IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
It is meaningless to handle any interrupts after disconnecting
with host
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Below is the recommendation from Cadence designer:
Using this bit to be sure that PHY clock is keeping up in active
state. It's good to keep Fast Access bit enabled as long as there
is any access to USB register.
It is used to fix the potential ARM core hang when visit controller
register after DEVDS (.pullup is cleared) is set, the threaded irq
may be scheduled at that time.
Cc: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the board uses role switch class for switching the role, it should
not depends on SoC OTG hardware siginal any more, so quit early.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Similar to some other IA platforms, Elkhart Lake too depends on the
PMU register write to request transition of Dx power state.
Thus, we add the PCI_DEVICE_ID_INTEL_EHLLP to the list of devices that
shall execute the ACPI _DSM method during D0/D3 sequence.
[heikki.krogerus@linux.intel.com: included Fixes tag]
Fixes: dbb0569de852 ("usb: dwc3: pci: Add Support for Intel Elkhart Lake Devices")
Cc: stable@vger.kernel.org
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch replace config_ep_by_speed with config_ep_by_speed_and_alt.
This change allows to select proper usb_ss_ep_comp_descriptor for each
stream capable endpoints.
f_tcm function for SS use array of headers for both BOT/UAS alternate
setting:
static struct usb_descriptor_header *uasp_ss_function_desc[] = {
(struct usb_descriptor_header *) &bot_intf_desc,
(struct usb_descriptor_header *) &uasp_ss_bi_desc,
(struct usb_descriptor_header *) &bot_bi_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_ss_bo_desc,
(struct usb_descriptor_header *) &bot_bo_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_intf_desc,
(struct usb_descriptor_header *) &uasp_ss_bi_desc,
(struct usb_descriptor_header *) &uasp_bi_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_bi_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_bo_desc,
(struct usb_descriptor_header *) &uasp_bo_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_bo_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_status_desc,
(struct usb_descriptor_header *) &uasp_status_in_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_status_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_cmd_desc,
(struct usb_descriptor_header *) &uasp_cmd_comp_desc,
(struct usb_descriptor_header *) &uasp_cmd_pipe_desc,
NULL,
};
The first 5 descriptors are associated with BOT alternate setting,
and others are associated with UAS.
During handling UAS alternate setting f_tcm driver invokes
config_ep_by_speed and this function sets incorrect companion endpoint
descriptor in usb_ep object.
Instead setting ep->comp_desc to uasp_bi_ep_comp_desc function in this
case set ep->comp_desc to bot_uasp_ss_bi_desc.
And in result it uses the descriptor from BOT alternate setting
instead UAS.
Finally, it causes that controller driver during enabling endpoints
detect that just enabled endpoint for bot.
Signed-off-by: Jayshri Pawar <jpawar@cadence.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
adds the specific compatible string for the DWC2 IP found in the APM82181
SoCs. The IP is setup correctly through the auto detection... With the
exception of the AHB Burst Size. The default of GAHBCFG_HBSTLEN_INCR4 of
the "snps,dwc2" can cause a system hang when the USB and SATA is used
concurrently. Because the predecessor (PPC460EX (Canyonlands)) already
had the same problem, this SoC can make use of the existing
dwc2_set_amcc_params() function.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
commit 2b74b0a04d3e ("USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()")
adds important bounds checking however it unfortunately also introduces a
bug with respect to section 3.3.1 of the NCM specification.
wDatagramIndex[1] : "Byte index, in little endian, of the second datagram
described by this NDP16. If zero, then this marks the end of the sequence
of datagrams in this NDP16."
wDatagramLength[1]: "Byte length, in little endian, of the second datagram
described by this NDP16. If zero, then this marks the end of the sequence
of datagrams in this NDP16."
wDatagramIndex[1] and wDatagramLength[1] respectively then may be zero but
that does not mean we should throw away the data referenced by
wDatagramIndex[0] and wDatagramLength[0] as is currently the case.
Breaking the loop on (index2 == 0 || dg_len2 == 0) should come at the end
as was previously the case and checks for index2 and dg_len2 should be
removed since zero is valid.
I'm not sure how much testing the above patch received but for me right now
after enumeration ping doesn't work. Reverting the commit restores ping,
scp, etc.
The extra validation associated with wDatagramIndex[0] and
wDatagramLength[0] appears to be valid so, this change removes the incorrect
restriction on wDatagramIndex[1] and wDatagramLength[1] restoring data
processing between host and device.
