IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
If an eDP panel is not powered on then any attempts to talk to it over
the DP AUX channel will timeout. Unfortunately these attempts may be
quite slow. Userspace can initiate these attempts either via a
/dev/drm_dp_auxN device or via the created i2c device.
Making the DP AUX drivers timeout faster is a difficult proposition.
In theory we could just poll the panel's HPD line in the AUX transfer
function and immediately return an error there. However, this is
easier said than done. For one thing, there's no hard requirement to
hook the HPD line up for eDP panels and it's OK to just delay a fixed
amount. For another thing, the HPD line may not be fast to probe. On
parade-ps8640 we need to wait for the bridge chip's firmware to boot
before we can get the HPD line and this is a slow process.
The fact that the transfers are taking so long to timeout is causing
real problems. The open source fwupd daemon sometimes scans DP busses
looking for devices whose firmware need updating. If it happens to
scan while a panel is turned off this scan can take a long time. The
fwupd daemon could try to be smarter and only scan when eDP panels are
turned on, but we can also improve the behavior in the kernel.
Let's let eDP panels drivers specify that a panel is turned off and
then modify the common AUX transfer code not to attempt a transfer in
this case.
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested-by: Eizan Miyamoto <eizan@chromium.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202141109.1.I24277520ac754ea538c9b14578edc94e1df11b48@changeid
Add support for Display Port tunneling. For now this includes the
support for Bandwidth Allocation Mode (BWA), leaving adding Panel Replay
support for later.
BWA allows using displays that share the same (Thunderbolt) link with
their maximum resolution. Atm, this may not be possible due to the
coarse granularity of partitioning the link BW among the displays on the
link: the BW allocation policy is in a SW/FW/HW component on the link
(on Thunderbolt it's the SW or FW Connection Manager), independent of
the driver. This policy will set the DPRX maximum rate and lane count
DPCD registers the GFX driver will see (0x00000, 0x00001, 0x02200,
0x02201) based on the available link BW.
The granularity of the current BW allocation policy is coarse, based on
the required link rate in the 1.62Gbs..8.1Gbps range and it may prevent
using higher resolutions all together: the display connected first will
get a share of the link BW which corresponds to its full DPRX capability
(regardless of the actual mode it uses). A subsequent display connected
will only get the remaining BW, which could be well below its full
capability.
BWA solves the above coarse granularity (reducing it to a 250Mbs..1Gps
range) and first-come/first-served issues by letting the driver request
the BW for each display on a link which reflects the actual modes the
displays use.
This patch adds the DRM core helper functions, while a follow-up change
in the patchset takes them into use in the i915 driver.
v2:
- Fix prepare_to_wait vs. wake-up cond check order in
allocate_tunnel_bw(). (Ville)
- Move tunnel==NULL checks from callers in drivers to here. (Ville)
- Avoid var inits in declaration blocks that can fail or have
side-effects. (Ville)
- Use u8 for driver and group IDs. (Ville)
- Simplify API removing drm_dp_tunnel_get/put_untracked(). (Ville)
- Reuse str_yes_no() instead of a local yes_no_chr(). (Ville)
- s/drm_dp_tunnel_atomic_clear_state()/free_tunnel_state() and unexport
the function. (Ville)
- s/clear_tunnel_group_state()/free_group_state() and move kfree() to
this function. (Ville)
- Add separate group_free_bw() helper and describe what the tunnel
estimated BW includes. (Ville)
- Improve help text for CONFIG_DRM_DISPLAY_DP_TUNNEL. (Ville)
- Add code comment explaining the purpose of DPCD reg read helpers.
(Ville)
- Add code comment describing the tunnel group name prefix format.
(Ville)
- Report the allocated BW as undetermined until the first allocation
request.
- Skip allocation requests matching the previous request.
- Clear any stale BW request status flags before a new request.
- Add missing error return check of drm_dp_tunnel_atomic_get_group_state()
in drm_dp_tunnel_atomic_set_stream_bw().
- Add drm_dp_tunnel_get_allocated_bw().
- s/drm_dp_tunnel_atomic_get_tunnel_bw/drm_dp_tunnel_atomic_get_required_bw
- Fix return value description in function doc of drm_dp_tunnel_detect().
- Add function documentation to all exported functions.
v3:
- Improve grouping of fields in drm_dp_tunnel_group struct. (Uma)
- Fix validating the BW granularity DPCD reg value. (Uma)
- Document return value of check_and_clear_status_change(). (Uma)
- Fix resetting drm_dp_tunnel_ref::tunnel in drm_dp_tunnel_ref_put().
(Ville)
- Allow for ALLOCATED_BW to change after a BWA enable/disable sequence.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240226185246.1276018-2-imre.deak@intel.com
Copy intel_dp_max_data_rate() to DRM core. It will be needed by a
follow-up DP tunnel patch, checking the maximum rate the DPRX (sink)
supports. Accordingly use the drm_dp_max_dprx_data_rate() name for
clarity. This patchset will also switch calling the new DRM function
in i915 instead of intel_dp_max_data_rate().
