IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
Here is the big char/misc driver update for 4.6-rc1.
The majority of the patches here is hwtracing and some new mic drivers,
but there's a lot of other driver updates as well. Full details in the
shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbp9IcACgkQMUfUDdst+ykyJgCeLTC2QNGrh51kiJglkVJ0yD36
q4MAn0NkvSX2+iv5Jq8MaX6UQoRa4Nun
=MNjR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big char/misc driver update for 4.6-rc1.
The majority of the patches here is hwtracing and some new mic
drivers, but there's a lot of other driver updates as well. Full
details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (238 commits)
goldfish: Fix build error of missing ioremap on UM
nvmem: mediatek: Fix later provider initialization
nvmem: imx-ocotp: Fix return value of imx_ocotp_read
nvmem: Fix dependencies for !HAS_IOMEM archs
char: genrtc: replace blacklist with whitelist
drivers/hwtracing: make coresight-etm-perf.c explicitly non-modular
drivers: char: mem: fix IS_ERROR_VALUE usage
char: xillybus: Fix internal data structure initialization
pch_phub: return -ENODATA if ROM can't be mapped
Drivers: hv: vmbus: Support kexec on ws2012 r2 and above
Drivers: hv: vmbus: Support handling messages on multiple CPUs
Drivers: hv: utils: Remove util transport handler from list if registration fails
Drivers: hv: util: Pass the channel information during the init call
Drivers: hv: vmbus: avoid unneeded compiler optimizations in vmbus_wait_for_unload()
Drivers: hv: vmbus: remove code duplication in message handling
Drivers: hv: vmbus: avoid wait_for_completion() on crash
Drivers: hv: vmbus: don't loose HVMSG_TIMER_EXPIRED messages
misc: at24: replace memory_accessor with nvmem_device_read
eeprom: 93xx46: extend driver to plug into the NVMEM framework
eeprom: at25: extend driver to plug into the NVMEM framework
...
* add types for USB Type C and PD chargers
* add act8945a charger driver
* add ACPI/DT bindings for goldfish-battery
* add support for versatile reset controller
* misc. fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=L4ho
-----END PGP SIGNATURE-----
Merge tag 'for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset changes from Sebastian Reichel:
- add types for USB Type C and PD chargers
- add act8945a charger driver
- add ACPI/DT bindings for goldfish-battery
- add support for versatile reset controller
- misc fixes
* tag 'for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (24 commits)
power: pm2301-charger: use __maybe_unused to hide pm functions
power: ipaq-micro-battery: use __maybe_unused to hide pm functions
power_supply: 88pm860x_charger: do not pass NULL to power_supply_put
jz4740-battery: Correct voltage change check
power_supply: lp8788-charger: initialize boolean 'found'
goldfish: Enable ACPI-based enumeration for goldfish battery
power: goldfish_battery: add devicetree bindings
power: act8945a: add charger driver for ACT8945A
power: add documentation for ACT8945A's charger DT bindings
ARM: dts: n900: Rename isp1704 to isp1707 to match correct name
power_supply: bq27xxx_battery: Add of modalias and match table when CONFIG_OF is enabled
power_supply: bq2415x_charger: Add of modalias and match table when CONFIG_OF is enabled
power_supply: bq2415x_charger: Do not add acpi modalias when CONFIG_ACPI is not enabled
power_supply: isp1704_charger: Add compatible of match for nxp,isp1707
power_supply: isp1704_charger: Error messages when probe fail
power_supply: Add types for USB Type C and PD chargers
power: bq24735-charger: add 'ti,external-control' option
power: bq24735-charger: document 'ti,external-control' option
power: bq24735-charger: fix failed i2c with ac-detect
power: reset: Fix dependencies for !HAS_IOMEM archs
...
This patch adds the emac device node for rk3036 SoCs.
We need to let mac clock under the DPLL which is able to provide
the accurate 50MHz what mac_ref need, since that will cause some
unstable things if the cpufreq is working.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: linux-rockchip@lists.infradead.org
Cc: Xing Zheng <zhengxing@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
- New drivers for NSA320 and LTC2990
- Added support for ADM1278 to adm1275 driver
- Added support for ncpXXxh103 to ntc_thermistor driver
- Renamed vexpress hwmon implementation
- Minor cleanups and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=n07O
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- New drivers for NSA320 and LTC2990
- Added support for ADM1278 to adm1275 driver
- Added support for ncpXXxh103 to ntc_thermistor driver
- Renamed vexpress hwmon implementation
- Minor cleanups and improvements
* tag 'hwmon-for-linus-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: Create an NSA320 hardware monitoring driver
hwmon: Define binding for the nsa320-hwmon driver
hwmon: (adm1275) Add support for ADM1278
hwmon: (ntc_thermistor) Add support for ncpXXxh103
Doc: hwmon: Fix typo "montoring" in hwmon
ARM: dts: vfxxx: Add iio_hwmon node for ADC temperature channel
ARM: dts: Change iio_hwmon nodes to use hypen in node names
hwmon: (iio_hwmon) Allow the driver to accept hypen in device tree node names
hwmon: Add LTC2990 sensor driver
hwmon: (vexpress) rename vexpress hwmon implementation
An almost purely driver related set of changes with no
major changes to the framework, only one patch adding
an unlocked version of the pinctrl_find_gpio_range_from_pin()
library call.
