IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
In ksz9477.c file, configuring the xmii register is performed based on
the flag NEW_XMII. The flag is reset for ksz9893 switch and set for
other switch. This patch uses the ksz common xmii set and get function.
The bit values are configured based on the chip id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch read the rgmii tx and rx delay from device tree and stored it
in the ksz_port. It applies the rgmii delay to the xmii tune adjust
register based on the interface selected in phylink mac config. There
are two rgmii port in LAN937x and value to be loaded in the register
vary depends on the port selected.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the common ksz_set_xmii function for ksz series switch
and update the lan937x code phylink mac config. The register address for
the ksz8795 is Port 5 Interface control 6 and for all other switch is
xMII Control 1.
The bit value for selecting the interface is same for
KSZ8795 and KSZ9893 are same. The bit values for KSZ9477 and lan973x are
same. So, this patch add the bit value for each switches in
ksz_chip_data and configure the registers based on the chip id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the support for common phylink mac link up for the ksz
series switch. The register address, bit position and values are
configured based on the chip id to the dev->info structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add common function for configuring the Full/Half duplex and
transmit/receive flow control. KSZ8795 uses the Global control register
4 for configuring the duplex and flow control, whereas all other KSZ9477
based switch uses the xMII Control 0 register.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the function for configuring the 100/10Mbps speed
selection for the ksz switches. KSZ8795 switch uses Global control 4
register 0x06 bit 4 for choosing 100/10Mpbs. Other switches uses xMII
control 1 0xN300 for it.
For KSZ8795, if the bit is set then 10Mbps is chosen and if bit is
clear then 100Mbps chosen. For all other switches it is other way
around, if the bit is set then 100Mbps is chosen.
So, this patch add the generic function for ksz switch to select the
100/10Mbps speed selection. While configuring, first it disables the
gigabit functionality and then configure the respective speed.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add helper function for setting and getting the gigabit
enable for the ksz series switch. KSZ8795 switch has different register
address compared to all other ksz switches. KSZ8795 series uses the Port
5 Interface control 6 Bit 6 for configuring the 1Gbps or 100/10Mbps
speed selection. All other switches uses the xMII control 1 0xN301
register Bit6 for gigabit.
Further, for KSZ8795 & KSZ9893 switches if bit 1 then 1Gbps is chosen
and if bit 0 then 100/10Mbps is chosen. It is other way around for
other switches bit 0 is for 1Gbps. So, this patch implements the common
function for configuring the gigabit set and get capability.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the refactoring for the ksz8_dev_ops from ksz8795.c to
ksz_common.c, the ksz8_r_mib_cnt has been missed. So this patch adds the
missing one.
Fixes: 6ec23aaaac43 ("net: dsa: microchip: move ksz_dev_ops to ksz_common.c")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220718061803.4939-1-arun.ramadoss@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add spi_device_id entries to silent SPI warnings.
Fixes: 5fa6863ba692 ("spi: Check we have a spi_device_id for each DT compatible")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220717135831.2492844-2-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add spi_device_id entries to silent following warnings:
SPI driver sja1105 has no spi_device_id for nxp,sja1105e
SPI driver sja1105 has no spi_device_id for nxp,sja1105t
SPI driver sja1105 has no spi_device_id for nxp,sja1105p
SPI driver sja1105 has no spi_device_id for nxp,sja1105q
SPI driver sja1105 has no spi_device_id for nxp,sja1105r
SPI driver sja1105 has no spi_device_id for nxp,sja1105s
SPI driver sja1105 has no spi_device_id for nxp,sja1110a
SPI driver sja1105 has no spi_device_id for nxp,sja1110b
SPI driver sja1105 has no spi_device_id for nxp,sja1110c
SPI driver sja1105 has no spi_device_id for nxp,sja1110d
Fixes: 5fa6863ba692 ("spi: Check we have a spi_device_id for each DT compatible")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220717135831.2492844-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch removes the of_match_ptr() pointer when dereferencing the
ksz_dt_ids which produce the unused variable warning.
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ksz_switch_register(), we should call of_node_put() for the
reference returned by of_get_child_by_name() which has increased
the refcount.
Fixes: 912aae27c6af ("net: dsa: microchip: really look for phy-mode in port nodes")
Signed-off-by: Liang He <windhl@126.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220714153138.375919-1-windhl@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move qca8k driver to qca dir in preparation for code split and
introduction of ipq4019 switch based on qca8k.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary spi_set_drvdata() in b53_spi_remove(), the
driver_data will be set to NULL in device_unbind_cleanup() after
calling ->remove().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220705131733.351962-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
felix_vsc9959.c calls taprio_offload_get() and taprio_offload_free(),
symbols exported by net/sched/sch_taprio.c. As such, we must disallow
building the Felix driver as built-in when the symbol exported by
tc-taprio isn't present in the kernel image.
