IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Critical trip points appear in the DTS thermal zones only after those
thermal zones have been registered via intel_soc_dts_iosf_init().
Moreover, they are "created" by changing the type of an existing trip
point from THERMAL_TRIP_PASSIVE to THERMAL_TRIP_CRITICAL via
intel_soc_dts_iosf_add_read_only_critical_trip(), the caller of which
has to be careful enough to pass at least 1 as the number of read-only
trip points to intel_soc_dts_iosf_init() beforehand.
This is questionable, because user space may have started to use the
trips at the time when intel_soc_dts_iosf_add_read_only_critical_trip()
runs and there is no synchronization between it and sys_set_trip_temp().
To address it, use the observation that nonzero number of read-only
trip points is only passed to intel_soc_dts_iosf_init() when critical
trip points are going to be used, so in fact that function may get all
of the information regarding the critical trip points upfront and it
can configure them before registering the corresponding thermal zones.
Accordingly, replace the read_only_trip_count argument of
intel_soc_dts_iosf_init() with a pair of new arguments related to
critical trip points: a bool one indicating whether or not critical
trip points are to be used at all and an int one representing the
critical trip point temperature offset relative to Tj_max. Use these
arguments to configure the critical trip points before the registration
of the thermal zones and to compute the number of writeable trip points
in add_dts_thermal_zone().
Modify both callers of intel_soc_dts_iosf_init() to take these changes
into account and drop the intel_soc_dts_iosf_add_read_only_critical_trip()
call, that is not necessary any more, from intel_soc_thermal_init(),
which also allows it to return success right after requesting the IRQ.
Finally, drop intel_soc_dts_iosf_add_read_only_critical_trip()
altogether, because it does not have any more users.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Because trip points are reset for each sensor in two places in the
same way, add a helper function for that to reduce code duplication
a bit.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
The initial configuration of trip points in intel_soc_dts_iosf_init()
takes place after registering the sensor thermal zones which is
potentially problematic, because it may race with the setting of trip
point temperatures via sysfs, as there is no synchronization between it
and sys_set_trip_temp().
To address this, change the initialization ordering so that the trip
points are configured prior to the registration of thermal zones.
Accordingly, change the cleanup ordering in intel_soc_dts_iosf_exit()
to remove the thermal zones before resetting the trip points.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
After previous changes, update_trip_temp() only uses its dts argument to
get to the sensors field in the struct intel_soc_dts_sensor_entry object
pointed to by that argument, so pass the value of that field directly to
it instead.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Function update_trip_temp() is currently used for the initialization
of trip points as well as for changing trip point temperatures in
sys_set_trip_temp().
This is quite confusing and passing the value of dts->trip_types[trip]
to it so that it can store that value in the same memory location is
not particularly useful, because it only is necessary to set the
trip point type once, at the initialization time.
For this reason, drop the last argument from update_trip_temp() and
introduce configure_trip() calling the former internally for the
initial configuration of trip points.
Modify the majority of update_trip_temp() callers to use
configure_trip() instead of it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
None of the existing callers of intel_soc_dts_iosf_init() passes
INTEL_SOC_DTS_INTERRUPT_NONE as the first argument to it, so the
notification local variable in it is always true and the
notification_support argument of add_dts_thermal_zone() is always
true either.
For this reason, drop the notification local variable from
intel_soc_dts_iosf_init() and the notification_support argument from
add_dts_thermal_zone() and rearrange the latter to always set
writable_trip_cnt and trip_mask.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
SOC_MAX_DTS_SENSORS is already defined in intel_soc_dts_iosf.h which is
included in intel_soc_dts_iosf.c, so it does not need to be defined in
the latter again.
Drop the redundant definition of that symbol from intel_soc_dts_iosf.c.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Both the existing callers of intel_soc_dts_iosf_init() pass 2 as the trip
count argument, so it can be replaced with SOC_MAX_DTS_TRIPS everywhere in
the code and the trip_count argument of that function can be dropped.
This also allows the trip_count field to be dropped from struct
intel_soc_dts_sensor_entry, as it is always equal to 2, and some
related code can be simplified.
Make changes accordingly.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
The driver is accessing the thermal zone state to ensure the state is
different from the one we want to set.
We don't want the driver to access the thermal zone device internals.
Actually, the thermal core code already checks if the thermal zone's
state is different before calling this function, thus this check is
duplicate.
Remove it.
