IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Guangbin Huang says:
====================
net: hns3: add some fixes for -net
This series adds some fixes for the HNS3 ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 driver includes hns3.ko, hnae3.ko and hclge.ko.
hns3.ko includes network stack and pci_driver, hclge.ko includes
HW device action, algo_ops and timer task, hnae3.ko includes some
register function.
When SRIOV is enable and hclge.ko is removed, HW device is unloaded
but VF still exists, PF will not reply VF mbx messages, and cause
errors.
This patch fix it by disable SRIOV before remove hclge.ko.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The task of VF reset is performed through the workqueue. It checks the
value of hdev->reset_pending to determine whether to exit the loop.
However, the value of hdev->reset_pending may also be assigned by
the interrupt function hclgevf_misc_irq_handle(), which may cause the
loop fail to exit and keep occupying the workqueue. This loop is not
necessary, so remove it and the workqueue will be rescheduled if the
reset needs to be retried or a new reset occurs.
Fixes: 1cc9bc6e5867 ("net: hns3: split hclgevf_reset() into preparing and rebuilding part")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when there is a rx page allocation failure, it is
possible that polling may be stopped if there is no more packet
to be reveiced, which may cause queue stall problem under memory
pressure.
This patch makes sure polling is scheduled again when there is
any rx page allocation failure, and polling will try to allocate
receive buffers until it succeeds.
Now the allocation retry is added, it is unnecessary to do the rx
page allocation at the end of rx cleaning, so remove it. And reset
the unused_count to zero after calling hns3_nic_alloc_rx_buffers()
to avoid calling hns3_nic_alloc_rx_buffers() repeatedly under
memory pressure.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx unused desc is the desc that need attatching new buffer
before refilling to hw to receive new packet, the number of
desc need attatching new buffer is calculated using next_to_use
and next_to_clean. when next_to_use == next_to_clean, currently
hns3 driver assumes that all the desc has the buffer attatched,
but 'next_to_use == next_to_clean' also means all the desc need
attatching new buffer if hw has comsumed all the desc and the
driver has not attatched any buffer to the desc yet.
This patch adds 'refill' in desc_cb to indicate whether a new
buffer has been refilled to a desc.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the max tx size supported by the hw is calculated by
using the max BD num supported by the hw. According to the hw
user manual, the max tx size is fixed value for both non-TSO and
TSO skb.
This patch updates the max tx size according to the manual.
Fixes: 8ae10cfb5089("net: hns3: support tx-scatter-gather-fraglist feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ets dwrr bandwidth of tc is set to 0, the hardware will switch to SP
mode. In this case, this tc may occupy all the tx bandwidth if it has
huge traffic, so it violates the purpose of the user setting.
To fix this problem, limit the ets dwrr bandwidth must greater than 0.
Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, DWRR of tc will be initialized to a fixed value when this tc
is enabled, but it is not been reset to 0 when this tc is disabled. It
cause a problem that the DWRR of unused tc is not 0 after using tc tool
to add and delete multi-tc parameters.
For examples, after enabling 4 TCs and restoring to 1 TC by follow
tc commands:
$ tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3 0 1 2 3 queues \
8@0 8@8 8@16 8@24 hw 1 mode channel
$ tc qdisc del dev eth0 root
Now there is just one TC is enabled for eth0, but the tc info querying by
debugfs is shown as follow:
$ cat /mnt/hns3/0000:7d:00.0/tm/tc_sch_info
enabled tc number: 1
weight_offset: 14
TC MODE WEIGHT
0 dwrr 100
1 dwrr 100
2 dwrr 100
3 dwrr 100
4 dwrr 0
5 dwrr 0
6 dwrr 0
7 dwrr 0
This patch fixes it by resetting DWRR of tc to 0 when tc is disabled.
Fixes: 848440544b41 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add configuration of interrupt type and fifo interrupt enable of TM QCN
error event if enabled, otherwise this event will not be reported when
there is error.
Fixes: d914971df022 ("net: hns3: remove redundant query in hclge_config_tm_hw_err_int()")
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With PREEMPT_COUNT=y, when a CPU is offlined and then onlined again, we
get:
BUG: scheduling while atomic: swapper/1/0/0x00000000
no locks held by swapper/1/0.