New drivers:
- ST Microelectronics STM32 MCU support: this is a non-MMU
low-end platform for IoT things (etc).
- Microchip PIC32 MCU support: same story as for STM32.
New subdrivers:
- Allwinner SunXi H3 R_PIO controller support.
- Qualcomm IPQ4019 support.
- MediaTek MT2701 and MT7623.
- Allwinner A64
Non-critical fixes:
- gpio_disable_free() for the Vybrid.
- pinctrl single: use a separate lockdep class.
Misc:
- Substantial cleanups and rewrites for the Super-H PFC
driver and subdrivers.
- Various fixes and cleanups, especially Paul Gortmakers
work to make nonmodular drivers nonmodular.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJW5rS1AAoJEEEQszewGV1zskIQALNriHdVmPGNIuSZOUk2gqAv
hFNIzFUYM6BK6AL2wD+ZVqQe/EbZtWUF2RqhI2juP8j2WBVMxo8B9ypGjm8qDZ7q
Xtdnd8l22VP0fEmYKTwDgrjSCcMxbXFiPurZBlqCCyb/9raFqLKwx2kcxWqD4PR2
dcC8i/t2JSjGYRRCMcGn+zcKW2zja36xci/ZOExdioHYgFmorCZb9+4NYz+coijv
VEjEy98CG6itBFJ0MS3jHT949TyxpDzWp7hO8LiOAiLR50xCxTlZRT1dObOUQJqk
qhiLK2sTUFJFlTNBUGN0gfMoJo2MpfJIkVre4EV5QNkfy8vjtXeLrbjnSnTXf0r7
5OLMEJPK7mfHd7jsw/nwJMYUoqgeRO9VBXtL2JyGWpsNFBFlJv1YRXaT0AZXkgUq
63BfhTrbtge2xECJ9iqWVdGmmNv2x7lMK6RWqDr72fjONdtmNLDusfNdgYaBWc50
K910IijMX2t2HGQFzuqwQC5HgADPhqBRb2eMcilwwUs5rxzLXX/wer1rhc8guUtK
4DvGZ+wPZd2znQvNAWxsG5azoSfO8J3ibVIkMmaW3NTqyLvnbT9KiNvYuUVg/9NQ
Vcb1d9UnrhAIWzpfpeo4rzr+QIq4j46YHBqreiW/l952Apxpp2lJmV/btK0noPmA
MDTknHc2772QYIBtn01D
=TsdU
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"An almost purely driver related set of changes with no major changes
to the framework, only one patch adding an unlocked version of the
pinctrl_find_gpio_range_from_pin() library call.
New drivers:
- ST Microelectronics STM32 MCU support: this is a non-MMU low-end
platform for IoT things (etc).
- Microchip PIC32 MCU support: same story as for STM32.
New subdrivers:
- Allwinner SunXi H3 R_PIO controller support.
- Qualcomm IPQ4019 support.
- MediaTek MT2701 and MT7623.
- Allwinner A64
Non-critical fixes:
- gpio_disable_free() for the Vybrid.
- pinctrl single: use a separate lockdep class.
Misc:
- Substantial cleanups and rewrites for the Super-H PFC driver and
subdrivers.
