IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Enable power floor feature support for Meteor Lake processors.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On thermal device interrupt, if the interrupt is generated for passing
power floor status, call the callback to pass notification to the user
space.
First call proc_thermal_check_power_floor_intr() to check interrupt, if
this callback returns true, wake the IRQ thread to call
proc_thermal_power_floor_intr_callback() to notify user space.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When the hardware reduces the power to the minimum possible, the power
floor is notified via an interrupt.
This can happen when user space requests a power limit via powercap RAPL
interface, which forces the system to enter to the lowest power. This
power floor indication can be used as a hint to resort to other methods
of reducing power than via RAPL power limit.
Before power floor status can be read or the firmware can trigger
notifications regarding it, it needs to be configured via a mailbox
command. The actual power floor status is read via bit 39 of MMIO
offset 0x5B18 of the processor thermal PCI device.
To show the current power floor status and get notification
on a sysfs attribute, add 2 new attributes to
/sys/bus/pci/devices/0000\:00\:04.0/power_limits/
power_floor_enable : This attribute is present when power floor
notifications are supported. This attribute allows to enable/disable
power floor notifications.
power_floor_status : This attribute is present when power floor
notifications are supported. When enabled via power_floor_enable, this
attribute shows the current power floor status.
The power floor implementation provides interfaces which are called
from the sysfs callbacks to enable/disable and read power floor
status. It also provides two additional interfaces to check if the
current processor thermal device interrupt is for power floor status
and to send notifications to user space.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog and documentation changes edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The function proc_thermal_add() adds sysfs entries for power limits.
The feature mask of available features is not present at that time, so
it cannot be used by proc_thermal_add() to selectively create sysfs
attributes.
The feature mask is set by proc_thermal_mmio_add(), so modify the code
to call it before proc_thermal_add() so as to allow the latter to use
the feature mask.
There is no functional impact with this change.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The SOC interrupt status register contains multiple interrupt sources
(workload hint interrupt and power floor interrupt). It is not possible
to clear individual interrupt source with read-modify-write, as it may
clear the new interrupt from the firmware after a read operation. It is
also not possible to set the interrupt status bit to 1 for the other
interrupt source, which is not part of clearing.
Hence, create a common function, to clear all status bits at once.
Call this function after processing all interrupt sources.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move define SOC_WT_RES_INT_STATUS_OFFSET to processor_thermal_device.h.
This way it can be reused in other modules.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
KASAN reported this
[ 444.853098] BUG: KASAN: global-out-of-bounds in param_get_int+0x77/0x90
[ 444.853111] Read of size 4 at addr ffffffffc16c9220 by task cat/2105
...
[ 444.853442] The buggy address belongs to the variable:
[ 444.853443] max_idle+0x0/0xffffffffffffcde0 [intel_powerclamp]
There is a mismatch between the param_get_int and the definition of
max_idle. Replacing param_get_int with param_get_byte resolves this
issue.
Fixes: ebf519710218 ("thermal: intel: powerclamp: Add two module parameters")
Cc: 6.3+ <stable@vger.kernel.org> # 6.3+
Signed-off-by: David Arcari <darcari@redhat.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify int340x_thermal_update_trips() to use thermal_zone_for_each_trip()
for walking trips instead of using the trips[] table passed to the
thermal zone registration function.
For this purpose, store active trip point indices in the priv fieids of
the corresponding thermal_trip structures.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add a wrapper around for_each_thermal_trip(), called
thermal_zone_for_each_trip(), that will invoke the former under the
thermal zone lock and pass its return value to the caller.
Two drivers will be modified subsequently to use this new function.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add new helper functions, thermal_bind_cdev_to_trip() and
thermal_unbind_cdev_from_trip(), to allow a trip pointer to be used for
binding a cooling device to a trip point and unbinding it, respectively,
and redefine the existing helpers, thermal_zone_bind_cooling_device()
and thermal_zone_unbind_cooling_device(), as wrappers around the new
ones, respectively.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Replace the integer trip number stored in struct thermal_instance with
a pointer to the relevant trip and adjust the code using the structure
in question accordingly.
The main reason for making this change is to allow the trip point to
cooling device binding code more straightforward, as illustrated by
subsequent modifications of the ACPI thermal driver, but it also helps
to clarify the overall design and allows the governor code overhead to
be reduced (through subsequent modifications).