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.15.0-rc2+ #100
Call Trace:
dump_stack_lvl+0xac/0x108
__schedule_bug+0xac/0xe0
__schedule+0xcf8/0x10d0
schedule_idle+0x3c/0x70
do_idle+0x2d8/0x4a0
cpu_startup_entry+0x38/0x40
start_secondary+0x2ec/0x3a0
start_secondary_prolog+0x10/0x14
This is because powerpc's arch_cpu_idle_dead() decrements the idle task's
preempt count, for reasons explained in commit a7c2bb8279d2 ("powerpc:
Re-enable preemption before cpu_die()"), specifically "start_secondary()
expects a preempt_count() of 0."
However, since commit 2c669ef6979c ("powerpc/preempt: Don't touch the idle
task's preempt_count during hotplug") and commit f1a0a376ca0c ("sched/core:
Initialize the idle task with preemption disabled"), that justification no
longer holds.
The idle task isn't supposed to re-enable preemption, so remove the
vestigial preempt_enable() from the CPU offline path.
Tested with pseries and powernv in qemu, and pseries on PowerVM.
Fixes: 2c669ef6979c ("powerpc/preempt: Don't touch the idle task's preempt_count during hotplug")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211015173902.2278118-1-nathanl@linux.ibm.com
In isa206_idle_insn_mayloss() we store various registers into the stack
red zone, which is allowed.
However inside the IDLE_STATE_ENTER_SEQ_NORET macro we save r2 again,
to 0(r1), which corrupts the stack back chain.
We used to do the same in isa206_idle_insn_mayloss() itself, but we
fixed that in 73287caa9210 ("powerpc64/idle: Fix SP offsets when saving
GPRs"), however we missed that the macro also corrupts the back chain.
Corrupting the back chain is bad for debuggability but doesn't
necessarily cause a bug.
However we recently changed the stack handling in some KVM code, and it
now relies on the stack back chain being valid when it returns. The
corruption causes that code to return with r1 pointing somewhere in
kernel data, at some point LR is restored from the stack and we branch
to NULL or somewhere else invalid.
Only affects Power8 hosts running KVM guests, with dynamic_mt_modes
enabled (which it is by default).
The fixes tag below points to the commit that changed the KVM stack
handling, exposing this bug. The actual corruption of the back chain has
always existed since 948cf67c4726 ("powerpc: Add NAP mode support on
Power7 in HV mode").
Fixes: 9b4416c5095c ("KVM: PPC: Book3S HV: Fix stack handling in idle_kvm_start_guest()")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211020094826.3222052-1-mpe@ellerman.id.au
Vladimir Oltean says:
====================
New RGMII delay DT bindings for the SJA1105 DSA driver
During recent reviews I've been telling people that new MAC drivers
should adopt a certain DT binding format for RGMII delays in order to
avoid conflicting interpretations. Some suggestions were better received
than others, and it appears we are still far from a consensus.
Part of the problem seems to be that there are still drivers that apply
RGMII delays based on an incorrect interpretation of the device tree,
and these serve as a bad example for others.
I happen to maintain one of those drivers and I am able to test it, so I
figure that one of the ways in which I can make a change is to stop
providing a bad example.
Therefore, this series adds support for the "rx-internal-delay-ps" and
"tx-internal-delay-ps" properties inside sja1105 switch port DT nodes,
and if these are present, they will decide what RGMII delays will the
driver apply.
The in-tree device trees are also updated to follow the new format, as
well as the schema validator.
I assume it's okay to get all changes merged in through the same tree
(net-next). Although the DTS changes could be split, if needed - the
driver works with or without them. There is one more DTS which should be
changed, which is in Shawn's tree but not in net-next:
https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git/tree/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts?h=for-next
For that, I'd have to send a separate patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This change does not fix any functional issue or address any real life
use case that wasn't possible before. It is just a small step in the
process of standardizing the way in which Ethernet MAC drivers may apply
RGMII delays (traditionally these have been applied by PHYs, with no
clear definition of what to do in the case of a fixed-link).
