spi: at91-usart: Add driver for at91-usart as SPI
This is the driver for at91-usart in spi mode. The USART IP can be configured to work in many modes and one of them is SPI. The driver was tested on sama5d3-xplained and sama5d4-xplained boards with enc28j60 ethernet controller as slave. Signed-off-by: Radu Pirea <radu.pirea@microchip.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviwed-by: Mark Brown <broonie@kernel.org> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
This commit is contained in:
Radu Pirea
Lee Jones
parent
937c0a26ac
commit
e1892546ff
@ -83,6 +83,14 @@ config SPI_ATMEL
|
||||
This selects a driver for the Atmel SPI Controller, present on
|
||||
many AT91 ARM chips.
|
||||
|
||||
config SPI_AT91_USART
|
||||
tristate "Atmel USART Controller SPI driver"
|
||||
depends on (ARCH_AT91 || COMPILE_TEST)
|
||||
depends on MFD_AT91_USART
|
||||
help
|
||||
This selects a driver for the AT91 USART Controller as SPI Master,
|
||||
present on AT91 and SAMA5 SoC series.
|
||||
|
||||
config SPI_AU1550
|
||||
tristate "Au1550/Au1200/Au1300 SPI Controller"
|
||||
depends on MIPS_ALCHEMY
|
||||
|
||||
@ -16,6 +16,7 @@ obj-$(CONFIG_SPI_LOOPBACK_TEST) += spi-loopback-test.o
|
||||
obj-$(CONFIG_SPI_ALTERA) += spi-altera.o
|
||||
obj-$(CONFIG_SPI_ARMADA_3700) += spi-armada-3700.o
|
||||
obj-$(CONFIG_SPI_ATMEL) += spi-atmel.o
|
||||
obj-$(CONFIG_SPI_AT91_USART) += spi-at91-usart.o
|
||||
obj-$(CONFIG_SPI_ATH79) += spi-ath79.o
|
||||
obj-$(CONFIG_SPI_AU1550) += spi-au1550.o
|
||||
obj-$(CONFIG_SPI_AXI_SPI_ENGINE) += spi-axi-spi-engine.o
|
||||
|
||||
432
drivers/spi/spi-at91-usart.c
Normal file
432
drivers/spi/spi-at91-usart.c
Normal file
@ -0,0 +1,432 @@
|
||||
// SPDX-License-Identifier: GPL-2.0
|
||||
//
|
||||
// Driver for AT91 USART Controllers as SPI
|
||||
//
|
||||
// Copyright (C) 2018 Microchip Technology Inc.
|
||||
//
|
||||
// Author: Radu Pirea <radu.pirea@microchip.com>
|
||||
|
||||
#include <linux/clk.h>
|
||||
#include <linux/delay.h>
|
||||
#include <linux/interrupt.h>
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/of_gpio.h>
|
||||
#include <linux/platform_device.h>
|
||||
|
||||
#include <linux/spi/spi.h>
|
||||
|
||||
#define US_CR 0x00
|
||||
#define US_MR 0x04
|
||||
#define US_IER 0x08
|
||||
#define US_IDR 0x0C
|
||||
#define US_CSR 0x14
|
||||
#define US_RHR 0x18
|
||||
#define US_THR 0x1C
|
||||
#define US_BRGR 0x20
|
||||
#define US_VERSION 0xFC
|
||||
|
||||
#define US_CR_RSTRX BIT(2)
|
||||
#define US_CR_RSTTX BIT(3)
|
||||
#define US_CR_RXEN BIT(4)
|
||||
#define US_CR_RXDIS BIT(5)
|
||||
#define US_CR_TXEN BIT(6)
|
||||
#define US_CR_TXDIS BIT(7)
|
||||
|
||||
#define US_MR_SPI_MASTER 0x0E
|
||||
#define US_MR_CHRL GENMASK(7, 6)
|
||||
#define US_MR_CPHA BIT(8)
|
||||
#define US_MR_CPOL BIT(16)
|
||||
#define US_MR_CLKO BIT(18)
|
||||
#define US_MR_WRDBT BIT(20)
|
||||
#define US_MR_LOOP BIT(15)
|
||||
|
||||
#define US_IR_RXRDY BIT(0)
|
||||
