IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Currently, the GPIO interface is said to Open Drain if it is Single
Ended and active LOW. Similarly, it is said as Open Source if it is
Single Ended and active HIGH.
The active HIGH/LOW is used in the interface for setting the pin
state to HIGH or LOW when enabling/disabling the interface.
In Open Drain interface, pin is set to HIGH by putting pin in
high impedance and LOW by driving to the LOW.
In Open Source interface, pin is set to HIGH by driving pin to
HIGH and set to LOW by putting pin in high impedance.
With above, the Open Drain/Source is unrelated to the active LOW/HIGH
in interface. There is interface where the enable/disable of interface
is ether active LOW or HIGH but it is Open Drain type.
Hence decouple the Open Drain with Single Ended + Active LOW and
Open Source with Single Ended + Active HIGH.
Adding different flag for the Open Drain/Open Source which is valid
only when Single ended flag is enabled.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the Amlogic Meson GXL SoC, this is a partially complete
definition only based on the Amlogic Vendor tree.
This definition differs a lot from the GXBB and needs a separate entry.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Add the devm_pinctrl_register() API and switch all applicable drivers
to use it, saving lots of lines of code all over the place.
New drivers:
- New driver for the Broadcom NS2 SoC.
- New subdriver for the PXA25x SoCs.
- New subdriver for the AMLogic Meson GXBB SoC.
Driver improvements:
- The Intel Baytrail driver now properly supports pin control.
- The Nomadik, Rockchip, Broadcom BCM2835 supports the .get_direction() callback in
the GPIO portions.
- Continued development and stabilization of several SH-PFC
SoC subdrivers: r8a7795, r8a7790, r8a7794 etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tlvn
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This kernel cycle was quite calm when it comes to pin control and
there is really just one major change, and that is the introduction of
devm_pinctrl_register() managed resources.
Apart from that linear development, details below.
Core changes:
- Add the devm_pinctrl_register() API and switch all applicable
drivers to use it, saving lots of lines of code all over the place.
New drivers:
- driver for the Broadcom NS2 SoC
- subdriver for the PXA25x SoCs
- subdriver for the AMLogic Meson GXBB SoC
Driver improvements:
- the Intel Baytrail driver now properly supports pin control
- Nomadik, Rockchip, Broadcom BCM2835 support the .get_direction()
callback in the GPIO portions
- continued development and stabilization of several SH-PFC SoC
subdrivers: r8a7795, r8a7790, r8a7794 etc"
* tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (85 commits)
Revert "pinctrl: tegra: avoid parked_reg and parked_bank"
pinctrl: meson: Fix eth_tx_en bit index
pinctrl: tegra: avoid parked_reg and parked_bank
pinctrl: tegra: Correctly check the supported configuration
pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC
pinctrl: rockchip: fix pull setting error for rk3399
pinctrl: stm32: Implement .pin_config_dbg_show()
pinctrl: nomadik: hide nmk_gpio_get_mode when unused
pinctrl: ns2: rename pinctrl_utils_dt_free_map
pinctrl: at91: Merge clk_prepare and clk_enable into clk_prepare_enable
pinctrl: at91: Make at91_gpio_template const
pinctrl: baytrail: fix some error handling in debugfs
pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC
pinctrl: sirf/atlas7: trivial fix of spelling mistake on flagged
pinctrl: sh-pfc: Kill unused variable in sh_pfc_remove()
pinctrl: nomadik: implement .get_direction()
pinctrl: nomadik: use BIT() with offsets consequently
pinctrl: exynos5440: Use off-stack memory for pinctrl_gpio_range
pinctrl: zynq: Use devm_pinctrl_register() for pinctrl registration
pinctrl: u300: Use devm_pinctrl_register() for pinctrl registration
...
This patch adds the basic platform file to support the pin controller
found on the Amlogic Meson GXBB SoCs.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra186 contains two separate but mostly similar GPIO controllers.
Register layout differs significantly from previous Tegra generations,
and so a new binding is required to describe them in device tree. This
patch adds that binding.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to the Tegra TRM, GPIOs are aggregated into /ports/ of 8 GPIOs,
not into /banks/. Fix <dt-bindings/gpio/tegra-gpio.h> to correctly reflect
this naming convention. While this seems like silly churn, it will become
slightly more important once we introduce the GPIO binding for upcoming
Tegra chips.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
It is customary for GPIO controllers to support open drain/collector
and open source/emitter configurations. Add standard GPIO line flags
to account for this and augment the documentation to say that these
are the most generic bindings.
Several people approached me to add new flags to the lines, and this
makes sense, but let's first bind up the most common cases before we
start to add exotic stuff.
Thanks to H. Nikolaus Schaller for ideas on how to encode single-ended
wiring such as open drain/source and open collector/emitter.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for the AmLogic Meson8b SoC.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a driver for the pinmux and GPIO controller available in
Amlogic Meson SoCs. It currently supports only Meson8, however the
common code should be generic enough to work also for other SoCs after
having defined the proper set of functions and groups.
GPIO interrupts are not supported at the moment due to lack of
documentation.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
NVIDIA Tegra124 supports has the new GPIO port as GPIO_FF.
Add the macro for this port name.
Signed-off-by: Ashwini Ghuge <aghuge@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
All Tegra GPIOs are named after the GPIO bank and GPIO number within
the bank. Define a macro to calculate the GPIO ID based on those
parameters. Make the macro available via all Tegra .dtsip files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Many GPIO device tree bindings use the same flags. Create a header to
define those.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
