IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Patch from david.somayajulu@qlogic.com:
Add target discovery event. We may have a setup where the iscsi traffic
is on a different netowrk than the other network traffic. In this case
we will want to do discovery though the iscsi card. This patch adds
a event to the transport class that can be used by hw iscsi cards that
support this.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I noticed that in_use in st_buffer is not used. The patch below
against 2.6.17-rc3 removes it, assuming there is no future use for it.
It was tested in a sparc SS20 with a DLT4000.
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Acked-by: Kai Mkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/aacraid/comminit.c
Fixed up by removing the now renamed CONFIG_IOMMU option from
aacraid
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The atp870u driver is the largest stack eater reported by checkstack
(on x86_864, allmodconfig). This converts the offending function
to kmalloc+kfree struct atp_unit instead of allocating it on the stack.
Was:
0x0000164c atp870u_probe [atp870u]: 3176
Now:
0x0000164c atp870u_probe [atp870u]: 408
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* Adding 1078 ROC (Raid On Chip) Support - New host adapter
* Moving all PCI Vendor/Device ids to using internal defines; a request
from Christoph/James B. some time ago for when the next chip was added.
* Removing SAS 1066/1066E Vendor/Device IDs, as there are no plans to
manufacture that controller.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* Wide port support added - using James Bottomley's new SAS wide port API.
(There is a known problem in sas transport layer reported yesterday to
James. The Kobject dev.bus_ids for end devices are not unique across
expanders. I have added a work around in this patch, where I asigning
an unique port identifier for every port within the host - this solves
the problem, but I expect a fix from James in the sas transport).
* Adding target_alloc and target_destroy entry points, and moving code over
from the slave entry points.
* The renaming of some mptscsih_xxx functions declared in mptsas.c,
to mptsas_xxx.
* Target Reset moved from slave_destroy to hotplug work thread
handling (with regard to device removal). Also inhibit IO to end device
while device is being broken down . Talked to James Smart about this
at Linux Expo (with questions of how the fc transport handles this).
* Cleaning up the kzalloc's, and kfree's
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
this patch introduces a port object, separates out ports and phys,
with ports becoming the primary objects of the tree.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If a device gets offlined as a result of the Inquiry sent
during scanning, the following oops can occur. After the
disk gets put into the SDEV_OFFLINE state, the error handler
sends back the failed inquiry, which wakes the thread doing
the scan. This starts a race between the scanning thread
freeing the scsi device and the error handler calling
scsi_run_host_queues to restart the host. Since the disk
is in the SDEV_OFFLINE state, scsi_device_get will still
work, which results in __scsi_iterate_devices getting
a reference to the scsi disk when it shouldn't.
The following execution thread causes the oops:
CPU 0 (scan) CPU 1 (eh)
---------------------------------------------------------
scsi_probe_and_add_lun
....
scsi_eh_offline_sdevs
scsi_eh_flush_done_q
scsi_destroy_sdev
scsi_device_dev_release
scsi_restart_operations
scsi_run_host_queues
__scsi_iterate_devices
get_device
scsi_device_dev_release_usercontext
scsi_run_queue
<---OOPS--->
The patch fixes this by changing the state of the sdev to SDEV_DEL
before doing the final put_device, which should prevent the race
from occurring.
Original oops follows:
Badness in kref_get at lib/kref.c:32
Call Trace:
[C00000002F4476D0] [C00000000000EE20] .show_stack+0x68/0x1b0 (unreliable)
[C00000002F447770] [C00000000037515C] .program_check_exception+0x1cc/0x5a8
[C00000002F447840] [C00000000000446C] program_check_common+0xec/0x100
Exception: 700 at .kref_get+0x10/0x28
LR = .kobject_get+0x20/0x3c
[C00000002F447B30] [C00000002F447BC0] 0xc00000002f447bc0 (unreliable)
[C00000002F447BB0] [C000000000254BDC] .get_device+0x20/0x3c
[C00000002F447C30] [D000000000063188] .scsi_device_get+0x34/0xdc [scsi_mod]
[C00000002F447CC0] [D0000000000633EC] .__scsi_iterate_devices+0x50/0xbc [scsi_mod]
[C00000002F447D60] [D00000000006A910] .scsi_run_host_queues+0x34/0x5c [scsi_mod]
[C00000002F447DF0] [D000000000069054] .scsi_error_handler+0xdb4/0xe44 [scsi_mod]
[C00000002F447EE0] [C00000000007B4E0] .kthread+0x128/0x178
[C00000002F447F90] [C000000000025E84] .kernel_thread+0x4c/0x68
Unable to handle kernel paging request for <7>PCI: Enabling device: (0002:41:01.1), cmd 143
data at address 0x000001b8
Faulting instruction address: 0xd0000000000698e4
sym1: <1010-66> rev 0x1 at pci 0002:41:01.1 irq 216
sym1: No NVRAM, ID 7, Fast-80, LVD, parity checking
sym1: SCSI BUS has been reset.
