IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
I'm seeing series of e1000e resets (sometimes endless) at system boot
if something generates tx traffic at this time. In my case this is
netconsole who sends message "e1000e 0000:02:00.0: Some CPU C-states
have been disabled in order to enable jumbo frames" from e1000e itself.
As result e1000_watchdog_task sees used tx buffer while carrier is off
and start this reset cycle again.
[ 17.794359] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 17.794714] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 22.936455] e1000e 0000:02:00.0 eth1: changing MTU from 1500 to 9000
[ 23.033336] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 26.102364] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 27.174495] 8021q: 802.1Q VLAN Support v1.8
[ 27.174513] 8021q: adding VLAN 0 to HW filter on device eth1
[ 30.671724] cgroup: cgroup: disabling cgroup2 socket matching due to net_prio or net_cls activation
[ 30.898564] netpoll: netconsole: local port 6666
[ 30.898566] netpoll: netconsole: local IPv6 address 2a02:6b8:0:80b:beae:c5ff:fe28:23f8
[ 30.898567] netpoll: netconsole: interface 'eth1'
[ 30.898568] netpoll: netconsole: remote port 6666
[ 30.898568] netpoll: netconsole: remote IPv6 address 2a02:6b8:b000:605c:e61d:2dff:fe03:3790
[ 30.898569] netpoll: netconsole: remote ethernet address b0:a8:6e:f4:ff:c0
[ 30.917747] console [netcon0] enabled
[ 30.917749] netconsole: network logging started
[ 31.453353] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.185730] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.321840] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.465822] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.597423] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.745417] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.877356] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.005441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.157376] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.289362] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.417441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 37.790342] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
This patch flushes tx buffers only once when carrier is off
rather than at each watchdog iteration.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the 'igc_get_link_up_info_base method' from igc_base.c file.
Use the 'igc_get_speed_and_duplex_copper' method directly and reduce
the code redundancy.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unused igc_adv_data_desc definition from igc_base.h file.
Descriptors definition will be added per demand.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The change is based on the issue found by Kangjie Lu <kjlu@umn.edu> where
we not checking the return value of a register read/write which could result
in a NULL pointer dereference if the read/write fails.
Since we are only trying to disable the far-end loopback, if the read
and write of register fails, we do not want to bail out of the function.
We just want to log that it failed to disable and continue on.
CC: Sasha Neftin <sasha.neftin@intel.com>
CC: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function comment for fm10k_iov_msg_msix_pf has an extra space in
a sentence, which is unnecessary.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_reset_hw_82599() resets the value of hw->mac.num_rar_entries to
pre-defined value of 128. Let's get rid of that hardcoded literal, and use
IXGBE_82599_RAR_ENTRIES instead, the same way the normal initialization
path does.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove redundant igc_check_for_link_base code and replace it with
an igc_check_for_copper_link method.
Fix duplication of IGC_ADVTXD_PAYLEN_SHIFT mask declaration.
Remove obsolete IGC_SCVPC register definition.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Address community comment.
Remove the unreachable code leads to the static checker warning.
PHY functionality will be added later per demand.
Reported by Dan Carpenter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000e sets different WoL settings in system suspend callback and
runtime suspend callback.
The suspend direct complete optimization leaves e1000e in runtime
suspended state with wrong WoL setting during system suspend.
To fix this, we need to disable suspend direct complete optimization to
let e1000e always use suspend callback to set correct WoL during system
suspend.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sven Auhagen reports that if he changes a SFP+ module for a SFP module
on the Macchiatobin Single Shot, the link does not come back up. For
Sven, it is as easy as:
- Insert a SFP+ module connected, and use ping6 to verify link is up.
- Remove SFP+ module
- Insert SFP 1000base-X module use ping6 to verify link is up: Link
up event did not trigger and the link is down
but that doesn't show the problem for me. Locally, this has been
reproduced by:
- Boot with no modules.
- Insert SFP+ module, confirm link is up.
- Replace module with 25000base-X module. Confirm link is up.
- Set remote end down, link is reported as dropped at both ends.
- Set remote end up, link is reported up at remote end, but not local
end due to lack of link interrupt.