- Various fixes and cleanups, especially Paul Gortmakers work to make
nonmodular drivers nonmodular"
* tag 'pinctrl-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (75 commits)
pinctrl: single: Use a separate lockdep class
drivers: pinctrl: add driver for Allwinner A64 SoC
pinctrl: Broadcom Northstar2 pinctrl device tree bindings
pinctrl: amlogic: Make driver independent from two-domain configuration
pinctrl: amlogic: Separate some pin functions for Meson8 / Meson8b
pinctrl: at91: use __maybe_unused to hide pm functions
pinctrl: sh-pfc: core: don't open code of_device_get_match_data()
pinctrl: uniphier: rename CONFIG options and file names
pinctrl: sunxi: make A80 explicitly non-modular
pinctrl: stm32: make explicitly non-modular
pinctrl: sh-pfc: make explicitly non-modular
pinctrl: meson: make explicitly non-modular
pinctrl: pinctrl-mt6397 driver explicitly non-modular
pinctrl: sunxi: does not need module.h
pinctrl: pxa2xx: export symbols
pinctrl: sunxi: Change mux setting on PI irq pins
pinctrl: sunxi: Remove non existing irq's
pinctrl: imx: attach iomuxc device to gpr syscon
pinctrl-bcm2835: Fix cut-and-paste error in "pull" parsing
pinctrl: lpc1850-scu: document nxp,gpio-pin-interrupt
...
Allow Openblock AX3 using hardware buffer management with mvneta.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since mvneta driver supports using hardware buffer management (BM), in
order to use it, board files have to be adjusted accordingly. This commit
enables BM on AXP-DB and AXP-GP in same manner - because number of ports
on those boards is the same as number of possible pools, each port is
supposed to use single pool for all kind of packets.
Moreover appropriate entry is added to 'soc' node ranges, as well as "okay"
status for 'bm' and 'bm-bppi' (internal SRAM) nodes.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Armada XP network controller supports hardware buffer management (BM).
Since it is now enabled in mvneta driver, appropriate nodes can be added
to armada-xp.dtsi - for the actual common BM unit (bm@c0000) and its
internal SRAM (bm-bppi), which is used for indirect access to buffer
pointer ring residing in DRAM.
Pools - ports mapping, bm-bppi entry in 'soc' node's ranges and optional
parameters are supposed to be set in board files.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since mvneta driver supports using hardware buffer management (BM), in
order to use it, board files have to be adjusted accordingly. This commit
enables BM on:
* A385-DB-AP - each port has its own pool for long and common pool for
short packets,
* A388-ClearFog - same as above,
* A388-DB - to each port unique 'short' and 'long' pools are mapped,
* A388-GP - same as above.
Moreover appropriate entry is added to 'soc' node ranges, as well as "okay"
status for 'bm' and 'bm-bppi' (internal SRAM) nodes.
[gregory.clement@free-electrons.com: add suppport for the ClearFog board]
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Armada 38x network controller supports hardware buffer management (BM).
Since it is now enabled in mvneta driver, appropriate nodes can be added
to armada-38x.dtsi - for the actual common BM unit (bm@c8000) and its
internal SRAM (bm-bppi), which is used for indirect access to buffer
pointer ring residing in DRAM.
Pools - ports mapping, bm-bppi entry in 'soc' node's ranges and optional
parameters are supposed to be set in board files.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two more fixes for 4.5:
- One is a fix for OMAP that is urgently needed to avoid DRA7xx chips from
premature aging, by always keeping the Ethernet clock enabled.
- The other solves a I/O memory layout issue on Armada, where SROM and PCI
memory windows were conflicting in some configurations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/uWT
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Two more fixes for 4.5:
- One is a fix for OMAP that is urgently needed to avoid DRA7xx chips
from premature aging, by always keeping the Ethernet clock enabled.
- The other solves a I/O memory layout issue on Armada, where SROM
and PCI memory windows were conflicting in some configurations"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mvebu: fix overlap of Crypto SRAM with PCIe memory window
ARM: dts: dra7: do not gate cpsw clock due to errata i877
ARM: OMAP2+: hwmod: Introduce ti,no-idle dt property
When the Crypto SRAM mappings were added to the Device Tree files
describing the Armada XP boards in commit c466d997bb16 ("ARM: mvebu:
define crypto SRAM ranges for all armada-xp boards"), the fact that
those mappings were overlaping with the PCIe memory aperture was
overlooked. Due to this, we currently have for all Armada XP platforms
a situation that looks like this:
Memory mapping on Armada XP boards with internal registers at
0xf1000000:
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf8000000 -> 0xffe0000 126M PCIe memory aperture
- 0xf8100000 -> 0xf8110000 64KB Crypto SRAM #0 => OVERLAPS WITH PCIE !
- 0xf8110000 -> 0xf8120000 64KB Crypto SRAM #1 => OVERLAPS WITH PCIE !