#define US_IR_TXRDY BIT(1)
|
||||
#define US_IR_OVRE BIT(5)
|
||||
|
||||
#define US_BRGR_SIZE BIT(16)
|
||||
|
||||
#define US_MIN_CLK_DIV 0x06
|
||||
#define US_MAX_CLK_DIV BIT(16)
|
||||
|
||||
#define US_RESET (US_CR_RSTRX | US_CR_RSTTX)
|
||||
#define US_DISABLE (US_CR_RXDIS | US_CR_TXDIS)
|
||||
#define US_ENABLE (US_CR_RXEN | US_CR_TXEN)
|
||||
#define US_OVRE_RXRDY_IRQS (US_IR_OVRE | US_IR_RXRDY)
|
||||
|
||||
#define US_INIT \
|
||||
(US_MR_SPI_MASTER | US_MR_CHRL | US_MR_CLKO | US_MR_WRDBT)
|
||||
|
||||
/* Register access macros */
|
||||
#define at91_usart_spi_readl(port, reg) \
|
||||
readl_relaxed((port)->regs + US_##reg)
|
||||
#define at91_usart_spi_writel(port, reg, value) \
|
||||
writel_relaxed((value), (port)->regs + US_##reg)
|
||||
|
||||
#define at91_usart_spi_readb(port, reg) \
|
||||
readb_relaxed((port)->regs + US_##reg)
|
||||
#define at91_usart_spi_writeb(port, reg, value) \
|
||||
writeb_relaxed((value), (port)->regs + US_##reg)
|
||||
|
||||
struct at91_usart_spi {
|
||||
struct spi_transfer *current_transfer;
|
||||
void __iomem *regs;
|
||||
struct device *dev;
|
||||
struct clk *clk;
|
||||
|
||||
/*used in interrupt to protect data reading*/
|
||||
spinlock_t lock;
|
||||
|
||||
int irq;
|
||||
unsigned int current_tx_remaining_bytes;
|
||||
unsigned int current_rx_remaining_bytes;
|
||||
|
||||
u32 spi_clk;
|
||||
u32 status;
|
||||
|
||||
bool xfer_failed;
|
||||
};
|
||||
|
||||
static inline u32 at91_usart_spi_tx_ready(struct at91_usart_spi *aus)
|
||||
{
|
||||
return aus->status & US_IR_TXRDY;
|
||||
}
|
||||
|
||||
static inline u32 at91_usart_spi_rx_ready(struct at91_usart_spi *aus)
|
||||
{
|
||||
return aus->status & US_IR_RXRDY;
|
||||
}
|
||||
|
||||
static inline u32 at91_usart_spi_check_overrun(struct at91_usart_spi *aus)
|
||||
{
|
||||
return aus->status & US_IR_OVRE;
|
||||
}
|
||||
|
||||
static inline u32 at91_usart_spi_read_status(struct at91_usart_spi *aus)
|
||||
{
|
||||
aus->status = at91_usart_spi_readl(aus, CSR);
|
||||
return aus->status;
|
||||
}
|
||||
|
||||
static inline void at91_usart_spi_tx(struct at91_usart_spi *aus)
|
||||
{
|
||||
unsigned int len = aus->current_transfer->len;
|
||||
unsigned int remaining = aus->current_tx_remaining_bytes;
|
||||
const u8 *tx_buf = aus->current_transfer->tx_buf;
|
||||
|
||||
if (!remaining)
|
||||
return;
|
||||
|
||||
if (at91_usart_spi_tx_ready(aus)) {
|
||||
at91_usart_spi_writeb(aus, THR, tx_buf[len - remaining]);
|
||||
aus->current_tx_remaining_bytes--;
|
||||
}
|
||||
}
|
||||
|
||||
static inline void at91_usart_spi_rx(struct at91_usart_spi *aus)
|
||||
{
|
||||
int len = aus->current_transfer->len;
|
||||
int remaining = aus->current_rx_remaining_bytes;
|
||||
u8 *rx_buf = aus->current_transfer->rx_buf;
|
||||
|
||||
if (!remaining)
|
||||
return;
|
||||
|
||||
rx_buf[len - remaining] = at91_usart_spi_readb(aus, RHR);
|
||||
aus->current_rx_remaining_bytes--;
|
||||
}
|
||||
