IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The I40E_FLAG_NEED_LINK_UPDATE was never used. Remove the flag
definitions.
Change-ID: If59d0c6b4af85ca27281f3183c54b055adb439a4
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can simply check both Tx and Rx queues in a single loop, rather than
repeating the loop twice.
Change-ID: Ic06f26b0e3c2620e0e33c1a2999edda488e647ad
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Look up the MAC address from the eth_get_platform_mac_address() function
first before checking what the firmware provides. We already handle the
case of re-writing the MAC-VLAN filter, so there is no need to add extra
code for this. However, update the comment where we do this to indicate
that it does impact the Open Firmware MAC address case.
Change-ID: I73e59fbe0b0e7e6f3ee9f5170d0bd3a4d5faf4db
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch greatly reduces the unneeded complexity in the
i40e_detect_recover_hung_queue code path. The previous implementation
set a 'hung bit' which would then get cleared while polling. If the
detection routine was called a second time with the bit already set, we
would issue a software interrupt. This patch makes it such that if
interrupts are disabled and we have pending TX descriptors, we trigger a
software interrupt since in, the worst case, queues are already clean
and we have an extra interrupt.
Additionally this patch removes the workaround for lost interrupts as
calling napi_reschedule in this context can cause software interrupts to
fire on the wrong CPU.
Change-ID: Iae108582a3ceb6229ed1d22e4ed6e69cf97aad8d
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously rtnl lock was held during whole reset procedure that
was stopping other PFs running their reset procedures. In the result
reset was not handled properly and host reset was the only way
to recover.
Change-ID: I23c0771c0303caaa7bd64badbf0c667e25142954
Signed-off-by: Maciej Sosin <maciej.sosin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The client interface is only intended for use on devices that support
iWarp. Only register with the client if this is the case.
This fixes a panic when loading i40iw on X710 devices.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Reported-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the driver is removed or shut down, close any attached clients
(i.e. i40iw). This prevents a panic seen sometimes on forced driver
removal or system shutdown when iWarp is running.
Change-ID: I4f6161e5a73ffbb2fd5883567b007310302bfcb5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a capability negotiation between VF and PF using ENCAP/
ENCAP_CSUM offload flags in order for the VF to support outer checksum
and TSO offloads for encapsulated packets. These capabilities were assumed
by default and enabled in current hardware. Going forward, these features
needs to be negotiated with PF before advertising to the stack.
Additionally, strip out the mac.type checks for X722 since outer checksums
are enabled based on the ENCAP_CSUM offload negotiation flag and maintain
consistency between drivers in how the features are configured.
Change-ID: Ie380a6f57eca557a2bb575b66b12fae36d308920
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Signed-off-by: Alan Brady <alan.brady@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a delay to Rx queue disables to accommodate HW needs.
v2: Added missing check for disable only, additional details on the
need for the ugly delay and fixed spacing on comment.
Change-ID: I2864ca667ce5dcc2cc44f8718113b719742a46a1
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the way we handle the maximum frame size for the Rx
path. Previously we were rounding up to 2K for a 1500 MTU and then brining
the max frame size down to MTU plus a fixed amount. With this patch
applied what we now do is limit the maximum frame to 1.5K minus the value
for NET_IP_ALIGN for standard MTU, and for any MTU greater than 1500 we
allow up to the maximum frame size. This makes the behavior more
consistent with the other drivers such as igb which had similar logic. In
addition it reduces the test matrix for MTU since we only have two max
frame sizes that are handled for Rx now.
Change-ID: I23a9d3c857e7df04b0ef28c64df63e659c013f3f
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The goto found here for when in MFP mode is pointless. It jumps to the
end of a series of if blocks. However, right after this statement is
a closing '}' for this if block, which will result in the program flow
going to the exact same location as the goto statement indicates. Thus,
regardless of whether we are in MFP mode, the program flow will resume
from the same location.
This arose due to various refactoring which did not notice that this
goto became essentially a no-op.
To properly understand this diff you will need to view a larger context
than is given by default.
Change-ID: I088f73c3831aa5c4e2281380c7a3ce605594300c
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a case where we miss an arq element if a new one is added before we
enable interrupts and exit the arq subtask loop. This occurs frequently
with RDMA running on Windows VF and causes long delays that prevent SMB
from establishing connections.
Change-ID: I3e1c8b2b960c12857d9b8275bea2c1563674392e
Signed-off-by: Christopher N Bednarz <christopher.n.bednarz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since FCoE isn't supported by the i40e products there isn't much point in
carrying around code that will always evaluate to false. This patch goes
through and strips out the code in several spots so that we don't go around
carrying variables and/or code that is always going to evaluate to false or
0.
