IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
KSZ8563R, which has same PHYID as KSZ9477 family, will change "EEE control
and capability 1" (Register 3.20) content depending on configuration of
"EEE advertisement 1" (Register 7.60). Changes on the 7.60 will affect
3.20 register.
So, instead of depending on register 3.20, driver should set supported_eee.
Proper supported_eee configuration is needed to make use of generic
PHY c45 set/get_eee functions provided by next patches.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for PHC and timestamping operations for the lan8841 PHY.
PTP 1-step and 2-step modes are supported, over Ethernet and UDP both
ipv4 and ipv6.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for cable diagnostics in lan8841 PHY. It has the same
registers layout as lan8814 PHY, therefore reuse the functionality.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230208114406.1666671-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The LAN8841 is completely integrated triple-speed (10BASE-T/ 100BASE-TX/
1000BASE-T) Ethernet physical layer transceivers for transmission and
reception of data on standard CAT-5, as well as CAT-5e and CAT-6,
unshielded twisted pair (UTP) cables.
The LAN8841 offers the industry-standard GMII/MII as well as the RGMII.
Some of the features of the PHY are:
- Wake on LAN
- Auto-MDIX
- IEEE 1588-2008 (V2)
- LinkMD Capable diagnosis
Currently the patch offers support only for link configuration.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the NULL pointer case
Fixes New smatch warnings:
drivers/net/phy/micrel.c:2613 lan8814_ptp_probe_once() warn: passing zero to 'PTR_ERR'
vim +/PTR_ERR +2613 drivers/net/phy/micrel.c
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialized return variable
Fixes Old smatch warnings:
drivers/net/phy/micrel.c:1750 ksz886x_cable_test_get_status() error:
uninitialized symbol 'ret'.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lan8814 represents a package of 4 PHYs. All of them are sharing the
same interrupt line. So when a link was going down/up or a frame was
timestamped, then the interrupt handler of all the PHYs was called.
Which is all fine and expected but the problem is the way the handler
interrupt works.
Basically if one of the PHYs timestamp a frame, then all the other 3
PHYs were polling the status of the interrupt until that PHY actually
cleared the interrupt by reading the timestamp.
The reason of polling was in case another PHY was also timestamping a
frame at the same time, it could miss this interrupt. But this is not
the right approach, because it is the interrupt controller who needs to
call the interrupt handlers again if the interrupt line is still
active.
Therefore change this such when the interrupt handler is called check
only if the interrupt is for itself, otherwise just exit. In this way
save CPU usage.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20230104194218.3785229-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for MDI-X status and configuration for KSZ9131 chips
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
FIELD_GET() must only be used with a mask that is a compile-time
constant. Mark the functions as __always_inline to avoid the problem.
Fixes: 21b688dabecb6a ("net: phy: micrel: Cable Diag feature for lan8814 phy")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Link: https://lore.kernel.org/r/20221011095437.12580-1-Divya.Koppera@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Config_intr and handle_interrupt are enabled for ksz9477 phy. It is
similar to all other phys in the micrel phys.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Inside the function lan8814_config_intr, there are double spaces when
assigning the return value of phy_write to err.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220921065444.637067-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit ece19502834d ("net: phy: micrel: 1588 support for LAN8814
phy") the handler always returns IRQ_HANDLED, except in an error case.
Before that commit, the interrupt status register was checked and if
it was empty, IRQ_NONE was returned. Restore that behavior to play nice
with the interrupt line being shared with others.
Fixes: ece19502834d ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Divya Koppera <Divya.Koppera@microchip.com>
Link: https://lore.kernel.org/r/20220920141619.808117-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for interrupts for LAN8804 PHY.
Tested-by: Michael Walle <michael@walle.cc> # on kontron-kswitch-d10
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220913142926.816746-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same GPIO line can be shared by multiple phys for the coma mode pin.
If that is the case then, all the other phys that share the same line
will failed to be probed because the access to the gpio line is not
non-exclusive.
Fix this by making access to the gpio line to be nonexclusive using flag
GPIOD_FLAGS_BIT_NONEXCLUSIVE. This allows all the other PHYs to be
probed.
