGMII:
+	case PHY_INTERFACE_MODE_2500BASEX:
+		/* Not supported on internal to-CPU ports */
+		if (port == 4 || port == 5)
+			return -ENOTSUPP;
+		return 0;
+	default:
+		return -ENOTSUPP;
+	}
+}
+
 static const struct ocelot_ops vsc9959_ops = {
 	.reset			= vsc9959_reset,
 };
 
+static int vsc9959_mdio_bus_alloc(struct ocelot *ocelot)
+{
+	struct felix *felix = ocelot_to_felix(ocelot);
+	struct enetc_mdio_priv *mdio_priv;
+	struct device *dev = ocelot->dev;
+	resource_size_t imdio_base;
+	void __iomem *imdio_regs;
+	struct resource *res;
+	struct enetc_hw *hw;
+	struct mii_bus *bus;
+	int port;
+	int rc;
+
+	felix->pcs = devm_kcalloc(dev, felix->info->num_ports,
+				  sizeof(struct phy_device *),
+				  GFP_KERNEL);
+	if (!felix->pcs) {
+		dev_err(dev, "failed to allocate array for PCS PHYs\n");
+		return -ENOMEM;
+	}
+
+	imdio_base = pci_resource_start(felix->pdev,
+					felix->info->imdio_pci_bar);
+
+	res = felix->info->imdio_res;
+	res->flags = IORESOURCE_MEM;
+	res->start += imdio_base;
+	res->end += imdio_base;
+
+	imdio_regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(imdio_regs)) {
+		dev_err(dev, "failed to map internal MDIO registers\n");
+		return PTR_ERR(imdio_regs);
+	}
+
+	hw = enetc_hw_alloc(dev, imdio_regs);
+	if (IS_ERR(hw)) {
+		dev_err(dev, "failed to allocate ENETC HW structure\n");
+		return PTR_ERR(hw);
+	}
+
+	bus = devm_mdiobus_alloc_size(dev, sizeof(*mdio_priv));
+	if (!bus)
+		return -ENOMEM;
+
+	bus->name = "VSC9959 internal MDIO bus";
+	bus->read = enetc_mdio_read;
+	bus->write = enetc_mdio_write;
+	bus->parent = dev;
+	mdio_priv = bus->priv;
+	mdio_priv->hw = hw;
+	/* This gets added to imdio_regs, which already maps addresses
+	 * starting with the proper offset.
+	 */
+	mdio_priv->mdio_base = 0;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s-imdio", dev_name(dev));
+
+	/* Needed in order to initialize the bus mutex lock */
+	rc = mdiobus_register(bus);
+	if (rc < 0) {
+		dev_err(dev, "failed to register MDIO bus\n");
+		return rc;
+	}
+
+	felix->imdio = bus;
+
+	for (port = 0; port < felix->info->num_ports; port++) {
+		struct ocelot_port *ocelot_port = ocelot->ports[port];
+		struct phy_device *pcs;
+		bool is_c45 = false;
+
+		if (ocelot_port->phy_mode == PHY_INTERFACE_MODE_USXGMII)
+			is_c45 = true;
+
+		pcs = get_phy_device(felix->imdio, port, is_c45);
+		if (IS_ERR(pcs))
+			continue;
+
+		pcs->interface = ocelot_port->phy_mode;
+		felix->pcs[port] = pcs;
+
+		dev_info(dev, "Found PCS at internal MDIO address %d\n", port);
+	}
+
+	return 0;
+}
+
+static void vsc9959_mdio_bus_free(struct ocelot *ocelot)
+{
+	struct felix *felix = ocelot_to_felix(ocelot);
+	int port;
+
+	for (port = 0; port < ocelot->num_phys_ports; port++) {
+		struct phy_device *pcs = felix->pcs[port];
+
+		if (!pcs)
+			continue;
+
+		put_device(&pcs->mdio.dev);
+	}
+	mdiobus_unregister(felix->imdio);
+}
+
 struct felix_info felix_info_vsc9959 = {
 	.target_io_res		= vsc9959_target_io_res,
 	.port_io_res		= vsc9959_port_io_res,
+	.imdio_res		= &vsc9959_imdio_res,
 	.regfields		= vsc9959_regfields,
 	.map			= vsc9959_regmap,
 	.ops			= &vsc9959_ops,
@@ -579,5 +1071,12 @@ struct felix_info felix_info_vsc9959 = {
 	.num_stats		= ARRAY_SIZE(vsc9959_stats_layout),
 	.shared_queue_sz	= 128 * 1024,
 	.num_ports		= 6,
-	.pci_bar		= 4,
+	.switch_pci_bar		= 4,
+	.imdio_pci_bar		= 0,
+	.mdio_bus_alloc		= vsc9959_mdio_bus_alloc,
+	.mdio_bus_free		= vsc9959_mdio_bus_free,
+	.pcs_init		= vsc9959_pcs_init,
+	.pcs_an_restart		= vsc9959_pcs_an_restart,
+	.pcs_link_state		= vsc9959_pcs_link_state,
+	.prevalidate_phy_mode	= vsc9959_prevalidate_phy_mode,
 };
diff --git a/drivers/net/ethernet/freescale/enetc/Kconfig b/drivers/net/ethernet/freescale/enetc/Kconfig
index edad4ca46327..fe942de19597 100644
--- a/drivers/net/ethernet/freescale/enetc/Kconfig
+++ b/drivers/net/ethernet/freescale/enetc/Kconfig
@@ -2,6 +2,7 @@
 config FSL_ENETC
 	tristate "ENETC PF driver"
 	depends on PCI && PCI_MSI && (ARCH_LAYERSCAPE || COMPILE_TEST)
+	select FSL_ENETC_MDIO
 	select PHYLIB
 	help
 	  This driver supports NXP ENETC gigabit ethernet controller PCIe
diff --git a/drivers/net/ethernet/freescale/enetc/Makefile b/drivers/net/ethernet/freescale/enetc/Makefile
index d0db33e5b6b7..74f7ac253b8b 100644
--- a/drivers/net/ethernet/freescale/enetc/Makefile
+++ b/drivers/net/ethernet/freescale/enetc/Makefile
@@ -3,7 +3,7 @@
 common-objs := enetc.o enetc_cbdr.o enetc_ethtool.o
 