Change-ID: I39d1d779c66c638b75525839db2b6208fdc809d7
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Looking over the code for FCoE it looks like the Rx path has been broken at
least since the last major Rx refactor almost a year ago. It seems like
FCoE isn't supported for any of the Fortville/Fortpark hardware so there
isn't much point in carrying the code around, especially if it is broken
and untested.
Change-ID: I892de8fa551cb129ce2361e738ff82ce55fa229e
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removed no longer needed delays. At preproduction stage those delays were
needed but now these delays are not needed.
Signed-off-by: Bimmy Pujari <bimmy.pujari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists a bug in the driver where the calculation of the
RSS size was not taking into account the number of traffic classes
enabled. This patch factors in the traffic classes both in
the initial configuration of the table as well as reconfiguration.
Change-ID: I34dcd345ce52faf1d6b9614bea28d450cfd5f621
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When testing the epoll w/ busy poll code I found that I could get into a
state where the i40e driver had q_vectors w/ active NAPI that had no rings.
This was resulting in a divide by zero error. To correct it I am updating
the driver code so that we only support NAPI on q_vectors that have 1 or
more rings allocated to them.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a complex if->continue->else->break construction in
i40e_next_filter. We can simply use hlist_for_each_entry_continue
instead. This drops a lot of confusing code. The resulting code is much
easier to understand the intention, and follows the more normal pattern
for using hlist loops. We could have also used a break with a "return
next" at the end of the function, instead of return NULL, but the
current implementation is explicitly clear that when you reach the end
of the loop you get a NULL value. The alternative construction is less
clear since the reader would have to know that next is NULL at the end
of the loop.
Change-Id: Ife74ca451dd79d7f0d93c672bd42092d324d4a03
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable FDir filters for SCTPv4 packets using the ethtool ntuple
interface to enable filters. The ethtool API does not allow masking on
the verification tag.
Change-Id: I093e88a8143994c7e6f4b7b17a0bd5cf861d18e4
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for flexible payloads passed via ethtool user-def field.
This support is somewhat limited due to hardware design. The input set
can only be programmed once per filter type, and the flexible offset is
part of this filter input set. This means that the user cannot program
both a regular and a flexible filter at the same time for a given flow
type. Additionally, the user may not program two flexible filters of the
same flow type with different offsets, although they are allowed to
configure different values at that offset location.
We support a single flexible word (2byte) value per protocol type, and
we handle the FLX_PIT register using a list of flexible entries so that
each flow type may be configured separately.
Due to hardware implementation, the flexible data is offset from the
start of the packet payload, and thus may not be in part of the header
data. For this reason, the offset provided by the user defined data is
interpreted as a byte offset from the start of the matching payload.
Previous implementations have tried to represent the offset as from the
start of the frame, but this is not feasible because header sizes may
change due to options.
Change-Id: 36ed27995e97de63f9aea5ade5778ff038d6f811
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ensure that the default input set is correctly reprogrammed when
cleaning up after disabling flow director support. This ensures that the
programmed value will be in a clean state.
Although we do not yet have support for SCTPv4 filters, a future patch
will add support for this protocol, so we will correctly restore the
SCTPv4 input set here as well. Note that strictly speaking the default
hardware value for SCTP includes matching the verification tag. However,
the ethtool API does not have support for specifying this value, so
there is no reason to keep the verification field enabled.
This patch is the next step on the way to enabling partial tuple filters
which will be implemented in a following patch.
Change-Id: Ic22e1c267ae37518bb036aca4a5694681449f283
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation for adding code to properly check the mask values, we
will need to know the number of active filters for each type. Add
counters for each filter type. Rename the already existing fd_tcp_rule
to fd_tcp4_filter_cnt to match the style of other names. To avoid style
warnings, avoid assigning multiple parameters at once, and fix up one
other case where we did so previously.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When flushing and replaying FDIR filters, it is possible we would
disable ATR, and then re-enable it even though we should have kept
it disabled due to existing TCP/IPv4 filters. Fix this by checking
whether we have TCP4/IPv4 filters before re-enabling.
Alternatively, we could instead restore ATR and then replay filters,
however, this would cause us to rapidly enable and then disable ATR in
some cases.
