IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This adds a few small quirks to handle the differences between
the STM32 and Ux500 cryp blocks. The following differences
are handled with special bool switch bits in the capabilities:
- The main difference is that some registers are removed, so we
add register offsets for all registers in the
per-variant data. Then we assign the right offsets for Ux500
vs the STM32 variants.
- The Ux500 does not support the aeads algorithms; gcm(aes)
and ccm(aes). Avoid registering them when running on Ux500.
- The Ux500 has a special "linear" key format and does some
elaborare bit swizzling of the key bits before writing them
into the key registers. This is written as an "application
note" inside the DB8500 design specification, and seems to
be the result of some mishap when assigning the data lines
to register bits. (STM32 has clearly fixed this.)
- The Ux500 does not have the KP "key prepare" bit in the
CR register. Instead, we need to set the KSE bit,
"key schedule encryption" bit which does the same thing
but is in bit 11 rather than being a special "algorithm
type" as on STM32. The algorithm must however be specified
as AES ECB while doing this.
- The Ux500 cannot just read out IV registers, we need to
set the KEYRDEN "key read enable" bit, as this protects
not just the key but also the IV from being read out.
Enable this bit before reading out the IV and disable it
afterwards.
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked by: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Ux500 cryp and hash drivers are older versions of the
hardware managed by the stm32 driver.
Instead of trying to improve the Ux500 cryp and hash drivers,
start to switch over to the modern and more well-maintained
STM32 drivers.
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch fixes the sparse warning about arrays of flexible
structures by removing an unnecessary use of them in struct
__crypto_ctx.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The acomp API allows to send requests with a NULL destination buffer. In
this case, the algorithm implementation needs to allocate the
destination scatter list, perform the operation and return the buffer to
the user. For decompression, data is likely to expand and be bigger than
the allocated buffer.
This implements a re-submission mechanism for decompression requests
that is triggered if the destination buffer, allocated by the driver,
is not sufficiently big to store the output from decompression.
If an overflow is detected when processing the callback for a
decompression request with a NULL destination buffer, a workqueue is
scheduled. This allocates a new scatter list of size CRYPTO_ACOMP_DST_MAX,
now 128KB, creates a new firmware scatter list and resubmits the job to
the hardware accelerator.
Suggested-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Enable deflate for QAT GEN4 devices.
This adds
(1) logic to create configuration entries at probe time for the
compression instances for QAT GEN4 devices;
(2) the implementation of QAT GEN4 specific compression operations,
required since the creation of the compression request template is
different between GEN2 and GEN4; and
(3) updates to the firmware API related to compression for GEN4.
The implementation configures the device to produce data compressed
dynamically, optimized for throughput over compression ratio.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add infrastructure for implementing the acomp APIs in the QAT driver and
expose the deflate algorithm for QAT GEN2 devices.
This adds
(1) the compression service which includes logic to create, allocate
and handle compression instances;
(2) logic to create configuration entries at probe time for the
compression instances;
(3) updates to the firmware API for allowing the compression service;
and;
(4) a back-end for deflate that implements the acomp api for QAT GEN2
devices.
The implementation configures the device to produce data compressed
statically, optimized for throughput over compression ratio.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Rename qat_crypto_dev_config() in adf_gen2_dev_config() and relocate it
to the newly created file adf_gen2_config.c.
This function is specific to QAT GEN2 devices and will be used also to
configure the compression service.
In addition change the drivers to use the dev_config() in the hardware
data structure (which for GEN2 devices now points to
adf_gen2_dev_config()), for consistency.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move qat_algs_alloc_flags() from qat_crypto.h to qat_bl.h as this will
be used also by the compression logic.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move the structures qat_instance_backlog and qat_alg_req from
qat_crypto.h to qat_algs_send.h since they are not unique to crypto.
Both structures will be used by the compression service to support
requests with the CRYPTO_TFM_REQ_MAY_BACKLOG flag set.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The compression service requires an additional pre-allocated buffer for
each destination scatter list.