Acked-by: srinivas pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use the thermal core API to access the thermal zone "type" field
instead of directly using the structure field. While here, remove
access to the temperature field, as this driver is reporting fake
temperature, which can be replaced with INT3400_FAKE_TEMP. Also
replace hardcoded 20C with INT3400_FAKE_TEMP
Acked-by: srinivas pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Add new IOCTLs to the int340x thermal driver to allow user space to
retrieve the Passive v2 thermal table (Srinivas Pandruvada).
- Add DT bindings for SM6375, MSM8226 and QCM2290 Qcom platforms (Konrad
Dybcio).
- Add DT bindings and support for QCom MSM8226 (Matti Lehtimäki).
- Add DT bindings for QCom ipq9574 (Praveenkumar I).
- Convert bcm2835 DT bindings to the yaml schema (Stefan Wahren).
- Allow selecting the bang-bang governor as default (Thierry Reding).
- Refactor and prepare the code to set the scene for RCar Gen4 (Wolfram
Sang).
- Clean up and fix the QCom tsens drivers. Add DT bindings and
calibration for the MSM8909 platform (Stephan Gerhold).
- Revert a patch introducing a wrong usage of devm_of_iomap() on the
Mediatek platform (Ricardo Cañuelo).
- Fix the clock vs reset ordering in order to conform to the
documentation on the sun8i (Christophe JAILLET).
- Prevent setting up undocumented registers, enable the only described
sensors and add the version 2.1 on the Qoriq sensor (Peng Fan).
- Add DT bindings and support for the Armada AP807 (Alex Leibovich).
- Update the mlx5 driver with the recent thermal changes (Daniel
Lezcano).
- Convert to platform remove callback returning void on STM32 (Uwe
Kleine-König).
- Add an error information printing for devm_thermal_add_hwmon_sysfs()
and remove the error from the Sun8i, Amlogic, i.MX, TI, K3, Tegra,
Qoriq, Mediateka and QCom (Yangtao Li).
- Register as hwmon sensor for the Generic ADC (Chen-Yu Tsai).
- Use the dev_err_probe() function in the QCom tsens alarm driver (Luca
Weiss).
-----BEGIN PGP SIGNATURE-----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=dtvf
-----END PGP SIGNATURE-----
Merge tag 'thermal-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These extend the int340x thermal driver, add thermal DT bindings for
some Qcom platforms, add DT bindings and support for Armada AP807 and
MSM8909, allow selecting the bang-bang thermal governor as the default
one, address issues in several thermal drivers for ARM platforms and
clean up code.
Specifics:
- Add new IOCTLs to the int340x thermal driver to allow user space to
retrieve the Passive v2 thermal table (Srinivas Pandruvada)
- Add DT bindings for SM6375, MSM8226 and QCM2290 Qcom platforms
(Konrad Dybcio)
- Add DT bindings and support for QCom MSM8226 (Matti Lehtimäki)
- Add DT bindings for QCom ipq9574 (Praveenkumar I)
- Convert bcm2835 DT bindings to the yaml schema (Stefan Wahren)
- Allow selecting the bang-bang governor as default (Thierry Reding)
- Refactor and prepare the code to set the scene for RCar Gen4
(Wolfram Sang)
- Clean up and fix the QCom tsens drivers. Add DT bindings and
calibration for the MSM8909 platform (Stephan Gerhold)
- Revert a patch introducing a wrong usage of devm_of_iomap() on the
Mediatek platform (Ricardo Cañuelo)
- Fix the clock vs reset ordering in order to conform to the
documentation on the sun8i (Christophe JAILLET)
- Prevent setting up undocumented registers, enable the only
described sensors and add the version 2.1 on the Qoriq sensor (Peng
Fan)
- Add DT bindings and support for the Armada AP807 (Alex Leibovich)
- Update the mlx5 driver with the recent thermal changes (Daniel
Lezcano)
- Convert to platform remove callback returning void on STM32 (Uwe
Kleine-König)
- Add an error information printing for devm_thermal_add_hwmon_sysfs()
and remove the error from the Sun8i, Amlogic, i.MX, TI, K3, Tegra,
Qoriq, Mediateka and QCom (Yangtao Li)
- Register as hwmon sensor for the Generic ADC (Chen-Yu Tsai)