The only case in which it adds complexity is trip_point_show() that
needs to walk the trips[] table to find the index of the given trip
point, but this is not a critical path and the interface that
trip_point_show() belongs to is problematic anyway (for instance, it
doesn't cover the case when the same cooling devices is associated
with multiple trip points).
This is a preliminary change and the affected code will be refined by
a series of subsequent modifications of thermal governors, the core and
the ACPI thermal driver.
The general functionality is not expected to be affected by this change.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
It is invalid to call for_each_thermal_trip() on an unregistered thermal
zone anyway, and as per thermal_zone_device_register_with_trips(), the
trips[] table must be present if num_trips is greater than zero for the
given thermal zone.
Hence, the trips check in for_each_thermal_trip() is redundant and so it
can be dropped.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
After recent changes, thermal_zone_get_trip() cannot fail, as invoked
from thermal_zone_device_register_with_trips(), so the only role of
the trips_disabled bitmask is struct thermal_zone_device is to make
handle_thermal_trip() skip trip points whose temperature was initially
zero. However, since the unit of temperature in the thermal core is
millicelsius, zero may very well be a valid temperature value at least
in some usage scenarios and the trip temperature may as well change
later. Thus there is no reason to permanently disable trip points
with initial temperature equal to zero.
Accordingly, drop the trips_disabled bitmask along with the code
related to it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
All interrupts from the processor thermal PCI device require ACK. This
is done by writing 0x01 at offset 0xDC in the config space.
This is already done for the thereshold interrupt. Extend this for the
workload hint interrupt.
Fixes: e682b86211a1 ("thermal: int340x: Handle workload hint interrupts")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add ArrowLake-S PCI ID for processor thermal device.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit 2e38a2a981b2 ("thermal/core: Add a generic thermal_zone_set_trip()
function") updating a trip point temperature doesn't actually work,
because the value supplied by user space is subsequently overwritten
with the current trip point hysteresis value.
Fix this by changing the code to parse the number string supplied by
user space after retrieving the current trip point data from the
thermal zone.
Also drop a redundant tab character from the code in question.
Fixes: 2e38a2a981b2 ("thermal/core: Add a generic thermal_zone_set_trip() function")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 6.3+ <stable@vger.kernel.org> # 6.3+
On thermal device interrupt, if the interrupt is generated for passing
workload hint, call the callback to pass notification to the user
space.
First call proc_thermal_check_wt_intr() to check interrupt, if this
callback returns true, wake the IRQ thread to call
proc_thermal_wt_intr_callback() to notify user space.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Subject adjustment, changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Prior to Meteor Lake processor generation, user space can pass workload
type request to the firmware. Then firmware can optimize power based on
the indicated workload type. User space also uses workload type requests
to implement its own heuristics.
The firmware in Meteor Lake processor generation is capable of predicting
workload type without software help.
To avoid duplicate processing, add a sysfs interface allowing user space
to obtain the workload hint from the firmware instead of trying to
predict the workload type by itself.
This workload hint is passed from the firmware via MMIO offset 0x5B18 of
the processor thermal PCI device. Before workload hints can be produced by
the firmware, it needs to be configured via a mailbox command. This
mailbox command turns ON the workload hint and it allows to program a
notification delay to control the rate of notifications.
The notification delay can be changed from user space vis sysfs.
Attribute group 'workload_hint' in sysfs is used for implementing the
workload hints interface between user space and the kernel.
It contains the following attributes:
workload_type_enable:
Enables/disables workload type hints from the firmware.
notification_delay_ms:
Notification delay in milliseconds.
workload_type_index:
The current workload type index predicted by the firmware (see
the documentation changes below for supported index values and
their meaning).
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog edits, documentation edits, whitespace adjustments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Meteor Lake processor supports firmware hints for predicting workload
type. So, remove support for passing workload hints to the firmware.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
[ rjw: Subject adjustment ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are issues in using MSI interrupts for processor thermal device.
The support is not consistent across generations. But the legacy PCI
interrupts work on all current generations.
Hence always use legacy PCI interrupts by default, instead of MSI.
Add a module param to use of MSI, so that MSI can be still used.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some features like workload type prediction and power floor events
require interrupt support to avoid polling. Here interrupts are enabled
and disabled via sending mailbox commands. The mailbox command ID is
0x1E for read and 0x1F for write.
The interrupt configuration will require mutex protection as it involves
read-modify-write operation. Since mutex are already used in the mailbox
read/write functions: send_mbox_write_cmd() and send_mbox_read_cmd(),
there will be double locking. But, this can be avoided by moving mutexes
from mailbox read/write processing functions to the callers:
processor_thermal_send_mbox_[read|write]_cmd().