- 0xffe00000 -> 0xfff00000 1M PCIe I/O aperture
- 0xfff0000 -> 0xffffffff 1M BootROM
The overlap means that when PCIe devices are added, depending on their
memory window needs, they might or might not be mapped into the
physical address space. Indeed, they will not be mapped if the area
allocated in the PCIe memory aperture by the PCI core overlaps with
one of the Crypto SRAM. Typically, a Intel IGB PCIe NIC that needs 8MB
of PCIe memory will see its PCIe memory window allocated from
0xf80000000 for 8MB, which overlaps with the Crypto SRAM windows. Due
to this, the PCIe window is not created, and any attempt to access the
PCIe window makes the kernel explode:
[ 3.302213] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 3.307841] pci 0000:00:09.0: enabling device (0140 -> 0143)
[ 3.313539] mvebu_mbus: cannot add window '4:f8', conflicts with another window
[ 3.320870] mvebu-pcie soc:pcie-controller: Could not create MBus window at [mem 0xf8000000-0xf87fffff]: -22
[ 3.330811] Unhandled fault: external abort on non-linefetch (0x1008) at 0xf08c0018
This problem does not occur on Armada 370 boards, because we use the
following memory mapping (for boards that have internal registers at
0xf1000000):
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0 => OK !
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
Obviously, the solution is to align the location of the Crypto SRAM
mappings of Armada XP to be similar with the ones on Armada 370, i.e
have them between the "internal registers" area and the beginning of
the PCIe aperture.
However, we have a special case with the OpenBlocks AX3-4 platform,
which has a 128 MB NOR flash. Currently, this NOR flash is mapped from
0xf0000000 to 0xf8000000. This is possible because on OpenBlocks
AX3-4, the internal registers are not at 0xf1000000. And this explains
why the Crypto SRAM mappings were not configured at the same place on
Armada XP.
Hence, the solution is two-fold:
(1) Move the NOR flash mapping on Armada XP OpenBlocks AX3-4 from
0xe8000000 to 0xf0000000. This frees the 0xf0000000 ->
0xf80000000 space.
(2) Move the Crypto SRAM mappings on Armada XP to be similar to
Armada 370 (except of course that Armada XP has two Crypto SRAM
and not one).
After this patch, the memory mapping on Armada XP boards with
registers at 0xf1 is:
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0
- 0xf1110000 -> 0xf1120000 64KB Crypto SRAM #1
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
And the memory mapping for the special case of the OpenBlocks AX3-4
(internal registers at 0xd0000000, NOR of 128 MB):
- 0x00000000 -> 0xc0000000 3G RAM
- 0xd0000000 -> 0xd1000000 1M internal registers
- 0xe800000 -> 0xf0000000 128M NOR flash
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0
- 0xf1110000 -> 0xf1120000 64KB Crypto SRAM #1
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
Fixes: c466d997bb16 ("ARM: mvebu: define crypto SRAM ranges for all armada-xp boards")
Reported-by: Phil Sutter <phil@nwl.cc>
Cc: Phil Sutter <phil@nwl.cc>
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Force the DRA7xx Ethernet internal clock source to stay enabled
per TI erratum i877:
http://www.ti.com/lit/er/sprz429h/sprz429h.pdf
Otherwise, if the Ethernet internal clock source is disabled, the
chip will age prematurely, and the RGMII I/O timing will soon
fail to meet the delay time and skew specifications for 1000Mbps
Ethernet.
This fix should go in as soon as possible.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/omap-critical-fixes-for-v4.5-rc/20160307014209/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kJw8
-----END PGP SIGNATURE-----
Merge tag 'for-v4.5-rc/omap-critical-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
ARM: OMAP2+: critical DRA7xx fix for v4.5-rc
Force the DRA7xx Ethernet internal clock source to stay enabled
per TI erratum i877:
http://www.ti.com/lit/er/sprz429h/sprz429h.pdf
Otherwise, if the Ethernet internal clock source is disabled, the
chip will age prematurely, and the RGMII I/O timing will soon
fail to meet the delay time and skew specifications for 1000Mbps
Ethernet.
This fix should go in as soon as possible.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/omap-critical-fixes-for-v4.5-rc/20160307014209/
* tag 'for-v4.5-rc/omap-critical-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: dts: dra7: do not gate cpsw clock due to errata i877
ARM: OMAP2+: hwmod: Introduce ti,no-idle dt property
Signed-off-by: Olof Johansson <olof@lixom.net>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Errata id: i877
Description:
------------
The RGMII 1000 Mbps Transmit timing is based on the output clock
(rgmiin_txc) being driven relative to the rising edge of an internal
clock and the output control/data (rgmiin_txctl/txd) being driven relative
to the falling edge of an internal clock source. If the internal clock
source is allowed to be static low (i.e., disabled) for an extended period
of time then when the clock is actually enabled the timing delta between
the rising edge and falling edge can change over the lifetime of the
device. This can result in the device switching characteristics degrading
over time, and eventually failing to meet the Data Manual Delay Time/Skew
specs.