- Use the dev_err_probe() function in the QCom tsens alarm driver
(Luca Weiss)"
* tag 'thermal-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (39 commits)
thermal/drivers/qcom/temp-alarm: Use dev_err_probe
thermal/drivers/generic-adc: Register thermal zones as hwmon sensors
thermal/drivers/mediatek/lvts_thermal: Remove redundant msg in lvts_ctrl_start()
thermal/drivers/qcom: Remove redundant msg at probe time
thermal/drivers/ti-soc: Remove redundant msg in ti_thermal_expose_sensor()
thermal/drivers/qoriq: Remove redundant msg in qoriq_tmu_register_tmu_zone()
thermal/drivers/tegra: Remove redundant msg in tegra_tsensor_register_channel()
drivers/thermal/k3: Remove redundant msg in k3_bandgap_probe()
thermal/drivers/imx: Remove redundant msg in imx8mm_tmu_probe() and imx_sc_thermal_probe()
thermal/drivers/amlogic: Remove redundant msg in amlogic_thermal_probe()
thermal/drivers/sun8i: Remove redundant msg in sun8i_ths_register()
thermal/hwmon: Add error information printing for devm_thermal_add_hwmon_sysfs()
thermal/drivers/stm32: Convert to platform remove callback returning void
net/mlx5: Update the driver with the recent thermal changes
thermal/drivers/armada: Add support for AP807 thermal data
dt-bindings: armada-thermal: Add armada-ap807-thermal compatible
thermal/drivers/qoriq: Support version 2.1
thermal/drivers/qoriq: Only enable supported sensors
thermal/drivers/qoriq: No need to program site adjustment register
thermal/drivers/mediatek/lvts_thermal: Register thermal zones as hwmon sensors
...
- Introduce power capping core support for Intel TPMI (Topology Aware
Register and PM Capsule Interface) and a TPMI interface driver for
Intel RAPL (Zhang Rui, Dan Carpenter).
- Fix CONFIG_IOSF_MBI dependency in the Intel RAPL power capping
driver (Zhang Rui).
- Fix invalid initialization for pl4_supported field in the Intel RAPL
power capping driver (Sumeet Pawnikar).
- Clean up the intel_idle driver, make it work with VM guests that
cannot use the MWAIT instruction and address the case in which the
host may enter a deep idle state when the guest is idle (Arjan van
de Ven).
- Prevent cpufreq drivers that provide the ->adjust_perf() callback
without a ->fast_switch() one which is used as a fallback from the
former in some cases (Wyes Karny).
- Fix some issues related to the AMD P-state cpufreq driver (Mario
Limonciello, Wyes Karny).
- Fix the energy_performance_preference attribute handling in the
intel_pstate driver in passive mode (Tero Kristo).
- Fix the handling of pm_suspend_target_state when CONFIG_PM is unset
(Kai-Heng Feng).
- Correct spelling mistake in a comment in the hibernation code (Wang
Honghui).
- Add arch_resume_nosmt() prototype to avoid a "missing prototypes"
build warning (Arnd Bergmann).
- Restrict pm_pr_dbg() to system-wide power transitions and use it in
a few additional places (Mario Limonciello).
- Drop verification of in-params from genpd_add_device() and ensure
that all of its callers will do it (Ulf Hansson).
- Prevent possible integer overflows from occurring in
genpd_parse_state() (Nikita Zhandarovich).
- Reorder fieldls in 'struct devfreq_dev_status' to reduce its size
somewhat (Christophe JAILLET).
- Ensure that the Exynos PPMU driver is already loaded before the
Exynos Bus driver starts probing so as to avoid a possible freeze
loading of the kernel modules (Marek Szyprowski).
- Fix variable deferencing before NULL check in the mtk-cci devfreq
driver (Sukrut Bellary).
-----BEGIN PGP SIGNATURE-----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=SZV7
-----END PGP SIGNATURE-----
Merge tag 'pm-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These add Intel TPMI (Topology Aware Register and PM Capsule
Interface) support to the power capping subsystem, extend the
intel_idle driver to work in VM guests where MWAIT is not available,
extend the system-wide power management diagnostics, fix bugs and
clean up code.