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Adjust subject, fix up computation ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The processor thermal mailbox is used for workload type request and
also in the processor thermal RFIM module. So, move the workload type
request code to its own module from the current processor thermal
mailbox module.
processor_thermal_mailbox.c contains only mailbox read/write related
source code. The source related to workload_types requests is moved to
a module processor_thermal_wt_req.c.
In addition
- Rename PROC_THERMAL_FEATURE_MBOX to PROC_THERMAL_FEATURE_WT_REQ.
- proc_thermal_mbox_add(), which adds workload type sysfs attribute group
is renamed to proc_thermal_wt_req_add().
- proc_thermal_mbox_remove() is renamed to proc_thermal_wt_req_remove().
While here, resolve check patch warnings for 100 columns for only modified
lines.
No functional changes are expected.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit bc840ea5f9a9 ("thermal: core: Do not handle trip points with
invalid temperature") added a check for invalid temperature to the
disabled trip point check in handle_thermal_trip(), but that check was
added at a point when the trip structure has not been initialized yet.
This may cause handle_thermal_trip() to skip a valid trip point in some
cases, so fix it by moving the check to a suitable place, after
__thermal_zone_get_trip() has been called to populate the trip
structure.
Fixes: bc840ea5f9a9 ("thermal: core: Do not handle trip points with invalid temperature")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add 'const' to the definition of the 'trip' argument of the
.get_trend() thermal zone callback to indicate that the trip point
passed to it should not be modified by it and adjust the
callback functions implementing it, thermal_get_trend() in the
ACPI thermal driver and __ti_thermal_get_trend(), accordingly.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Michal Wilczynski <michal.wilczynski@intel.com>
for_each_child_of_node performs an of_node_get on each
iteration, so a break out of the loop requires an
of_node_put.
This was done using the Coccinelle semantic patch
iterators/for_each_child.cocci
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are no more users of thermal_zone_device_register(), so drop it
from the core.
Note that thermal_zone_device_register_with_trips() may be renamed to
thermal_zone_device_register() in the future, but only after a grace
period allowing all of the possible work in progress that may be using
the latter to adjust.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
All of the remaining callers of thermal_zone_device_register()
can use thermal_tripless_zone_device_register(), so make them
do so in order to allow the former to be dropped.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Multiple callers of thermal_zone_device_register() don't pass any trips
to it and they might use a shortened argument list for that, so add
a special function with fewer arguments for this purpose.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Passing a struct thermal_trip pointer instead of a trip index to the
.get_trend() thermal zone callback allows one of its 2 implementations,
the thermal_get_trend() function in the ACPI thermal driver, to be
simplified quite a bit, and the other implementation of it in the
ti-soc-thermal driver does not even use the relevant callback argument.
For this reason, change the .get_trend() thermal zone callback
definition and adjust the related code accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After recent changes in the ACPI thermal driver and in the Intel DTS
IOSF thermal driver, all thermal zone drivers are expected to use trip
tables for initialization and none of them should implement
.get_trip_type(), .get_trip_temp() or .get_trip_hyst() callbacks, so
drop these callbacks entirely from the core.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
.set_trips callback (Mikko Perttunen)
- Add the new Loongson-2 thermal sensor along with the DT bindings
(Yinbo Zhu)
- Use IS_ERR_OR_NULL helper to replace a double test on the TI bandgap
sensor (Li Zetao)
- Remove the call to platform_set_drvdata() as there is no call to
