IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Reuse OMAP4 operations on AM43x.
Context related ops are not used on AM43x, as this would not add value
when using DT and AM43x is DT only boot. This additionally helps not to
add context register offset for each hwmod.
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add hwmod support for IP's that are present in AM43x, but not in AM335x.
AM43x additional ones added here are,
1. synctimer
2. timer8-11
3. ehrpwm3-5
4. spi2-4
5. gpio4-5
AM43x pruss interconnect which is different as compared to AM335x, has
been taken care.
And register offsets for same hwmod's shared with AM335x is different,
AM43x register offsets are updated appropriately.
ocp clock of those in l4_wkup is fed from "sys_clkin_ck" instead of
"dpll_core_m4_div2_ck", so "ocpif" for those in AM43x l4_wkup has been
added seperately.
hwmod's has been added for those that have main clock (wkup_m3, control,
gpio0) and clock domain (l4_hs) different from AM335x. debugss and
adc_tsc that have different clocks and clockdomains repectively has not
been added due to the reasons mentioned below.
AM43x also has IP's like qspi, hdq1w, vpfe, des, rng, usb, dss, debugss,
adc_tsc. These are not handled here due to both/either of following
reasons,
1. To avoid churn; most of them don't have DT bindings, which would
necessitate adding address space in hwmod, which any way would have
to be removed once DT bindings happen with driver support.
2. patches would come in from sources other than the author
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the data file to describe clock domains in AM43x SoC.
OMAP4 clockdomain operations is being reused here.
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the data file to describe all power domains in AM43x SoC.
OMAP4 powerdomain operations is being reused here.
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Hwmod common to AM43x and AM335x has register offsets different. It is
now updated based on SoC detection at run time, hence remove statically
initialized ones.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Most of IP's in AM335x is present on AM43x and so in those cases both
will use same hwmod database (except for a few cases where clock related
details differ), but there is difference w.r.t register offset between
these. Update register offsets at runtime based on the SoC detected to
help in sharing otherwise same hwmod.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
AM335x and AM43x have most of the IP's and interconnect's similar.
Instead of adding redundant hwmod data, move interconnects and hwmod
similar between AM335x and AM43x to a common location. This helps in
reuse on AM43x.
AM335x interconnects that has difference and not present in AM43x are
not moved. ocp clock of those in l4_wkup is fed from a different source
for AM43x. Also pruss interconnect is different.
AM335x hwmod's that has difference other than prcm register offsets
(difference is in clocks of wkup_m3, control, gpio0, debugss and clock
domain of l4_hs, adc_tsc as compared to AM43x) and those that are not
present in AM43x are not moved.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Most of the AM43x CM reg address offsets are with MSB bit '1' (on
16-bit value) leading to arithmetic miscalculations while calculating
CLOCK ENABLE register's address because cm_inst field was a type of
"const s16", so make it "const u16".
Also modify relevant functions so as to take care of the above.
[afzal@ti.com: fixup and cleanup]
Signed-off-by: Ankur Kishore <a-kishore@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Otherwise we can get an error with some configs:
arch/arm/mach-omap2/timer.c:73: undefined reference to `omap_smc1'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add this hwmod data to allow USB3 to work in OMAP5 boards.
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated to apply against Paul's changes]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Just initialize things using the bootloader timings like
we've been doing for the legacy booting too. It should be
possible to patch in the GPMC timings for the based on the
TL16CP743C/TL16C754C manual at:
http://www.ti.com/lit/ds/slls644g/slls644g.pdf
Signed-off-by: Tony Lindgren <tony@atomide.com>
As the wl12xx bindings are still pending, this way we can
get things working for omap3 evm and zoom platforms.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now pinctrl-single-omap can handle the wake-up events for us now
as long as the events are configured in the .dts files.
Done in collaboration with Roger Quadros <rogerq@ti.com>.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Prakash Manjunathappa <prakash.pm@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For few things we're still going to be needing platform
data for device tree based drivers. Let's set up auxdata
handling and do it in pdata-quirks.c so we have all the
legacy calls in one place.
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The realtime counter called master counter, produces the count
used by the private timer peripherals in the MPU_CLUSTER. The
CNTFRQ per cpu register is used to denote the frequency of the counter.
Currently the frequency value is passed from the
DT file, but this is not scalable when we have other non-DT guest
OS. This register must be set to the right value by the
secure rom code. Setting this register helps in propagating the right
frequency value across OSes.
More discussions and the reason for adding this in a non-DT
way can be seen from below.
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg93832.html
So configuring this secure register for all the cpus here.
