iv/linux
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity

thermal: imx: add i.MX7 thermal sensor support

Browse Source 
This patch adds i.MX7 thermal sensor support, most
of the i.MX7 thermal sensor functions are same with
i.MX6 except the registers offset/layout, so we move
those registers offset/layout definitions to soc data
structure.

i.MX7 uses single calibration data @25C, the calibration
data is located at OCOTP offset 0x4F0, bit[17:9], the
formula is as below:

Tmeas = (Nmeas - n1) + 25; n1 is the fuse value for 25C.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This commit is contained in:
Anson Huang 2018-03-02 09:59:30 +08:00 committed by Eduardo Valentin
parent 3966be3c08
commit f085f672b7
2 changed files with 237 additions and 63 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

9
Documentation/devicetree/bindings/thermal/imx-thermal.txt
View File

@ -1,8 +1,13 @@
* Temperature Monitor (TEMPMON) on Freescale i.MX SoCs
Required properties:
- compatible : "fsl,imx6q-tempmon" for i.MX6Q, "fsl,imx6sx-tempmon" for i.MX6SX.
i.MX6SX has two more IRQs than i.MX6Q, one is IRQ_LOW and the other is IRQ_PANIC,
- compatible : must be one of following:
- "fsl,imx6q-tempmon" for i.MX6Q,
- "fsl,imx6sx-tempmon" for i.MX6SX,
- "fsl,imx7d-tempmon" for i.MX7S/D.
- interrupts : the interrupt output of the controller:
i.MX6Q has one IRQ which will be triggered when temperature is higher than high threshold,
i.MX6SX and i.MX7S/D have two more IRQs than i.MX6Q, one is IRQ_LOW and the other is IRQ_PANIC,
when temperature is below than low threshold, IRQ_LOW will be triggered, when temperature
is higher than panic threshold, system will auto reboot by SRC module.
- fsl,tempmon : phandle pointer to system controller that contains TEMPMON

291
drivers/thermal/imx_thermal.c
View File

@ -31,35 +31,57 @@
#define REG_CLR 0x8
#define REG_TOG 0xc
#define MISC0 0x0150
#define MISC0_REFTOP_SELBIASOFF (1 << 3)
#define MISC1 0x0160
#define MISC1_IRQ_TEMPHIGH (1 << 29)
/* i.MX6 specific */
#define IMX6_MISC0 0x0150
#define IMX6_MISC0_REFTOP_SELBIASOFF (1 << 3)
#define IMX6_MISC1 0x0160
#define IMX6_MISC1_IRQ_TEMPHIGH (1 << 29)
/* Below LOW and PANIC bits are only for TEMPMON_IMX6SX */
#define MISC1_IRQ_TEMPLOW (1 << 28)
#define MISC1_IRQ_TEMPPANIC (1 << 27)
#define IMX6_MISC1_IRQ_TEMPLOW (1 << 28)
#define IMX6_MISC1_IRQ_TEMPPANIC (1 << 27)
#define TEMPSENSE0 0x0180
#define TEMPSENSE0_ALARM_VALUE_SHIFT 20
#define TEMPSENSE0_ALARM_VALUE_MASK (0xfff << TEMPSENSE0_ALARM_VALUE_SHIFT)