platform_get_drvdata() in a bunch of drivers where that happens
(Andrei Coardos)
- Switch the Mediatek LVTS mode to filtered in order to enable the
interrupts (Nícolas F. R. A. Prado)
- Fix Wvoid-pointer-to-enum-cast warning on the Exynos TMU (Krzysztof
Kozlowski)
- Remove redundant usage of of_match_ptr() as the driver db8500
already depends on CONFIG_OF (Ruan Jinjie)
- Remove redundant dev_err_probe() because the underlying function
already called it in the Mediatek sensor (Chen Jiahao)
- Free calibration nvmem after reading it on sun8i (Mark Brown)
- Remove useless comment in the code on sun8i (Yangtao Li)
- Make tsens_xxxx_nvmem static to fix sparse warning on QCom tsens (Min-Hua Chen)
- Remove error message at probe deferral on imx8mm (Ahmad Fatoum)
- Fix parameter check in lvts_debugfs_init with IS_ERR on Mediatek
LVTS (Minjie Du)
- Fix the interrupt routine and configuratoin for the Mediatek LVTS
(Nícolas F. R. A. Prado)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAmTtjxEACgkQqDIjiipP
6E+I6Qf6A8KAWre/B5L9F5PyhYomNsvNh9YPMZoyK6OARbJ8YORKbPTki2Fa8+8F
n757yahMw1yI36n/9euLpPdTXF1dW2rL44wrwGazWv/DJEM9OCQa9ExSY+GuI7OE
rN7asQmFF6Cjk7h4ha6wwsMO8jQ6htjcHEnLq/QA3x/RpVVb9JOJaSOXqlZUs7Q9
321DtHQ6WbIO/rPT4HoX+fRof+O2AWswvgudF1++p9GsxW+wn2eiJ+eD4hleuf9F
NteYqpHVXxo/XkMTDCZUMyY2dhS7LGjmRYXSYuTbpJnQU75VzNmGNG+8f1GqAZ3X
JoGPetiUkfqtAviB5eNTtE7JXz2lbw==
=sWIi
-----END PGP SIGNATURE-----
Merge tag 'thermal-v6.6-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Merge ARM and related thermal control updates for 6.6-rc1 from Daniel
Lezcano:
"- Check if the Tegra BPMP supports the trip points in order to set the
.set_trips callback (Mikko Perttunen)
- Add the new Loongson-2 thermal sensor along with the DT bindings
(Yinbo Zhu)
- Use IS_ERR_OR_NULL helper to replace a double test on the TI bandgap
sensor (Li Zetao)
- Remove the call to platform_set_drvdata() as there is no call to
platform_get_drvdata() in a bunch of drivers where that happens
(Andrei Coardos)
- Switch the Mediatek LVTS mode to filtered in order to enable the
interrupts (Nícolas F. R. A. Prado)
- Fix Wvoid-pointer-to-enum-cast warning on the Exynos TMU (Krzysztof
Kozlowski)
- Remove redundant usage of of_match_ptr() as the driver db8500
already depends on CONFIG_OF (Ruan Jinjie)
- Remove redundant dev_err_probe() because the underlying function
already called it in the Mediatek sensor (Chen Jiahao)
- Free calibration nvmem after reading it on sun8i (Mark Brown)
- Remove useless comment in the code on sun8i (Yangtao Li)
- Make tsens_xxxx_nvmem static to fix sparse warning on QCom tsens (Min-Hua Chen)
- Remove error message at probe deferral on imx8mm (Ahmad Fatoum)
- Fix parameter check in lvts_debugfs_init with IS_ERR on Mediatek
LVTS (Minjie Du)
- Fix the interrupt routine and configuratoin for the Mediatek LVTS
(Nícolas F. R. A. Prado)"
* tag 'thermal-v6.6-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (27 commits)
thermal/drivers/tegra-bpmp: Check if BPMP supports trip points
thermal: dt-bindings: add loongson-2 thermal
thermal/drivers/loongson-2: Add thermal management support
thermal/drivers/ti-soc-thermal: Use helper function IS_ERR_OR_NULL()
thermal/drivers/generic-adc: Removed unneeded call to platform_set_drvdata()
thermal/drivers/max77620_thermal: Removed unneeded call to platform_set_drvdata()
thermal/drivers/mediatek/auxadc_thermal: Removed call to platform_set_drvdata()
thermal/drivers/sun8i_thermal: Remove unneeded call to platform_set_drvdata()
thermal/drivers/broadcom/brcstb_thermal: Removed unneeded platform_set_drvdata()
thermal/drivers/mediatek/lvts_thermal: Make readings valid in filtered mode
thermal/drivers/k3_bandgap: Remove unneeded call to platform_set_drvdata()
thermal/drivers/k3_j72xx_bandgap: Removed unneeded call to platform_set_drvdata()
thermal/drivers/broadcom/sr-thermal: Removed call to platform_set_drvdata()
thermal/drivers/samsung: Fix Wvoid-pointer-to-enum-cast warning
thermal/drivers/db8500: Remove redundant of_match_ptr()
thermal/drivers/mediatek: Clean up redundant dev_err_probe()
thermal/drivers/sun8i: Free calibration nvmem after reading it
thermal/drivers/sun8i: Remove unneeded comments
thermal/drivers/tsens: Make tsens_xxxx_nvmem static
thermal/drivers/imx8mm: Suppress log message on probe deferral
...