 obj-$(CONFIG_FSL_ENETC) += fsl-enetc.o
-fsl-enetc-y := enetc_pf.o enetc_mdio.o $(common-objs)
+fsl-enetc-y := enetc_pf.o $(common-objs)
 fsl-enetc-$(CONFIG_PCI_IOV) += enetc_msg.o
 fsl-enetc-$(CONFIG_FSL_ENETC_QOS) += enetc_qos.o
 
diff --git a/drivers/net/ethernet/freescale/enetc/enetc_hw.h b/drivers/net/ethernet/freescale/enetc/enetc_hw.h
index 8375cd886dba..62554f28ce07 100644
--- a/drivers/net/ethernet/freescale/enetc/enetc_hw.h
+++ b/drivers/net/ethernet/freescale/enetc/enetc_hw.h
@@ -200,6 +200,7 @@ enum enetc_bdr_type {TX, RX};
 #define ENETC_PFPMR		0x1900
 #define ENETC_PFPMR_PMACE	BIT(1)
 #define ENETC_PFPMR_MWLM	BIT(0)
+#define ENETC_EMDIO_BASE	0x1c00
 #define ENETC_PSIUMHFR0(n, err)	(((err) ? 0x1d08 : 0x1d00) + (n) * 0x10)
 #define ENETC_PSIUMHFR1(n)	(0x1d04 + (n) * 0x10)
 #define ENETC_PSIMMHFR0(n, err)	(((err) ? 0x1d00 : 0x1d08) + (n) * 0x10)
diff --git a/drivers/net/ethernet/freescale/enetc/enetc_mdio.c b/drivers/net/ethernet/freescale/enetc/enetc_mdio.c
index 149883c8f0b8..48c32a171afa 100644
--- a/drivers/net/ethernet/freescale/enetc/enetc_mdio.c
+++ b/drivers/net/ethernet/freescale/enetc/enetc_mdio.c
@@ -1,41 +1,56 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
 /* Copyright 2019 NXP */
 
+#include <linux/fsl/enetc_mdio.h>
 #include <linux/mdio.h>
 #include <linux/of_mdio.h>
 #include <linux/iopoll.h>
 #include <linux/of.h>
 
-#include "enetc_mdio.h"
+#include "enetc_pf.h"
 
-#define	ENETC_MDIO_REG_OFFSET	0x1c00
 #define	ENETC_MDIO_CFG	0x0	/* MDIO configuration and status */
 #define	ENETC_MDIO_CTL	0x4	/* MDIO control */
 #define	ENETC_MDIO_DATA	0x8	/* MDIO data */
 #define	ENETC_MDIO_ADDR	0xc	/* MDIO address */
 
-#define enetc_mdio_rd(hw, off) \
-	enetc_port_rd(hw, ENETC_##off + ENETC_MDIO_REG_OFFSET)
-#define enetc_mdio_wr(hw, off, val) \
-	enetc_port_wr(hw, ENETC_##off + ENETC_MDIO_REG_OFFSET, val)
-#define enetc_mdio_rd_reg(off)	enetc_mdio_rd(hw, off)
+static inline u32 _enetc_mdio_rd(struct enetc_mdio_priv *mdio_priv, int off)
+{
+	return enetc_port_rd(mdio_priv->hw, mdio_priv->mdio_base + off);
+}
 
-#define ENETC_MDC_DIV		258
+static inline void _enetc_mdio_wr(struct enetc_mdio_priv *mdio_priv, int off,
+				  u32 val)
+{
+	enetc_port_wr(mdio_priv->hw, mdio_priv->mdio_base + off, val);
+}
+
+#define enetc_mdio_rd(mdio_priv, off) \
+	_enetc_mdio_rd(mdio_priv, ENETC_##off)
+#define enetc_mdio_wr(mdio_priv, off, val) \
+	_enetc_mdio_wr(mdio_priv, ENETC_##off, val)
+#define enetc_mdio_rd_reg(off)	enetc_mdio_rd(mdio_priv, off)
 
 #define MDIO_CFG_CLKDIV(x)	((((x) >> 1) & 0xff) << 8)
 #define MDIO_CFG_BSY		BIT(0)
 #define MDIO_CFG_RD_ER		BIT(1)
+#define MDIO_CFG_HOLD(x)	(((x) << 2) & GENMASK(4, 2))
 #define MDIO_CFG_ENC45		BIT(6)
  /* external MDIO only - driven on neg MDC edge */
 #define MDIO_CFG_NEG		BIT(23)
 