Specifics:
- Introduce power capping core support for Intel TPMI (Topology Aware
Register and PM Capsule Interface) and a TPMI interface driver for
Intel RAPL (Zhang Rui, Dan Carpenter)
- Fix CONFIG_IOSF_MBI dependency in the Intel RAPL power capping
driver (Zhang Rui)
- Fix invalid initialization for pl4_supported field in the Intel
RAPL power capping driver (Sumeet Pawnikar)
- Clean up the intel_idle driver, make it work with VM guests that
cannot use the MWAIT instruction and address the case in which the
host may enter a deep idle state when the guest is idle (Arjan van
de Ven)
- Prevent cpufreq drivers that provide the ->adjust_perf() callback
without a ->fast_switch() one which is used as a fallback from the
former in some cases (Wyes Karny)
- Fix some issues related to the AMD P-state cpufreq driver (Mario
Limonciello, Wyes Karny)
- Fix the energy_performance_preference attribute handling in the
intel_pstate driver in passive mode (Tero Kristo)
- Fix the handling of pm_suspend_target_state when CONFIG_PM is unset
(Kai-Heng Feng)
- Correct spelling mistake in a comment in the hibernation code (Wang
Honghui)
- Add arch_resume_nosmt() prototype to avoid a "missing prototypes"
build warning (Arnd Bergmann)
- Restrict pm_pr_dbg() to system-wide power transitions and use it in
a few additional places (Mario Limonciello)
- Drop verification of in-params from genpd_add_device() and ensure
that all of its callers will do it (Ulf Hansson)
- Prevent possible integer overflows from occurring in
genpd_parse_state() (Nikita Zhandarovich)
- Reorder fieldls in 'struct devfreq_dev_status' to reduce its size
somewhat (Christophe JAILLET)
- Ensure that the Exynos PPMU driver is already loaded before the
Exynos Bus driver starts probing so as to avoid a possible freeze
loading of the kernel modules (Marek Szyprowski)
- Fix variable deferencing before NULL check in the mtk-cci devfreq
driver (Sukrut Bellary)"
* tag 'pm-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (42 commits)
intel_idle: Add a "Long HLT" C1 state for the VM guest mode
cpufreq: intel_pstate: Fix energy_performance_preference for passive
cpufreq: amd-pstate: Add a kernel config option to set default mode
cpufreq: amd-pstate: Set a fallback policy based on preferred_profile
ACPI: CPPC: Add definition for undefined FADT preferred PM profile value
cpufreq: amd-pstate: Set default governor to schedutil
PM: domains: Move the verification of in-params from genpd_add_device()
cpufreq: amd-pstate: Make amd-pstate EPP driver name hyphenated
cpufreq: amd-pstate: Write CPPC enable bit per-socket
intel_idle: Add support for using intel_idle in a VM guest using just hlt
cpufreq: Fail driver register if it has adjust_perf without fast_switch
intel_idle: clean up the (new) state_update_enter_method function
intel_idle: refactor state->enter manipulation into its own function
platform/x86/amd: pmc: Use pm_pr_dbg() for suspend related messages
pinctrl: amd: Use pm_pr_dbg to show debugging messages
ACPI: x86: Add pm_debug_messages for LPS0 _DSM state tracking
include/linux/suspend.h: Only show pm_pr_dbg messages at suspend/resume
powercap: RAPL: Fix a NULL vs IS_ERR() bug
powercap: RAPL: Fix CONFIG_IOSF_MBI dependency
powercap: RAPL: fix invalid initialization for pl4_supported field
...
Dybcio)
- Add DT bindings and support for QCom MSM8226 (Matti Lehtimäki)
- Add DT bindings for QCom ipq9574 (Praveenkumar I)
- Convert bcm2835 DT bindings to the yaml schema (Stefan Wahren)
- Allow selecting the bang-bang governor as default (Thierry Reding)
- Refactor and prepare the code to set the scene for RCar Gen4
(Wolfram Sang)
- Cleanup and fixes for the QCom tsens drivers. Add DT bindings and
calibration for the MSM8909 platform (Stephan Gerhold)
- Revert a patch introducing a wrong usage of devm_of_iomap() on the
Mediatek platform (Ricardo Cañuelo)
- Fix the clock vs reset ordering in order to conform to the
documentation on the sun8i (Christophe JAILLET)
- Prevent setting up undocumented registers, enable the only described
sensors and add the version 2.1 on the Qoriq sensor (Peng Fan)