- Make the ACPI thermal driver use its own Notify() handler (Michal
Wilczynski).
- Rework the ACPI thermal driver to use a table of generic trip point
structures on top of the internal representation of trip points and
remove thermal zone callbacks that are not necessary any more from
that driver (Rafael Wysocki).
- Fix a few issues in the Intel DTS IOSF thermal driver, clean up code
in it and make it pass tables of generic trip point structures to the
core during thermal zone registration (Rafael Wysocki).
- Drop a redundant check from the Intel DTS IOSF thermal driver's
"remove" routine (Zhang Rui).
- Use module_platform_driver() to replace an open-coded counterpart of
it in the int340x thermal driver (Yang Yingliang).
- Fix possible uninitialized value access in __thermal_of_bind() and
__thermal_of_unbind() (Peng Fan).
- Make the int3400 driver use thermal zone device wrappers (Daniel
Lezcano).
- Remove redundant thermal zone state check from the int340x thermal
driver (Daniel Lezcano).
- Drop non-functional nocrt parameter from ACPI thermal (Mario
Limonciello).
- Explicitly include correct DT includes in the thermal core and
drivers (Rob Herring).
-----BEGIN PGP SIGNATURE-----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=fHwc
-----END PGP SIGNATURE-----
Merge tag 'thermal-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These rework the Intel DTS IOSF and the ACPI thermal drivers to pass
tables of generic trip point structures to the core during
initialization and make some requisite modifications in the thermal
core, fix a few issues elsewhere and clean up code.
This includes changes that are present in the ACPI updates too,
because they involve both ACPI and the thermal core. The list of
specific changes below is limited to thermal control, however.
Specifics:
- Make the ACPI thermal driver use its own Notify() handler (Michal
Wilczynski)
- Rework the ACPI thermal driver to use a table of generic trip point
structures on top of the internal representation of trip points and
remove thermal zone callbacks that are not necessary any more from
that driver (Rafael Wysocki)
- Fix a few issues in the Intel DTS IOSF thermal driver, clean up
code in it and make it pass tables of generic trip point structures
to the core during thermal zone registration (Rafael Wysocki)
- Drop a redundant check from the Intel DTS IOSF thermal driver's
"remove" routine (Zhang Rui)
- Use module_platform_driver() to replace an open-coded counterpart
of it in the int340x thermal driver (Yang Yingliang)
- Fix possible uninitialized value access in __thermal_of_bind() and
__thermal_of_unbind() (Peng Fan)
- Make the int3400 driver use thermal zone device wrappers (Daniel
Lezcano)
- Remove redundant thermal zone state check from the int340x thermal
driver (Daniel Lezcano)
- Drop non-functional nocrt parameter from ACPI thermal (Mario
Limonciello)
- Explicitly include correct DT includes in the thermal core and
drivers (Rob Herring)"
* tag 'thermal-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: intel: intel_soc_dts_iosf: Remove redundant check
thermal: intel: int340x: simplify the code with module_platform_driver()
thermal/of: Fix potential uninitialized value access
thermal: intel: intel_soc_dts_iosf: Use struct thermal_trip
thermal: intel: intel_soc_dts_iosf: Rework critical trip setup
thermal: intel: intel_soc_dts_iosf: Add helper for resetting trip points
thermal: intel: intel_soc_dts_iosf: Change initialization ordering
thermal: intel: intel_soc_dts_iosf: Pass sensors to update_trip_temp()
thermal: intel: intel_soc_dts_iosf: Untangle update_trip_temp()
thermal: intel: intel_soc_dts_iosf: Always assume notification support
thermal: intel: intel_soc_dts_iosf: Drop redundant symbol definition
thermal: intel: intel_soc_dts_iosf: Always use 2 trips
thermal: Explicitly include correct DT includes
thermal/drivers/int340x: Do not check the thermal zone state
thermal/drivers/int3400: Use thermal zone device wrappers
- Update the ACPICA code in the kernel to upstream revision 20230628
including the following changes:
* Suppress a GCC 12 dangling-pointer warning (Philip Prindeville).
* Reformat the ACPI_STATE_COMMON macro and its users (George Guo).
* Replace the ternary operator with ACPI_MIN() (Jiangshan Yi).
* Add support for _DSC as per ACPI 6.5 (Saket Dumbre).