+#define ENETC_EMDIO_CFG \
+	(MDIO_CFG_HOLD(2) | \
+	 MDIO_CFG_CLKDIV(258) | \
+	 MDIO_CFG_NEG)
+
 #define MDIO_CTL_DEV_ADDR(x)	((x) & 0x1f)
 #define MDIO_CTL_PORT_ADDR(x)	(((x) & 0x1f) << 5)
 #define MDIO_CTL_READ		BIT(15)
 #define MDIO_DATA(x)		((x) & 0xffff)
 
 #define TIMEOUT	1000
-static int enetc_mdio_wait_complete(struct enetc_hw *hw)
+static int enetc_mdio_wait_complete(struct enetc_mdio_priv *mdio_priv)
 {
 	u32 val;
 
@@ -46,12 +61,11 @@ static int enetc_mdio_wait_complete(struct enetc_hw *hw)
 int enetc_mdio_write(struct mii_bus *bus, int phy_id, int regnum, u16 value)
 {
 	struct enetc_mdio_priv *mdio_priv = bus->priv;
-	struct enetc_hw *hw = mdio_priv->hw;
 	u32 mdio_ctl, mdio_cfg;
 	u16 dev_addr;
 	int ret;
 
-	mdio_cfg = MDIO_CFG_CLKDIV(ENETC_MDC_DIV) | MDIO_CFG_NEG;
+	mdio_cfg = ENETC_EMDIO_CFG;
 	if (regnum & MII_ADDR_C45) {
 		dev_addr = (regnum >> 16) & 0x1f;
 		mdio_cfg |= MDIO_CFG_ENC45;
@@ -61,44 +75,44 @@ int enetc_mdio_write(struct mii_bus *bus, int phy_id, int regnum, u16 value)
 		mdio_cfg &= ~MDIO_CFG_ENC45;
 	}
 
-	enetc_mdio_wr(hw, MDIO_CFG, mdio_cfg);
+	enetc_mdio_wr(mdio_priv, MDIO_CFG, mdio_cfg);
 
-	ret = enetc_mdio_wait_complete(hw);
+	ret = enetc_mdio_wait_complete(mdio_priv);
 	if (ret)
 		return ret;
 
 	/* set port and dev addr */
 	mdio_ctl = MDIO_CTL_PORT_ADDR(phy_id) | MDIO_CTL_DEV_ADDR(dev_addr);
-	enetc_mdio_wr(hw, MDIO_CTL, mdio_ctl);
+	enetc_mdio_wr(mdio_priv, MDIO_CTL, mdio_ctl);
 
 	/* set the register address */
 	if (regnum & MII_ADDR_C45) {
-		enetc_mdio_wr(hw, MDIO_ADDR, regnum & 0xffff);
+		enetc_mdio_wr(mdio_priv, MDIO_ADDR, regnum & 0xffff);
 
-		ret = enetc_mdio_wait_complete(hw);
+		ret = enetc_mdio_wait_complete(mdio_priv);
 		if (ret)
 			return ret;
 	}
 
 	/* write the value */
-	enetc_mdio_wr(hw, MDIO_DATA, MDIO_DATA(value));
+	enetc_mdio_wr(mdio_priv, MDIO_DATA, MDIO_DATA(value));
 
-	ret = enetc_mdio_wait_complete(hw);
+	ret = enetc_mdio_wait_complete(mdio_priv);
 	if (ret)
 		return ret;
 
 	return 0;
 }
+EXPORT_SYMBOL_GPL(enetc_mdio_write);
 
 int enetc_mdio_read(struct mii_bus *bus, int phy_id, int regnum)
 {
 	struct enetc_mdio_priv *mdio_priv = bus->priv;
-	struct enetc_hw *hw = mdio_priv->hw;
 	u32 mdio_ctl, mdio_cfg;
 	u16 dev_addr, value;
 	int ret;
 
-	mdio_cfg = MDIO_CFG_CLKDIV(ENETC_MDC_DIV) | MDIO_CFG_NEG;
+	mdio_cfg = ENETC_EMDIO_CFG;
 	if (regnum & MII_ADDR_C45) {
 		dev_addr = (regnum >> 16) & 0x1f;
 		mdio_cfg |= MDIO_CFG_ENC45;
@@ -107,86 +121,56 @@ int enetc_mdio_read(struct mii_bus *bus, int phy_id, int regnum)
 		mdio_cfg &= ~MDIO_CFG_ENC45;
 	}
 
-	enetc_mdio_wr(hw, MDIO_CFG, mdio_cfg);
+	enetc_mdio_wr(mdio_priv, MDIO_CFG, mdio_cfg);
 
-	ret = enetc_mdio_wait_complete(hw);
+	ret = enetc_mdio_wait_complete(mdio_priv);
 	if (ret)
 		return ret;
 
 	/* set port and device addr */
 	mdio_ctl = MDIO_CTL_PORT_ADDR(phy_id) | MDIO_CTL_DEV_ADDR(dev_addr);
-	enetc_mdio_wr(hw, MDIO_CTL, mdio_ctl);
+	enetc_mdio_wr(mdio_priv, MDIO_CTL, mdio_ctl);
 