To maintain RGMII 1000 Mbps IO Timings, SW should minimize the
duration that the Ethernet internal clock source is disabled. Note that
the device reset state for the Ethernet clock is "disabled".
Other RGMII modes (10 Mbps, 100Mbps) are not affected
Workaround:
-----------
If the SoC Ethernet interface(s) are used in RGMII mode at 1000 Mbps,
SW should minimize the time the Ethernet internal clock source is disabled
to a maximum of 200 hours in a device life cycle. This is done by enabling
the clock as early as possible in IPL (QNX) or SPL/u-boot (Linux/Android)
by setting the register CM_GMAC_CLKSTCTRL[1:0]CLKTRCTRL = 0x2:SW_WKUP.
So, do not allow to gate the cpsw clocks using ti,no-idle property in
cpsw node assuming 1000 Mbps is being used all the time. If someone does
not need 1000 Mbps and wants to gate clocks to cpsw, this property needs
to be deleted in their respective board files.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tiny fixes branch this week, in fact only one patch.
Turns out the USB support for a Renesas board was developed on a pre-release
board that ended up being changed before shipping. To avoid breakage on those
boards, and avoid confusion, it's a reasonable idea to patch now instead of
later. There are no known users of the pre-release variant any more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aA8l
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fix from Olof Johansson:
"Tiny fixes branch this week, in fact only one patch.
Turns out the USB support for a Renesas board was developed on a
pre-release board that ended up being changed before shipping. To
avoid breakage on those boards, and avoid confusion, it's a reasonable
idea to patch now instead of later. There are no known users of the
pre-release variant any more"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: porter: remove enable prop from HS-USB device node
Pull ARM fixes from Russell King:
"Just two ARM fixes this time: one to fix the hyp-stub for older ARM
CPUs, and another to fix the set_memory_xx() permission functions to
deal with zero sizes correctly"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8544/1: set_memory_xx fixes
ARM: 8534/1: virt: fix hyp-stub build for pre-ARMv7 CPUs
Add iio-hwmon node to expose the temperature channel on Vybrid as
hardware monitor device using the iio_hwmon driver.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Change iio_hwmon nodes to use hypen in node names instead of
underscore.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Detailed description for patchset:
1. Add new EXTCON_CHG_USB_SDP type
- SDP (Standard Downstream Port) USB Charging Port
means the charging connector.a
2. Add the VBUS detection by using GPIO on extcon-palmas
- Beaglex15 board uses the extcon-palmas driver
But, beaglex15 board need the GPIO support for VBUS
detection.
3. Fix the minor issue of extcon drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Zxas
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-testing
Chanwoo writes:
Update extcon for 4.6
Detailed description for patchset:
1. Add new EXTCON_CHG_USB_SDP type
- SDP (Standard Downstream Port) USB Charging Port
means the charging connector.a
2. Add the VBUS detection by using GPIO on extcon-palmas
- Beaglex15 board uses the extcon-palmas driver
But, beaglex15 board need the GPIO support for VBUS
detection.
3. Fix the minor issue of extcon drivers
In the final versions of the Porter board (called "PORTER_C") Renesas
decided to get rid of the Maxim Integrated MAX3355 OTG chip and didn't
add any other provision to differ the host/gadget mode, so we'll have to
remove no longer valid "renesas,enable-gpio" property from the HS-USB
device node. Hopefully, the earlier revisions of the board were never
seen in the wild...
Fixes: c794f6a09a25 ("ARM: shmobile: porter: add HS-USB DT support")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the 1588 timer node for ls1021a platform to
support gianfar ptp driver.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Yet another fix for n900 onenand to avoid corruption. This time to
fix the issue of mounting onenand back and forth between the original
maemo kernel and mainline Linux kernel. And it also seems there will
be two more fixes coming via the MTD tree as issues were discovered
also in the onenand driver during testing.
- Revert tps65217 regulator clean up as it breaks MMC for am335x
variants. The proper way to clean this up is just to rename the
tps65217.dtsi file into tps65217-am335x.dtsi as a similar setup
is used on many am335x boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tAiy
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Two omap fixes for omaps against v4.5-rc5:
- Yet another fix for n900 onenand to avoid corruption. This time to
fix the issue of mounting onenand back and forth between the original
maemo kernel and mainline Linux kernel. And it also seems there will
be two more fixes coming via the MTD tree as issues were discovered
also in the onenand driver during testing.
- Revert tps65217 regulator clean up as it breaks MMC for am335x
variants. The proper way to clean this up is just to rename the
tps65217.dtsi file into tps65217-am335x.dtsi as a similar setup
is used on many am335x boards.
