IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Use device_get_match_data() which, unlike of_device_get_match_data(),
is compatible with other firmware interfaces than just OF.
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://lore.kernel.org/r/20230514191959.706269-1-marek.vasut+renesas@mailbox.org
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clock controller generates clocks for the whole chip, including
system clocks and all peripheral clocks. This driver support ma35d1
clock gating, divider, and individual PLL configuration.
There are 6 PLLs in ma35d1 SoC:
- CA-PLL for the two Cortex-A35 CPU clock
- SYS-PLL for system bus, which comes from the companion MCU
and cannot be programmed by clock controller.
- DDR-PLL for DDR
- EPLL for GMAC and GFX, Display, and VDEC IPs.
- VPLL for video output pixel clock
- APLL for SDHC, I2S audio, and other IPs.
CA-PLL has only one operation mode.
DDR-PLL, EPLL, VPLL, and APLL are advanced PLLs which have 3
operation modes: integer mode, fraction mode, and spread specturm mode.
Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Introduce Peripherals clock controller for Amlogic A1 SoC family.
A1 SoC has four clock controllers on the board: PLL, Peripherals, CPU,
and Audio.
This patchset adds support for Amlogic A1 Peripherals clock driver and
allows to generate clocks for all A1 SoC peripheral IPs.
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230523135351.19133-7-ddrokosov@sberdevices.ru
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Introduce PLL clock controller for Amlogic A1 SoC family.
The clock unit is an APB slave module that is designed for generating all
of the internal and system clocks.
The SoC uses an external 24MHz crystal; there are 4 internal PLLs:
SYS_PLL/HIFI_PLL/USB_PLL/(FIXPLL), these PLLs generate 27 clock sources.
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230523135351.19133-5-ddrokosov@sberdevices.ru
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Modern meson PLL IPs are a little bit different from early known PLLs.
The main difference is located in the init/enable/disable sequences; the
rate logic is the same.
In A1 PLL, the PLL enable sequence is different, so add new optional pll
reg bits and use the new power-on sequence to enable the PLL:
1. enable the pll, delay for 10us
2. enable the pll self-adaption current module, delay for 40us
3. enable the lock detect module
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Link: https://lore.kernel.org/r/20230523135351.19133-3-ddrokosov@sberdevices.ru
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Compared with the previous SoCs, self-adaption current module
is newly added for A1, and there is no reset parameter except the
fixed pll. Since we use clk-pll generic driver for A1 pll
implementation, rst bit should be optional to support new behavior.
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Link: https://lore.kernel.org/r/20230523135351.19133-2-ddrokosov@sberdevices.ru
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add support for gpucc driver on SM8550, which provides clocks for the
graphics subsystem.
Co-developed-by: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230524181800.28717-3-quic_jkona@quicinc.com
Certain SoCs use the HW_CLK_CTRL feature on some of the clocks they
host. This allows the clocks to be turned on automatically when a
downstream branch tries to change rate or config.
Make it togglable so that we can utilize this.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230517-topic-waipio-gpucc-v1-2-4f40e282af1d@linaro.org
The mdp_clk_src clock should not be turned off. Instead it should be
'parked' to the XO, as most of other mdp_clk_src clocks. Fix that by
using the clk_rcg2_shared_ops.
Fixes: d8b212014e69 ("clk: qcom: Add support for MSM8974's multimedia clock controller (MMCC)")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230507175335.2321503-1-dmitry.baryshkov@linaro.org
The order of DT_SLEEP_CLK and DT_XO are swapped and it is incorrect.
Due to which the clocks for which the parent should be XO is having parent
as SLEEP_CLK and vice versa. So fix the same by re-ordering the entries.
Fixes: 3d89d52970fd ("clk: qcom: add Global Clock controller (GCC) driver for IPQ5332 SoC")
Reported-by: Devi Priya <quic_devipriy@quicinc.com>
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230417105607.4091-1-quic_kathirav@quicinc.com
480MHz is derived from P_GPLL4_OUT_AUX not from P_GPLL4_OUT_MAIN. Update
the freq_tbl with the correct src.
Fixes: 3d89d52970fd ("clk: qcom: add Global Clock controller (GCC) driver for IPQ5332 SoC")
Reported-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230417044342.9406-1-quic_kathirav@quicinc.com
GPLL0_OUT_DIV (.fw_name = "gcc_disp_gpll0_div_clk_src") was previously
made to reuse the same parent enum entry as GPLL0_OUT_MAIN
(.fw_name = "gcc_disp_gpll0_clk_src") in parent_map_2.
Resolve it by introducing its own entry in the parent enum and
correctly assigning it in disp_cc_parent_map_2[].
Fixes: cc517ea3333f ("clk: qcom: Add display clock controller driver for QCM2290")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230412-topic-qcm_dispcc-v2-2-bce7dd512fe4@linaro.org
BI_TCXO_AO (.fw_name = "bi_tcxo_ao") was previously made to reuse the
same parent enum entry as BI_TCXO (.fw_name = "bi_tcxo") in parent_map_2.