 	/* set the register address */
 	if (regnum & MII_ADDR_C45) {
-		enetc_mdio_wr(hw, MDIO_ADDR, regnum & 0xffff);
+		enetc_mdio_wr(mdio_priv, MDIO_ADDR, regnum & 0xffff);
 
-		ret = enetc_mdio_wait_complete(hw);
+		ret = enetc_mdio_wait_complete(mdio_priv);
 		if (ret)
 			return ret;
 	}
 
 	/* initiate the read */
-	enetc_mdio_wr(hw, MDIO_CTL, mdio_ctl | MDIO_CTL_READ);
+	enetc_mdio_wr(mdio_priv, MDIO_CTL, mdio_ctl | MDIO_CTL_READ);
 
-	ret = enetc_mdio_wait_complete(hw);
+	ret = enetc_mdio_wait_complete(mdio_priv);
 	if (ret)
 		return ret;
 
 	/* return all Fs if nothing was there */
-	if (enetc_mdio_rd(hw, MDIO_CFG) & MDIO_CFG_RD_ER) {
+	if (enetc_mdio_rd(mdio_priv, MDIO_CFG) & MDIO_CFG_RD_ER) {
 		dev_dbg(&bus->dev,
 			"Error while reading PHY%d reg at %d.%hhu\n",
 			phy_id, dev_addr, regnum);
 		return 0xffff;
 	}
 
-	value = enetc_mdio_rd(hw, MDIO_DATA) & 0xffff;
+	value = enetc_mdio_rd(mdio_priv, MDIO_DATA) & 0xffff;
 
 	return value;
 }
+EXPORT_SYMBOL_GPL(enetc_mdio_read);
 
-int enetc_mdio_probe(struct enetc_pf *pf)
+struct enetc_hw *enetc_hw_alloc(struct device *dev, void __iomem *port_regs)
 {
-	struct device *dev = &pf->si->pdev->dev;
-	struct enetc_mdio_priv *mdio_priv;
-	struct device_node *np;
-	struct mii_bus *bus;
-	int err;
+	struct enetc_hw *hw;
 
-	bus = devm_mdiobus_alloc_size(dev, sizeof(*mdio_priv));
-	if (!bus)
-		return -ENOMEM;
+	hw = devm_kzalloc(dev, sizeof(*hw), GFP_KERNEL);
+	if (!hw)
+		return ERR_PTR(-ENOMEM);
 
-	bus->name = "Freescale ENETC MDIO Bus";
-	bus->read = enetc_mdio_read;
-	bus->write = enetc_mdio_write;
-	bus->parent = dev;
-	mdio_priv = bus->priv;
-	mdio_priv->hw = &pf->si->hw;
-	snprintf(bus->id, MII_BUS_ID_SIZE, "%s", dev_name(dev));
+	hw->port = port_regs;
 
-	np = of_get_child_by_name(dev->of_node, "mdio");
-	if (!np) {
-		dev_err(dev, "MDIO node missing\n");
-		return -EINVAL;
-	}
-
-	err = of_mdiobus_register(bus, np);
-	if (err) {
-		of_node_put(np);
-		dev_err(dev, "cannot register MDIO bus\n");
-		return err;
-	}
-
-	of_node_put(np);
-	pf->mdio = bus;
-
-	return 0;
-}
-
-void enetc_mdio_remove(struct enetc_pf *pf)
-{
-	if (pf->mdio)
-		mdiobus_unregister(pf->mdio);
+	return hw;
 }
+EXPORT_SYMBOL_GPL(enetc_hw_alloc);
diff --git a/drivers/net/ethernet/freescale/enetc/enetc_mdio.h b/drivers/net/ethernet/freescale/enetc/enetc_mdio.h
deleted file mode 100644
index 60c9a3889824..000000000000
--- a/drivers/net/ethernet/freescale/enetc/enetc_mdio.h
+++ /dev/null
@@ -1,12 +0,0 @@
-/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
-/* Copyright 2019 NXP */
-
-#include <linux/phy.h>
-#include "enetc_pf.h"
-
-struct enetc_mdio_priv {
-	struct enetc_hw *hw;
-};
-
-int enetc_mdio_write(struct mii_bus *bus, int phy_id, int regnum, u16 value);
-int enetc_mdio_read(struct mii_bus *bus, int phy_id, int regnum);
diff --git a/drivers/net/ethernet/freescale/enetc/enetc_pci_mdio.c b/drivers/net/ethernet/freescale/enetc/enetc_pci_mdio.c
index fbd41ce01f06..87c0e969da40 100644
--- a/drivers/net/ethernet/freescale/enetc/enetc_pci_mdio.c
+++ b/drivers/net/ethernet/freescale/enetc/enetc_pci_mdio.c
@@ -1,7 +1,8 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
 /* Copyright 2019 NXP */
+#include <linux/fsl/enetc_mdio.h>
 #include <linux/of_mdio.h>
-#include "enetc_mdio.h"
+#include "enetc_pf.h"
 