Change-ID: I076e4cc1e4409bce7f98f3c213295433a4ff43d8
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Avinash Dayanand <avinash.dayanand@intel.com>
Reviewed-by: Alan Brady <alan.brady@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we're about to reprogram the filters, we need to ensure that the
fd_tcp_rule count is correctly reset to 0. Otherwise, we will keep
a stale count that does not accurately reflect the number of programmed
TCPv4 filters.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_fdir_filter_restore re-adds all existing filters, which already
checks when adding a TCPv4 filter to disable ATR. We don't need to make
the check twice, so remove this redundant code.
Change-ID: Ia0b0690e23523915199d601494557def135c9d7f
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The firmware expects the port numbers for offloaded UDP tunnels in
Little Endian format. We accidentally sent the value in Big Endian
format which obviously will cause the wrong port number to be put into
the UDP tunnels list. This results in VxLAN and Geneve tunnel Rx
offloads being essentially disabled, unless the port number happens to
be identical after byte swapping. Note that i40e_aq_add_udp_tunnel()
will byteswap the parameter from host order into Little Endian so we
don't need worry about passing strictly a __le16 value to the command.
This patch essentially reverts b3f5c7bc88ba ("i40e: Fix for extra byte
swap in tunnel setup", 2016-08-24), but in a way that makes the result
much more clear to the reader.
Fixes: b3f5c7bc88ba ("i40e: Fix for extra byte swap in tunnel setup", 2016-08-24)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Williams, Mitch A <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The configurable priority to traffic class mapping and the user specified
queue ranges are used to configure the traffic class, overriding the
hardware defaults when the 'hw' option is set to 0. However, when the 'hw'
option is non-zero, the hardware QOS defaults are used.
This patch makes it so that we can pass the data the user provided to
ndo_setup_tc. This allows us to pull in the queue configuration if the
user requested it as well as any additional hardware offload type
requested by using a value other than 1 for the hw value.
Finally it also provides a means for the device driver to return the level
supported for the offload type via the qopt->hw value. Previously we were
just always assuming the value to be 1, in the future values beyond just 1
may be supported.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous commit introduced a field that tracks the features
that are disabled due to HW resource limitations as opposed
to the featured disabled by the user. This patch changes the
name of the field to make it more readable since it might get
confusing when looking at code containing both the flags
field and the auto_disable_features field together.
Change-ID: Idcc9888659698f6fe3ccff17c8c3f09b5026f708
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch clarifies the reason for removal of automatically
firmware-generated filter and explicit addition of filter which
accepts frames with any VLAN id.
Change-ID: Iabf180b6d61c4d8a36d3bcf8457c377a6f2aca0e
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the issue that RSS offloading only works on PF0 by
using the direct register writing of the hash keys for the VFs instead
of using the admin queue command to do so.
Change-ID: Ia02cda7dbaa23def342e8786097a2c03db6f580b
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a solution to avoid adding too many queues to num_lan_msix.
A recent refactor of queue pairs accidentally added all remaining
vectors to the num_lan_msix which can have adverse performance issues,
due to enabling more queues than the number of CPU cores.
This patch removes the old calculation, and replaces it with a simple
algorithm.
1) add queue pairs up to num_online_cpus(), but capped at half of total
vectors
2) then add alternative features such as flow directory and similar
3) finally, add the remaining vectors back to queue pairs, but capped
such that the total number of queue pairs does not exceed
num_online_cpus().
Change-ID: I668abf67d5011a1248866daba8885f4ff00cb8d9
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
(KISS is Keep It Simple, Stupid. Or is it?)
The client interface vastly overengineered for what it needs to do.
It was originally designed to support multiple clients on multiple
netdevs, possibly even with multiple drivers. None of this happened,
and now we know that there will only ever be one client for i40e
(i40iw) and one for i40evf (i40iwvf). So, time for some KISS. Since
i40e and i40evf are a Dynasty, we'll simplify this one to match the
VF interface.
First, be a Destroyer and remove all of the lists and locks required
to support multiple clients. Keep one static around to keep track of
one client, and track the client instances for each netdev in the
driver's pf (or adapter) struct. Now it's Almost Human.
Since we already know the client type is iWarp, get rid of any checks
for this. Same for VSI type - it's always going to be the same type,
so it's just a Parasite.
While we're at it, fix up some comments. This makes the function
headers actually match the functions.
These changes reduce code complexity, simplify maintenance,
squash some lurking timing bugs, and allow us to Rock and Roll All
Nite.