scsi2 : sym-2.2.2
cpu 0x0: Vector: 300 (Data Access) at [c00000002f447a30]
pc: d0000000000698e4: .scsi_run_queue+0x2c/0x218 [scsi_mod]
lr: d00000000006a904: .scsi_run_host_queues+0x28/0x5c [scsi_mod]
sp: c00000002f447cb0
msr: 9000000000009032
dar: 1b8
dsisr: 40000000
current = 0xc0000000045fecd0
paca = 0xc00000000048ee80
pid = 1123, comm = scsi_eh_1
enter ? for help
[c00000002f447d60] d00000000006a904 .scsi_run_host_queues+0x28/0x5c [scsi_mod]
[c00000002f447df0] d000000000069054 .scsi_error_handler+0xdb4/0xe44 [scsi_mod]
[c00000002f447ee0] c00000000007b4e0 .kthread+0x128/0x178
[c00000002f447f90] c000000000025e84 .kernel_thread+0x4c/0x68
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a resend of a patch I generated in response to an email sent
by Ruben Faelens <parasietje@gmail.com>. His original email to
linux-scsi requested a method in which he could spin down a scsi disk
when not in use and have the kernel automatically spin it back up when
an I/O was generated to the disk. The infrastructure to automatically
spin a disk up has been in the scsi error handler for some time now,
but it is not enabled by default. This patch adds an sd sysfs attribute
which allows userspace to enable this behavior.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[netdrvr] Remove long-unused bits from Becker template drivers
[netdrvr] natsemi: minor cleanups
[netdrvr] natsemi: Separate out media initialization code
[PATCH] WAN: update info page for a bunch of my drivers
[PATCH] drivers/net/hamradio/dmascc.c: fix section mismatch
[PATCH] Fix phy id for LXT971A/LXT972A
[PATCH] DM9000 - minor code cleanups
[PATCH] DM9000 - do no re-init spin lock
[PATCH] DM9000 - check for MAC left in by bootloader
[PATCH] DM9000 - better checks for platform resources
Commit 02dd7ae289 ("[PATCH] i2c-i801:
Merge setup function") has a missing return 0 in the _probe() function.
This means the error path is always executed and pci_disable_device() is
called even when the device just got successfully enabled.
Having the SMBus device disabled makes some systems (eg.
Fujitsu-Siemens Lifebook E8010) hang hard during power-off.
Intead of reverting the whole commit this patch fixes it up:
- don't ever call pci_disable_device(), also not in the _remove() function
to avoid hangs
- fix missing pci_release_region() in error path
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Collection of fixes for the ColdFire FEC ethernet driver:
. reworked event setting so that it occurs after the MII setup.
roucaries bastien <roucaries.bastien@gmail.com>
. Do not read cbd_sc in memory for each bit we test. Once per buffer is enough.
. Overrun errors must increase `rx_fifo_errors', not `rx_crc_errors'
. No need for a special value to activate rx or tx. Only write access matters.
. Simplify parameter of eth_copy_and_sum : `data' has already the right value.
. Some spelling fixes.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Set different irq priority levels for each IRQ requested.
According to the Freescale ColdFire documentation each separate IRQ
must have its own unique priority/level combination.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the FEC module in the ColdFire 532x CPU family.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid requesting a `Graceful Transmit Stop' when link has disappeared,
because that request cannot complete without link.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (26 commits)
V4L/DVB (4263): Fix warning when compiling on 64 bit machines
V4L/DVB (4261): Included required header for in-kernel compilation
V4L/DVB (4260): Stradis.c: make 2 functions static
V4L/DVB (4259): Pass an explicit log prefix to cx2341x_log_status
V4L/DVB (4257): Fix 64-bit compile warnings.
V4L/DVB (4255): Tda9887 default TOP value is 0x10
V4L/DVB (4254): Remove obsoleted tuner_debug option.
V4L/DVB (4253): IVTV VBI format description too long.
V4L/DVB (4252): Remove duplicate 'tda9887' in info messages.