Extend the function qat_alg_sgl_to_bufl() to take an additional
structure that contains the dma address and the size of the extra
buffer which will be appended in the destination FW SGL.
The logic that unmaps buffers in qat_alg_free_bufl() has been changed to
start unmapping from buffer 0 instead of skipping the initial buffers
num_buff - num_mapped_bufs as that functionality was not used in the
code.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The structure qat_crypto_request_buffs which contains the source and
destination buffer lists and correspondent sizes and dma addresses is
also required for the compression service.
Rename it as qat_request_buffs and move it to qat_bl.h.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The functions qat_alg_sgl_to_bufl() and qat_alg_free_bufl() take as
argument a qat_crypto_instance and a qat_crypto_request structure.
These two structures are used only to get a reference to the
adf_accel_dev and qat_crypto_request_buffs.
In order to reuse these functions for the compression service, change
the signature so that they take adf_accel_dev and
qat_crypto_request_buffs.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Rename the functions qat_alg_sgl_to_bufl() and qat_alg_free_bufl() as
qat_bl_sgl_to_bufl() and qat_bl_free_bufl() after their relocation into
the qat_bl module.
This commit does not implement any functional change.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move the logic that maps, unmaps and converts scatterlists into QAT
bufferlists from qat_algs.c to a new module, qat_bl.
This is to allow reuse of the logic by the data compression service.
This commit does not implement any functional change.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com>
Reviewed-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit d2825fa936 ("crypto: sm3,sm4 - move into crypto directory") moves
the SM3 and SM4 stand-alone library and the algorithm implementation for
the Crypto API into the same directory, and the corresponding relationship
of Kconfig is modified, CONFIG_CRYPTO_SM3/4 corresponds to the stand-alone
library of SM3/4, and CONFIG_CRYPTO_SM3/4_GENERIC corresponds to the
algorithm implementation for the Crypto API. Therefore, it is necessary
for this module to depend on the correct algorithm.
Fixes: d2825fa936 ("crypto: sm3,sm4 - move into crypto directory")
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: stable@vger.kernel.org # v5.19+
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been implicitly relying on kmalloc alignment
to be sufficient for DMA. This may no longer be the case with
upcoming arm64 changes.
This patch changes it to explicitly request DMA alignment from
the Crypto API.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The helper crypto_tfm_ctx is only used by the Crypto API algorithm
code and should really be in algapi.h. However, for historical
reasons many files relied on it to be in crypto.h. This patch
changes those files to use algapi.h instead in prepartion for a
move.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
omap_sham_probe() calls pm_runtime_get_sync() and calls
pm_runtime_put_sync() latter to put usage_counter. However,
pm_runtime_get_sync() will increment usage_counter even it failed. Fix
it by replacing it with pm_runtime_resume_and_get() to keep usage
counter balanced.
Fixes: b359f034c8 ("crypto: omap-sham - Convert to use pm_runtime API")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is no real point in allocating dedicated memory for the irqs array.
MAXFLOW is only 2, so it is easier to allocated the needed space
directly within the 'meson_dev' structure.
This saves some memory allocation and avoids an indirection when using the
irqs array.
Fixes: 48fe583fe5 ("crypto: amlogic - Add crypto accelerator...")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The value of reqsize must only be changed through the helper.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The value of reqsize must only be changed through the helper.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The value of reqsize must only be changed through the helper.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The value of reqsize must only be changed through the helper.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If CAAM is not in "trusted" or "secure" state, a fixed non-volatile key
is used instead of the unique device key. This is the default mode of
operation without secure boot (HAB). In this scenario, CAAM encrypted
blobs should be used only for testing but not in a production
environment, so issue a warning.
Signed-off-by: Nikolaus Voss <nikolaus.voss@haag-streit.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix to return a negative error code -EINVAL instead of 0.
Fixes: 0cec19c761 ("crypto: qat - add support for compression for 4xxx")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Acked-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In function 'hisi_qm_resume', if the device fails to be started,
directly returning error code will cause the device to be unavailable.