Cc: Nishanth Menon <nm@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that display information and setup is made from dss-common
there is no need to have this code in the board file.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
IGEPv2 board has both an DVI and TFP410 video interfaces but
DSS support for DeviceTree has not yet landed in mainline so
is necessary to init the displays using legacy platform code.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we have DT bindings to specify which devices should not
be reset and idled during init, make hwmod extract the information
(and store them in internal flags) from Device tree.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For modules/IPs/hwmods which do not have
-1- sys->class->reset()
and
-2- hardreset lines
and
-3- No way to do an ocp reset (no sysc control)
the flag 'HWMOD_INIT_NO_RESET' is not much useful.
Cleanup all such instances across various hwmod data files.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the missing sysc configuration to the AM335 spinlock hwmod
data. This ensures that smart-idle is enabled whenever the module
is enabled by the driver.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the hwmod data for the spinlock IP in OMAP5 SoC.
This is needed to be able to enable the OMAP spinlock
support for OMAP5.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add hwmod data for High Speed USB host and TLL modules
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds Synchronous Serial Interface (SSI) hwmod support for
OMAP34xx SoCs.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The hwmod init sequence involves initializing and idling all the
hwmods during bootup. If a module class has sysconfig, the init
sequence utilizes the module register base for performing any
sysc configuration.
The module address space is being removed from hwmod database and
retrieved from the <reg> property of the corresponding DT node.
If a hwmod does not have its corresponding DT node defined and the
memory address space is not defined in the corresponding
omap_hwmod_ocp_if, then the module register target address space
would be NULL and any sysc programming would result in a NULL
pointer dereference and a kernel boot hang.
Handle this scenario by checking for a valid module address space
during the _init of each hwmod, and leaving it in the registered
state if no module register address base is defined in either of
the hwmod data or the DT data.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: use -ENXIO rather than -ENOMEM to indicate a missing address
space error; fixed checkpatch.pl problem]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP5 ES1.0 was intended as a test chip and has major register level
differences w.r.t ES2.0 revision of the chip. All register defines,
dts support has been solely added for ES2.0 version of the chip.
Further, all ES1.0 chips and platforms are supposed to have been
removed from circulation. Hence, there is no need to further retain
any resemblence of ES1.0 support in id detection code.
Remove the omap_revision handling and BUG() instead to prevent folks
who mistakenly try an older unsupported chip and report bogus errors.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The real time counter also called master counter, is a free-running
counter. It produces the count used by the CPU local timer peripherals
in the MPU cluster. The timer counts at a rate of 6.144 MHz.
The ratio registers are missing for a sys-clk of 20MHZ which is used
by DRA7 socs. So because of this, the counter was getting wrongly
programmed for a sys-clk of 38.4Mhz(default). So adding the ratio
registers for 20MHZ sys-clk.
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move omap_vout device creation inside the omap_display_init so that we can
correctly create the device based on the presence of omapdss within the
platform.
For example, on a kernel image supporting multiple platforms, omap_init_vout
will create a omapdrm platform device on a AM33xx platform even though it
doesn't have a DSS block.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move omapfb and omapvrfb device creation inside the omap_display_init so that
we can correctly create the device based on the presence of omapdss within the
platform.
For example, on a kernel image supporting multiple platforms, omap_init_vrfb and
omap_init_fb will create omapvrfb and omapfb platform devices respectively on a
AM33xx platform even though it doesn't have a VRFB or DSS block.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move omapdrm device creation inside the omap_display_init so that we can
correctly create the device based on the presence of omapdss within the
platform.
For example, on a kernel image supporting multiple platforms, omap_init_drm
will create a omapdrm platform device on a AM33xx platform even though it
doesn't have a DSS block.
Originally worked on by Andy Gross.
Cc: Andy Gross <andygro@gmail.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DMM exists on omap4+ platforms, these platforms are always expected to boot with
DT. Remove the current method of searching the dmm hwmod and building an
omap_device for dmm.
For OMAP4, the address and irq data for DMM hwmod(along with other blocks) were
removed, so the current method fails in the dmm driver's probe anyway.
The addition of DMM nodes in DT will ensure that a DMM device is built
correctly.
Cc: Andy Gross <andygro@gmail.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding this driver as platform device and only for RX-51 until somebody test if
it working also on other OMAP3 HS devices and until there will be generic ARM
way to deal with SMC calls.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
[tony@atomide.com: folded in the clock alias change]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Closed and signed Nokia X-Loader bootloader stored in RX-51 nand does not set
IBE bit in ACTLR and starting kernel in non-secure mode. So direct write to
ACTLR by our kernel does not working and the code for ARM errata 430973 in
commit 7ce236fcd6fd45b0441a2d49acb2ceb2de2e8a47 that sets IBE bit is a noop.
In order to have workaround for ARM errata 430973 from non-secure world on
RX-51 we needs Secure Monitor Call to set IBE BIT in ACTLR.