V4L/DVB (4245): Reduce the amount of pvrusb2-sourced noise going into the system log
V4L/DVB (4244): Implement use of cx2341x module in pvrusb2 driver
V4L/DVB (4243): Exploit new V4L control features in pvrusb2
V4L/DVB (4242): Don't suspend encoder when changing its attributes (in pvrusb2)
V4L/DVB (4241): Fix faulty encoder error recovery in pvrusb2
V4L/DVB (4240): Various V4L control enhancements in pvrusb2
V4L/DVB (4239): Handle boolean controls in pvrusb2
V4L/DVB (4238): Make sure flags field is initialized when quering a control in pvrusb2
V4L/DVB (4237): Move LOG_STATUS bracketing to a different part of the pvrusb2 driver
V4L/DVB (4236): Rearrange things in pvrusb2 driver in preparation for using cx2341x module
V4L/DVB (4235): Increase the maximum number of controls that pvrusb2-sysfs.c can handle.
...
DLE masking was non-functional since the new tty handling.
Found by Peter Evertz <leo2@pec.homeip.net>
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's available in a header as a static inline - there's no need to export it.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sysfs entries 'sched_mc_power_savings' and 'sched_smt_power_savings' in
/sys/devices/system/cpu/ control the MC/SMT power savings policy for the
scheduler.
Based on the values (1-enable, 0-disable) for these controls, sched groups
cpu power will be determined for different domains. When power savings
policy is enabled and under light load conditions, scheduler will minimize
the physical packages/cpu cores carrying the load and thus conserving
power(with a perf impact based on the workload characteristics... see OLS
2005 CMP kernel scheduler paper for more details..)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Con Kolivas <kernel@kolivas.org>
Cc: "Chen, Kenneth W" <kenneth.w.chen@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace the temp makefile hacks with proper CONFIG entries, which are also
added to Kconfig.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add current pin settings to gpio_dump() output. This adds the last 'word' to
the syslog lines, which displays the input and output values that the pin is
set to.
pc8736x_gpio.0: io00: 0x0044 TS OD PUE EDGE LO DEBOUNCE io:1/1
The 2 values may differ for a number of reasons:
1- the pin output circuitry is diaabled, (as the above 'TS' indicates)
2- it needs a pullup resistor to drive the attached circuit,
3- the external circuit needs a pullup so the open-drain has something
to pull-down
4- the pin is wired to Vcc or Ground
It might be appropriate to add a WARN for 2,3,4, since they could
damage the chip and/or circuit, esp if misconfig goes unnoticed.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hmm. Im somewhat ambivalent about this patch, since with it, driver wont
build for vanilla 17 or older.
Its also only 1/2 of your suggestion - when I tried it, I was building against
vanilla 17, and asm/uaccess.h cause compilation failure. Looking back, Im
perplexed as to why linux/io.h didnt cause same failure ?!?
use linux/io.h rather than asm/io.h
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace spinlocks guarding gpio config ops with mutexes. This is a me-too
patch, and is justifiable insofar as mutexes have stricter semantics and
better debugging support, so are preferred where they are applicable.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a working gpio_current() to pc8736x_gpio.c (the previous implementation
just threw a dev_warn), and fix gpio_change() to use gpio_current() rather
than the incorrect (and temporary) gpio_get(). Initialize shadow-regs so this
all works.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use of dev_dbg() and friends is considered good practice. dev_dbg() needs a
struct device *devp, but nsc_gpio is only a helper module, so it doesnt
have/need its own. To provide devp to the user-modules (scx200 & pc8736x
_gpio), we add it to the vtable, and set it during init.
Also squeeze nsc_gpio_dump()'s format a little.
[ 199.259879] pc8736x_gpio.0: io09: 0x0044 TS OD PUE EDGE LO DEBOUNCE
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds platform-device to (just introduced) driver, and uses it to replace many
printks with dev_dbg() etc. This could trivially be merged into previous
patch, but this way matches better with the corresponding patch that does the
same change to scx200_gpio.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the brand new pc8736x_gpio driver. This is mostly based upon
scx200_gpio.c, but the platform_dev is treated separately, since its fairly
big too.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since the meaning of config-bits is the same for scx200 and pc8736x _gpios, we
can share a function to deliver this to user. Since it is called via the
vtable, its also completely replaceable. For now, we keep using printk...