|
||||
static inline void
|
||||
at91_usart_spi_set_xfer_speed(struct at91_usart_spi *aus,
|
||||
struct spi_transfer *xfer)
|
||||
{
|
||||
at91_usart_spi_writel(aus, BRGR,
|
||||
DIV_ROUND_UP(aus->spi_clk, xfer->speed_hz));
|
||||
}
|
||||
|
||||
static irqreturn_t at91_usart_spi_interrupt(int irq, void *dev_id)
|
||||
{
|
||||
struct spi_controller *controller = dev_id;
|
||||
struct at91_usart_spi *aus = spi_master_get_devdata(controller);
|
||||
|
||||
spin_lock(&aus->lock);
|
||||
at91_usart_spi_read_status(aus);
|
||||
|
||||
if (at91_usart_spi_check_overrun(aus)) {
|
||||
aus->xfer_failed = true;
|
||||
at91_usart_spi_writel(aus, IDR, US_IR_OVRE | US_IR_RXRDY);
|
||||
spin_unlock(&aus->lock);
|
||||
return IRQ_HANDLED;
|
||||
}
|
||||
|
||||
if (at91_usart_spi_rx_ready(aus)) {
|
||||
at91_usart_spi_rx(aus);
|
||||
spin_unlock(&aus->lock);
|
||||
return IRQ_HANDLED;
|
||||
}
|
||||
|
||||
spin_unlock(&aus->lock);
|
||||
|
||||
return IRQ_NONE;
|
||||
}
|
||||
|
||||
static int at91_usart_spi_setup(struct spi_device *spi)
|
||||
{
|
||||
struct at91_usart_spi *aus = spi_master_get_devdata(spi->controller);
|
||||
u32 *ausd = spi->controller_state;
|
||||
unsigned int mr = at91_usart_spi_readl(aus, MR);
|
||||
u8 bits = spi->bits_per_word;
|
||||
|
||||
if (bits != 8) {
|
||||
dev_dbg(&spi->dev, "Only 8 bits per word are supported\n");
|
||||
return -EINVAL;
|
||||
}
|
||||
|
||||
if (spi->mode & SPI_CPOL)
|
||||
mr |= US_MR_CPOL;
|
||||
else
|
||||
mr &= ~US_MR_CPOL;
|
||||
|
||||
if (spi->mode & SPI_CPHA)
|
||||
mr |= US_MR_CPHA;
|
||||
else
|
||||
mr &= ~US_MR_CPHA;
|
||||
|
||||
if (spi->mode & SPI_LOOP)
|
||||
mr |= US_MR_LOOP;
|
||||
else
|
||||
mr &= ~US_MR_LOOP;
|
||||
|
||||
if (!ausd) {
|
||||
ausd = kzalloc(sizeof(*ausd), GFP_KERNEL);
|
||||
if (!ausd)
|
||||
return -ENOMEM;
|
||||
|
||||
spi->controller_state = ausd;
|
||||
}
|
||||
|
||||
*ausd = mr;
|
||||
|
||||
dev_dbg(&spi->dev,
|
||||
"setup: bpw %u mode 0x%x -> mr %d %08x\n",
|
||||
bits, spi->mode, spi->chip_select, mr);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int at91_usart_spi_transfer_one(struct spi_controller *ctlr,
|
||||
struct spi_device *spi,
|
||||
struct spi_transfer *xfer)
|
||||
{
|
||||
struct at91_usart_spi *aus = spi_master_get_devdata(ctlr);
|
||||
|
||||
at91_usart_spi_set_xfer_speed(aus, xfer);
|
||||
aus->xfer_failed = false;
|
||||
aus->current_transfer = xfer;
|
||||
aus->current_tx_remaining_bytes = xfer->len;
|
||||
aus->current_rx_remaining_bytes = xfer->len;
|
||||
|
||||
while ((aus->current_tx_remaining_bytes ||
|
||||
aus->current_rx_remaining_bytes) && !aus->xfer_failed) {
|
||||
at91_usart_spi_read_status(aus);
|
||||
at91_usart_spi_tx(aus);
|
||||
cpu_relax();
|
||||
}
|
||||
|
||||
if (aus->xfer_failed) {
|
||||
dev_err(aus->dev, "Overrun!\n");
|
||||
return -EIO;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int at91_usart_spi_prepare_message(struct spi_controller *ctlr,