While at it simplify the function documentation/comments, removing
parts described already by drm_dp_bw_channel_coding_efficiency().
v2: (Ville)
- Remove max_link_rate_kbps.
- Simplify the function documentation.
v3:
- Rebased on latest drm-tip.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240226185246.1276018-1-imre.deak@intel.com
YUV420 format is supported only in the VSC SDP packet and not through
MSA. Hence add an API which indicates the sink support which can be used
by the rest of the DP programming.
changes in v5:
- rebased on top of drm-tip
changes in v4:
- bail out early if dpcd rev check fails
changes in v3:
- fix the commit title prefix to drm/dp
- get rid of redundant !!
- break out this change from series [1] to get acks from drm core
maintainers
Changes in v2:
- Move VSC SDP support check API from dp_panel.c to
drm_dp_helper.c
[1]: https://patchwork.freedesktop.org/series/129180/
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Paloma Arellano <quic_parellan@quicinc.com>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240215191556.3227259-1-quic_abhinavk@quicinc.com
Currently the size parameter of drm_dp_vsc_sdp_pack() is always
the size of struct dp_sdp. Hence lets drop this parameter and
use sizeof() directly.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220195348.1270854-2-quic_abhinavk@quicinc.com
intel_dp_vsc_sdp_pack() can be re-used by other DRM drivers as well.
Lets move this to drm_dp_helper to achieve this.
changes in v2:
- rebased on top of drm-tip
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220195348.1270854-1-quic_abhinavk@quicinc.com
Backmerging to update drm-misc-next to the state of v6.8-rc3. Also
fixes a build problem with xe.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Stephen Rothwell reported htmldocs warnings when merging drm-intel
tree:
Documentation/gpu/drm-kms-helpers:296: drivers/gpu/drm/display/drm_dp_mst_topology.c:5484: ERROR: Unexpected indentation.
Documentation/gpu/drm-kms-helpers:296: drivers/gpu/drm/display/drm_dp_mst_topology.c:5488: WARNING: Block quote ends without a blank line; unexpected unindent.
Separate @failing_port return value list by surrounding it with a
blank line to fix above warnings.
Fixes: 1cd0a5ea427931 ("drm/dp_mst: Factor out a helper to check the atomic state of a topology manager")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/linux-next/20231114141715.6f435118@canb.auug.org.au/
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231114081033.27343-1-bagasdotme@gmail.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
(controllers set the flag, but there is no client to use it). Also,
CLASS_SPD support gets simplified to prepare removal in the future.
Class based instantiation is not recommended these days anyhow.
Furthermore, I2C core now creates a debugfs directory per I2C adapter.
Current bus driver users were converted to use it. Then, there are also
quite some driver updates. Standing out are patches for the wmt-driver
which is refactored to support more variants. This is the rebased pull
request where a large series for the designware driver was dropped.
-----BEGIN PGP SIGNATURE-----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=8D3Q
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.8-rc1-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"This removes the currently unused CLASS_DDC support (controllers set
the flag, but there is no client to use it).
Also, CLASS_SPD support gets simplified to prepare removal in the
future. Class based instantiation is not recommended these days
anyhow.
Furthermore, I2C core now creates a debugfs directory per I2C adapter.
Current bus driver users were converted to use it.
Finally, quite some driver updates. Standing out are patches for the
wmt-driver which is refactored to support more variants.
This is the rebased pull request where a large series for the
designware driver was dropped"
* tag 'i2c-for-6.8-rc1-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
MAINTAINERS: use proper email for my I2C work
i2c: stm32f7: add support for stm32mp25 soc
i2c: stm32f7: perform I2C_ISR read once at beginning of event isr
dt-bindings: i2c: document st,stm32mp25-i2c compatible
i2c: stm32f7: simplify status messages in case of errors
i2c: stm32f7: perform most of irq job in threaded handler
i2c: stm32f7: use dev_err_probe upon calls of devm_request_irq
i2c: i801: Add lis3lv02d for Dell XPS 15 7590
i2c: i801: Add lis3lv02d for Dell Precision 3540
i2c: wmt: Reduce redundant: REG_CR setting
i2c: wmt: Reduce redundant: function parameter
i2c: wmt: Reduce redundant: clock mode setting
i2c: wmt: Reduce redundant: wait event complete
i2c: wmt: Reduce redundant: bus busy check
i2c: mux: reg: Remove class-based device auto-detection support
i2c: make i2c_bus_type const
dt-bindings: at24: add ROHM BR24G04
eeprom: at24: use of_match_ptr()
i2c: cpm: Remove linux,i2c-index conversion from be32
i2c: imx: Make SDA actually optional for bus recovering
...