Fixes: 738871b09250ee ("net: phy: micrel: add coma mode GPIO")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220830064055.2340403-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LED support for extended mode where
LED 1: Enhanced Mode 5 (10M/1000M/Activity)
LED 2: Enhanced Mode 4 (100M/1000M/Activity)
By default it supports KSZ9031 LED mode
Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that it is possible to use .probe without having .driver_data, let
KSZ8061 use the kszphy specific hooks for probe,suspend and resume,
which is preferred.
Switch to using the dedicated kszphy probe/suspend/resume functions.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220513114613.762810-2-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, if the .probe element is present in the phy_driver structure
and the .driver_data is not, a NULL pointer dereference happens.
Allow passing .probe without .driver_data by inserting NULL checks
for priv->type.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220513114613.762810-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
No conflicts.
Build issue in drivers/net/ethernet/sfc/ptp.c
54fccfdd7c66 ("sfc: efx_default_channel_type APIs can be static")
49e6123c65da ("net: sfc: fix memory leak due to ptp channel")
https://lore.kernel.org/all/20220510130556.52598fe2@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In lanphy_read_page_reg, calling __phy_read() might return a negative
error code. Use 'int' to check the error code.
Fixes: 7c2dcfa295b1 ("net: phy: micrel: Add support for LAN8804 PHY")
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220509144519.2343399-1-wanjiabing@vivo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit f1131b9c23fb ("net: phy: micrel: use
kszphy_suspend()/kszphy_resume for irq aware devices") the kszphy_suspend/
resume hooks are used.
These functions require the probe function to be called so that
priv can be allocated.
Otherwise, a NULL pointer dereference happens inside
kszphy_config_reset().
Cc: stable@vger.kernel.org
Fixes: f1131b9c23fb ("net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220504143104.1286960-2-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit f1131b9c23fb ("net: phy: micrel: use
kszphy_suspend()/kszphy_resume for irq aware devices") the following
NULL pointer dereference is observed on a board with KSZ8061:
# udhcpc -i eth0
udhcpc: started, v1.35.0
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = f73cef4e
[00000008] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 196 Comm: ifconfig Not tainted 5.15.37-dirty #94
Hardware name: Freescale i.MX6 SoloX (Device Tree)
PC is at kszphy_config_reset+0x10/0x114
LR is at kszphy_resume+0x24/0x64
...
The KSZ8061 phy_driver structure does not have the .probe/..driver_data
fields, which means that priv is not allocated.
This causes the NULL pointer dereference inside kszphy_config_reset().
Fix the problem by using the generic suspend/resume functions as before.
Another alternative would be to provide the .probe and .driver_data
information into the structure, but to be on the safe side, let's
just restore Ethernet functionality by using the generic suspend/resume.
Cc: stable@vger.kernel.org
Fixes: f1131b9c23fb ("net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220504143104.1286960-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The LAN8814 has a coma mode pin which puts the PHY into isolate and
power-dowm mode. Unfortunately, the mode cannot be disabled by a
register. Usually, the input pin has a pull-up and connected to a GPIO
which can then be used to disable the mode. Try to get the GPIO and
deassert it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Both lan8814_ptp_init() and lan8814_ptp_probe_once() are only used if
PTP and PHY timestamping is enabed. Up until now the probe function just
returns early, if they are not needed. But we need the
phy_package_init_once() functionality for the coma mode GPIO setup. Move
the check into the functions itself.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add cable test support for Micrel KSZ9x31 PHYs.