Fix this by setting up both GMAC and XLG interrupts for port 0, but
only unmasking the appropriate interrupt according to the current mode
set in the mac_config() method. However, only do the mask/unmask
dance when we are really changing the link mode to avoid missing any
link interrupts.
Tested-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the phy_interface_mode_is_8023z() helper for detecting interface
modes that use 802.3z serial encoding. This is equivalent to testing
for both 1000base-X and 2500base-X.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for fixed-link configurations to nixge driver.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make MDIO child optional and only instantiate the
MDIO bus if the child is actually present.
There are currently no (in-tree) users of this
binding; all (out-of-tree) users use overlays that
get shipped together with the FPGA images that contain
the IP.
This will significantly increase maintainabilty
of future revisions of this IP.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users of the fixed_phy_add() pass -1 as GPIO number
to the fixed phy driver, and all users of fixed_phy_register()
pass -1 as GPIO number as well, except for the device
tree MDIO bus.
Any new users should create a proper device and pass the
GPIO as a descriptor associated with the device so delete
the GPIO argument from the calls and drop the code looking
requesting a GPIO in fixed_phy_add().
In fixed phy_register(), investigate the "fixed-link"
node and pick the GPIO descriptor from "link-gpios" if
this property exists. Move the corresponding code out
of of_mdio.c as the fixed phy code anyways requires
OF to be in use.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the tab before '}' and keep the code style consistent.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SH7763 SoC manual describes the Ether MAC's RX checksum offload
the same way as it's implemented in the EtherAVB MACs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SH7734 SoC manual describes the Ether MAC's RX checksum offload
the same way as it's implemented in the EtherAVB MACs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The R-Car V3H (R8A77980) SoC manual describes the Ether MAC's RX checksum
offload the same way as it's implemented in the EtherAVB MAC...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The R-Mobile A1 (R8A7740) SoC manual describes the Ether MAC's RX checksum
offload the same way as it's implemented in the EtherAVB MAC...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RZ/A1H (R7S721000) SoC manual describes the Ether MAC's RX checksum
offload the same way as it's implemented in the EtherAVB MACs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the RX checksum offload. This is enabled by default and
may be disabled and re-enabled using 'ethtool':
# ethtool -K eth0 rx off
# ethtool -K eth0 rx on
Some Ether MACs provide a simple checksumming scheme which appears to be
completely compatible with CHECKSUM_COMPLETE: sum of all packet data after
the L2 header is appended to packet data; this may be trivially read by
the driver and used to update the skb accordingly. The same checksumming
scheme is implemented in the EtherAVB MACs and now supported by the 'ravb'
driver.
In terms of performance, throughput is close to gigabit line rate with the
RX checksum offload both enabled and disabled. The 'perf' output, however,
appears to indicate that significantly less time is spent in do_csum() --
this is as expected.
Test results with RX checksum offload enabled:
~/netperf-2.2pl4# perf record -a ./netperf -t TCP_MAERTS -H 192.168.2.4
TCP MAERTS TEST to 192.168.2.4
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
131072 16384 16384 10.01 933.93
[ perf record: Woken up 8 times to write data ]
[ perf record: Captured and wrote 1.955 MB perf.data (41940 samples) ]
~/netperf-2.2pl4# perf report
Samples: 41K of event 'cycles:ppp', Event count (approx.): 9915302763
Overhead Command Shared Object Symbol
9.44% netperf [kernel.kallsyms] [k] __arch_copy_to_user
7.75% swapper [kernel.kallsyms] [k] _raw_spin_unlock_irq
6.31% swapper [kernel.kallsyms] [k] default_idle_call
5.89% swapper [kernel.kallsyms] [k] arch_cpu_idle
4.37% swapper [kernel.kallsyms] [k] tick_nohz_idle_exit
4.02% netperf [kernel.kallsyms] [k] _raw_spin_unlock_irq