The sja1105 driver used to apply MAC-level RGMII delays on the RX data
lines when in fixed-link mode and using a phy-mode of "rgmii-rxid" or
"rgmii-id" and on the TX data lines when using "rgmii-txid" or "rgmii-id".
But the standard definitions don't say anything about behaving
differently when the port is in fixed-link vs when it isn't, and the new
device tree bindings are about having a way of applying the delays in a
way that is independent of the phy-mode and of the fixed-link property.
When the {rx,tx}-internal-delay-ps properties are present, use them,
otherwise fall back to the old behavior and warn.
One other thing to note is that the SJA1105 hardware applies a delay
value in degrees rather than in picoseconds (the delay in ps changes
depending on the frequency of the RGMII clock - 125 MHz at 1G, 25 MHz at
100M, 2.5MHz at 10M). I assume that is fine, we calculate the phase
shift of the internal delay lines assuming that the device tree meant
gigabit, and we let the hardware scale those according to the link speed.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20210723173108.459770-6-prasanna.vengateshan@microchip.com/
Link: https://patchwork.ozlabs.org/project/netdev/patch/20200616074955.GA9092@laureti-dev/#2461123
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a schema validator to nxp,sja1105.yaml and to dsa.yaml for explicit
MAC-level RGMII delays. These properties must be per port and must be
present only for a phy-mode that represents RGMII.
We tell dsa.yaml that these port properties might be present, we also
define their valid values for SJA1105. We create a common definition for
the RX and TX valid range, since it's quite a mouthful.
We also modify the example to include the explicit RGMII delay properties.
On the fixed-link ports (in the example, port 4), having these explicit
delays is actually mandatory, since with the new behavior, the driver
shouts that it is interpreting what delays to apply based on phy-mode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since a switch is basically a bunch of Ethernet controllers, just
inherit the common schema for one to get stronger type validation of the
properties of a port.
For example, before this change it was valid to have a phy-mode = "xfi"
even if "xfi" is not part of ethernet-controller.yaml, now it is not.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All ports require either a phy-handle or a fixed-link, and port 3 in the
example didn't have one. Add it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 09e856d54bda5f288ef8437a90ab2b9b3eab83d1.
When an interface is enslaved in a VRF, prerouting conntrack hook is
called twice: once in the context of the original input interface, and
once in the context of the VRF interface. If no special precausions are
taken, this leads to creation of two conntrack entries instead of one,
and breaks SNAT.
Commit above was intended to avoid creation of extra conntrack entries
when input interface is enslaved in a VRF. It did so by resetting
conntrack related data associated with the skb when it enters VRF context.
However it breaks netfilter operation. Imagine a use case when conntrack
zone must be assigned based on the original input interface, rather than
VRF interface (that would make original interfaces indistinguishable). One
could create netfilter rules similar to these:
chain rawprerouting {
type filter hook prerouting priority raw;
iif realiface1 ct zone set 1 return
iif realiface2 ct zone set 2 return
}
This works before the mentioned commit, but not after: zone assignment
is "forgotten", and any subsequent NAT or filtering that is dependent
on the conntrack zone does not work.
Here is a reproducer script that demonstrates the difference in behaviour.