#define TEMPSENSE0_TEMP_CNT_SHIFT 8
#define TEMPSENSE0_TEMP_CNT_MASK (0xfff << TEMPSENSE0_TEMP_CNT_SHIFT)
#define TEMPSENSE0_FINISHED (1 << 2)
#define TEMPSENSE0_MEASURE_TEMP (1 << 1)
#define TEMPSENSE0_POWER_DOWN (1 << 0)
#define IMX6_TEMPSENSE0 0x0180
#define IMX6_TEMPSENSE0_ALARM_VALUE_SHIFT 20
#define IMX6_TEMPSENSE0_ALARM_VALUE_MASK (0xfff << 20)
#define IMX6_TEMPSENSE0_TEMP_CNT_SHIFT 8
#define IMX6_TEMPSENSE0_TEMP_CNT_MASK (0xfff << 8)
#define IMX6_TEMPSENSE0_FINISHED (1 << 2)
#define IMX6_TEMPSENSE0_MEASURE_TEMP (1 << 1)
#define IMX6_TEMPSENSE0_POWER_DOWN (1 << 0)
#define TEMPSENSE1 0x0190
#define TEMPSENSE1_MEASURE_FREQ 0xffff
/* Below TEMPSENSE2 is only for TEMPMON_IMX6SX */
#define TEMPSENSE2 0x0290
#define TEMPSENSE2_LOW_VALUE_SHIFT 0
#define TEMPSENSE2_LOW_VALUE_MASK 0xfff
#define TEMPSENSE2_PANIC_VALUE_SHIFT 16
#define TEMPSENSE2_PANIC_VALUE_MASK 0xfff0000
#define IMX6_TEMPSENSE1 0x0190
#define IMX6_TEMPSENSE1_MEASURE_FREQ 0xffff
#define IMX6_TEMPSENSE1_MEASURE_FREQ_SHIFT 0
#define OCOTP_MEM0 0x0480
#define OCOTP_ANA1 0x04e0
/* Below TEMPSENSE2 is only for TEMPMON_IMX6SX */
#define IMX6_TEMPSENSE2 0x0290
#define IMX6_TEMPSENSE2_LOW_VALUE_SHIFT 0
#define IMX6_TEMPSENSE2_LOW_VALUE_MASK 0xfff
#define IMX6_TEMPSENSE2_PANIC_VALUE_SHIFT 16
#define IMX6_TEMPSENSE2_PANIC_VALUE_MASK 0xfff0000
/* i.MX7 specific */
#define IMX7_ANADIG_DIGPROG 0x800
#define IMX7_TEMPSENSE0 0x300
#define IMX7_TEMPSENSE0_PANIC_ALARM_SHIFT 18
#define IMX7_TEMPSENSE0_PANIC_ALARM_MASK (0x1ff << 18)
#define IMX7_TEMPSENSE0_HIGH_ALARM_SHIFT 9
#define IMX7_TEMPSENSE0_HIGH_ALARM_MASK (0x1ff << 9)
#define IMX7_TEMPSENSE0_LOW_ALARM_SHIFT 0
#define IMX7_TEMPSENSE0_LOW_ALARM_MASK 0x1ff
#define IMX7_TEMPSENSE1 0x310
#define IMX7_TEMPSENSE1_MEASURE_FREQ_SHIFT 16
#define IMX7_TEMPSENSE1_MEASURE_FREQ_MASK (0xffff << 16)
#define IMX7_TEMPSENSE1_FINISHED (1 << 11)
#define IMX7_TEMPSENSE1_MEASURE_TEMP (1 << 10)
#define IMX7_TEMPSENSE1_POWER_DOWN (1 << 9)
#define IMX7_TEMPSENSE1_TEMP_VALUE_SHIFT 0
#define IMX7_TEMPSENSE1_TEMP_VALUE_MASK 0x1ff
/* The driver supports 1 passive trip point and 1 critical trip point */
enum imx_thermal_trip {
IMX_TRIP_PASSIVE,
@ -72,17 +94,114 @@ enum imx_thermal_trip {
#define TEMPMON_IMX6Q 1
#define TEMPMON_IMX6SX 2
#define TEMPMON_IMX7D 3
struct thermal_soc_data {
u32 version;
u32 sensor_ctrl;
u32 power_down_mask;
u32 measure_temp_mask;
u32 measure_freq_ctrl;
u32 measure_freq_mask;
u32 measure_freq_shift;
u32 temp_data;
u32 temp_value_mask;
u32 temp_value_shift;
u32 temp_valid_mask;