- Add DT bindings and support for the Armada AP807 (Alex Leibovich)
- Update the mlx5 driver with the recent thermal changes (Daniel
Lezcano)
- Convert to platform remove callback returning void on STM32 (Uwe
Kleine-König)
- Add an error information printing for devm_thermal_add_hwmon_sysfs()
and remove the error from the Sun8i, Amlogic, i.MX, TI, K3, Tegra,
Qoriq, Mediateka and QCom (Yangtao Li)
- Register as hwmon sensor for the Generic ADC (Chen-Yu Tsai)
- Use the dev_err_probe() function in the QCom tsens alarm driver
(Luca Weiss)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAmSZrHQACgkQqDIjiipP
6E9yrAf+KD4AO8piKP8RoFAwM5TDHz7lQFsf9kcIHA4OjDG9HYG7nV9Y3zlVRb5S
q4M/e69OCmQBWkntAuNwf3szl5ear7tutJjZb8pCKqQEp83gjyHnK3CrhGYTTFq4
CWafhhsXhZX9a0twtPoXCO4xD1jxay1Viv0I4uWB8QcNuQbDHYJP9eQtGkppn4ql
RRYZiYrlsjQ1uyylZ3fEbwcRGT6OGws5xSAhvya+MaU/czEWbjUFpJu37RGobvZ9
AI8GL4RD46IMsIvrb9xULJu3Fh5j+0Paj7hi6YGQqWPrKvhSFJ8cwc5M0oazslB3
P02n345laVmGvSskpT64nGZ2ArKr/Q==
=ZMIC
-----END PGP SIGNATURE-----
Merge tag 'thermal-v6.5-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thermal/linux into thermal
Pull thermal control updates for 6.5-rc1 from Daniel Lezcano:
"- Add DT bindings for SM6375, MSM8226 and QCM2290 Qcom platforms (Konrad
Dybcio)
- Add DT bindings and support for QCom MSM8226 (Matti Lehtimäki)
- Add DT bindings for QCom ipq9574 (Praveenkumar I)
- Convert bcm2835 DT bindings to the yaml schema (Stefan Wahren)
- Allow selecting the bang-bang governor as default (Thierry Reding)
- Refactor and prepare the code to set the scene for RCar Gen4
(Wolfram Sang)
- Cleanup and fixes for the QCom tsens drivers. Add DT bindings and
calibration for the MSM8909 platform (Stephan Gerhold)
- Revert a patch introducing a wrong usage of devm_of_iomap() on the
Mediatek platform (Ricardo Cañuelo)
- Fix the clock vs reset ordering in order to conform to the
documentation on the sun8i (Christophe JAILLET)
- Prevent setting up undocumented registers, enable the only described
sensors and add the version 2.1 on the Qoriq sensor (Peng Fan)
- Add DT bindings and support for the Armada AP807 (Alex Leibovich)
- Update the mlx5 driver with the recent thermal changes (Daniel
Lezcano)
- Convert to platform remove callback returning void on STM32 (Uwe
Kleine-König)
- Add an error information printing for devm_thermal_add_hwmon_sysfs()
and remove the error from the Sun8i, Amlogic, i.MX, TI, K3, Tegra,
Qoriq, Mediateka and QCom (Yangtao Li)
- Register as hwmon sensor for the Generic ADC (Chen-Yu Tsai)
- Use the dev_err_probe() function in the QCom tsens alarm driver
(Luca Weiss)"
* tag 'thermal-v6.5-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (38 commits)
thermal/drivers/qcom/temp-alarm: Use dev_err_probe
thermal/drivers/generic-adc: Register thermal zones as hwmon sensors
thermal/drivers/mediatek/lvts_thermal: Remove redundant msg in lvts_ctrl_start()
thermal/drivers/qcom: Remove redundant msg at probe time
thermal/drivers/ti-soc: Remove redundant msg in ti_thermal_expose_sensor()
thermal/drivers/qoriq: Remove redundant msg in qoriq_tmu_register_tmu_zone()
thermal/drivers/tegra: Remove redundant msg in tegra_tsensor_register_channel()
drivers/thermal/k3: Remove redundant msg in k3_bandgap_probe()
thermal/drivers/imx: Remove redundant msg in imx8mm_tmu_probe() and imx_sc_thermal_probe()
thermal/drivers/amlogic: Remove redundant msg in amlogic_thermal_probe()
thermal/drivers/sun8i: Remove redundant msg in sun8i_ths_register()
thermal/hwmon: Add error information printing for devm_thermal_add_hwmon_sysfs()
thermal/drivers/stm32: Convert to platform remove callback returning void
net/mlx5: Update the driver with the recent thermal changes
thermal/drivers/armada: Add support for AP807 thermal data
dt-bindings: armada-thermal: Add armada-ap807-thermal compatible
thermal/drivers/qoriq: Support version 2.1
thermal/drivers/qoriq: Only enable supported sensors
thermal/drivers/qoriq: No need to program site adjustment register
thermal/drivers/mediatek/lvts_thermal: Register thermal zones as hwmon sensors
...
