IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
There is no need to compare *val.vu32* with < 0 because
such variable is of type u32 (32 bits, unsigned), making it
impossible to hold a negative value. Fix this by removing
such comparison.
Also, initialize variable *max_val* to -1, just in case
it is not initialized to either BNXT_MSIX_VEC_MAX or
BNXT_MSIX_VEC_MIN_MAX before using it in a comparison
with val.vu32 at line 159:
if (val.vu32 > max_val)
Addresses-Coverity-ID: 1473915 ("Unsigned compared against 0")
Addresses-Coverity-ID: 1473920 ("Uninitialized scalar variable")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds following driver-specific permanent mode boolean
parameter.
gre_ver_check - Generic Routing Encapsulation(GRE) version check
will be enabled in the device. If disabled, device skips version
checking for GRE packets.
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for following generic permanent mode
devlink parameters. They can be modified using devlink param
commands.
msix_vec_per_pf_max - This param sets the number of MSIX vectors
that the device requests from the host on driver initialization.
This value is set in the device which limits MSIX vectors per PF.
msix_vec_per_pf_min - This param sets the number of minimal MSIX
vectors required for the device initialization. Value 0 indicates
a default value is selected. This value is set in the device which
limits MSIX vectors per PF.
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ignore_ari generic permanent mode
devlink parameter. This parameter is disabled by default. It can be
enabled using devlink param commands.
ignore_ari - If enabled, device ignores ARI(Alternate Routing ID)
capability, even when platforms has the support and creates same number
of partitions when platform does not support ARI capability.
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following compile warning:
drivers/net/ethernet/broadcom/bnxt/bnxt_devlink.c:49:5: warning: nvm_param.dir_type may be used uninitialized in this function [-Wmaybe-uninitialized]
if (nvm_param.dir_type == BNXT_NVM_PORT_CFG)
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New interface has firmware core dump support, new extended port
statistics, and IF state change notifications to the firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create initial devlink parameters table for bnxt_en.
Table consists of a permanent generic parameter.
enable_sriov - Enables Single-Root Input/Output Virtualization(SR-IOV)
characteristic of the device.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds IPv4 vxlan encap/decap action support to TC-flower
offload.
For vxlan encap, the driver maintains a tunnel encap hash-table.
When a new flow with a tunnel encap action arrives, this table
is looked up; if an encap entry exists, it uses the already
programmed encap_record_handle as the tunnel_handle in the
hwrm_cfa_flow_alloc cmd. Else, a new encap node is added and the
L2 header fields are queried via a route lookup.
hwrm_cfa_encap_record_alloc cmd is used to create a new encap
record and the encap_record_handle is used as the tunnel_handle
while adding the flow.
For vxlan decap, the driver maintains a tunnel decap hash-table.
When a new flow with a tunnel decap action arrives, this table
is looked up; if a decap entry exists, it uses the already
programmed decap_filter_handle as the tunnel_handle in the
hwrm_cfa_flow_alloc cmd. Else, a new decap node is added and
a decap_filter_handle is alloc'd via the hwrm_cfa_decap_filter_alloc
cmd. This handle is used as the tunnel_handle while adding the flow.
The code to issue the HWRM FW cmds is introduced in a follow-up patch.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving generic devlink code (registration) out of VF-R code
into new bnxt_devlink file, in preparation for future work
to add additional devlink functionality to bnxt.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Acked-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