 #define ENETC_MDIO_DEV_ID	0xee01
 #define ENETC_MDIO_DEV_NAME	"FSL PCIe IE Central MDIO"
@@ -13,17 +14,29 @@ static int enetc_pci_mdio_probe(struct pci_dev *pdev,
 {
 	struct enetc_mdio_priv *mdio_priv;
 	struct device *dev = &pdev->dev;
+	void __iomem *port_regs;
 	struct enetc_hw *hw;
 	struct mii_bus *bus;
 	int err;
 
-	hw = devm_kzalloc(dev, sizeof(*hw), GFP_KERNEL);
-	if (!hw)
-		return -ENOMEM;
+	port_regs = pci_iomap(pdev, 0, 0);
+	if (!port_regs) {
+		dev_err(dev, "iomap failed\n");
+		err = -ENXIO;
+		goto err_ioremap;
+	}
+
+	hw = enetc_hw_alloc(dev, port_regs);
+	if (IS_ERR(enetc_hw_alloc)) {
+		err = PTR_ERR(hw);
+		goto err_hw_alloc;
+	}
 
 	bus = devm_mdiobus_alloc_size(dev, sizeof(*mdio_priv));
-	if (!bus)
-		return -ENOMEM;
+	if (!bus) {
+		err = -ENOMEM;
+		goto err_mdiobus_alloc;
+	}
 
 	bus->name = ENETC_MDIO_BUS_NAME;
 	bus->read = enetc_mdio_read;
@@ -31,13 +44,14 @@ static int enetc_pci_mdio_probe(struct pci_dev *pdev,
 	bus->parent = dev;
 	mdio_priv = bus->priv;
 	mdio_priv->hw = hw;
+	mdio_priv->mdio_base = ENETC_EMDIO_BASE;
 	snprintf(bus->id, MII_BUS_ID_SIZE, "%s", dev_name(dev));
 
 	pcie_flr(pdev);
 	err = pci_enable_device_mem(pdev);
 	if (err) {
 		dev_err(dev, "device enable failed\n");
-		return err;
+		goto err_pci_enable;
 	}
 
 	err = pci_request_region(pdev, 0, KBUILD_MODNAME);
@@ -46,13 +60,6 @@ static int enetc_pci_mdio_probe(struct pci_dev *pdev,
 		goto err_pci_mem_reg;
 	}
 
-	hw->port = pci_iomap(pdev, 0, 0);
-	if (!hw->port) {
-		err = -ENXIO;
-		dev_err(dev, "iomap failed\n");
-		goto err_ioremap;
-	}
-
 	err = of_mdiobus_register(bus, dev->of_node);
 	if (err)
 		goto err_mdiobus_reg;
@@ -62,12 +69,14 @@ static int enetc_pci_mdio_probe(struct pci_dev *pdev,
 	return 0;
 
 err_mdiobus_reg:
-	iounmap(mdio_priv->hw->port);
-err_ioremap:
 	pci_release_mem_regions(pdev);
 err_pci_mem_reg:
 	pci_disable_device(pdev);
-
+err_pci_enable:
+err_mdiobus_alloc:
+	iounmap(port_regs);
+err_hw_alloc:
+err_ioremap:
 	return err;
 }
 
diff --git a/drivers/net/ethernet/freescale/enetc/enetc_pf.c b/drivers/net/ethernet/freescale/enetc/enetc_pf.c
index e7482d483b28..fc0d7d99e9a1 100644
--- a/drivers/net/ethernet/freescale/enetc/enetc_pf.c
+++ b/drivers/net/ethernet/freescale/enetc/enetc_pf.c
@@ -2,6 +2,7 @@
 /* Copyright 2017-2019 NXP */
 
 #include <linux/module.h>
+#include <linux/fsl/enetc_mdio.h>
 #include <linux/of_mdio.h>
 #include <linux/of_net.h>
 #include "enetc_pf.h"
@@ -749,6 +750,52 @@ static void enetc_pf_netdev_setup(struct enetc_si *si, struct net_device *ndev,
 	enetc_get_primary_mac_addr(&si->hw, ndev->dev_addr);
 }
 