* Remove a duplicate macro from zephyr header (Najumon B.A).
* Add data structures for GED and _EVT tracking (Jose Marinho).
* Fix misspelled CDAT DSMAS define (Dave Jiang).
* Simplify an error message in acpi_ds_result_push() (Christophe
Jaillet).
* Add a struct size macro related to SRAT (Dave Jiang).
* Add AML_NO_OPERAND_RESOLVE flag to Timer (Abhishek Mainkar).
* Add support for RISC-V external interrupt controllers in MADT (Sunil
V L).
* Add RHCT flags, CMO and MMU nodes (Sunil V L).
* Change ACPICA version to 20230628 (Bob Moore).
- Introduce new wrappers for ACPICA notify handler install/remove and
convert multiple drivers to using their own Notify() handlers instead
of the ACPI bus type .notify() slated for removal (Michal Wilczynski).
- Add backlight=native DMI quirk for Apple iMac12,1 and iMac12,2 (Hans
de Goede).
- Put ACPI video and its child devices explicitly into D0 on boot to
avoid platform firmware confusion (Kai-Heng Feng).
- Add backlight=native DMI quirk for Lenovo Ideapad Z470 (Jiri Slaby).
- Support obtaining physical CPU ID from MADT on LoongArch (Bibo Mao).
- Convert ACPI CPU initialization to using _OSC instead of _PDC that
has been depreceted since 2018 and dropped from the specification in
ACPI 6.5 (Michal Wilczynski, Rafael Wysocki).
- Drop non-functional nocrt parameter from ACPI thermal (Mario
Limonciello).
- Clean up the ACPI thermal driver, rework the handling of firmware
notifications in it and make it provide a table of generic trip point
structures to the core during initialization (Rafael Wysocki).
- Defer enumeration of devices with _DEP pointing to IVSC (Wentong Wu).
- Install SystemCMOS address space handler for ACPI000E (TAD) to meet
platform firmware expectations on some platforms (Zhang Rui).
- Fix finding the generic error data in the ACPi extlog driver for
compatibility with old and new firmware interface versions (Xiaochun
Lee).
- Remove assorted unused declarations of functions (Yue Haibing).
- Move AMBA bus scan handling into arm64 specific directory (Sudeep
Holla).
- Fix and clean up suspend-to-idle interface for AMD systems (Mario
Limonciello, Andy Shevchenko).
- Fix string truncation warning in pnpacpi_add_device() (Sunil V L).
-----BEGIN PGP SIGNATURE-----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=aXc6
-----END PGP SIGNATURE-----
Merge tag 'acpi-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These include new ACPICA material, a rework of the ACPI thermal
driver, a switch-over of the ACPI processor driver to using _OSC
instead of (long deprecated) _PDC for CPU initialization, a rework of
firmware notifications handling in several drivers, fixes and cleanups
for suspend-to-idle handling on AMD systems, ACPI backlight driver
updates and more.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20230628
including the following changes:
- Suppress a GCC 12 dangling-pointer warning (Philip Prindeville)
- Reformat the ACPI_STATE_COMMON macro and its users (George Guo)
- Replace the ternary operator with ACPI_MIN() (Jiangshan Yi)
- Add support for _DSC as per ACPI 6.5 (Saket Dumbre)
- Remove a duplicate macro from zephyr header (Najumon B.A)
- Add data structures for GED and _EVT tracking (Jose Marinho)
- Fix misspelled CDAT DSMAS define (Dave Jiang)
- Simplify an error message in acpi_ds_result_push() (Christophe
Jaillet)
- Add a struct size macro related to SRAT (Dave Jiang)
- Add AML_NO_OPERAND_RESOLVE flag to Timer (Abhishek Mainkar)
- Add support for RISC-V external interrupt controllers in MADT
(Sunil V L)
- Add RHCT flags, CMO and MMU nodes (Sunil V L)
- Change ACPICA version to 20230628 (Bob Moore)
- Introduce new wrappers for ACPICA notify handler install/remove and
convert multiple drivers to using their own Notify() handlers
instead of the ACPI bus type .notify() slated for removal (Michal
Wilczynski)
- Add backlight=native DMI quirk for Apple iMac12,1 and iMac12,2
(Hans de Goede)
- Put ACPI video and its child devices explicitly into D0 on boot to