Fixes: 2b74b0a04d3e ("USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()")
Cc: Ilja Van Sprundel <ivansprundel@ioactive.com>
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
USB2.0 PHY hangs in Rx Compliance test when the incoming packet
amplitude is varied below and above the Squelch Level of
Receiver during the active packet multiple times.
Version 1 of the controller allows PHY to be reset when RX fail condition
is detected to work around the above issue. This feature is
disabled by default and needs to be enabled using a bit from
the newly added PHYRST_CFG register. This patch enables the workaround.
There is no way to know controller version before device controller
is started and the workaround needs to be applied for both host and
device modes, so we rely on a DT property do decide when to
apply the workaround.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The Amlogic AXG is close to the GXL Glue but with a single OTG PHY.
It needs the same init sequence as GXL & GXM, but it seems it doesn't need
the host disconnect bit.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This switches the PCH UDC driver to use GPIO descriptors. The way
this is supposed to be used is confusing. The code contains the
following:
/* GPIO port for VBUS detecting */
static int vbus_gpio_port = -1; /* GPIO port number (-1:Not used) */
So a hardcoded GPIO number in the code. Further the probe() path
very clearly will exit if the GPIO is not found, so this driver
can only be configured by editing the code, hard-coding a GPIO
number into this variable.
This is simply not how we do things. My guess is that this is
used in products by patching a GPIO number into this variable and
shipping a kernel that is compile-time tailored for the target
system.
I switched this mechanism to using a GPIO descriptor associated
with the parent PCI device. This can be added by using the 16bit
subsystem ID or similar to identify which exact machine we are
running on and what GPIO is present on that machine, and then
add a GPIO descriptor using gpiod_add_lookup_table() from
<linux/gpio/machine.h>. Since I don't have any target systems
I cannot add this but I'm happy to help. I put in a FIXME so
the people actually using this driver knows what to do.
Cc: Felipe Balbi <balbi@kernel.org>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Introduce runtime PM and wakeup interrupt handler for cdns3,
the runtime PM is default off since other cdns3 may not
implement glue layer support for runtime PM.
One typical wakeup event use case is xHCI runtime suspend will clear
USBCMD.RS bit, after that the xHCI will not trigger any interrupts,
so its parent (cdns core device) needs to resume xHCI device when
any (wakeup) events occurs at host port.
When the controller is in low power mode, the lpm flag will be set.
The interrupt triggered later than lpm flag is set considers as
wakeup interrupt and handled at cdns_wakeup_irq. Once the wakeup
occurs, it first disables interrupt to avoid later interrupt
occurrence since the controller is in low power mode at that
time, and access registers may be invalid at that time. At wakeup
handler, it will call pm_request_resume to wakeup xHCI device, and
at runtime resume handler, it will enable interrupt again.
The API platform_suspend is introduced for glue layer to implement
platform specific PM sequence.
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Since we have both USB2 and USB3 PHYs for cdns3 controller, it is
better we have unity APIs to handle both USB2 and USB3's power, it
could simplify code for error handling and further power management
implementation.
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Make debugging real problems easier by not trying to disable an EP that
was not yet enabled.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This is a follow-on patch for commit a23be4ed8f48 ("usb: gadget: aspeed:
improve vhub port irq handling"): for_each_set_bit() is replaced with
simple for() loop because for() loop runs faster on ASPEED BMC.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following sparse warning:
drivers/usb/dwc3/trace.c: note: in included file (through drivers/usb/dwc3/trace.h):
drivers/usb/dwc3/debug.h:374:39: warning: cast to non-scalar
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add interconnect support in dwc3-qcom driver to vote for bus
bandwidth.
This requires for two different paths - from USB to
DDR. The other is from APPS to USB.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The UDC NET2272 driver includes <linux/gpio.h> but does not
use any symbols from this file, so drop the include.
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The DPRAM memory from the USB High Speed Device Port (UDPHS) hardware
block was increased. This patch updates the endpoint allocation for sam9x60
to take advantage of this larger memory. At the same time the
constraint to allocate the endpoints in order was lifted. To handle old
and new hardware in the same driver the ep_prealloc was added.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Use 1 bank endpoints for control transfers
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Simplify the endpoint allocation and cleanup the code.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Instead of trying to match every possible compatible use
of_find_matching_node_and_match() and pass the compatible array.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Call dwc2_debugfs_exit() and dwc2_hcd_remove() (if the HCD was enabled
earlier) when usb_add_gadget_udc() has failed. This ensures that the
debugfs entries created by dwc2_debugfs_init() as well as the HCD are
cleaned up in the error path.