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that the read(), write() file-ops are dispatching gpio-ops via the vtable,
they are generic, and can be moved 'verbatim' to the nsc_gpio common-support
module. After the move, various symbols are renamed to update 'scx200_' to
'nsc_', and headers are adjusted accordingly.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the nsc_gpio common-support module as an empty shell. Next patch starts
the migration of the common gpio support routines.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now actually call the gpio operations thru the vtable.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Abstract the gpio operations into a new nsc_gpio_ops vtable.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new driver command: 'v' which calls gpio_dump() on the pin. The output
goes to the log, like all other INFO messages in the original driver. Giving
the user control over the feedback they 'need' is construed to be a
user-friendly feature, and allows us (later) to dial down many INFO messages
to DEBUG log-level.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a platform-device to scx200_gpio, and use its struct device dev member
(ie: devp) in dev_dbg() once.
There are 2 alternatives here (Im soliciting guidance/commentary):
- use isa_device, if/when its added to the kernel.
- alter scx200.c to EXPORT_GPL its private devp so that both scx200_gpio,
and the (to be added) nsc_gpio module can use it. Since the available devp
is in 'grandparent', this seems like too much 'action at a distance'.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adopt many modern 2.6 coding practices, ala LDD3, chapter 3. Changes are
limited to initialization calls from module init, ie: cdev_init, cdev_add,
*_chrdev_region, mkdev.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
GPIO SUPPORT FOR SCx200 & PC8736x
The patch-set reworks the 2.4 vintage scx200_gpio driver for modern 2.6, and
refactors GPIO support to reuse it in a new driver for the GPIO on PC-8736x
chips. Its handy for the Soekris.com net-4801, which has both chips.
These patches have been seen recently on Kernel-Mentors, and then
Kernel-Newbies ML, where Jesper Juhl kindly reviewed it. His feedback has
been incorporated. Thanks Jesper !
Its also gone to soekris-tech@soekris.com for possible testing by linux folks,
I've gotten 1 promise so far. Theyre mostly BSD folk over there, but we'll
see..
Device-file & Sysfs
The driver preserves the existing device-file interface, including the
write/cmd set, but adds v to 'view' the pin-settings & configs by inducing,
via gpio_dump(), a dev_info() call. Its a fairly crappy way to get status,
but it sticks to the syslog approach, conservatively.
Allowing users to voluntarily trigger logging is good, it gives them a
familiar way to confirm their app's control & use of the pins, and I've thus
reduced the pin-mode-updates from dev_info to dev_dbg.
I've recently bolted on a proto sysfs interface for both new drivers. Im not
including those patches here; they (the patch + doc-pre-patch) are still quite
raw (and unreviewed on KNML), and since they 'invent' a convention for GPIO, a
proper vetting is needed. Since this patchset is much bigger than my previous
ones, Id like to keep things simpler, and address it 1st, before bolting on
more stuff.
The driver-split
The Geode CPU and the PC-87366 Super-IO chip have GPIO units which share a
common pin-architecture (same pin features, with same bits controlling), but
with different addressing mechanics and port organizations.
The vintage driver expresses the pin capabilities with pin-mode commands
[OoPpTt],etc that change the pin configurations, and since the 2 chips share
pin-arch, we can reuse the read(), write() commands, once the implementation
is suitably adjusted.
The patchset adds a vtable: struct nsc_gpio_ops, to abstract the existing gpio
operations, then adjusts fileops.write() code to invoke operations via that
vtable. Driver specific open()s set private_data to the vtable so its
available for use by write().
The vtable gets the gpio_dump() too, since its user-friendly, and (could be
construed as) part of the current device-file interface. To support use of
dev_dbg() in write() & _dump(), the vtable gets a dev ptr too, set by both
scx200 & pc8736x _gpio drivers.
heres how the pins are presented in syslog:
[ 1890.176223] scx200_gpio.0: io00: 0x0044 TS OD PUE EDGE LO DEBOUNCE
[ 1890.287223] scx200_gpio.0: io01: 0x0003 OE PP PUD EDGE LO
nsc_gpio.c: new file is new home of several file-ops methods, which are
modified to get their vtable from filp->private_data, and use it where needed.
scx200_gpio.c: keeps some of its existing gpio routines, but now wires them up
via the vtable (they're invoked by nsc_gpio.c:nsc_gpio_write() thru this
vtable). A driver-spcific open() initializes filp->private_data with the
vtable.
Once the split is clean, and the scx200_gpio driver is working, we copy and
modify the function and variable names, and rework the access-method bodies
for the different addressing scheme.