Merge power capping updates for 6.5-rc1:
- Introduce power capping core support for Intel TPMI (Topology Aware
Register and PM Capsule Interface) and a TPMI interface driver for
Intel RAPL (Zhang Rui, Dan Carpenter).
- Fix CONFIG_IOSF_MBI dependency in the Intel RAPL power capping
driver (Zhang Rui).
- Fix invalid initialization for pl4_supported field in the Intel RAPL
power capping driver (Sumeet Pawnikar).
* powercap:
powercap: RAPL: Fix a NULL vs IS_ERR() bug
powercap: RAPL: Fix CONFIG_IOSF_MBI dependency
powercap: RAPL: fix invalid initialization for pl4_supported field
powercap: intel_rapl: Introduce RAPL TPMI interface driver
powercap: intel_rapl: Introduce core support for TPMI interface
powercap: intel_rapl: Introduce RAPL I/F type
powercap: intel_rapl: Make cpu optional for rapl_package
powercap: intel_rapl: Remove redundant cpu parameter
powercap: intel_rapl: Add support for lock bit per Power Limit
powercap: intel_rapl: Cleanup Power Limits support
powercap: intel_rapl: Use bitmap for Power Limits
powercap: intel_rapl: Change primitive order
powercap: intel_rapl: Use index to initialize primitive information
powercap: intel_rapl: Support per domain energy/power/time unit
powercap: intel_rapl: Support per Interface primitive information
powercap: intel_rapl: Support per Interface rapl_defaults
powercap: intel_rapl: Allow probing without CPUID match
powercap: intel_rapl: Remove unused field in struct rapl_if_priv
Use the dev_err_probe function instead of dev_err in the probe function
so that the printed message includes the return value and also handles
-EPROBE_DEFER nicely.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230625-spmi-temp-alarm-defer-v1-1-2d57acf36855@z3ntu.xyz
Register thermal zones as hwmon sensors to let userspace read
temperatures using standard hwmon interface.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
[Yangtao: only keep devm_thermal_add_hwmon_sysfs]
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-11-frank.li@vivo.com
The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-10-frank.li@vivo.com
The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-9-frank.li@vivo.com
The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-8-frank.li@vivo.com
The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-7-frank.li@vivo.com
The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-6-frank.li@vivo.com
The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-5-frank.li@vivo.com
The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-4-frank.li@vivo.com
The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-3-frank.li@vivo.com
The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-2-frank.li@vivo.com
Ensure that all error handling branches print error information. In this
way, when this function fails, the upper-layer functions can directly
return an error code without missing debugging information. Otherwise,
the error message will be printed redundantly or missing.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-1-frank.li@vivo.com
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
st_thermal_unregister() always returned zero, so convert it to return void
without any loss and then just drop the return from st_mmap_remove().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230616165641.1055854-1-u.kleine-koenig@pengutronix.de
Add support for the AP807 die thermal data. This is the same as AP806,
except for the coefficients.
ap807 values taken from TSENSE_ADC_16FFC spec, which says:
T(in Celsius) = T(code)*TSENE_GAIN+TSENE_OFFSET
where in default:
TSENE_OFFSET = 128.9
TSENE_GAIN = 0.394
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/E1qA7yU-00Ea4u-Je@rmk-PC.armlinux.org.uk
i.MX93 use TMU version 2.1, which supports:
- TRITSR_TP5(When this field is 1, you must add 0.5 K to the temperature
that TEMP reports. For example, if TEMP is 300 K and TP5=1, then the
final temperature is 300.5 K.)
- Has 16 TTRCR register: Temperature Range Control (TTRCR0 - TTRCR15)
This patch is to add this support.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230516083746.63436-4-peng.fan@oss.nxp.com
There are MAX 16 sensors, but not all of them supported. Such as
i.MX8MQ, there are only 3 sensors. Enabling all 16 sensors will
touch reserved bits from i.MX8MQ reference mannual, and TMU will stuck,
temperature will not update anymore.
Fixes: 45038e03d6 ("thermal: qoriq: Enable all sensors before registering them")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230516083746.63436-3-peng.fan@oss.nxp.com
No need to program site adjustment register, as programming
these registers do not give accurate value and also these
registers are not mentioned in Reference Manual.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230516083746.63436-2-peng.fan@oss.nxp.com
Register thermal zones as hwmon sensors to let userspace read
temperatures using standard hwmon interface.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230613091317.1691247-1-wenst@chromium.org
Should an error occur after calling sun8i_ths_resource_init() in the probe
function, some resources need to be released, as already done in the
.remove() function.