|
||||
struct spi_message *message)
|
||||
{
|
||||
struct at91_usart_spi *aus = spi_master_get_devdata(ctlr);
|
||||
struct spi_device *spi = message->spi;
|
||||
u32 *ausd = spi->controller_state;
|
||||
|
||||
at91_usart_spi_writel(aus, CR, US_ENABLE);
|
||||
at91_usart_spi_writel(aus, IER, US_OVRE_RXRDY_IRQS);
|
||||
at91_usart_spi_writel(aus, MR, *ausd);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int at91_usart_spi_unprepare_message(struct spi_controller *ctlr,
|
||||
struct spi_message *message)
|
||||
{
|
||||
struct at91_usart_spi *aus = spi_master_get_devdata(ctlr);
|
||||
|
||||
at91_usart_spi_writel(aus, CR, US_RESET | US_DISABLE);
|
||||
at91_usart_spi_writel(aus, IDR, US_OVRE_RXRDY_IRQS);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static void at91_usart_spi_cleanup(struct spi_device *spi)
|
||||
{
|
||||
struct at91_usart_spi_device *ausd = spi->controller_state;
|
||||
|
||||
spi->controller_state = NULL;
|
||||
kfree(ausd);
|
||||
}
|
||||
|
||||
static void at91_usart_spi_init(struct at91_usart_spi *aus)
|
||||
{
|
||||
at91_usart_spi_writel(aus, MR, US_INIT);
|
||||
at91_usart_spi_writel(aus, CR, US_RESET | US_DISABLE);
|
||||
}
|
||||
|
||||
static int at91_usart_gpio_setup(struct platform_device *pdev)
|
||||
{
|
||||
struct device_node *np = pdev->dev.parent->of_node;
|
||||
int i;
|
||||
int ret;
|
||||
int nb;
|
||||
|
||||
if (!np)
|
||||
return -EINVAL;
|
||||
|
||||
nb = of_gpio_named_count(np, "cs-gpios");
|
||||
for (i = 0; i < nb; i++) {
|
||||
int cs_gpio = of_get_named_gpio(np, "cs-gpios", i);
|
||||
|
||||
if (cs_gpio < 0)
|
||||
return cs_gpio;
|
||||
|
||||
if (gpio_is_valid(cs_gpio)) {
|
||||
ret = devm_gpio_request_one(&pdev->dev, cs_gpio,
|
||||
GPIOF_DIR_OUT,
|
||||
dev_name(&pdev->dev));
|
||||
if (ret)
|
||||
return ret;
|
||||
}
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int at91_usart_spi_probe(struct platform_device *pdev)
|
||||
{
|
||||
struct resource *regs;
|
||||
struct spi_controller *controller;
|
||||
struct at91_usart_spi *aus;
|
||||
struct clk *clk;
|
||||
int irq;
|
||||
int ret;
|
||||
|
||||
regs = platform_get_resource(to_platform_device(pdev->dev.parent),
|
||||
IORESOURCE_MEM, 0);
|
||||
if (!regs)
|
||||
return -EINVAL;
|
||||
|
||||
irq = platform_get_irq(to_platform_device(pdev->dev.parent), 0);
|
||||
if (irq < 0)
|
||||
return irq;
|
||||
|
||||
clk = devm_clk_get(pdev->dev.parent, "usart");
|
||||
if (IS_ERR(clk))
|
||||
return PTR_ERR(clk);
|
||||
|
||||
ret = -ENOMEM;
|
||||
controller = spi_alloc_master(&pdev->dev, sizeof(*aus));
|
||||
if (!controller)
|
||||
goto at91_usart_spi_probe_fail;
|
||||
|
||||
ret = at91_usart_gpio_setup(pdev);
|
||||
if (ret)
|
||||
goto at91_usart_spi_probe_fail;
|
||||
|
||||
controller->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LOOP | SPI_CS_HIGH;
|
||||
controller->dev.of_node = pdev->dev.parent->of_node;
|
||||
controller->bits_per_word_mask = SPI_BPW_MASK(8);