Tested on i.MX8M Mini with KSZ9131RNX in 100/Full mode with pairs shuffled
before magnetics:
(note: Cable test started/completed messages are omitted)
mx8mm-ksz9131-a-d-connected$ ethtool --cable-test eth0
Pair A code OK
Pair B code Short within Pair
Pair B, fault length: 0.80m
Pair C code Short within Pair
Pair C, fault length: 0.80m
Pair D code OK
mx8mm-ksz9131-a-b-connected$ ethtool --cable-test eth0
Pair A code OK
Pair B code OK
Pair C code Short within Pair
Pair C, fault length: 0.00m
Pair D code Short within Pair
Pair D, fault length: 0.00m
Tested on R8A77951 Salvator-XS with KSZ9031RNX and all four pairs connected:
(note: Cable test started/completed messages are omitted)
r8a7795-ksz9031-all-connected$ ethtool --cable-test eth0
Pair A code OK
Pair B code OK
Pair C code OK
Pair D code OK
The CTRL1000 CTL1000_ENABLE_MASTER and CTL1000_AS_MASTER bits are not
restored by calling phy_init_hw(), they must be manually cached in
ksz9x31_cable_test_start() and restored at the end of
ksz9x31_cable_test_get_status().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Oleksij Rempel <linux@rempel-privat.de>
Cc: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220407105534.85833-1-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the PHY and the MAC are capable of doing timestamping, the PHY has
priority. Therefore the DT option lan8814,ignore-ts was added such that
the PHY will not expose a PHC so then the timestamping was done in the
MAC. This is not the correct approach of doing it, therefore remove
this.
Fixes: ece19502834d84 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on the discussions here[1], the PHY driver is the wrong place
to set the latencies, therefore remove them.
[1] https://lkml.org/lkml/2022/3/4/325
Fixes: ece19502834d84 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan8814_match_rx_ts() invokes netif_rx() with disables interrupts
outside which will create a warning. Invoking netif_rx_ni() with
disabled interrupts is wrong even without the recent rework because
netif_rx_ni() would enable interrupts while processing the softirq. This
in turn can lead to dead lock if an interrupts triggers and attempts to
acquire kszphy_ptp_priv::rx_ts_lock.
Move netif_rx() outside the IRQ-off section.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
baebdf48c3600 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use generic ptp_msg_is_sync() function to avoid code duplication.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 1588 in LAN8814 phy driver.
It supports 1-step and 2-step timestamping.
Co-developed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make Extended page register accessing atomic,
to overcome unexpected output from register
reads/writes.
Fixes: 7c2dcfa295b1 ("net: phy: micrel: Add support for LAN8804 PHY")
Signed-off-by: Divya Koppera<Divya.Koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a setup with KSZ9131 and MACB drivers it happens on suspend path, from
time to time, that the PHY interrupt arrives after PHY and MACB were
suspended (PHY via genphy_suspend(), MACB via macb_suspend()). In this
case the phy_read() at the beginning of kszphy_handle_interrupt() will
fail (as MACB driver is suspended at this time) leading to phy_error()
being called and a stack trace being displayed on console. To solve this
.suspend/.resume functions for all KSZ devices implementing
.handle_interrupt were replaced with kszphy_suspend()/kszphy_resume()
which disable/enable interrupt before/after calling
genphy_suspend()/genphy_resume().
The fix has been adapted for all KSZ devices which implements
.handle_interrupt but it has been tested only on KSZ9131.
Fixes: 59ca4e58b917 ("net: phy: micrel: implement generic .handle_interrupt() callback")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add config_init for LAN8814. This function is required for the following
reasons:
- we need to make sure that the PHY is reset,
- disable ANEG with QSGMII PCS Host side
- swap the MDI-X A,B transmit so that there will not be any link flip-flaps
when the PHY gets a link.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for Link up or Link down
interrupt support in LAN8814 Quad phy
Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211221112217.9502-1-Divya.Koppera@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using
the power down mode bit (0.11). If the PHY is taken out of power down
mode in a certain temperature range, the PHY enters a weird state which
leads to continuously reporting RX errors. In that state, the MAC is not
able to receive or send any Ethernet frames and the activity LED is
constantly blinking. Since Linux is using the suspend callback when the
interface is taken down, ending up in that state can easily happen
during a normal startup.
Micrel confirmed the issue in errata DS80000700A [*], caused by abnormal
clock recovery when using power down mode. Even the latest revision (A4,
Revision ID 0x1513) seems to suffer that problem, and according to the
errata is not going to be fixed.
Remove the suspend/resume callback to avoid using the power down mode
completely.