==========
#!/bin/sh
# This script demonstrates unexpected change of nftables behaviour
# caused by commit 09e856d54bda5f28 ""vrf: Reset skb conntrack
# connection on VRF rcv"
# https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=09e856d54bda5f288ef8437a90ab2b9b3eab83d1
#
# Before the commit, it was possible to assign conntrack zone to a
# packet (or mark it for `notracking`) in the prerouting chanin, raw
# priority, based on the `iif` (interface from which the packet
# arrived).
# After the change, # if the interface is enslaved in a VRF, such
# assignment is lost. Instead, assignment based on the `iif` matching
# the VRF master interface is honored. Thus it is impossible to
# distinguish packets based on the original interface.
#
# This script demonstrates this change of behaviour: conntrack zone 1
# or 2 is assigned depending on the match with the original interface
# or the vrf master interface. It can be observed that conntrack entry
# appears in different zone in the kernel versions before and after
# the commit.
IPIN=172.30.30.1
IPOUT=172.30.30.2
PFXL=30
ip li sh vein >/dev/null 2>&1 && ip li del vein
ip li sh tvrf >/dev/null 2>&1 && ip li del tvrf
nft list table testct >/dev/null 2>&1 && nft delete table testct
ip li add vein type veth peer veout
ip li add tvrf type vrf table 9876
ip li set veout master tvrf
ip li set vein up
ip li set veout up
ip li set tvrf up
/sbin/sysctl -w net.ipv4.conf.veout.accept_local=1
/sbin/sysctl -w net.ipv4.conf.veout.rp_filter=0
ip addr add $IPIN/$PFXL dev vein
ip addr add $IPOUT/$PFXL dev veout
nft -f - <<__END__
table testct {
chain rawpre {
type filter hook prerouting priority raw;
iif { veout, tvrf } meta nftrace set 1
iif veout ct zone set 1 return
iif tvrf ct zone set 2 return
notrack
}
chain rawout {
type filter hook output priority raw;
notrack
}
}
__END__
uname -rv
conntrack -F
ping -W 1 -c 1 -I vein $IPOUT
conntrack -L
Signed-off-by: Eugene Crosser <crosser@average.org>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-16-kuba@kernel.org
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-15-kuba@kernel.org
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-14-kuba@kernel.org
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-13-kuba@kernel.org
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-11-kuba@kernel.org
netdev->dev_addr will be come const soon, constify the argument
to command send to avoid compiler warnings.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-10-kuba@kernel.org
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Use dev_addr_set() to match the existing logic.
setup_card() is always passed netdev->dev_addr, so pass the netdev
pointer instead and assign the address using a helper there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-9-kuba@kernel.org
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Use a buffer on the stack. Note that atmel_get_mib() is a wrapper
around atmel_copy_to_host(). For the to device direction we just
need to make sure functions respect argument being cost.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-7-kuba@kernel.org
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Do the special encoding on the stack, then copy the address.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-6-kuba@kernel.org
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Do the special encoding on the stack, then copy the address.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-5-kuba@kernel.org
Convert all WiFi drivers from memcpy(... dev->addr_len)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, dev->addr_len)
+ eth_hw_addr_set(dev, np)
Manually checked the netdevs are allocated with alloc_etherdev(),
so dev->addr_len must be equal to ETH_ALEN.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-4-kuba@kernel.org
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Convert wireless from ether_addr_copy() to eth_hw_addr_set():
@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018235021.1279697-3-kuba@kernel.org
The integrated So devices covered by the iwl_so_long_latency_trans_cfg
configuration should all have low-latency-xtal enabled, so do that.
While at it, remove the TODO, I've checked the other values as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 6f60fb03c8e7 ("iwlwifi: move SnJ and So rules to the new tables")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20211016114029.8b5480113f53.I80b5b4ebea84e56f3b3143fc1ee7097be8b4ae78@changeid
If the data we get from EFI is not even long enough for
the package struct we expect then ignore it entirely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: a1a6a4cf49ec ("iwlwifi: pnvm: implement reading PNVM from UEFI")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20211016114029.33feba783518.I54a5cf33975d0330792b3d208b225d479e168f32@changeid
If resume fails for some reason, we need to set the PM state
back to normal so we're able to send commands during firmware
reset, rather than failing all of them because we're in D3.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 708a39aaca22 ("iwlwifi: mvm: don't send commands during suspend\resume transition")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20211016114029.7ceb9eaca9f6.If0cbef38c6d07ec1ddce125878a4bdadcb35d2c9@changeid
ath.git patches for v5.16. Major changes:
ath9k
* add option to reset the wifi chip via debugfs
* convert Device Tree bindings to the json-schema
* support Device Tree ieee80211-freq-limit property to limit channels
When powersaving (so either wifi powersaving or deep sleep, depending on
which state the firmware is in) is disabled, the way the firmware goes
into host sleep is different: Usually the firmware implicitely enters
host sleep on the next SLEEP event we get when we configured host sleep
via HSCFG before. When powersaving is disabled though, there are no
SLEEP events, the way we enter host sleep in that case is different: The
firmware will send us a HS_ACT_REQ event and after that we "manually"
make the firmware enter host sleep by sending it another HSCFG command
with the action HS_ACTIVATE.