2.52% netperf [kernel.kallsyms] [k] preempt_count_sub
1.81% netperf [kernel.kallsyms] [k] tcp_recvmsg
1.80% netperf [kernel.kallsyms] [k] _raw_spin_unlock_irqres
1.78% netperf [kernel.kallsyms] [k] preempt_count_add
1.36% netperf [kernel.kallsyms] [k] __tcp_transmit_skb
1.20% netperf [kernel.kallsyms] [k] __local_bh_enable_ip
1.10% netperf [kernel.kallsyms] [k] sh_eth_start_xmit
Test results with RX checksum offload disabled:
~/netperf-2.2pl4# perf record -a ./netperf -t TCP_MAERTS -H 192.168.2.4
TCP MAERTS TEST to 192.168.2.4
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
131072 16384 16384 10.01 932.04
[ perf record: Woken up 14 times to write data ]
[ perf record: Captured and wrote 3.642 MB perf.data (78817 samples) ]
~/netperf-2.2pl4# perf report
Samples: 78K of event 'cycles:ppp', Event count (approx.): 18091442796
Overhead Command Shared Object Symbol
7.00% swapper [kernel.kallsyms] [k] do_csum
3.94% swapper [kernel.kallsyms] [k] sh_eth_poll
3.83% ksoftirqd/0 [kernel.kallsyms] [k] do_csum
3.23% swapper [kernel.kallsyms] [k] _raw_spin_unlock_irq
2.87% netperf [kernel.kallsyms] [k] __arch_copy_to_user
2.86% swapper [kernel.kallsyms] [k] arch_cpu_idle
2.13% swapper [kernel.kallsyms] [k] default_idle_call
2.12% ksoftirqd/0 [kernel.kallsyms] [k] sh_eth_poll
2.02% swapper [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore
1.84% swapper [kernel.kallsyms] [k] __softirqentry_text_start
1.64% swapper [kernel.kallsyms] [k] tick_nohz_idle_exit
1.53% netperf [kernel.kallsyms] [k] _raw_spin_unlock_irq
1.32% netperf [kernel.kallsyms] [k] preempt_count_sub
1.27% swapper [kernel.kallsyms] [k] __pi___inval_dcache_area
1.22% swapper [kernel.kallsyms] [k] check_preemption_disabled
1.01% ksoftirqd/0 [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore
The above results collected on the R-Car V3H Starter Kit board.
Based on the commit 4d86d3818627 ("ravb: RX checksum offload")...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 62e04b7e0e3c ("sh_eth: rename 'sh_eth_cpu_data::hw_crc'") renamed
the field to 'hw_checksum' for the Ether DMAC "intelligent checksum",
however some Ether MACs implement a simpler checksumming scheme, so that
name now seems misleading. Rename that field to 'csmr' as the "intelligent
checksum" is always controlled by the CSMR register.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace magic numbers with proper constants. The original patch is
from Andrew, I extended / adjusted certain parts:
- Use decimal bit numbers. The datasheet uses hex bit numbers 0 .. F.
- Order defines from highest to lowest bit numbers
- correct some typos
- add constant MDIO_AN_TX_VEND_INT_MASK2_LINK
- Remove few functional improvements from the patch, they will come as
a separate patch.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of macro PHY_ID_MATCH_MODEL to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unneeded header includes.
v2:
- leave kernel.h in
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aquantia_ as a name space prefix is rather long, resulting in lots of
lines needing wrapping, reducing readability. Use the prefix aqr_
instead, which fits with the vendor naming there devices aqr107, for
example.
v2:
- add SoB from Heiner
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shared buffer allocation is usually done in cell increments.
Drivers will either round up the allocation or refuse the
configuration if it's not an exact multiple of cell size.
Drivers know exactly the cell size of shared buffer, so help
out users by providing this information in dumps.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
{t4/t4_vf}_change_mac() API's were only doing additions to MPS_TCAM.
This will fail, when the number of tcam entries is limited particularly
in vf's.
This fix programs hash region with the mac address, when TCAM
addtion fails for {t4/t4vf}_change_mac(). Since the locally maintained
driver list for hash entries is shared across mac_{sync/unsync}(),
added an extra parameter if_mac to track the address added thorugh
{t4/t4vf}_change_mac()
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The integrated PHY's of later RTL8168 network chips report the generic
PHYID 0x001cc800 (Realtek OUI, model and revision number both set to
zero) and therefore currently the genphy driver is used.