* tag 'omap-for-v4.5/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix onenand initialization to avoid filesystem corruption
Revert "regulator: tps65217: remove tps65217.dtsi file"
Signed-off-by: Olof Johansson <olof@lixom.net>
PIN_PA15 macro has the same value as PIN_PA14 so we were overriding PA14
mux/configuration.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reported-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: 7f16cb676c00 ("ARM: at91/dt: add sama5d2 pinmux")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Drop the bogus interrupt-parent from i.MX6 CAAM node, which leads to
the CAAM IRQs not getting unmasked at the GPC level.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWwEEWAAoJEFBXWFqHsHzOvv4H/29Q3aZBN/L/0JzPyCckfWSw
/l2UGsFW5UIBPbrOPW9tEPd4WRAUQ3BJKM2iNvvSSeNMvEO/Ni1+CtzQabCv7CGb
sKRZOIQ8e8782K4aNmCMMwrVBhPMAewFuh4DkCDdN55sE5kN9CkDO0d6jzaHsDJf
8GnuT5kq6qblV1HdsdVnEBjwL73v3wByUhUN3T6BplM4l9GtRRu7ox6s3dDdM4jG
ohBRafPo0s+pMOI8LRs7howHQwAuSHCMP7zOzqCOwvSAa+GOwKIjpQFvAKU+mfex
h+c2bdNxSCkDPG/QBwfk723qRWrDND0hMetHGNFn1zh8s0HhBzp7bNXKnLC5JF8=
=9ONj
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for v4.5:
- Drop the bogus interrupt-parent from i.MX6 CAAM node, which leads to
the CAAM IRQs not getting unmasked at the GPC level.
* tag 'imx-fixes-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6: remove bogus interrupt-parent from CAAM node
Signed-off-by: Olof Johansson <olof@lixom.net>
- Improve omap_device error message to tell driver writers what is
wrong after commit 5de85b9d57ab ("PM / runtime: Re-init runtime PM
states at probe error and driver unbind"). There will be also a
handful of driver related fixes also queued separately. But adding
this error message makes it easy to fix any omap_device using
drivers suffering from this issue so I think it's important to
have.
- Also related to commit 5de85b9d57ab discussion, let's fix a bug
where disabling PM runtime via sysfs will also cause the hardware
state to be different from PM runtime state.
- Fix audio clocks for beagle-x15.
- Use wakeup-source instead of gpio-key,wakeup for the new entries
that sneaked in during the merge window.
- Fix a legacy booting vs device tree based booting regression for
n900 where the legacy user space expects to have the device
revision available in /proc/atags also when booted with device
tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1rk2
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/fixes-rc3-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Few fixes for omaps against v4.5-rc3:
- Improve omap_device error message to tell driver writers what is
wrong after commit 5de85b9d57ab ("PM / runtime: Re-init runtime PM
states at probe error and driver unbind"). There will be also a
handful of driver related fixes also queued separately. But adding
this error message makes it easy to fix any omap_device using
drivers suffering from this issue so I think it's important to
have.
- Also related to commit 5de85b9d57ab discussion, let's fix a bug
where disabling PM runtime via sysfs will also cause the hardware
state to be different from PM runtime state.
- Fix audio clocks for beagle-x15.
- Use wakeup-source instead of gpio-key,wakeup for the new entries
that sneaked in during the merge window.
- Fix a legacy booting vs device tree based booting regression for
n900 where the legacy user space expects to have the device
revision available in /proc/atags also when booted with device
tree.
* tag 'omap-for-v4.5/fixes-rc3-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix omap_device for module reload on PM runtime forbid
ARM: OMAP2+: Improve omap_device error for driver writers
ARM: DTS: am57xx-beagle-x15: Select SYS_CLK2 for audio clocks
ARM: dts: am335x/am57xx: replace gpio-key,wakeup with wakeup-source property
ARM: OMAP2+: Set system_rev from ATAGS for n900
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu fixes for 4.5 (part 2)
- Fix the missing mtd flash on linkstation lswtgl
- Use unique machine name for the kirkwood ds112 (for Debian flash-kernel tool)
* tag 'mvebu-fixes-4.5-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: orion5x: fix the missing mtd flash on linkstation lswtgl
ARM: dts: kirkwood: use unique machine name for ds112
Signed-off-by: Olof Johansson <olof@lixom.net>
This change does not break existing userspace or Maemo software because
isp1704_charger.c always export power supply device under isp1704 name.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
ARMv6 CPUs do not have virtualisation extensions, but hyp-stub.S is
still included into the image to keep it generic. In order to use ARMv7
instructions during HYP initialisation, add -march=armv7-a flag to
hyp-stub's build.