Change-ID: I1ea79948ad73b8685272451440a34507f9a9012e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The following message is logged from time to time when using i40e:
NOHZ: local_softirq_pending 08
i40e may schedule napi from a workqueue. Afterwards, softirqs are not run
in a deterministic time frame. The problem is the same as what was
described in commit ec13ee80145c ("virtio_net: invoke softirqs after
__napi_schedule") and this patch applies the same fix to i40e.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists an intermittent bug which causes the 'Link Detected'
field reported by the 'ethtool <iface>' command to be 'Yes' when
in fact, there is no link. This patch fixes the problem by
enabling temporary link polling when i40e_get_link_status returns
an error. This causes the driver to remember that an admin queue
command failed and polls, until the function returns with a success.
Change-Id: I64c69b008db4017b8729f3fc27b8f65c8fe2eaa0
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This ensures that the pvid which is stored in __le16 format is converted
to the CPU format. This will fix comparison issues on Big Endian
platforms.
Change-ID: I92c80d1315dc2a0f9f095d5a0c48d461beb052ed
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This call is made just prior to running i40e_link_event. In
i40e_link_event, we set hw->phy.get_link_info to true just prior to
calling i40e_get_link_status, which conveniently runs
i40e_update_link_info for us. Thus, we are running i40e_update_link_info
twice, which seems like something we don't need to do...
Change-ID: I36467a570f44b7546d218c99e134ff97c2709315
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a call to the mac_address_write admin q function during
power down to update the PRTPM_SAH/SAL registers with the MC_MAG_EN bit
thus enabling multicast magic packet wakeup.
A FW workaround is needed to write the multicast magic wake up enable
bit in the PRTPM_SAH register. The FW expects the mac address write
admin q cmd to be called first with one of the WRITE_TYPE_LAA flags
and then with the multicast relevant flags.
*Note: This solution only works for X722 devices currently. A PFR will
clear the previously mentioned bit by default, but X722 has support for a
WOL_PRESERVE_ON_PFR flag which prevents the bit from being cleared. Once
other devices support this flag, this solution should work as well.
Change-ID: I51bd5b8535bd9051c2676e27c999c1657f786827
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists a bug in which the driver is unable to exit overflow
promiscuous mode after having added "too many" mac filters. It is
expected that after triggering overflow promiscuous, removing the
failed/extra filters should then disable overflow promiscuous mode.
The bug exists because we were intentionally skipping the sync_vsi_filter
path in cases where we were removing failed filters since they shouldn't
have been added to the firmware in the first place, however we still
need to go through the sync_vsi_filter code path to determine whether or
not it is ok to exit overflow promiscuous mode. This patch fixes the
bug by making sure we go through the sync_vsi_filter path in cases of
failed filters.
Change-ID: I634d249ca3e5fa50729553137c295e73e7722143
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor how we add new filters to firmware to avoid a race condition
that can occur due to removing filters from the hash temporarily.
To understand the race condition, suppose that you have a number of MAC
filters, but have not yet added any VLANs. Now, add two VLANs in rapid
succession. A possible resulting flow would look something like the
following:
(1) lock hash for add VLAN
(2) add the new MAC/VLAN combos for each current MAC filter
(3) unlock hash
(4) lock hash for filter sync
(5) notice that we have a VLAN, so prepare to update all MAC filters
with VLAN=-1 to be VLAN=0.
(6) move NEW and REMOVE filters to temporary list
(7) unlock hash
(8) lock hash for add VLAN
(9) add new MAC/VLAN combos. Notice that no MAC filters are currently in
the hash list, so we don't add any VLANs <--- BUG!
(10) unlock hash
(11) sync the temporary lists to firmware
(12) lock hash for post-sync
(13) move the temporary elements back to the main list
....
Because we take filters out of the main hash into temporary lists, we
introduce a narrow window where it is possible that other callers to the
list will not see some of the filters which were previously added but
have not yet been finalized. This results in sometimes dropping VLAN
additions, and could also result in failing to add a MAC address on the
newly added VLAN.
One obvious way to avoid this race condition would be to lock the entire
firmware process. Unfortunately this does not work because adminq
firmware commands take a mutex which results in a sleep while atomic
BUG(). So, we can't use the simplest approach.
An alternative approach is to simply not remove the filters from the
hash list while adding. Instead, add an i40e_new_mac_filter structure
which we will use to track added filters. This avoids the need to remove
the filter from the hash list. We'll store a pointer to the original
i40e_mac_filter, along with our own copy of the state.