Now waking up from host sleep appears to be different depending on
whether powersaving is enabled again: When powersaving is enabled, the
firmware implicitely leaves host sleep as soon as it wakes up and sends
us an AWAKE event. When powersaving is disabled though, it apparently
doesn't implicitely leave host sleep, but instead we need to send it a
HSCFG command with the HS_CONFIGURE action and the HS_CFG_CANCEL
condition. We didn't do that so far, which is why waking up from host
sleep was broken when powersaving is disabled.
So add some additional state to mwifiex_adapter where we keep track of
whether host sleep was activated manually via HS_ACTIVATE, and if that
was the case, deactivate it manually again via HS_CFG_CANCEL.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-6-verdre@v0yd.nl
While looking at on-air packets using Wireshark, I noticed we're never
setting the initiator bit when sending DELBA requests to the AP: While
we set the bit on our del_ba_param_set bitmask, we forget to actually
copy that bitmask over to the command struct, which means we never
actually set the initiator bit.
Fix that and copy the bitmask over to the host_cmd_ds_11n_delba command
struct.
Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Acked-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-5-verdre@v0yd.nl
Sometimes the KEY_MATERIAL command can fail with the 88W8897 firmware
(when this happens exactly seems pretty random). This appears to prevent
the access point from starting, so it seems like a good idea to log an
error in that case.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-3-verdre@v0yd.nl
It's not an error if someone chooses to put their computer to sleep, not
wanting it to wake up because the person next door has just discovered
what a magic packet is. So change the loglevel of this annoying message
from ERROR to INFO.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-2-verdre@v0yd.nl
Fix the return value check which testing the wrong variable
in rtw89_cam_send_sec_key_cmd().
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e3ec7017f6a2 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018033102.1813058-1-yangyingliang@huawei.com
When fail to init coex module, free 'common' and 'adapter' directly, but
common->tx_thread which will access 'common' and 'adapter' is running at
the same time. That will trigger the UAF bug.
==================================================================
BUG: KASAN: use-after-free in rsi_tx_scheduler_thread+0x50f/0x520 [rsi_91x]
Read of size 8 at addr ffff8880076dc000 by task Tx-Thread/124777
CPU: 0 PID: 124777 Comm: Tx-Thread Not tainted 5.15.0-rc5+ #19
Call Trace:
dump_stack_lvl+0xe2/0x152
print_address_description.constprop.0+0x21/0x140
? rsi_tx_scheduler_thread+0x50f/0x520
kasan_report.cold+0x7f/0x11b
? rsi_tx_scheduler_thread+0x50f/0x520
rsi_tx_scheduler_thread+0x50f/0x520
...
Freed by task 111873:
kasan_save_stack+0x1b/0x40
kasan_set_track+0x1c/0x30
kasan_set_free_info+0x20/0x30
__kasan_slab_free+0x109/0x140
kfree+0x117/0x4c0
rsi_91x_init+0x741/0x8a0 [rsi_91x]
rsi_probe+0x9f/0x1750 [rsi_usb]
Stop thread before free 'common' and 'adapter' to fix it.
Fixes: 2108df3c4b18 ("rsi: add coex support")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211015040335.1021546-1-william.xuanziyang@huawei.com
Update max rx len of some hw modules, which aligns out vendor SDK.
In normal modes, we exchange MPDU 7991 cap with peers; however, this
won't play a part in sniffer mode.
To prevent packets which exceed the max MPDU size from entering specific
rx path in hw, we need to set a proper limit to filter them out.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix missing HE phy cap related to vif and starec setting.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Re-order and modify conditions for MU DL/UL and ofdma DL fields, and
also clean up some unnecessary zero settings.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable HE UL MU-MIMO in sta_rec_muru, which works on both ap and station
mode.
For sending trigger frames, one of the conditions fw uses is to check if
mib rx airtime meets the threshold.
There's a main control of mib rx airtime report register in fw, so we
need to enable the register by mcu cmd instead of directly writing it,
otherwise it will still be disabled by fw.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