Fixes: 1c9017e44af2 ("net: dsa: felix: keep reference on entire tc-taprio config")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220704190241.1288847-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch add the LAN937x part support in the existing ksz_spi_probe.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for phylink_mac_config dsa hook. It configures
the mac for MII/RMII modes. The RGMII mode will be added in the future
patches.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for phylink_mac_link_up. It configures the mac
for the speed, flow control and duplex mode.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal phy of the LAN937x are capable of 100Mbps Full duplex. The
xMII port of switch is capable of 10Mbps Full & Half Duplex, 100Mbps
Full & Half Duplex and 1000Mbps Half duplex. xMII port also supports Tx
and Rx Flow control.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the support for port_max_mtu, port_change_mtu and
port_fast_age dsa functionality.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch register mdio-bus for the lan937x series switch. mdio read
and write uses the vphy for accessing the phy register.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for the writing and reading of the phy registers.
LAN937x uses the Vphy indirect addressing method for accessing the phys.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch update the ksz_get_tag_protocol to return LAN937x specific
tag if the chip id matches one of LAN937x series switch
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basic DSA driver support for lan937x and the device will be
configured through SPI interface.
It adds the lan937x_dev_ops in ksz_common.c file and tries to reuse the
functionality of ksz9477 series switch.
drivers/net/dsa/microchip/ path is already part of MAINTAINERS &
the new files come under this path. Hence no update needed to the
MAINTAINERS
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ksz9477 and lan937x has few difference in the static and reserved
table register 0x041C. For the ksz9477 if the bit 0 is 1 - read
operation and 0 - write operation. But for lan937x bit 1:0 used for
selecting the read/write operation, 01 - write and 10 - read.
To use ksz9477 mdb add/del and enable_stp_addr for the lan937x, masks &
shifts are introduced for ksz9477 & lan937x in ksz_common.c. Then
updated the function with masks & shifts based on the switch instead of
hard coding it.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Time-sensitive networking code needs to work with PTP times expressed in
nanoseconds, and with packet transmission times expressed in
picoseconds, since those would be fractional at higher than gigabit
speed when expressed in nanoseconds.
Convert the existing uses in tc-taprio and the ocelot/felix DSA driver
to a PSEC_PER_NSEC macro. This macro is placed in include/linux/time64.h
as opposed to its relatives (PSEC_PER_SEC etc) from include/vdso/time64.h
because the vDSO library does not (yet) need/use it.
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com> # for the vDSO parts
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, sending a packet into a time gate too small for it (or always
closed) causes the queue system to hold the frame forever. Even worse,
this frame isn't subject to aging either, because for that to happen, it
needs to be scheduled for transmission in the first place. But the frame
will consume buffer memory and frame references while it is forever held
in the queue system.
Before commit a4ae997adcbd ("net: mscc: ocelot: initialize watermarks to
sane defaults"), this behavior was somewhat subtle, as the switch had a
more intricately tuned default watermark configuration out of reset,
which did not allow any single port and tc to consume the entire switch
buffer space. Nonetheless, the held frames are still there, and they
reduce the total backplane capacity of the switch.
However, after the aforementioned commit, the behavior can be very
clearly seen, since we deliberately allow each {port, tc} to consume the
entire shared buffer of the switch minus the reservations (and we
disable all reservations by default). That is to say, we allow a
permanently closed tc-taprio gate to hang the entire switch.
A careful inspection of the documentation shows that the QSYS:Q_MAX_SDU
per-port-tc registers serve 2 purposes: one is for guard band calculation
(when zero, this falls back to QSYS:PORT_MAX_SDU), and the other is to
enable oversized frame dropping (when non-zero).
Currently the QSYS:Q_MAX_SDU registers are all zero, so oversized frame
dropping is disabled. The goal of the change is to enable it seamlessly.
For that, we need to hook into the MTU change, tc-taprio change, and
port link speed change procedures, since we depend on these variables.
Frames are not dropped on egress due to a queue system oversize
condition, instead that egress port is simply excluded from the mask of
valid destination ports for the packet. If there are no destination
ports at all, the ingress counter that increments is the generic
"drop_tail" in ethtool -S.
The issue exists in various forms since the tc-taprio offload was introduced.