We won't update the state directly, so as to avoid race with other code
that may modify the state while under the lock. We are safe to read
f->macaddr and f->vlan since these only change in two locations. The
first is on filter creation, which must have already occurred. The
second is inside i40e_correct_vlan_filters which was previously run
after creation of this object and can't be run again until after. Thus,
we should be safe to read the MAC address and VLAN while outside the
lock.
We also aren't going to run into a use-after-free issue because the only
place where we free filters is when they are marked FAILED or when we
remove them inside the sync subtask. Since the subtask has its own
critical flag to prevent duplicate runs, we know this won't happen. We
also know that the only location to transition a filter from NEW to
FAILED is inside the subtask also, so we aren't worried about that
either.
Use the wrapper i40e_new_mac_filter for additions, and once we've
finalized the addition to firmware, we will update the filter state
inside a lock, and then free the wrapper structure.
In order to avoid a possible race condition with filter deletion, we
won't update the original filter state unless it is still
I40E_FILTER_NEW when we finish the firmware sync.
This approach is more complex, but avoids race conditions related to
filters being temporarily removed from the list. We do not need the same
behavior for deletion because we always unconditionally removed the
filters from the list regardless of the firmware status.
Change-Id: I14b74bc2301f8e69433fbe77ebca532db20c5317
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug where we modified the mac_filter_hash while outside a lock,
when handling addition of broadcast filters.
Normally, we add filters to firmware by batching the additions into
lists and issuing 1 update for every few filters. Broadcast filters are
handled differently, by instead setting the broadcast promiscuous mode
flags. In order to make sure the 1<->1 mapping of filters in our
addition array lined up with filters in the hlist tmp_add_list, we had
to remove the filter and move it back to the main hash. However, we
didn't do this under lock, which could cause consistency problems for
the list.
Fix this by updating i40e_update_filter_state logic so that it knows to
avoid broadcast filters. This ensures that we don't have to remove the
filter separately, and can put it back using the normal flow.
Change-ID: Id288fade80b3e3a9a54b68cc249188cb95147518
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store the FEC status bits from the link up event into the
hw_link_info structure.
Change-ID: I9a7b256f6dfb0dce89c2f503075d0d383526832e
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently i40e_bus_info has PCI device and function info only and log
messages print device number as bus number. Added field to provide bus
number info and modified log statements to print bus, device and
function information.
Change-ID: I811617cee2714cc0d6bade8d369f57040990756f
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch refactors the macro INTRL_USEC_TO_REG into a static inline
function and fixes a couple subtle bugs caused by the macro.
This patch fixes a bug which was caused by passing a bad register value
to the firmware. If enabling interrupt rate limiting, a non-zero value
for the rate limit must be used. Otherwise the firmware sets the
interrupt rate limit to the maximum value. Due to the limited
resolution of the register, attempting to set a value of 1, 2, or 3
would be rounded down to 0 and limiting was left enabled, causing
unexpected behavior.
This patch also fixes a possible bug in which using the macro itself can
introduce unintended side-affects because the macro argument is used
more than once in the macro definition (e.g. a variable post-increment
argument would perform a double increment on the variable).
Without this patch, attempting to set interrupt rate limits of 1, 2, or
3 results in unexpected behavior and future use of this macro could
cause subtle bugs.
Change-Id: I83ac842de0ca9c86761923d6e3a4d7b1b95f2b3f
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I40E_MAC_X710 was supposed to be for 10G and I40E_MAC_XL710
was supposed to be for 40G. But function i40e_is_mac_710
sets I40E_MAC_XL710 for all device IDS, I40E_MAC_X710 is not
used at all. As there is nothing to compare there is no need
for this function. Thus deprecating this extra macro and
removing this function entirely and replacing it with a direct
check.
Change-ID: I7d1769954dccd574a290ac04adb836ebd156730e
Signed-off-by: Bimmy Pujari <bimmy.pujari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of using i40e_add_filter or i40e_del_filter directly, when
adding a MAC address, we should normally be using i40e_add_mac_filter or
i40e_del_mac_filter. These functions correctly handle the various cases
of VLAN mode or PVID settings. This ensures consistency and avoids the
issues that can occur with the recent addition of a WARN_ON() in
i40e_sync_vsi_filters.
Change-ID: I7fe62db063391fdd1180b2d6a6a3c5ab4307eeee
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use __i40e_del_filter instead of using i40e_del_filter() which will
avoid doing an additional search to delete a filter we already have the
pointer for.
Change-ID: Iea5a7e3cafbf8c682ed9d3b6c69cf5ff53f44daf
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