To be able to use the paged version of e.g. phy_write() we need a
PHY driver with the read_page and write_page callbacks implemented.
So basically make a copy of the genphy driver, just with the
read_page and write_page callbacks being set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A return statment is not indented correctly, fix this by adding an
extra tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An if statement is indented one level too deep, fix this by removing
the extra tabs. Also add some spaces to the dev_warn arguments to clean
up checkpatch warnings.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to bfa_ioc_pf_failed is indented too far, fix this by
removing a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The assignment to size is indented too far, fix this and join
two lines into one.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA engine is a separate entity altogether, and this allows the DMA
controller's address to float elsewhere in the FPGA's map.
Signed-off-by: Alex Williams <alex.williams@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl_wol_pll_power_down() is used in only one place and removing it
makes the code simpler and better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When updating the available MAC VLAN table counts,
MAC VLAN table entry count function adds
operation 0 value protection measures.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to prevent the variable anomaly from being larger than desc_num,
the upper limit judgment condition becomes >=.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user disables vlan filter, and adds vlan device, it won't
notify the driver the update the vlan filter. In this case, when
user enables vlan filter again, the packets with new vlan tag
will be filtered by vlan filter.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple macros with the largest number of TCs in the system,
optimized to HCLGE_MAX_TC_NUM.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Run ethtool ethx when displaying device information in VF，
the supported port and link mode items will be empty.
This patch fixes it.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the TC is enabled, we need to check whether the buffer is enough,
otherwise it may lead to a wrong -ENOMEM case.
Fixes: 9ffe79a9c2ee ("net: hns3: Support for dynamically assigning tx buffer to TC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does not change the code logic. There are some same
set_bit statements called by add/rm_uc/mc_addr_common, and move
this statements into hclge_prepare_mac_addr to reduce duplicate
code.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For simplifying the code, this patch adds hclge_cmd_check_retval() to
check the return value of the command.
Also, according the IMP's description, when there are several descriptors
in a command, then the IMP will save the return value on the last
description, so hclge_cmd_check_retval() just check the last one for this
case.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are four steps to calcuate the rx private buffer, each step
can be done in a function to avoid code duplication and aid code
readability.
This patch adds three separate functions do the job. Also, the
function name more or less make the comment redundant, so remove
some obvious comment.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The second parameter to the hook function set_gro_en is always passed in
true/false, so modify it's type from int to bool.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 supports setting rx-usecs|tx-usecs as 0, but it will not
update dynamically when adaptive-tx or adaptive-rx is enable.
This patch removes the Redundant check.
Fixes: a95e1f8666e9 ("net: hns3: change the time interval of int_gl calculating")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the same code style for rx_group and tx_group in the
hns3_update_new_int_gl().
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2019-02-01
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) introduce bpf_spin_lock, from Alexei.
2) convert xdp samples to libbpf, from Maciej.
3) skip verifier tests for unsupported program/map types, from Stanislav.
4) powerpc64 JIT support for BTF line info, from Sandipan.
5) assorted fixed, from Valdis, Jesper, Jiong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The following ALU32 logic shift supports are missing:
BPF_ALU | BPF_LSH | BPF_X
BPF_ALU | BPF_RSH | BPF_X
BPF_ALU | BPF_RSH | BPF_K
For BPF_RSH | BPF_K, it could be implemented using NFP direct shift
instruction. For the other BPF_X shifts, NFP indirect shifts sequences need
to be used.
Separate code-gen hook is assigned to each instruction to make the
implementation clear.
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Shifts by zero do nothing, and should be treated as nops.
Even though compiler is not supposed to generate such instructions and
manual written assembly is unlikely to have them, but they are legal
instructions and have defined behavior.
This patch correct existing shifts code-gen to make sure they do nothing
when shift amount is zero except when the instruction is ALU32 for which
high bits need to be cleared.
For shift amount bigger than type size, already, NFP JIT back-end errors
out for immediate shift and only low 5 bits will be taken into account for
indirect shift which is the same as x86.
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