On an ARMv6 CPU, __hyp_stub_install returns as soon as it detects that
the mode isn't HYP, so we will never reach those instructions.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 8e6ebfaa9b384088002baa10f7534efa73a0794e.
Without the patch reverted regulators will not work. This prevents
MMC to be working for example so the boards can not boot to
MMC rootfs.
Tested it on beaglebone white and bisect also points to the
reverted commit.
The issue can be also fixed by adding "regulator-compatible =" to all board
dts file for the regulators.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The tlv320aic3104 codec's master clock is coming from the SoC's CLKOUT2.
Select the SYS_CLK2 (via divider) as parent clock for CLKOUT2 and select
the same clock (SYS_CLK2) for McASP3 AHCLKX clock as well.
SYS_CLK2 is sourced from an external oscillator running 22.5792MHz and it
is coming in to the SoC via the X1_OSC1.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 3efda00129bd ("ARM: dts: am335x: replace gpio-key,wakeup with
wakeup-source property") replaces all the legacy "gpio-key,wakeup" with
the unified "wakeup-source" property to prevent any further copy-paste
duplication.
However couple of use of these legacy property sneaked in during the
merge window. This patch replaces them too.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MTD flash stores u-boot and u-boot environment on linkstation lswtgl.
The latter one can be easily read/write by u-boot-tools package in Debian.
Fixes: dc57844a736f ("ARM: dts: orion5x: add buffalo linkstation ls-wtgl")
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Downstream packages like Debian flash-kernel use
/proc/device-tree/model
to determine which dtb file to install.
Hence each dts in the Linux kernel should provide a unique model
identifier.
Commit 2d0a7addbd10 ("ARM: Kirkwood: Add support for many Synology NAS
devices") created the new files kirkwood-ds111.dts and kirkwood-ds112.dts
using the same model identifier.
This patch provides a unique model identifier for the
Synology DiskStation DS112.
Fixes: 2d0a7addbd10 ("ARM: Kirkwood: Add support for many Synology NAS devices")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
According to latest schematics [1], GPIO_1/VBUSDET
on TPS659038 is tied to AM57x GPIO4_21. We can use
that as a VBUS interrupt, instead of relying on
PMIC's VBUS interrupts which don't seem to be firing
on x15 at all.
A follow up patch will add support for using this
GPIO-based interrupt mechanism for notifying about
VBUS.
[1] https://github.com/beagleboard/beagleboard-x15/blob/master/BeagleBoard-X15_RevA2.pdf
Signed-off-by: Felipe Balbi <balbi@ti.com>
[cw00.choi: Use the 'vbus-gpio' property instead of 'interrupts-extended']
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
According to latest schematics [1], this board
leaves ID pin floating. It's not connected to
anything at all.
So let's remove it.
[1] https://github.com/beagleboard/beagleboard-x15/blob/master/BeagleBoard-X15_RevA2.pdf
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The DTSI file for the Nomadik does not properly specify how the
PL180 levelshifter is connected: the Nomadik actually needs all
the five st,sig-dir-* flags set to properly control all lines out.
Further this board supports full power cycling of the card, and
since this variant has no hardware clock gating, it needs a
ridiculously low frequency setting to keep up with the ever
overflowing FIFO.
The pin configuration set-up is a bit of a mystery, because of
course these pins are a mix of inputs and outputs. However the
reference implementation sets all pins to "output" with
unspecified initial value, so let's do that here as well.
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
assembly fixes, the other things are mostly board related:
- A series of omap assembly code fixes to fix issues with rodata with
ARM_KERNMEM_PERMS enabled. We had several places writing to rodata,
which is bad. The fix in most cases is to load the value from data
section using a pointer. Let's also enable ARM_KERNMEM_PERMS so
DEBUG_RODATA gets selected by default. And while testing things,
I also added few more loadable driver modules to the defconfig that
I seem to need quite often.
- Fix a long standing omap5 RTC mystery and enable RTC where we need
to ensure the SoC msecure pin is high so we can write to the RTC
registers.