u32 panic_alarm_ctrl;
u32 panic_alarm_mask;
u32 panic_alarm_shift;
u32 high_alarm_ctrl;
u32 high_alarm_mask;
u32 high_alarm_shift;
u32 low_alarm_ctrl;
u32 low_alarm_mask;
u32 low_alarm_shift;
};
static struct thermal_soc_data thermal_imx6q_data = {
.version = TEMPMON_IMX6Q,
.sensor_ctrl = IMX6_TEMPSENSE0,
.power_down_mask = IMX6_TEMPSENSE0_POWER_DOWN,
.measure_temp_mask = IMX6_TEMPSENSE0_MEASURE_TEMP,
.measure_freq_ctrl = IMX6_TEMPSENSE1,
.measure_freq_shift = IMX6_TEMPSENSE1_MEASURE_FREQ_SHIFT,
.measure_freq_mask = IMX6_TEMPSENSE1_MEASURE_FREQ,
.temp_data = IMX6_TEMPSENSE0,
.temp_value_mask = IMX6_TEMPSENSE0_TEMP_CNT_MASK,
.temp_value_shift = IMX6_TEMPSENSE0_TEMP_CNT_SHIFT,
.temp_valid_mask = IMX6_TEMPSENSE0_FINISHED,
.high_alarm_ctrl = IMX6_TEMPSENSE0,
.high_alarm_mask = IMX6_TEMPSENSE0_ALARM_VALUE_MASK,
.high_alarm_shift = IMX6_TEMPSENSE0_ALARM_VALUE_SHIFT,
};
static struct thermal_soc_data thermal_imx6sx_data = {
.version = TEMPMON_IMX6SX,
.sensor_ctrl = IMX6_TEMPSENSE0,
.power_down_mask = IMX6_TEMPSENSE0_POWER_DOWN,
.measure_temp_mask = IMX6_TEMPSENSE0_MEASURE_TEMP,
.measure_freq_ctrl = IMX6_TEMPSENSE1,
.measure_freq_shift = IMX6_TEMPSENSE1_MEASURE_FREQ_SHIFT,
.measure_freq_mask = IMX6_TEMPSENSE1_MEASURE_FREQ,
.temp_data = IMX6_TEMPSENSE0,
.temp_value_mask = IMX6_TEMPSENSE0_TEMP_CNT_MASK,
.temp_value_shift = IMX6_TEMPSENSE0_TEMP_CNT_SHIFT,
.temp_valid_mask = IMX6_TEMPSENSE0_FINISHED,
.high_alarm_ctrl = IMX6_TEMPSENSE0,
.high_alarm_mask = IMX6_TEMPSENSE0_ALARM_VALUE_MASK,
.high_alarm_shift = IMX6_TEMPSENSE0_ALARM_VALUE_SHIFT,
.panic_alarm_ctrl = IMX6_TEMPSENSE2,
.panic_alarm_mask = IMX6_TEMPSENSE2_PANIC_VALUE_MASK,
.panic_alarm_shift = IMX6_TEMPSENSE2_PANIC_VALUE_SHIFT,
.low_alarm_ctrl = IMX6_TEMPSENSE2,
.low_alarm_mask = IMX6_TEMPSENSE2_LOW_VALUE_MASK,
.low_alarm_shift = IMX6_TEMPSENSE2_LOW_VALUE_SHIFT,
};
static struct thermal_soc_data thermal_imx7d_data = {
.version = TEMPMON_IMX7D,
.sensor_ctrl = IMX7_TEMPSENSE1,
.power_down_mask = IMX7_TEMPSENSE1_POWER_DOWN,
.measure_temp_mask = IMX7_TEMPSENSE1_MEASURE_TEMP,
.measure_freq_ctrl = IMX7_TEMPSENSE1,
.measure_freq_shift = IMX7_TEMPSENSE1_MEASURE_FREQ_SHIFT,
.measure_freq_mask = IMX7_TEMPSENSE1_MEASURE_FREQ_MASK,
.temp_data = IMX7_TEMPSENSE1,
.temp_value_mask = IMX7_TEMPSENSE1_TEMP_VALUE_MASK,
.temp_value_shift = IMX7_TEMPSENSE1_TEMP_VALUE_SHIFT,
.temp_valid_mask = IMX7_TEMPSENSE1_FINISHED,
.panic_alarm_ctrl = IMX7_TEMPSENSE1,
.panic_alarm_mask = IMX7_TEMPSENSE0_PANIC_ALARM_MASK,
.panic_alarm_shift = IMX7_TEMPSENSE0_PANIC_ALARM_SHIFT,