Fixes: de143c0e274b ("net: dsa: felix: Configure Time-Aware Scheduler via taprio offload")
Reported-by: Richie Pearn <richard.pearn@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In vsc9959_tas_clock_adjust(), the INIT_GATE_STATE field is not changed,
only the ENABLE field. Similarly for the disabling of the time-aware
shaper in vsc9959_qos_port_tas_set().
To reflect this, keep the QSYS_TAG_CONFIG_INIT_GATE_STATE_M mask out of
the read-modify-write procedure to make it clearer what is the intention
of the code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future change we will need to remember the entire tc-taprio config
on all ports rather than just the base time, so use the
taprio_offload_get() helper function to replace ocelot_port->base_time
with ocelot_port->taprio.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
of_parse_phandle() will increase the refcount of 'pcs_node', so add
of_node_put() before return from a5psw_pcs_get().
Fixes: 888cdb892b61 ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220630014153.1888811-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/ethernet/microchip/sparx5/sparx5_switchdev.c
9c5de246c1db ("net: sparx5: mdb add/del handle non-sparx5 devices")
fbb89d02e33a ("net: sparx5: Allow mdb entries to both CPU and ports")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Both PSFP stats and the port stats read by ocelot_check_stats_work() are
indirectly read through the same mechanism - write to STAT_CFG:STAT_VIEW,
read from SYS:STAT:CNT[n].
It's just that for port stats, we write STAT_VIEW with the index of the
port, and for PSFP stats, we write STAT_VIEW with the filter index.
So if we allow them to run concurrently, ocelot_check_stats_work() may
change the view from vsc9959_psfp_counters_get(), and vice versa.
Fixes: 7d4b564d6add ("net: dsa: felix: support psfp filter on vsc9959")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220629183007.3808130-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The devm_platform_ioremap_resource() function never returns NULL.
It returns error pointers.
Signed-off-by: Peng Wu <wupeng58@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Clément Léger <clement.leger@bootlin.com>
Link: https://lore.kernel.org/r/20220628130920.49493-1-wupeng58@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This switch is calculating tx/rx_bytes for all packets including pause.
So, include rx/tx_pause counter to rx/tx_packets to make tx/rx_bytes fit
to rx/tx_packets.
Link: https://lore.kernel.org/all/20220624220317.ckhx6z7cmzegvoqi@skbuf/
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for pause specific stats.
Tested on ksz9477.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch moves the broadcast ctrl, multicast ctrl and start control
registers from ksz_chip_dat to ksz_chip_reg.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the stp_ctrl_reg from the ksz_chip_data to ksz_chip_reg
structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register size for the ksz8 switches is u8 and for ksz9477 series is
u16. To have common struct for ksz series switches the size of reg is
increased from u8 to u16.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the struct ksz8 from ksz8.h which is no longer
needed. The platform bus specific details are now deferenced through
dev->priv.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves ksz8->shifts from ksz8795.c to ksz_common.c. The shifts
are dereferenced using dev->info->shifts.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the ksz8->masks from ksz8795.c to ksz_common.c. The
mask will be dereferenced using dev->info->masks.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the ksz8->regs from ksz8795.c to the ksz_common.c. And
the regs is dereferrenced using dev->info->regs.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commits add forwarding database support to the driver. It
implements fdb_add(), fdb_del() and fdb_dump().
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add statistics support to the rzn1-a5psw driver by implementing the
following dsa_switch_ops callbacks:
- get_sset_count()
- get_strings()
- get_ethtool_stats()
- get_eth_mac_stats()
- get_eth_ctrl_stats()
- get_rmon_stats()
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Renesas RZ/N1 advanced 5 port switch driver. This switch handles 5
ports including 1 CPU management port. A MDIO bus is also exposed by
this switch and allows to communicate with PHYs connected to the ports.
Each switch port (except for the CPU management ports) is connected to
the MII converter.
This driver includes basic bridging support, more support will be added
later (vlan, etc).
Suggested-by: Jean-Pierre Geslin <jean-pierre.geslin@non.se.com>
Suggested-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of now, there are two spi probes, one ksz8795_spi.c and other
ksz9477_spi.c. This patch combines two files into single ksz_spi.c. The
difference between the two are regmap config and struct ksz8. The regmap
config is assigned based on the platform data. And struct ksz8 is left
untouched, as it is used only ksz8795.c. It can be used for all
other switches also in future.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch delete the ksz8_switch_register and ksz9477_switch_register
since both are calling the ksz_switch_register function. Instead the
ksz_switch_register is called from the probe function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