avoid platform firmware confusion (Kai-Heng Feng)
- Add backlight=native DMI quirk for Lenovo Ideapad Z470 (Jiri Slaby)
- Support obtaining physical CPU ID from MADT on LoongArch (Bibo Mao)
- Convert ACPI CPU initialization to using _OSC instead of _PDC that
has been depreceted since 2018 and dropped from the specification
in ACPI 6.5 (Michal Wilczynski, Rafael Wysocki)
- Drop non-functional nocrt parameter from ACPI thermal (Mario
Limonciello)
- Clean up the ACPI thermal driver, rework the handling of firmware
notifications in it and make it provide a table of generic trip
point structures to the core during initialization (Rafael Wysocki)
- Defer enumeration of devices with _DEP pointing to IVSC (Wentong
Wu)
- Install SystemCMOS address space handler for ACPI000E (TAD) to meet
platform firmware expectations on some platforms (Zhang Rui)
- Fix finding the generic error data in the ACPi extlog driver for
compatibility with old and new firmware interface versions
(Xiaochun Lee)
- Remove assorted unused declarations of functions (Yue Haibing)
- Move AMBA bus scan handling into arm64 specific directory (Sudeep
Holla)
- Fix and clean up suspend-to-idle interface for AMD systems (Mario
Limonciello, Andy Shevchenko)
- Fix string truncation warning in pnpacpi_add_device() (Sunil V L)"
* tag 'acpi-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (66 commits)
ACPI: x86: s2idle: Add a function to get LPS0 constraint for a device
ACPI: x86: s2idle: Add for_each_lpi_constraint() helper
ACPI: x86: s2idle: Add more debugging for AMD constraints parsing
ACPI: x86: s2idle: Fix a logic error parsing AMD constraints table
ACPI: x86: s2idle: Catch multiple ACPI_TYPE_PACKAGE objects
ACPI: x86: s2idle: Post-increment variables when getting constraints
ACPI: Adjust #ifdef for *_lps0_dev use
ACPI: TAD: Install SystemCMOS address space handler for ACPI000E
ACPI: Remove assorted unused declarations of functions
ACPI: extlog: Fix finding the generic error data for v3 structure
PNP: ACPI: Fix string truncation warning
ACPI: Remove unused extern declaration acpi_paddr_to_node()
ACPI: video: Add backlight=native DMI quirk for Apple iMac12,1 and iMac12,2
ACPI: video: Put ACPI video and its child devices into D0 on boot
ACPI: processor: LoongArch: Get physical ID from MADT
ACPI: scan: Defer enumeration of devices with a _DEP pointing to IVSC device
ACPI: thermal: Eliminate code duplication from acpi_thermal_notify()
ACPI: thermal: Drop unnecessary thermal zone callbacks
ACPI: thermal: Rework thermal_get_trend()
ACPI: thermal: Use trip point table to register thermal zones
...
Merge ACPI thermal driver changes for 6.6-rc1:
- Drop non-functional nocrt parameter from ACPI thermal (Mario
Limonciello).
- Clean up the ACPI thermal driver, rework the handling of firmware
notifications in it and make it provide a table of generic trip point
structures to the core during initialization (Rafael Wysocki).
* acpi-thermal:
ACPI: thermal: Eliminate code duplication from acpi_thermal_notify()
ACPI: thermal: Drop unnecessary thermal zone callbacks
ACPI: thermal: Rework thermal_get_trend()
ACPI: thermal: Use trip point table to register thermal zones
thermal: core: Rework and rename __for_each_thermal_trip()
ACPI: thermal: Introduce struct acpi_thermal_trip
ACPI: thermal: Carry out trip point updates under zone lock
ACPI: thermal: Clean up acpi_thermal_register_thermal_zone()
thermal: core: Add priv pointer to struct thermal_trip
thermal: core: Introduce thermal_zone_device_exec()
thermal: core: Do not handle trip points with invalid temperature
ACPI: thermal: Drop redundant local variable from acpi_thermal_resume()
ACPI: thermal: Do not attach private data to ACPI handles
ACPI: thermal: Drop enabled flag from struct acpi_thermal_active
ACPI: thermal: Drop nocrt parameter
These remove a redundant check from a driver's "remove" routine
and use module_platform_driver() to replace an open-coded version
of it in one driver.