Fixes: 207324a321a866 ("usb: dwc2: Postponed gadget registration to the udc class driver")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The user may have more information to override the HW parameter to
specify the maximum_speed. However, if the user specifies a
maximum_speed that the controller doesn't support, print out a warning.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the maximum_speed is not specified, default the device speed base on
its HW capability. Don't prematurely check HW capability before
validating the maximum_speed device property. The device property takes
precedence in dwc->maximum_speed.
Fixes: 0e1e5c47f7a9 ("usb: dwc3: add support for USB 2.0-only core configuration")
Reported-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
According the programming guide (for all DWC3 IPs), when the driver
handles ClearFeature(halt) request, it should issue CLEAR_STALL command
_after_ the END_TRANSFER command completes. The END_TRANSFER command may
take some time to complete. So, delay the ClearFeature(halt) request
control status stage and wait for END_TRANSFER command completion
interrupt. Only after END_TRANSFER command completes that the driver
may issue CLEAR_STALL command.
Cc: stable@vger.kernel.org
Fixes: cb11ea56f37a ("usb: dwc3: gadget: Properly handle ClearFeature(halt)")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The function driver may queue new requests right after halting the
endpoint (i.e. queue new requests while the endpoint is stalled).
There's no restriction preventing it from doing so. However, dwc3
currently drops those requests after CLEAR_STALL. The driver should only
drop started requests. Keep the pending requests in the pending list to
resume and process them after the host issues ClearFeature(Halt) to the
endpoint.
Cc: stable@vger.kernel.org
Fixes: cb11ea56f37a ("usb: dwc3: gadget: Properly handle ClearFeature(halt)")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The CRC calculation done by genksyms is triggered when the parser hits
EXPORT_SYMBOL*() macros. At this point, genksyms recursively expands the
types of the function parameters, and uses that as the input for the CRC
calculation. In the case of forward-declared structs, the type expands
to 'UNKNOWN'. Following this, it appears that the result of the
expansion of each type is cached somewhere, and seems to be re-used
when/if the same type is seen again for another exported symbol in the
same C file.
Unfortunately, this can cause CRC 'stability' issues when a struct
definition becomes visible in the middle of a C file. For example, let's
assume code with the following pattern:
struct foo;
int bar(struct foo *arg)
{
/* Do work ... */
}
EXPORT_SYMBOL_GPL(bar);
/* This contains struct foo's definition */
#include "foo.h"
int baz(struct foo *arg)
{
/* Do more work ... */
}
EXPORT_SYMBOL_GPL(baz);
Here, baz's CRC will be computed using the expansion of struct foo that
was cached after bar's CRC calculation ('UNKOWN' here). But if
EXPORT_SYMBOL_GPL(bar) is removed from the file (because of e.g. symbol
trimming using CONFIG_TRIM_UNUSED_KSYMS), struct foo will be expanded
late, during baz's CRC calculation, which now has visibility over the
full struct definition, hence resulting in a different CRC for baz.
The proper fix for this certainly is in genksyms, but that will take me
some time to get right. In the meantime, we have seen one occurrence of
this in the ehci-hcd code which hits this problem because of the way it
includes C files halfway through the code together with an unlucky mix
of symbol trimming.
In order to workaround this, move the include done in ehci-hub.c early
in ehci-hcd.c, hence making sure the struct definitions are visible to
the entire file. This improves CRC stability of the ehci-hcd exports
even when symbol trimming is enabled.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20200916171825.3228122-1-qperret@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check and return if there are errors. The response bits are valid
only on no errors.
Fixes: b7404a29cd3d ("usb: typec: intel_pmc_mux: Definitions for response status bits")
Signed-off-by: Madhusudanarao Amara <madhusudanarao.amara@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916091102.27118-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk for the BYD zhaoxin notebook.
This notebook come with usb touchpad. And we would like to disable
touchpad wakeup on this notebook by default.
Signed-off-by: Penghao <penghao@uniontech.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200907023026.28189-1-penghao@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCSI layer can go into an ugly loop if you ignore that a device is
gone. You need to report an error in the command rather than in the
return value of the queue method.
We need to specifically check for ENODEV. The issue goes back to the
introduction of the driver.
Fixes: 115bb1ffa54c3 ("USB: Add UAS driver")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200916094026.30085-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