Heres a working overview of the patchset:
# series file for GPIO
# Spring Cleaning
gpio-scx/patch.preclean # scripts/Lindent fixes, editor-ctrl comments
# API Modernization
gpio-scx/patch.api26 # what I learned from LDD3
gpio-scx/patch.platform-dev-2 # get pdev, support for dev_dbg()
gpio-scx/patch.unsigned-minor # fix to match std practice
# Debuggability
gpio-scx/patch.dump-diet # shrink gpio_dump()
gpio-scx/patch.viewpins # add new 'command' to call dump()
gpio-scx/patch.init-refactor # pull shadow-register init to sub
# Access-Abstraction (add vtable)
gpio-scx/patch.access-vtable # introduce nsg_gpio_ops vtable, w dump
gpio-scx/patch.vtable-calls # add & use the vtable in scx200_gpio
gpio-scx/patch.nscgpio-shell # add empty driver for common-fops
# move code under abstraction
gpio-scx/patch.migrate-fops # move file-ops methods from scx200_gpio
gpio-scx/patch.common-dump # mv scx200.c:scx200_gpio_dump() to nsc_gpio.c
gpio-scx/patch.add-pc8736x-gpio # add new driver, like old, w chip adapt
# gpio-scx/patch.add-DEBUG # enable all dev_dbg()s
# Cleanups
# finish printk -> dev_dbg() etc
gpio-scx/patch.pdev-pc8736x # new drvr needs pdev too,
gpio-scx/patch.devdbg-nscgpio # add device to 'vtable', use in dev_dbg()
# gpio-scx/patch.pin-config-view # another 'c' 'command'
# gpio-scx/quiet-getset # take out excess dbg stuff (pretty quiet
now)
gpio-scx/patch.shadow-current # imitate scx200_gpio's shadow regs in
pc87*
# post KMentors-post patches ..
gpio-scx/patch.mutexes # use mutexes for config-locks
gpio-scx/patch.viewpins-values # extend dump to obsolete separate 'c' cmd
gpio-scx/patch.kconfig # add stuff for kbuild
# TBC
# combine api26 with pdev, which is just one step.
# merge c&v commands to single do-all-fn
# delay viewpins, dump-diet should also un-ifdef it too.
diff.sys-gpio-rollup-1
This patch:
Removed editor format-control comments, and used scripts/Lindent to clean up
whitespace, then deleted the bogus chunks :-(
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make notifier_blocks associated with cpu_notifier as __cpuinitdata.
__cpuinitdata makes sure that the data is init time only unless
CONFIG_HOTPLUG_CPU is defined.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CPUs come online only at init time (unless CONFIG_HOTPLUG_CPU is defined).
So, cpu_notifier functionality need to be available only at init time.
This patch makes register_cpu_notifier() available only at init time, unless
CONFIG_HOTPLUG_CPU is defined.
This patch exports register_cpu_notifier() and unregister_cpu_notifier() only
if CONFIG_HOTPLUG_CPU is defined.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In 2.6.17, there was a problem with cpu_notifiers and XFS. I provided a
band-aid solution to solve that problem. In the process, i undid all the
changes you both were making to ensure that these notifiers were available
only at init time (unless CONFIG_HOTPLUG_CPU is defined).
We deferred the real fix to 2.6.18. Here is a set of patches that fixes the
XFS problem cleanly and makes the cpu notifiers available only at init time
(unless CONFIG_HOTPLUG_CPU is defined).
If CONFIG_HOTPLUG_CPU is defined then cpu notifiers are available at run
time.
This patch reverts the notifier_call changes made in 2.6.17
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to serialize access to the global rtc_idr even in this error path.
Signed-off-by: Sonny Rao <sonny@burdell.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are two locking sets involved. One locks the board mappings and the
other is the tty open/close locking. The low level code was clearly
designed to be ported to OS's with spin locks already so pretty much comes
out in the wash
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Corey Minyard <minyard@acm.org>
The kthread used to speed up polling for IPMI was using udelay in its
busy-wait polling loop when the lower-level state machine told it to do a
short delay. This just used CPU and didn't help scheduling, thus causing
bad problems with other tasks. Call schedule() instead.
Signed-off-by: Corey Minyard <minyard@acm.org>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix TCSBRK comment to prevent confusion or accidental removal.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
locking init cleanups:
- convert " = SPIN_LOCK_UNLOCKED" to spin_lock_init() or DEFINE_SPINLOCK()
- convert rwlocks in a similar manner
this patch was generated automatically.
Motivation:
- cleanliness
- lockdep needs control of lock initialization, which the open-coded
variants do not give
- it's also useful for -rt and for lock debugging in general
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