* thermal-intel:
thermal: intel: intel_soc_dts_iosf: Remove redundant check
thermal: intel: int340x: simplify the code with module_platform_driver()
Remove the redundant check in remove_dts_thermal_zone() because all of
its existing callers pass a valid pointer as the argument.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The init/exit() of the driver only calls platform_driver_{un}register(),
so it can be simpilfied by using module_platform_driver().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If of_parse_phandle_with_args() called from __thermal_of_bind() or
__thermal_of_unbind() fails, cooling_spec.np will not be initialized,
so move the of_node_put() calls below the respective return value checks
to avoid dereferencing an uninitialized pointer.
Fixes: 3fd6d6e2b4e8 ("thermal/of: Rework the thermal device tree initialization")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Check if BPMP supports thermal trip points, and if not,
do not expose the .set_trips callback to the thermal core
framework. This can happen in virtualized environments
where asynchronous communication with VM BPMP drivers is not
available.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20221129153914.2699041-1-cyndis@kapsi.fi
This reworks the ACPI thermal driver to use a table of generic trip
point structures on top of the internal representation of trip points
and removes thermal zone callbacks that are not necessary any more
from it.
It requires some relatively small changes to be made in the thermal core
too and it is based on top of changes reworking ACPI device notification
handling that are included in this merge.
* acpi-thermal: (24 commits)
ACPI: thermal: Eliminate code duplication from acpi_thermal_notify()
ACPI: thermal: Drop unnecessary thermal zone callbacks
ACPI: thermal: Rework thermal_get_trend()
ACPI: thermal: Use trip point table to register thermal zones
thermal: core: Rework and rename __for_each_thermal_trip()
ACPI: thermal: Introduce struct acpi_thermal_trip
ACPI: thermal: Carry out trip point updates under zone lock
ACPI: thermal: Clean up acpi_thermal_register_thermal_zone()
thermal: core: Add priv pointer to struct thermal_trip
thermal: core: Introduce thermal_zone_device_exec()
thermal: core: Do not handle trip points with invalid temperature
ACPI: thermal: Drop redundant local variable from acpi_thermal_resume()
ACPI: thermal: Do not attach private data to ACPI handles
ACPI: thermal: Drop enabled flag from struct acpi_thermal_active
ACPI: thermal: Drop nocrt parameter
ACPI: thermal: Install Notify() handler directly
ACPI: NFIT: Remove unnecessary .remove callback
ACPI: NFIT: Install Notify() handler directly
ACPI: HED: Install Notify() handler directly
ACPI: battery: Install Notify() handler directly
...
These fix a few issues in the Intel DTS IOSF thermal driver, clean up
code in it and make it use trip point tables for registering thermal
zones.
* thermal-intel:
thermal: intel: intel_soc_dts_iosf: Use struct thermal_trip
thermal: intel: intel_soc_dts_iosf: Rework critical trip setup
thermal: intel: intel_soc_dts_iosf: Add helper for resetting trip points
thermal: intel: intel_soc_dts_iosf: Change initialization ordering
thermal: intel: intel_soc_dts_iosf: Pass sensors to update_trip_temp()
thermal: intel: intel_soc_dts_iosf: Untangle update_trip_temp()
thermal: intel: intel_soc_dts_iosf: Always assume notification support
thermal: intel: intel_soc_dts_iosf: Drop redundant symbol definition
thermal: intel: intel_soc_dts_iosf: Always use 2 trips
Rework the currently unused __for_each_thermal_trip() to pass original
pointers to struct thermal_trip objects to the callback, so it can be
used for updating trip data (e.g. temperatures), rename it to
for_each_thermal_trip() and make it available to modular drivers.
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce a new helper function, thermal_zone_device_exec(), that can
be used by drivers to run a given callback routine under the zone lock.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds the support for Loongson-2 thermal sensor controller,
which can support maximum four sensor selectors that corresponding to four
sets of thermal control registers and one set of sampling register. The
sensor selector can selector a speific thermal sensor as temperature input.
The sampling register is used to obtain the temperature in real time, the
control register GATE field is used to set the threshold of high or low
temperature, when the input temperature is higher than the high temperature
threshold or lower than the low temperature threshold, an interrupt will
occur.
Signed-off-by: zhanghongchen <zhanghongchen@loongson.cn>
Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230817021007.10350-1-zhuyinbo@loongson.cn
Use IS_ERR_OR_NULL() to detect an error pointer or a null pointer
open-coding to simplify the code.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230817014900.3094512-1-lizetao1@huawei.com
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230814180921.3336-1-aboutphysycs@gmail.com
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230811191548.3340-1-aboutphysycs@gmail.com
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230811192847.3838-1-aboutphysycs@gmail.com