[*] https://ww1.microchip.com/downloads/en/DeviceDoc/80000700A.pdf
Fixes: 1a5465f5d6a2 ("phy/micrel: Add suspend/resume support to Micrel PHYs")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems reasonable to fine-tune only some of the skew values when using
one of the rgmii-*id PHY modes, and even when all skew values are
specified, using the correct ID PHY mode makes sense for documentation
purposes. Such a configuration also appears in the binding docs in
Documentation/devicetree/bindings/net/micrel-ksz90x1.txt, so the driver
should not warn about it.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211012103402.21438-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Micrel KSZ9131 PHY LED behavior is not correct when configured in
Individual Mode, LED1 (Activity LED) is in the ON state when there is
no-link.
Workaround this by setting bit 9 of register 0x1e after verifying that
the LED configuration is Individual Mode.
This issue is described in KSZ9131RNX Silicon Errata DS80000693B [*]
and according to that it will not be corrected in a future silicon
revision.
[*] https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ9131RNX-Silicon-Errata-and-Data-Sheet-Clarification-80000863B.pdf
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN8804 PHY has same features as that of LAN8814 PHY except that it
doesn't support 1588, SyncE or Q-USGMII.
This PHY is found inside the LAN966X switches.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a5e63c7d38d5 "net: phy: micrel: Fix detection of ksz87xx
switch" broke link detection on the external ports of the KSZ8795.
The previously unused phy_driver structure for these devices specifies
config_aneg and read_status functions that appear to be designed for a
fixed link and do not work with the embedded PHYs in the KSZ8795.
Delete the use of these functions in favour of the generic PHY
implementations which were used previously.
Fixes: a5e63c7d38d5 ("net: phy: micrel: Fix detection of ksz87xx switch")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic for discerning between KSZ8051 and KSZ87XX PHYs is incorrect
such that the that KSZ87XX switch is not identified correctly.
ksz8051_ksz8795_match_phy_device() uses the parameter ksz_phy_id
to discriminate whether it was called from ksz8051_match_phy_device()
or from ksz8795_match_phy_device() but since PHY_ID_KSZ87XX is the
same value as PHY_ID_KSZ8051, this doesn't work.
Instead use a bool to discriminate the caller.
Without this patch, the KSZ8795 switch port identifies as:
ksz8795-switch spi3.1 ade1 (uninitialized): PHY [dsa-0.1:03] driver [Generic PHY]
With the patch, it identifies correctly:
ksz8795-switch spi3.1 ade1 (uninitialized): PHY [dsa-0.1:03] driver [Micrel KSZ87XX Switch]
Fixes: 8b95599c55ed24b36cf4 ("net: phy: micrel: Discern KSZ8051 and KSZ8795 PHYs")
Signed-off-by: Steve Bennett <steveb@workware.net.au>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch support for cable test for the ksz886x switches and the
ksz8081 PHY.
The patch was tested on a KSZ8873RLL switch with following results:
- port 1:
- provides invalid values, thus return -ENOTSUPP
(Errata: DS80000830A: "LinkMD does not work on Port 1",
http://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8873-Errata-DS80000830A.pdf)
- port 2:
- can detect distance
- can detect open on each wire of pair A (wire 1 and 2)
- can detect open only on one wire of pair B (only wire 3)
- can detect short between wires of a pair (wires 1 + 2 or 3 + 6)
- short between pairs is detected as open.
For example short between wires 2 + 3 is detected as open.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for MDI-X status and configuration
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for MDI-X status and configuration
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the alignments to one space between "#define" and the
macro.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer of_node is being initialized with a value that is never
read and it is being updated later with a new value inside a do-while
loop. The initialization is redundant and can be removed and the
pointer dev is no longer required and can be removed too.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following a similar reinstate for the KSZ9031.
Older kernels would use the genphy_soft_reset if the PHY did not implement
a .soft_reset.
Bluntly removing that default may expose a lot of situations where various
PHYs/board implementations won't recover on various changes.
Like with this implementation during a 4.9.x to 5.4.x LTS transition.
I think it's a good thing to remove unwanted soft resets but wonder if it
did open a can of worms?
Atleast this fixes one iMX6 FEC/RMII/8081 combo.
Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Christian Melki <christian.melki@t2data.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210224205536.9349-1-christian.melki@t2data.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