.high_alarm_ctrl = IMX7_TEMPSENSE0,
.high_alarm_mask = IMX7_TEMPSENSE0_HIGH_ALARM_MASK,
.high_alarm_shift = IMX7_TEMPSENSE0_HIGH_ALARM_SHIFT,
.low_alarm_ctrl = IMX7_TEMPSENSE0,
.low_alarm_mask = IMX7_TEMPSENSE0_LOW_ALARM_MASK,
.low_alarm_shift = IMX7_TEMPSENSE0_LOW_ALARM_SHIFT,
};
struct imx_thermal_data {
@ -107,31 +226,42 @@ struct imx_thermal_data {
static void imx_set_panic_temp(struct imx_thermal_data *data,
int panic_temp)
{
const struct thermal_soc_data *soc_data = data->socdata;
struct regmap *map = data->tempmon;
int critical_value;
critical_value = (data->c2 - panic_temp) / data->c1;
regmap_write(map, TEMPSENSE2 + REG_CLR, TEMPSENSE2_PANIC_VALUE_MASK);
regmap_write(map, TEMPSENSE2 + REG_SET, critical_value <<
TEMPSENSE2_PANIC_VALUE_SHIFT);
regmap_write(map, soc_data->panic_alarm_ctrl + REG_CLR,
soc_data->panic_alarm_mask);
regmap_write(map, soc_data->panic_alarm_ctrl + REG_SET,
critical_value << soc_data->panic_alarm_shift);
}
static void imx_set_alarm_temp(struct imx_thermal_data *data,
int alarm_temp)
{
struct regmap *map = data->tempmon;
const struct thermal_soc_data *soc_data = data->socdata;
int alarm_value;
data->alarm_temp = alarm_temp;
alarm_value = (data->c2 - alarm_temp) / data->c1;
regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_ALARM_VALUE_MASK);
regmap_write(map, TEMPSENSE0 + REG_SET, alarm_value <<
TEMPSENSE0_ALARM_VALUE_SHIFT);
if (data->socdata->version == TEMPMON_IMX7D)
alarm_value = alarm_temp / 1000 + data->c1 - 25;
else
alarm_value = (data->c2 - alarm_temp) / data->c1;
regmap_write(map, soc_data->high_alarm_ctrl + REG_CLR,
soc_data->high_alarm_mask);
regmap_write(map, soc_data->high_alarm_ctrl + REG_SET,
alarm_value << soc_data->high_alarm_shift);
}
static int imx_get_temp(struct thermal_zone_device *tz, int *temp)
{
struct imx_thermal_data *data = tz->devdata;
const struct thermal_soc_data *soc_data = data->socdata;
struct regmap *map = data->tempmon;
unsigned int n_meas;
bool wait;
@ -139,16 +269,18 @@ static int imx_get_temp(struct thermal_zone_device *tz, int *temp)
if (data->mode == THERMAL_DEVICE_ENABLED) {
/* Check if a measurement is currently in progress */
regmap_read(map, TEMPSENSE0, &val);
wait = !(val & TEMPSENSE0_FINISHED);
regmap_read(map, soc_data->temp_data, &val);
wait = !(val & soc_data->temp_valid_mask);
} else {
/*
* Every time we measure the temperature, we will power on the
* temperature sensor, enable measurements, take a reading,
* disable measurements, power off the temperature sensor.