This patch adds RX-51 specific secure support code and sets IBE bit in ACTLR
during board init code for ARM errata 430973 workaround.
Note that new function rx51_secure_dispatcher() differs from existing
omap_secure_dispatcher(). It calling omap_smc3() and param[0] is nargs+1.
ARM errata 430973 workaround is needed for thumb-2 ISA compiled userspace
binaries. Without this workaround thumb-2 binaries crashing. So with this
patch it is possible to recompile and run applications/binaries with thumb-2
ISA on RX-51.
Signed-off-by: Ivaylo Dimitrov <freemangordon@abv.bg>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Here is new version (v4) of omap secure part patch:
Other secure functions omap_smc1() and omap_smc2() calling instruction smc #0
but Nokia RX-51 board needs to call smc #1 for PPA access.
Signed-off-by: Ivaylo Dimitrov <freemangordon@abv.bg>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
File drivers/leds/leds-lp55xx-common.c refuse to change led_current sysfs
attribute if value is higher than max_current specified in board file. By default
global C variables are zero, so changing always failed. This patch adding missing
max_current and setting it to max safe value 100 (10 mA).
It is unclear which commit exactly caused this regression as the lp5523
driver was broken and was hiding the platform data breakage. Now
the driver is fixed so this should be fixed as well.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Joerg Reisenweber <joerg@openmoko.org>
[tony@atomide.com: updated comments to describe regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since dra7 reuses the function 'omap5_realtime_timer_init' in
arch/arm/mach-omap2/board-generic.c as timer init function, it has to be
built for this SoC as well.
Signed-off-by: Simon Barth <Simon.Pe.Barth@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The wake-up interrupt bit is available on omap3/4/5 processors
unlike what we claim. Without fixing it we cannot use it on
omap3 and the system configured for wake-up events will just
hang on wake-up.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
SoC family definitions at the moment are reactive to board needs
as a result, beagle-xm would matchup with ti,omap3 which invokes
omap3430_init_early instead of omap3630_init_early. Obviously, this is
the wrong behavior.
With clock node dts conversion, we get the following warnings before
system hangs as a result and 3630 based platforms fails to boot
(uart4 clocks are only present in OMAP3630 and not present in
OMAP3430):
...
omap_hwmod: uart4: cannot clk_get main_clk uart4_fck
omap_hwmod: uart4: cannot _init_clocks
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2434
_init+0x6c/0x80()
omap_hwmod: uart4: couldn't init clocks
...
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: timer12: enabled state can only be entered from
initialized, idle, or disabled state
...
WARNING: CPU: 0 PID: 46 at arch/arm/mach-omap2/omap_hwmod.c:2224
_idle+0xd4/0xf8()
omap_hwmod: timer12: idle state can only be entered from enabled state
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: uart4: enabled state can only be entered from
initialized, idle, or disabled state
So, add specific compatiblity for 3630 to allow match for Beagle-XM
platform.
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: left out ti,omap343x, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
CLKDEV_LOOKUP selects HAVE_CLK and COMMON_CLK selects CLKDEV_LOOKUP. So
all symbols that select at least two of these symbols can be simplified.
For imx, omap2 and ux500 some rearrangements were necessary before the
simplification.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
The USB phy-nop nop driver expects the RESET line information
to be sent as a GPIO number via platform data. Adapt to that.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The platform data bits can be inferred from the other members of
struct usbhs_phy_data. So get rid of the platform_data member.
Build the platform data for the PHY device in usbhs_init_phys() instead.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch proposes to remove the IRQF_DISABLED flag from OMAP code
It's a NOOP since 2.6.35, and will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
At least eight bytes of this number are totally unique for the device
it seems, so this is a perfect candidate for feeding the entropy
pool. One byte more or less of constants does not matter so feed in
the entire OID struct.
This fixes the issue of similar devices initializing to the
same state initially.
Further registers could be added too, such as OMAP4
CONTROL_STD_FUSE_OPP* and CONTROL_DPLL_NWELL_TRIM* registers,
but those vary based on the SoC generation.
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[tony@atomide.com: updated comments per mailing list discussion]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves the at24.h header from include/linux/i2c to
include/linux/platform_data and updates existing support accordingly.
It also fixes the following checkpatch warning:
WARNING: please, no space before tabs
#436: FILE: include/linux/platform_data/at24.h:31:
+ * ^Iu8 *mac_addr = ethernet_pdata->mac_addr;$
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The PHY framework uses the phy consumer data populated in platform data in the
case of non-dt boot to return the reference to the PHY when the controller
(PHY consumer) requests for it. So populated the phy consumer data in the platform
data of twl usb.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's use the platform data quirk support for wl12xx
and move the board specific code out of devices.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>