+static int enetc_mdio_probe(struct enetc_pf *pf)
+{
+	struct device *dev = &pf->si->pdev->dev;
+	struct enetc_mdio_priv *mdio_priv;
+	struct device_node *np;
+	struct mii_bus *bus;
+	int err;
+
+	bus = devm_mdiobus_alloc_size(dev, sizeof(*mdio_priv));
+	if (!bus)
+		return -ENOMEM;
+
+	bus->name = "Freescale ENETC MDIO Bus";
+	bus->read = enetc_mdio_read;
+	bus->write = enetc_mdio_write;
+	bus->parent = dev;
+	mdio_priv = bus->priv;
+	mdio_priv->hw = &pf->si->hw;
+	mdio_priv->mdio_base = ENETC_EMDIO_BASE;
+	snprintf(bus->id, MII_BUS_ID_SIZE, "%s", dev_name(dev));
+
+	np = of_get_child_by_name(dev->of_node, "mdio");
+	if (!np) {
+		dev_err(dev, "MDIO node missing\n");
+		return -EINVAL;
+	}
+
+	err = of_mdiobus_register(bus, np);
+	if (err) {
+		of_node_put(np);
+		dev_err(dev, "cannot register MDIO bus\n");
+		return err;
+	}
+
+	of_node_put(np);
+	pf->mdio = bus;
+
+	return 0;
+}
+
+static void enetc_mdio_remove(struct enetc_pf *pf)
+{
+	if (pf->mdio)
+		mdiobus_unregister(pf->mdio);
+}
+
 static int enetc_of_get_phy(struct enetc_ndev_priv *priv)
 {
 	struct enetc_pf *pf = enetc_si_priv(priv->si);
diff --git a/drivers/net/ethernet/freescale/enetc/enetc_pf.h b/drivers/net/ethernet/freescale/enetc/enetc_pf.h
index 10dd1b53bb08..59e65a6f6c3e 100644
--- a/drivers/net/ethernet/freescale/enetc/enetc_pf.h
+++ b/drivers/net/ethernet/freescale/enetc/enetc_pf.h
@@ -49,7 +49,3 @@ struct enetc_pf {
 int enetc_msg_psi_init(struct enetc_pf *pf);
 void enetc_msg_psi_free(struct enetc_pf *pf);
 void enetc_msg_handle_rxmsg(struct enetc_pf *pf, int mbox_id, u16 *status);
-
-/* MDIO */
-int enetc_mdio_probe(struct enetc_pf *pf);
-void enetc_mdio_remove(struct enetc_pf *pf);
diff --git a/drivers/net/ethernet/mscc/ocelot.c b/drivers/net/ethernet/mscc/ocelot.c
index 985b46d7e3d1..86d543ab1ab9 100644
--- a/drivers/net/ethernet/mscc/ocelot.c
+++ b/drivers/net/ethernet/mscc/ocelot.c
@@ -500,13 +500,14 @@ EXPORT_SYMBOL(ocelot_port_enable);
 static int ocelot_port_open(struct net_device *dev)
 {
 	struct ocelot_port_private *priv = netdev_priv(dev);
-	struct ocelot *ocelot = priv->port.ocelot;
+	struct ocelot_port *ocelot_port = &priv->port;
+	struct ocelot *ocelot = ocelot_port->ocelot;
 	int port = priv->chip_port;
 	int err;
 
 	if (priv->serdes) {
 		err = phy_set_mode_ext(priv->serdes, PHY_MODE_ETHERNET,
-				       priv->phy_mode);
+				       ocelot_port->phy_mode);
 		if (err) {
 			netdev_err(dev, "Could not set mode of SerDes\n");
 			return err;
@@ -514,7 +515,7 @@ static int ocelot_port_open(struct net_device *dev)
 	}
 
 	err = phy_connect_direct(dev, priv->phy, &ocelot_port_adjust_link,
-				 priv->phy_mode);
+				 ocelot_port->phy_mode);
 	if (err) {
 		netdev_err(dev, "Could not attach to PHY\n");
 		return err;
diff --git a/drivers/net/ethernet/mscc/ocelot.h b/drivers/net/ethernet/mscc/ocelot.h
index c259114c48fd..04372ba72fec 100644
--- a/drivers/net/ethernet/mscc/ocelot.h
+++ b/drivers/net/ethernet/mscc/ocelot.h
@@ -18,11 +18,11 @@
 #include <linux/ptp_clock_kernel.h>
 #include <linux/regmap.h>
 
+#include <soc/mscc/ocelot_qsys.h>
 #include <soc/mscc/ocelot_sys.h>
+#include <soc/mscc/ocelot_dev.h>
+#include <soc/mscc/ocelot_ana.h>
 #include <soc/mscc/ocelot.h>
-#include "ocelot_ana.h"
-#include "ocelot_dev.h"
-#include "ocelot_qsys.h"
 #include "ocelot_rew.h"
 #include "ocelot_qs.h"
 #include "ocelot_tc.h"
@@ -68,7 +68,6 @@ struct ocelot_port_private {
 
 	u8 vlan_aware;
 
-	phy_interface_t phy_mode;
 	struct phy *serdes;
 
 	struct ocelot_port_tc tc;
diff --git a/drivers/net/ethernet/mscc/ocelot_board.c b/drivers/net/ethernet/mscc/ocelot_board.c
index 2da8eee27e98..b38820849faa 100644
--- a/drivers/net/ethernet/mscc/ocelot_board.c
+++ b/drivers/net/ethernet/mscc/ocelot_board.c
@@ -402,9 +402,9 @@ static int mscc_ocelot_probe(struct platform_device *pdev)
 
 		of_get_phy_mode(portnp, &phy_mode);
 
-		priv->phy_mode = phy_mode;
+		ocelot_port->phy_mode = phy_mode;
 
-		switch (priv->phy_mode) {
+		switch (ocelot_port->phy_mode) {
 		case PHY_INTERFACE_MODE_NA:
 			continue;
 		case PHY_INTERFACE_MODE_SGMII:
diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 1edca9725370..af914a8842bd 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -281,6 +281,7 @@ static int phylink_parse_mode(struct phylink *pl, struct fwnode_handle *fwnode)
 