However, the failure may be caused by device error, which will be
reported to the driver, and driver can reset and restart device.
Therefore, check device status instead of returning error code
directly. Returns 0 if device error has occurred, otherwise returns
error code.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
'QM_XEQ_DEPTH_CAP' mask value is GENMASK(31, 0) instead of GENMASK(15, 0).
If the mask value is incorrect, will cause abnormal events cannot be
handled. So fix it.
Fixes: 129a9f3401 ("crypto: hisilicon/qm - get qp num and depth from hardware registers")
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ccree_init() calls cc_debugfs_global_fini(), the former is an init
function and the latter an exit function though.
A modular build emits:
WARNING: modpost: drivers/crypto/ccree/ccree.o: section mismatch in reference: init_module (section: .init.text) -> cc_debugfs_global_fini (section: .exit.text)
(with CONFIG_DEBUG_SECTION_MISMATCH=y).
Fixes: 4f1c596df7 ("crypto: ccree - Remove debugfs when platform_driver_register failed")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix that put two or more continuous blank lines inside function.
Signed-off-by: Wenkai Lin <linwenkai6@hisilicon.com>
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There are a couple of spelling mistakes in sec2. Fix them.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reduce the function complexity by use the function table in the
process of dumping queue. The function input parameters are
unified. And maintainability is enhanced.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Considering that the qm feature and debugfs feature are independent.
The code related to debugfs is getting larger and larger. It should be
separate as a debugfs file. So move some debugfs code to new file from
qm file. The qm code logic is not modified. And maintainability is
enhanced.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The last register logic and different register logic are combined.
Use "u32" instead of 'int' in the regs function input parameter to
simplify some checks.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is no security data in the pointer. It is only a value transferred
as a structure. It makes no sense to zero a variable that is on the stack.
So not need to set the pointer to null.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When platform_driver_register failed, we need to remove debugfs,
which will caused a resource leak, fix it.
Failed logs as follows:
[ 32.606488] debugfs: Directory 'ccree' with parent '/' already present!
Fixes: 4c3f97276e ("crypto: ccree - introduce CryptoCell driver")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Most hw_random devices return entropy which is assumed to be of full
quality, but driver authors don't bother setting the quality knob. Some
hw_random devices return less than full quality entropy, and then driver
authors set the quality knob. Therefore, the entropy crediting should be
opt-out rather than opt-in per-driver, to reflect the actual reality on
the ground.
For example, the two Raspberry Pi RNG drivers produce full entropy
randomness, and both EDK2 and U-Boot's drivers for these treat them as
such. The result is that EFI then uses these numbers and passes the to
Linux, and Linux credits them as boot, thereby initializing the RNG.
Yet, in Linux, the quality knob was never set to anything, and so on the
chance that Linux is booted without EFI, nothing is ever credited.
That's annoying.
The same pattern appears to repeat itself throughout various drivers. In
fact, very very few drivers have bothered setting quality=1024.
Looking at the git history of existing drivers and corresponding mailing
list discussion, this conclusion tracks. There's been a decent amount of
discussion about drivers that set quality < 1024 -- somebody read and
interepreted a datasheet, or made some back of the envelope calculation
somehow. But there's been very little, if any, discussion about most
drivers where the quality is just set to 1024 or unset (or set to 1000
when the authors misunderstood the API and assumed it was base-10 rather
than base-2); in both cases the intent was fairly clear of, "this is a
hardware random device; it's fine."
So let's invert this logic. A hw_random struct's quality knob now
controls the maximum quality a driver can produce, or 0 to specify 1024.
Then, the module-wide switch called "default_quality" is changed to
represent the maximum quality of any driver. By default it's 1024, and
the quality of any particular driver is then given by:
min(default_quality, rng->quality ?: 1024);
This way, the user can still turn this off for weird reasons (and we can
replace whatever driver-specific disabling hacks existed in the past),
yet we get proper crediting for relevant RNGs.
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