*/
regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_POWER_DOWN);
regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_MEASURE_TEMP);
regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
soc_data->power_down_mask);
regmap_write(map, soc_data->sensor_ctrl + REG_SET,
soc_data->measure_temp_mask);
wait = true;
}
@ -160,22 +292,28 @@ static int imx_get_temp(struct thermal_zone_device *tz, int *temp)
if (wait)
usleep_range(20, 50);
regmap_read(map, TEMPSENSE0, &val);
regmap_read(map, soc_data->temp_data, &val);
if (data->mode != THERMAL_DEVICE_ENABLED) {
regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_MEASURE_TEMP);
regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_POWER_DOWN);
regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
soc_data->measure_temp_mask);
regmap_write(map, soc_data->sensor_ctrl + REG_SET,
soc_data->power_down_mask);
}
if ((val & TEMPSENSE0_FINISHED) == 0) {
if ((val & soc_data->temp_valid_mask) == 0) {
dev_dbg(&tz->device, "temp measurement never finished\n");
return -EAGAIN;
}
n_meas = (val & TEMPSENSE0_TEMP_CNT_MASK) >> TEMPSENSE0_TEMP_CNT_SHIFT;
n_meas = (val & soc_data->temp_value_mask)
>> soc_data->temp_value_shift;
/* See imx_init_calib() for formula derivation */
*temp = data->c2 - n_meas * data->c1;
if (data->socdata->version == TEMPMON_IMX7D)
*temp = (n_meas - data->c1 + 25) * 1000;
else
*temp = data->c2 - n_meas * data->c1;
/* Update alarm value to next higher trip point for TEMPMON_IMX6Q */
if (data->socdata->version == TEMPMON_IMX6Q) {
@ -219,21 +357,26 @@ static int imx_set_mode(struct thermal_zone_device *tz,
{
struct imx_thermal_data *data = tz->devdata;
struct regmap *map = data->tempmon;
const struct thermal_soc_data *soc_data = data->socdata;
if (mode == THERMAL_DEVICE_ENABLED) {
tz->polling_delay = IMX_POLLING_DELAY;
tz->passive_delay = IMX_PASSIVE_DELAY;
regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_POWER_DOWN);
regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_MEASURE_TEMP);
regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
soc_data->power_down_mask);
regmap_write(map, soc_data->sensor_ctrl + REG_SET,
soc_data->measure_temp_mask);
if (!data->irq_enabled) {
data->irq_enabled = true;
enable_irq(data->irq);
}
} else {
regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_MEASURE_TEMP);
regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_POWER_DOWN);
regmap_write(map, soc_data->sensor_ctrl + REG_CLR,
soc_data->measure_temp_mask);
regmap_write(map, soc_data->sensor_ctrl + REG_SET,
soc_data->power_down_mask);
tz->polling_delay = 0;
tz->passive_delay = 0;
@ -354,6 +497,15 @@ static int imx_init_calib(struct platform_device *pdev, u32 ocotp_ana1)
return -EINVAL;
}
/*
* On i.MX7D, we only use the calibration data at 25C to get the temp,
* Tmeas = ( Nmeas - n1) + 25; n1 is the fuse value for 25C.
*/
if (data->socdata->version == TEMPMON_IMX7D) {
data->c1 = (ocotp_ana1 >> 9) & 0x1ff;
return 0;
}
/*
* The sensor is calibrated at 25 °C (aka T1) and the value measured
* (aka N1) at this temperature is provided in bits [31:20] in the
@ -492,6 +644,7 @@ static irqreturn_t imx_thermal_alarm_irq_thread(int irq, void *dev)
static const struct of_device_id of_imx_thermal_match[] = {
{ .compatible = "fsl,imx6q-tempmon", .data = &thermal_imx6q_data, },
{ .compatible = "fsl,imx6sx-tempmon", .data = &thermal_imx6sx_data, },
{ .compatible = "fsl,imx7d-tempmon", .data = &thermal_imx7d_data, },
{ /* end */ }
};
MODULE_DEVICE_TABLE(of, of_imx_thermal_match);
@ -523,14 +676,15 @@ static int imx_thermal_probe(struct platform_device *pdev)
/* make sure the IRQ flag is clear before enabling irq on i.MX6SX */
if (data->socdata->version == TEMPMON_IMX6SX) {
regmap_write(map, MISC1 + REG_CLR, MISC1_IRQ_TEMPHIGH |
MISC1_IRQ_TEMPLOW | MISC1_IRQ_TEMPPANIC);
regmap_write(map, IMX6_MISC1 + REG_CLR,
IMX6_MISC1_IRQ_TEMPHIGH | IMX6_MISC1_IRQ_TEMPLOW
| IMX6_MISC1_IRQ_TEMPPANIC);
/*
* reset value of LOW ALARM is incorrect, set it to lowest
* value to avoid false trigger of low alarm.