 		switch (pl->link_config.interface) {
 		case PHY_INTERFACE_MODE_SGMII:
+		case PHY_INTERFACE_MODE_QSGMII:
 			phylink_set(pl->supported, 10baseT_Half);
 			phylink_set(pl->supported, 10baseT_Full);
 			phylink_set(pl->supported, 100baseT_Half);
@@ -1021,7 +1022,8 @@ void phylink_start(struct phylink *pl)
 		if (irq <= 0)
 			mod_timer(&pl->link_poll, jiffies + HZ);
 	}
-	if (pl->cfg_link_an_mode == MLO_AN_FIXED && pl->get_fixed_state)
+	if ((pl->cfg_link_an_mode == MLO_AN_FIXED && pl->get_fixed_state) ||
+	    pl->config->pcs_poll)
 		mod_timer(&pl->link_poll, jiffies + HZ);
 	if (pl->phydev)
 		phy_start(pl->phydev);
diff --git a/include/linux/fsl/enetc_mdio.h b/include/linux/fsl/enetc_mdio.h
new file mode 100644
index 000000000000..4875dd38af7e
--- /dev/null
+++ b/include/linux/fsl/enetc_mdio.h
@@ -0,0 +1,55 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
+/* Copyright 2019 NXP */
+
+#ifndef _FSL_ENETC_MDIO_H_
+#define _FSL_ENETC_MDIO_H_
+
+#include <linux/phy.h>
+
+/* PCS registers */
+#define ENETC_PCS_LINK_TIMER1			0x12
+#define ENETC_PCS_LINK_TIMER1_VAL		0x06a0
+#define ENETC_PCS_LINK_TIMER2			0x13
+#define ENETC_PCS_LINK_TIMER2_VAL		0x0003
+#define ENETC_PCS_IF_MODE			0x14
+#define ENETC_PCS_IF_MODE_SGMII_EN		BIT(0)
+#define ENETC_PCS_IF_MODE_USE_SGMII_AN		BIT(1)
+#define ENETC_PCS_IF_MODE_SGMII_SPEED(x)	(((x) << 2) & GENMASK(3, 2))
+
+/* Not a mistake, the SerDes PLL needs to be set at 3.125 GHz by Reset
+ * Configuration Word (RCW, outside Linux control) for 2.5G SGMII mode. The PCS
+ * still thinks it's at gigabit.
+ */
+enum enetc_pcs_speed {
+	ENETC_PCS_SPEED_10	= 0,
+	ENETC_PCS_SPEED_100	= 1,
+	ENETC_PCS_SPEED_1000	= 2,
+	ENETC_PCS_SPEED_2500	= 2,
+};
+
+struct enetc_hw;
+
+struct enetc_mdio_priv {
+	struct enetc_hw *hw;
+	int mdio_base;
+};
+
+#if IS_REACHABLE(CONFIG_FSL_ENETC_MDIO)
+
+int enetc_mdio_read(struct mii_bus *bus, int phy_id, int regnum);
+int enetc_mdio_write(struct mii_bus *bus, int phy_id, int regnum, u16 value);
+struct enetc_hw *enetc_hw_alloc(struct device *dev, void __iomem *port_regs);
+
+#else
+
+static inline int enetc_mdio_read(struct mii_bus *bus, int phy_id, int regnum)
+{ return -EINVAL; }
+static inline int enetc_mdio_write(struct mii_bus *bus, int phy_id, int regnum,
+				   u16 value)
+{ return -EINVAL; }
+struct enetc_hw *enetc_hw_alloc(struct device *dev, void __iomem *port_regs)
+{ return ERR_PTR(-EINVAL); }
+
+#endif
+
+#endif
diff --git a/include/linux/mii.h b/include/linux/mii.h
index 4ce8901a1af6..18c6208f56fc 100644
--- a/include/linux/mii.h
+++ b/include/linux/mii.h
@@ -372,6 +372,56 @@ static inline u32 mii_lpa_to_ethtool_lpa_x(u32 lpa)
 	return result | mii_adv_to_ethtool_adv_x(lpa);
 }
 
+/**
+ * mii_lpa_mod_linkmode_adv_sgmii
+ * @lp_advertising: pointer to destination link mode.
+ * @lpa: value of the MII_LPA register
+ *
+ * A small helper function that translates MII_LPA bits to
+ * linkmode advertisement settings for SGMII.
+ * Leaves other bits unchanged.
+ */
+static inline void
+mii_lpa_mod_linkmode_lpa_sgmii(unsigned long *lp_advertising, u32 lpa)
+{
+	u32 speed_duplex = lpa & LPA_SGMII_DPX_SPD_MASK;
+
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_1000baseT_Half_BIT, lp_advertising,
+			 speed_duplex == LPA_SGMII_1000HALF);
+
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT, lp_advertising,
+			 speed_duplex == LPA_SGMII_1000FULL);
+
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_100baseT_Half_BIT, lp_advertising,
+			 speed_duplex == LPA_SGMII_100HALF);
+
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT, lp_advertising,
+			 speed_duplex == LPA_SGMII_100FULL);
+
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_10baseT_Half_BIT, lp_advertising,
+			 speed_duplex == LPA_SGMII_10HALF);
+
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT, lp_advertising,
+			 speed_duplex == LPA_SGMII_10FULL);
+}
+
+/**
+ * mii_lpa_to_linkmode_adv_sgmii
+ * @advertising: pointer to destination link mode.
+ * @lpa: value of the MII_LPA register
+ *
+ * A small helper function that translates MII_ADVERTISE bits
+ * to linkmode advertisement settings when in SGMII mode.
+ * Clears the old value of advertising.
+ */
+static inline void mii_lpa_to_linkmode_lpa_sgmii(unsigned long *lp_advertising,
+						 u32 lpa)
+{
+	linkmode_zero(lp_advertising);
+
+	mii_lpa_mod_linkmode_lpa_sgmii(lp_advertising, lpa);
+}
+
 /**
  * mii_adv_mod_linkmode_adv_t
  * @advertising:pointer to destination link mode.
diff --git a/include/linux/phylink.h b/include/linux/phylink.h
index fed5488e3c75..523209e70947 100644
--- a/include/linux/phylink.h
+++ b/include/linux/phylink.h
@@ -63,10 +63,12 @@ enum phylink_op_type {
  * struct phylink_config - PHYLINK configuration structure
  * @dev: a pointer to a struct device associated with the MAC
  * @type: operation type of PHYLINK instance
+ * @pcs_poll: MAC PCS cannot provide link change interrupt
  */
 struct phylink_config {
 	struct device *dev;
 	enum phylink_op_type type;
+	bool pcs_poll;
 };
 