- Fix irq types for am437x
- A series of minor dts fixes for sbc-am57x and cl-som-am57x
- Fixes for torpedo dts to make WLAN behave and to remove a duplicate
i2c rate entry
This series also includes few minor changes that are not stricly
fixes, but would be good to get in during the early -rc cycle:
- Remove legacy mailbox platform data that is no longer needed
- Add the pdata-quirks needed for the new pwm-omap-dmtimer so
people can use it
- Enable ti,mbox-send-noirq that's needed by wkup_m3 driver
- Enable SPLIT and DWARF4 in omap2plus_defconfig as it makes the
initramfs quite a bit smaller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NqvQ
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps with the most intrusive stuff being read-only data
assembly fixes, the other things are mostly board related:
- A series of omap assembly code fixes to fix issues with rodata with
ARM_KERNMEM_PERMS enabled. We had several places writing to rodata,
which is bad. The fix in most cases is to load the value from data
section using a pointer. Let's also enable ARM_KERNMEM_PERMS so
DEBUG_RODATA gets selected by default. And while testing things,
I also added few more loadable driver modules to the defconfig that
I seem to need quite often.
- Fix a long standing omap5 RTC mystery and enable RTC where we need
to ensure the SoC msecure pin is high so we can write to the RTC
registers.
- Fix irq types for am437x
- A series of minor dts fixes for sbc-am57x and cl-som-am57x
- Fixes for torpedo dts to make WLAN behave and to remove a duplicate
i2c rate entry
This series also includes few minor changes that are not stricly
fixes, but would be good to get in during the early -rc cycle:
- Remove legacy mailbox platform data that is no longer needed
- Add the pdata-quirks needed for the new pwm-omap-dmtimer so
people can use it
- Enable ti,mbox-send-noirq that's needed by wkup_m3 driver
- Enable SPLIT and DWARF4 in omap2plus_defconfig as it makes the
initramfs quite a bit smaller
* tag 'omap-for-v4.5/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (23 commits)
ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
ARM: dts: am4372: fix irq type for arm twd and global timer
ARM: dts: Fix wl12xx missing clocks that cause hangs
ARM: OMAP: Add PWM dmtimer platform data quirks
ARM: omap2plus_defconfig: Enable ARM_KERNMEM_PERMS and few loadable modules
ARM: OMAP2+: Fix ppa_zero_params and ppa_por_params for rodata
ARM: OMAP2+: Fix l2_inv_api_params for rodata
ARM: OMAP2+: Fix save_secure_ram_context for rodata
ARM: OMAP2+: Fix l2dis_3630 for rodata
ARM: OMAP2+: Fix wait_dll_lock_timed for rodata
ARM: OMAP2+: Remove legacy mailbox device instantiation
ARM: dts: AM4372: Add ti,mbox-send-noirq to wkup_m3 mailbox
ARM: dts: AM33xx: Add ti,mbox-send-noirq to wkup_m3 mailbox
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- sama5d4: error in DBGU index
- addition of phy properties in several boards
- at91sam9n12ek fix a panel compatible string
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWqdjFAAoJEAf03oE53VmQG30H/R9luD6d9ebmhaOE7ay40HAy
RrG8wtRQ/zgxf37SntoJxyVxxXWsDsb7sOR1LRXiT7FEGWr3Eip7B1uwmasC8pky
ich2Yj5pGVUH+qscm26GDGyHbNwIrFOQyl1t/R6upVpITlXa0bpaEIXx3RejH8PN
Wk4pMZg/4OkUXlcmYNU0Rz8ban8GfJ428bkLxMKeUXUAjvevNlWqTvOqC+QIrzUC
w3iDoXfhc81sqrOzBzW44H28g7rh//d3TAfzMbM1BJti880QkP+CksG5qHvogI5f
olN4+9QmV9tLXOr2K6iUkM8dwzHYW/3PPBR1CHODjSLP0rQ2Assy+DPxyO64Rtk=
=jJrB
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
First fixes for 4.5. Only DT changes:
- sama5d4: error in DBGU index
- addition of phy properties in several boards
- at91sam9n12ek fix a panel compatible string
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ type
ARM: dts: at91: sama5d4 xplained: properly mux phy interrupt
ARM: dts: at91: sama5d4ek: add phy address and IRQ for macb0
ARM: dts: at91: sama5d2 xplained: add phy address and IRQ for macb0
ARM: dts: at91: at91sam9n12ek: fix panel compatible string
ARM: dts: at91: sama5d4: fix instance id of DBGU
Signed-off-by: Olof Johansson <olof@lixom.net>
The interrupt-parent property is not needed as it is inherited from
the parent bus and in the case of the CAAM node actively points to
the wrong interrupt controller (GIC instead of GPC). This leads to
the CAAM IRQs not getting unmasked at the GPC level, leaving them
unable to wake the CPU from wait mode, potentially impacting
performance of the CAAM unit when CPUidle is enabled.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update Eth PHY settings to make it possible to run both phys at 1Gbps.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