|
||||
controller->setup = at91_usart_spi_setup;
|
||||
controller->flags = SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX;
|
||||
controller->transfer_one = at91_usart_spi_transfer_one;
|
||||
controller->prepare_message = at91_usart_spi_prepare_message;
|
||||
controller->unprepare_message = at91_usart_spi_unprepare_message;
|
||||
controller->cleanup = at91_usart_spi_cleanup;
|
||||
controller->max_speed_hz = DIV_ROUND_UP(clk_get_rate(clk),
|
||||
US_MIN_CLK_DIV);
|
||||
controller->min_speed_hz = DIV_ROUND_UP(clk_get_rate(clk),
|
||||
US_MAX_CLK_DIV);
|
||||
platform_set_drvdata(pdev, controller);
|
||||
|
||||
aus = spi_master_get_devdata(controller);
|
||||
|
||||
aus->dev = &pdev->dev;
|
||||
aus->regs = devm_ioremap_resource(&pdev->dev, regs);
|
||||
if (IS_ERR(aus->regs)) {
|
||||
ret = PTR_ERR(aus->regs);
|
||||
goto at91_usart_spi_probe_fail;
|
||||
}
|
||||
|
||||
aus->irq = irq;
|
||||
aus->clk = clk;
|
||||
|
||||
ret = devm_request_irq(&pdev->dev, irq, at91_usart_spi_interrupt, 0,
|
||||
dev_name(&pdev->dev), controller);
|
||||
if (ret)
|
||||
goto at91_usart_spi_probe_fail;
|
||||
|
||||
ret = clk_prepare_enable(clk);
|
||||
if (ret)
|
||||
goto at91_usart_spi_probe_fail;
|
||||
|
||||
aus->spi_clk = clk_get_rate(clk);
|
||||
at91_usart_spi_init(aus);
|
||||
|
||||
spin_lock_init(&aus->lock);
|
||||
ret = devm_spi_register_master(&pdev->dev, controller);
|
||||
if (ret)
|
||||
goto at91_usart_fail_register_master;
|
||||
|
||||
dev_info(&pdev->dev,
|
||||
"AT91 USART SPI Controller version 0x%x at %pa (irq %d)\n",
|
||||
at91_usart_spi_readl(aus, VERSION),
|
||||
®s->start, irq);
|
||||
|
||||
return 0;
|
||||
|
||||
at91_usart_fail_register_master:
|
||||
clk_disable_unprepare(clk);
|
||||
at91_usart_spi_probe_fail:
|
||||
spi_master_put(controller);
|
||||
return ret;
|
||||
}
|
||||
|
||||
static int at91_usart_spi_remove(struct platform_device *pdev)
|
||||
{
|
||||
struct spi_controller *ctlr = platform_get_drvdata(pdev);
|
||||
struct at91_usart_spi *aus = spi_master_get_devdata(ctlr);
|
||||
|
||||
clk_disable_unprepare(aus->clk);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static const struct of_device_id at91_usart_spi_dt_ids[] = {
|
||||
{ .compatible = "microchip,at91sam9g45-usart-spi"},
|
||||
{ /* sentinel */}
|
||||
};
|
||||
|
||||
MODULE_DEVICE_TABLE(of, at91_usart_spi_dt_ids);
|
||||
|
||||
static struct platform_driver at91_usart_spi_driver = {
|
||||
.driver = {
|
||||
.name = "at91_usart_spi",
|
||||
},
|
||||
.probe = at91_usart_spi_probe,
|
||||
.remove = at91_usart_spi_remove,
|
||||
};
|
||||
|
||||
module_platform_driver(at91_usart_spi_driver);
|
||||
|
||||
MODULE_DESCRIPTION("Microchip AT91 USART SPI Controller driver");
|
||||
MODULE_AUTHOR("Radu Pirea <radu.pirea@microchip.com>");
|
||||
MODULE_LICENSE("GPL v2");
|
||||
MODULE_ALIAS("platform:at91_usart_spi");
|
||||
Loading…
Reference in New Issue
Block a user