Resolve it by introducing its own entry in the parent enum and
correctly assigning it in disp_cc_parent_map_2[].
Fixes: cc517ea3333f ("clk: qcom: Add display clock controller driver for QCM2290")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230412-topic-qcm_dispcc-v2-1-bce7dd512fe4@linaro.org
Networking resets in IPQ6018 all use bitmask as they require multiple
bits to be set and cleared instead of a single bit.
So, current networking resets have the same register and bit 0 set which
is clearly incorrect.
Fixes: d9db07f088af ("clk: qcom: Add ipq6018 Global Clock Controller support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230526190855.2941291-2-robimarko@gmail.com
Add the compatible and configuration values for A73 Huayra PLL found
on IPQ9574.
Co-developed-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406061314.10916-3-quic_devipriy@quicinc.com
The PXA platform has a number of configurations that end up with
a warning like these when building with W=1:
drivers/hwmon/max1111.c:83:5: error: no previous prototype for 'max1111_read_channel' [-Werror=missing-prototypes]
arch/arm/mach-pxa/reset.c:86:6: error: no previous prototype for 'pxa_restart' [-Werror=missing-prototypes]
arch/arm/mach-pxa/mfp-pxa2xx.c:254:5: error: no previous prototype for 'keypad_set_wake' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa25x.c:70:14: error: no previous prototype for 'pxa25x_get_clk_frequency_khz' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa25x.c:325:12: error: no previous prototype for 'pxa25x_clocks_init' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa27x.c:74:14: error: no previous prototype for 'pxa27x_get_clk_frequency_khz' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa27x.c:102:6: error: no previous prototype for 'pxa27x_is_ppll_disabled' [-Werror=missing-prototypes]
drivers/clk/pxa/clk-pxa27x.c:470:12: error: no previous prototype for 'pxa27x_clocks_init' [-Werror=missing-prototypes]
arch/arm/mach-pxa/pxa27x.c:44:6: error: no previous prototype for 'pxa27x_clear_otgph' [-Werror=missing-prototypes]
arch/arm/mach-pxa/pxa27x.c:58:6: error: no previous prototype for 'pxa27x_configure_ac97reset' [-Werror=missing-prototypes]
arch/arm/mach-pxa/spitz_pm.c:170:15: error: no previous prototype for 'spitzpm_read_devdata' [-Werror=missing-prototypes]
The problem is that there is a declaration for each of these, but
it's only seen by the caller and not the callee. Moving these
into appropriate header files ensures that both use the same
calling conventions and it avoids the warnings.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230516153109.514251-11-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is no point to allow selecting clock controller drivers for
Qualcomm ARMv7 SoCs when building ARM64 kernel, and vice versa. This
makes kernel configuration more difficult as many do not remember the
Qualcomm SoCs model names/numbers. No features should be lost because:
1. There won't be a single image for ARMv7 and ARMv8/9 SoCs.
2. Newer ARMv8/9 SoCs won't be running in arm32 emulation mode.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230514114711.18258-1-krzysztof.kozlowski@linaro.org
Add support to handle the invert logic for branch2 clocks.
Invert branch halt would indicate the clock ON when CLK_OFF
bit is '1' and OFF when CLK_OFF bit is '0'.
Signed-off-by: Imran Shaik <quic_imrashai@quicinc.com>
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230512122347.1219-2-quic_tdas@quicinc.com
On older platforms like msm8226, msm8974 and msm8916 the driver in the
downstream kernel enables scaling first before doing the handover of the
clocks.
While this normally doesn't seem to cause noticeable problems, on
apq8026-asus-sparrow this causes the device to immediately reboot,
perhaps due to older rpm firmware that becomes unhappy.
On newer platforms the order has swapped and enabling scaling is done
after the handover, so let's introduce this behavior only conditionally
for msm8226 and msm8974 for now.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230506-rpmcc-scaling-handover-v1-1-374338a8dfd9@z3ntu.xyz
The same exact F frequency table entry is defined in clk-rcg.h
Drop the redundant define to cleanup code.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230417174408.23722-2-ansuelsmth@gmail.com
The same exact F frequency table entry is defined in clk-rcg.h
Drop the redundant define to cleanup code.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230417174408.23722-1-ansuelsmth@gmail.com
The vast majority of shared RCGs were not marked as such. Fix it.
Fixes: 496d1a13d405 ("clk: qcom: Add Global Clock Controller driver for QCM2290")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230403174807.345185-1-konrad.dybcio@linaro.org
Add support for the video clock controller for video clients to be able
to request for videocc clocks on SM8550 platform.
Co-developed-by: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230524145203.13153-4-quic_jkona@quicinc.com
The lucid ole pll reuses lucid evo ops but it has an additional test
control register which is required to be programmed, add support to
program the same.
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230524145203.13153-2-quic_jkona@quicinc.com
Add support for the video clock controller driver for peripheral clock
clients to be able to request for video cc clocks.
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230524140656.7076-3-quic_tdas@quicinc.com
SDCC clocks must be rounded down to avoid overclocking the controller.