 /**
diff --git a/include/net/dsa.h b/include/net/dsa.h
index 23b1c58656d4..0c39fed8cd99 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -279,6 +279,11 @@ struct dsa_switch {
 	 */
 	bool			vlan_filtering;
 
+	/* MAC PCS does not provide link state change interrupt, and requires
+	 * polling. Flag passed on to PHYLINK.
+	 */
+	bool			pcs_poll;
+
 	size_t num_ports;
 };
 
diff --git a/include/soc/mscc/ocelot.h b/include/soc/mscc/ocelot.h
index 64cbbbe74a36..068f96b1a83e 100644
--- a/include/soc/mscc/ocelot.h
+++ b/include/soc/mscc/ocelot.h
@@ -420,6 +420,8 @@ struct ocelot_port {
 	u8				ptp_cmd;
 	struct sk_buff_head		tx_skbs;
 	u8				ts_id;
+
+	phy_interface_t			phy_mode;
 };
 
 struct ocelot {
diff --git a/drivers/net/ethernet/mscc/ocelot_ana.h b/include/soc/mscc/ocelot_ana.h
similarity index 100%
rename from drivers/net/ethernet/mscc/ocelot_ana.h
rename to include/soc/mscc/ocelot_ana.h
diff --git a/drivers/net/ethernet/mscc/ocelot_dev.h b/include/soc/mscc/ocelot_dev.h
similarity index 100%
rename from drivers/net/ethernet/mscc/ocelot_dev.h
rename to include/soc/mscc/ocelot_dev.h
diff --git a/drivers/net/ethernet/mscc/ocelot_qsys.h b/include/soc/mscc/ocelot_qsys.h
similarity index 100%
rename from drivers/net/ethernet/mscc/ocelot_qsys.h
rename to include/soc/mscc/ocelot_qsys.h
diff --git a/include/uapi/linux/mii.h b/include/uapi/linux/mii.h
index 51b48e4be1f2..0b9c3beda345 100644
--- a/include/uapi/linux/mii.h
+++ b/include/uapi/linux/mii.h
@@ -131,6 +131,18 @@
 #define NWAYTEST_LOOPBACK	0x0100	/* Enable loopback for N-way   */
 #define NWAYTEST_RESV2		0xfe00	/* Unused...                   */
 
+/* MAC and PHY tx_config_Reg[15:0] for SGMII in-band auto-negotiation.*/
+#define ADVERTISE_SGMII		0x0001	/* MAC can do SGMII            */
+#define LPA_SGMII		0x0001	/* PHY can do SGMII            */
+#define LPA_SGMII_DPX_SPD_MASK	0x1C00	/* SGMII duplex and speed bits */
+#define LPA_SGMII_10HALF	0x0000	/* Can do 10mbps half-duplex   */
+#define LPA_SGMII_10FULL	0x1000	/* Can do 10mbps full-duplex   */
+#define LPA_SGMII_100HALF	0x0400	/* Can do 100mbps half-duplex  */
+#define LPA_SGMII_100FULL	0x1400	/* Can do 100mbps full-duplex  */
+#define LPA_SGMII_1000HALF	0x0800	/* Can do 1000mbps half-duplex */
+#define LPA_SGMII_1000FULL	0x1800	/* Can do 1000mbps full-duplex */
+#define LPA_SGMII_LINK		0x8000	/* PHY link with copper-side partner */
+
 /* 1000BASE-T Control register */
 #define ADVERTISE_1000FULL	0x0200  /* Advertise 1000BASE-T full duplex */
 #define ADVERTISE_1000HALF	0x0100  /* Advertise 1000BASE-T half duplex */
diff --git a/net/dsa/port.c b/net/dsa/port.c
index ffb5601f7ed6..774facb8d547 100644
--- a/net/dsa/port.c
+++ b/net/dsa/port.c
@@ -599,6 +599,7 @@ static int dsa_port_phylink_register(struct dsa_port *dp)
 
 	dp->pl_config.dev = ds->dev;
 	dp->pl_config.type = PHYLINK_DEV;
+	dp->pl_config.pcs_poll = ds->pcs_poll;
 
 	dp->pl = phylink_create(&dp->pl_config, of_fwnode_handle(port_dn),
 				mode, &dsa_port_phylink_mac_ops);