Switch to the devm_clk_get_enabled() helper and add a new devm_action to
turn sun8i_ths_resource_init() into a fully managed function.
Move the place where reset_control_deassert() is called so that the
recommended order of reset release/clock enable steps is kept.
A64 manual states that:
3.3.6.4. Gating and reset
Make sure that the reset signal has been released before the release of
module clock gating;
This fixes the issue and removes some LoC at the same time.
Fixes: dccc5c3b6f ("thermal/drivers/sun8i: Add thermal driver for H6/H5/H3/A64/A83T/R40")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/a8ae84bd2dc4b55fe428f8e20f31438bf8bb6762.1684089931.git.christophe.jaillet@wanadoo.fr
This reverts commit f05c7b7d9e.
That change was causing a regression in the generic-adc-thermal-probed
bootrr test as reported in the kernelci-results list [1].
A proper rework will take longer, so revert it for now.
[1] https://groups.io/g/kernelci-results/message/42660
Fixes: f05c7b7d9e ("thermal/drivers/mediatek: Use devm_of_iomap to avoid resource leak in mtk_thermal_probe")
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230525121811.3360268-1-ricardo.canuelo@collabora.com
According to the msm-3.18 vendor kernel from Qualcomm, mdm9607 needs
"correction factors" to adjust for additional offsets observed after the
factory calibration values in the fuses [1, 2].
The fixed offsets should be applied unless there is a special
calibration mode value that indicates that no offsets are needed [3].
Note that the new calibration mode values are called differently in this
patch compared to the vendor kernel:
- TSENS_TWO_POINT_CALIB_N_WA -> ONE_PT_CALIB2_NO_OFFSET
- TSENS_TWO_POINT_CALIB_N_OFFSET_WA -> TWO_PT_CALIB_NO_OFFSET
This is because close inspection of the calibration function [3] reveals
that TSENS_TWO_POINT_CALIB_N_WA is actually a "one point" calibration
because the if statements skip all "point2" related code for it.
[1]: d9d2db1b82
[2]: d75aef53a7
[3]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/blob/LE.UM.4.3.2.r1-04200-9x07/drivers/thermal/msm-tsens.c#L2987-3136
Fixes: a2149ab815 ("thermal/drivers/qcom/tsens-v0_1: Add support for MDM9607")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230508-msm8909-tsens-v5-3-5eb632235ba7@kernkonzept.com
The old single-cell parsing code was removed for MSM8939, MDM9607 and
MSM8976 but for some reason the structs defining the bit positions etc
were kept around (unused). Drop them now.
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 51d78b8b1b ("thermal/drivers/tsens: Drop single-cell code for mdm9607")
Fixes: dfadb4599a ("thermal/drivers/tsens: Drop single-cell code for msm8939")
Fixes: 3a908971f7 ("thermal/drivers/tsens: Drop single-cell code for msm8976/msm8956")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230508-msm8909-tsens-v5-1-5eb632235ba7@kernkonzept.com
For many setups the bang-bang governor is exactly what we want. Many
ARM SoC-based devices use fans to cool down the entire SoC and that
works well only with the bang-bang governor because it uses the
hysteresis in order to let the fan run for a while to cool the SoC
down below the trip point before switching it off again.
The step-wise governor will behave strangely in these situations. It
doesn't use the hysteresis, so it can lead to situations where the fan
is turned on for only a very brief period and then is switched back off,
only to get switched back on again very quickly because the SoC hasn't
cooled down very much.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20230609124408.3788680-1-thierry.reding@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The MSM8226 TSENS IP has 6 thermal sensors in a TSENS v0.1 block.
The thermal sensors use non-standard slope values.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230507201225.89694-4-matti.lehtimaki@gmail.com
The registers are differently named and at different offsets, but their
functionality is the same as for Gen3.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230511192220.7523-4-wsa+renesas@sang-engineering.com
Gen4 will be very different, so refactor Gen3 access into separate call
first.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230511192220.7523-3-wsa+renesas@sang-engineering.com
More items to describe the TSCs are needed soon, so encapsulate the
current 'ths_tj_1' item into a struct.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230511192220.7523-2-wsa+renesas@sang-engineering.com
Since commit 955fb8719e ("thermal/intel/intel_soc_dts_iosf: Use Intel
TCC library") intel_soc_dts_iosf is reporting the wrong temperature.