*/
regmap_write(map, TEMPSENSE2 + REG_SET,
TEMPSENSE2_LOW_VALUE_MASK);
regmap_write(map, data->socdata->low_alarm_ctrl + REG_SET,
data->socdata->low_alarm_mask);
}
data->irq = platform_get_irq(pdev, 0);
@ -557,11 +711,17 @@ static int imx_thermal_probe(struct platform_device *pdev)
}
/* Make sure sensor is in known good state for measurements */
regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_POWER_DOWN);
regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_MEASURE_TEMP);
regmap_write(map, TEMPSENSE1 + REG_CLR, TEMPSENSE1_MEASURE_FREQ);
regmap_write(map, MISC0 + REG_SET, MISC0_REFTOP_SELBIASOFF);
regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_POWER_DOWN);
regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
data->socdata->power_down_mask);
regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
data->socdata->measure_temp_mask);
regmap_write(map, data->socdata->measure_freq_ctrl + REG_CLR,
data->socdata->measure_freq_mask);
if (data->socdata->version != TEMPMON_IMX7D)
regmap_write(map, IMX6_MISC0 + REG_SET,
IMX6_MISC0_REFTOP_SELBIASOFF);
regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
data->socdata->power_down_mask);
data->policy = cpufreq_cpu_get(0);
if (!data->policy) {
@ -626,16 +786,20 @@ static int imx_thermal_probe(struct platform_device *pdev)
data->temp_passive / 1000);
/* Enable measurements at ~ 10 Hz */
regmap_write(map, TEMPSENSE1 + REG_CLR, TEMPSENSE1_MEASURE_FREQ);
regmap_write(map, data->socdata->measure_freq_ctrl + REG_CLR,
data->socdata->measure_freq_mask);
measure_freq = DIV_ROUND_UP(32768, 10); /* 10 Hz */
regmap_write(map, TEMPSENSE1 + REG_SET, measure_freq);
regmap_write(map, data->socdata->measure_freq_ctrl + REG_SET,
measure_freq << data->socdata->measure_freq_shift);
imx_set_alarm_temp(data, data->temp_passive);
if (data->socdata->version == TEMPMON_IMX6SX)
imx_set_panic_temp(data, data->temp_critical);
regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_POWER_DOWN);
regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_MEASURE_TEMP);
regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
data->socdata->power_down_mask);
regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
data->socdata->measure_temp_mask);
data->irq_enabled = true;
data->mode = THERMAL_DEVICE_ENABLED;
@ -661,7 +825,8 @@ static int imx_thermal_remove(struct platform_device *pdev)
struct regmap *map = data->tempmon;
/* Disable measurements */
regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_POWER_DOWN);
regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
data->socdata->power_down_mask);
if (!IS_ERR(data->thermal_clk))
clk_disable_unprepare(data->thermal_clk);
@ -684,8 +849,10 @@ static int imx_thermal_suspend(struct device *dev)
* temperature will be read as the thermal sensor is powered
* down.
*/
regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_MEASURE_TEMP);
regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_POWER_DOWN);
regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
data->socdata->measure_temp_mask);
regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
data->socdata->power_down_mask);
data->mode = THERMAL_DEVICE_DISABLED;
clk_disable_unprepare(data->thermal_clk);
@ -702,8 +869,10 @@ static int imx_thermal_resume(struct device *dev)
if (ret)
return ret;
/* Enabled thermal sensor after resume */
regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_POWER_DOWN);
regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_MEASURE_TEMP);
regmap_write(map, data->socdata->sensor_ctrl + REG_CLR,
data->socdata->power_down_mask);
regmap_write(map, data->socdata->sensor_ctrl + REG_SET,
data->socdata->measure_temp_mask);
data->mode = THERMAL_DEVICE_ENABLED;
return 0;