Fixes: d9db07f088af ("clk: qcom: Add ipq6018 Global Clock Controller support")
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1682413909-24927-1-git-send-email-mantas@8devices.com
We should never let go of the active-only XO vote, as otherwise the
RPM may decide that there are no online users and it can be shut down,
resulting in a total, uncontrolled system collapse.
Guarantee this through adding the CLK_IS_CRITICAL flag.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230501-topic-rpmcc_xo_a-v1-3-93f18e47b607@linaro.org
In preparation for supporting keepalive clocks which can never be shut off
(as the platform would fall apart otherwise), make the
DEFINE_CLK_SMD_RPM_BRANCH_A macro accept clock flags for the active-only
clock.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230501-topic-rpmcc_xo_a-v1-2-93f18e47b607@linaro.org
In preparation for supporting keepalive clocks which can never be shut off
(as the platform would fall apart otherwise), make the
__DEFINE_CLK_SMD_RPM_BRANCH_PREFIX macro accept clock flags for the
active-only clock.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230501-topic-rpmcc_xo_a-v1-1-93f18e47b607@linaro.org
For no apparent reason (as there's just one RPM per SoC), all clocks
currently store a copy of a pointer to smd_rpm. Introduce a single,
global one to save up on space in each clk definition.
bloat-o-meter reports:
Total: Before=41887, After=40843, chg -2.49%
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230501130400.107771-1-konrad.dybcio@linaro.org
Camera titan top GDSC is a parent supply to all other camera GDSCs. Titan
top GDSC is required to be enabled before enabling any other camera GDSCs
and it should be disabled only after all other camera GDSCs are disabled.
Ensure this behavior by marking titan top GDSC as parent of all other
camera GDSCs.
Fixes: 15d09e830bbc ("clk: qcom: camcc: Add camera clock controller driver for SC7180")
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230501142932.13049-1-quic_tdas@quicinc.com
After the internal discussions, it looks like this clock is managed by
RPM itself. Linux kernel should not touch it on its own, as this causes
disagreement with RPM. Shutting down this clock causes the OCMEM<->GPU
interface to stop working, resulting in GPU hangchecks/timeouts.
Fixes: d8b212014e69 ("clk: qcom: Add support for MSM8974's multimedia clock controller (MMCC)")
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230508153319.2371645-1-dmitry.baryshkov@linaro.org
SDCC clocks must be rounded down to avoid overclocking the controller.
Fixes: 3d89d52970fd ("clk: qcom: add Global Clock controller (GCC) driver for IPQ5332 SoC")
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230508163145.9678-1-quic_kathirav@quicinc.com
As per the RZ/G2L HW(Rev.1.30 May2023) manual, there are no "write enable"
bits in the CPG_SIPLL5_CLK1 register. So fix the CPG_SIPLL5_CLK register
write by removing the "write enable" bits.
Fixes: 1561380ee72f ("clk: renesas: rzg2l: Add FOUTPOSTDIV clk support")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230518152334.514922-1-biju.das.jz@bp.renesas.com
[geert: Remove CPG_SIPLL5_CLK1_*_WEN bit definitions]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230310144701.1541573-1-robh@kernel.org
As part of converting RISC-V SOC_FOO symbols to ARCH_FOO to match the
use of such symbols on other architectures, convert the Microchip FPGA
clock drivers to use the new symbol.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230309204452.969574-2-conor@kernel.org
TCON0's source clock can be fed from either PLL_MIPI, or PLL_VIDEO0(2X),
however MIPI DSI output only seems to work when PLL_MIPI is selected and
thus the choice must be hardcoded in.
Currently, this driver can't propagate rate change from N-K-M clocks
(such as PLL_MIPI) upwards. This prevents PLL_VIDEO0 from participating
in setting of the TCON0 data clock rate, limiting the precision with
which a target pixel clock can be matched.
For outputs with fixed TCON0 divider, that is DSI and LVDS, the dotclock
can deviate up to 8% off target.
Signed-off-by: Roman Beranek <me@crly.cz>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20230505052110.67514-2-me@crly.cz
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
This loop is freeing "clk" so it needs to use list_for_each_entry_safe().
Otherwise it dereferences a freed variable to get the next item on the
loop.
Fixes: 77d8f3068c63 ("clk: imx: scu: add two cells binding support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/0793fbd1-d2b5-4ec2-9403-3c39343a3e2d@kili.mountain
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20230421115517.1940990-1-alexander.stein@ew.tq-group.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
On the i.MX6SX, it is common to use the LDB and LCDIF with the same
parent clock, such as the IMX6SX_CLK_PLL5_VIDEO_DIV, for example.
Due to the CLK_SET_RATE_PARENT flag, the LDB clock would try to set the
clock parent rate, which can mess with the required clock rate calculated
from the eLCDIF driver.
To prevent this problem, remove the CLK_SET_RATE_PARENT flag from the
LDB clocks, so that a correct clock relationship can be achieved.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230416150004.16834-1-festevam@gmail.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