The driver expects tj_max to be in milli-degrees-celcius but after
the switch to the TCC library this is now in degrees celcius so
instead of e.g. 90000 it is set to 90 causing a temperature 45
degrees below tj_max to be reported as -44910 milli-degrees
instead of as 45000 milli-degrees.
Fix this by adding back the lost factor of 1000.
Fixes: 955fb8719e ("thermal/intel/intel_soc_dts_iosf: Use Intel TCC library")
Reported-by: Bernhard Krug <b.krug@elektronenpumpe.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: 6.3+ <stable@vger.kernel.org> # 6.3+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Export Passive version 2 table similar to the way _TRT and _ART tables
via IOCTLs.
This removes need for binary utility to read ACPI Passive 2 table by
providing open source support. This table already has open source
implementation in the user space thermald, when the table is part of
data vault exported by the int3400 sysfs.
This table is supported in some older platforms before Ice Lake
generation.
Passive 2 tables contain multiple entries. Each entry has following
fields:
* Source: Named Reference (String). This is the source device for
temperature.
* Target: Named Reference (String). This is the target device to
control.
* Priority: Priority of this device compared to others.
* SamplingPeriod: Time Period in 1/10 of seconds unit.
* PassiveTemp: Passive Temperature in 1/10 of Kelvin.
* SourceDomain: Domain for the source (00:Processor, others reserved).
* ControlKnob: Type of control knob (00:Power Limit 1, others: reserved)
* Limit: The target state to set on reaching passive temperature.
This can be a string "max", "min" or a power limit value.
* LimitStepSize: Step size during activation.
* UnLimitStepSize: Step size during deactivation.
* Reserved1: Reserved
Three IOCTLs are added similar to IOCTLs for reading TRT:
ACPI_THERMAL_GET_PSVT_COUNT: Number of passive 2 entries.
ACPI_THERMAL_GET_PSVT_LEN: Total return data size (count x each
passive 2 entry size).
ACPI_THERMAL_GET_PSVT: Get the data as an array of objects with
passive 2 entries.
This change is based on original development done by:
Todd Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog and subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Prior to the commit "763bd29fd3d1 ("thermal: int340x_thermal: Use
sysfs_emit_at() instead of scnprintf()", there was a new line after each
UUID string.
With the newline removed, existing user space like "thermald" fails to
compare each supported UUID as it is using getline() to read UUID and
apply correct thermal table.
To avoid breaking existing user space, add newline after each UUID string.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Fixes: 763bd29fd3 ("thermal: int340x_thermal: Use sysfs_emit_at() instead of scnprintf()")
Cc: 6.3+ <stable@vger.kernel.org> # 6.3+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Different RAPL Interfaces may have different primitive information and
rapl_defaults calls.
To better distinguish this difference in the RAPL framework code,
introduce a new enum to represent different types of RAPL Interfaces.
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Wang Wendy <wendy.wang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
MSR RAPL Interface always removes a rapl_package when all the CPUs in
that rapl_package are offlined. This is because it relies on an online
CPU to access the MSR.
But for RAPL Interface using MMIO registers, when all the cpus within
the rapl_package are offlined,
1. the register can still be accessed
2. monitoring and setting the Power Pimits for the rapl_package is still
meaningful because of uncore power.
This means that, a valid rapl_package doesn't rely on one or more cpus
being onlined.
For this sense, make cpu optional for rapl_package. A rapl_package can
be registered either using a CPU id to represent the physical
package/die, or using the physical package id directly.
Note that, the thermal throttling interrupt is not disabled via
MSR_IA32_PACKAGE_THERM_INTERRUPT for such rapl_package at the moment.
If it is still needed in the future, this can be achieved by selecting
an onlined CPU using the physical package id.
Note that, processor_thermal_rapl, the current MMIO RAPL Interface
driver, can also be converted to register using a package id instead.
But this is not done right now because processor_thermal_rapl driver
works on single-package systems only, and offlining the only package
will not happen. So keep the previous logic.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Wang Wendy <wendy.wang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, a RAPL package is registered with the number of Power Limits
supported in each RAPL domain. But this doesn't tell which Power Limits
are available. Using the number of Power Limits supported to guess the
availability of each Power Limit is fragile.
Use bitmap to represent the availability of each Power Limit.
Note that PL1 is mandatory thus it does not need to be set explicitly by
the RAPL Interface drivers.
No functional change intended.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Wang Wendy <wendy.wang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