After removal of the legacy EEPROM driver and I2C_CLASS_DDC support in
olpc_dcon there's no i2c client driver left supporting I2C_CLASS_DDC.
Class-based device auto-detection is a legacy mechanism and shouldn't
be used in new code. So we can remove this class completely now.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The current way of calculating the pbn_div value, the link BW per each
MTP slot, worked only for DP 1.4 link rates. Fix things up for UHBR
rates calculating with the correct channel coding efficiency based on
the link rate.
v2:
- Return the fractional pbn_div value from drm_dp_get_vc_payload_bw().
v3:
- Fix rounding up quotient while calculating req_slots. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231117150929.1767227-1-imre.deak@intel.com
On UHBR links the PBN divider is a fractional number, accordingly store
it in fixed point format. For now drm_dp_get_vc_payload_bw() always
returns a whole number and all callers will use only the integer part of
it which should preserve the current behavior. The next patch will fix
drm_dp_get_vc_payload_bw() for UHBR rates returning a fractional number
for those (also accounting for the channel coding efficiency correctly).
Cc: Lyude Paul <lyude@redhat.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Wayne Lin <wayne.lin@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[Rebased changes in dm_helpers_construct_old_payload() on drm-intel-next]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231116131841.1588781-2-imre.deak@intel.com
Add helpers drivers can use to calculate the BW allocation overhead -
due to SSC, FEC, DSC and data alignment on symbol cycles - and the
channel coding efficiency - due to the 8b/10b, 128b/132b encoding. On
128b/132b links the FEC overhead is part of the coding efficiency, so
not accounted for in the BW allocation overhead.
The drivers can use these functions to calculate a ratio, controlling
the stream symbol insertion rate of the source device in each SST TU
or MST MTP frame. Drivers can calculate this
m/n = (pixel_data_rate * drm_dp_bw_overhead()) /
(link_data_rate * drm_dp_bw_channel_coding_efficiency())
ratio for a given link and pixel stream and with that the
slots_per_mtp = CEIL(64 * m / n)
allocated slots per MTP for the stream in a link frame and with
that the
pbn = slots_per_mtp * drm_mst_get_pbn_divider()
allocated PBNs for the stream on the MST link path.
Take drm_dp_bw_overhead() into use in drm_dp_calc_pbn_mode(), for
drivers calculating the PBN value directly.
v2:
- Add dockbook description to drm_dp_bw_channel_coding_efficiency().
(LKP).
- Clarify the way m/n ratio is calculated in the commit log.
v3:
- Fix compile breakage for !CONFIG_BACKLIGHT_CLASS_DEVICE. (LKP)
- Account for FEC_PM overhead (+ 0.0015625 %), add comment
with the formula to calculate the total FEC overhead. (Ville)
v4:
- Rename DRM_DP_OVERHEAD_SSC to DRM_DP_OVERHEAD_SSC_REF_CLK. (Ville)
v5:
- Clarify in the commit log what MTP means.
- Simplify the commit log's formula to calculate PBN.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: kernel test robot <lkp@intel.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> (v2)
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231107001505.3370108-1-imre.deak@intel.com
Add a quirk for Synaptics MST hubs, which require a workaround - at leat
on i915 - for some modes, on which the hub applies HBLANK expansion.
These modes will only work by enabling DSC decompression for them, a
follow-up patch will do this in i915.
v2:
- Fix the quirk name in its DocBook description.
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231030155843.2251023-9-imre.deak@intel.com
The Synaptics MST branch devices support DSC decompression on all their
output ports, provided that they are last branch devices (with their
output ports connected to the sinks). The Thinkpad 40B0 TBT dock for
instance has two such branch devices, a secondary one connected to one
of the output ports of the primary; hence the decompression needs to be
enabled in both branch devices to enable decompression for all the
sinks.
Based on the above add support for enabling decompression in last
Synaptics branch devices.
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231030155843.2251023-7-imre.deak@intel.com
drm_dp_mst_atomic_check_mgr() should check for BW limitation starting
from sink ports continuing towards the root port, so that drivers can
use the @failing_port returned to resolve a BW overallocation in an
ideal way. For instance from streams A,B,C in a topology A,B going
through @failing_port and C not going through it, a BW overallocation of
A,B due to a limit of the port must be resolved first before considering
the limits of other ports closer to the root port. This way can avoid
reducing the BW of stream C unnecessarily due to a BW limit closer to the
root port.
Based on the above swap the order of the BW check for the root port and
the check for all the ports downstream of it (the latter going through
the topology already in the sink->root port direction).
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231030155843.2251023-6-imre.deak@intel.com
Factor out a helper to check the atomic state for one MST topology
manager, returning the MST port where the BW limit check has failed.
This will be used in a follow-up patch by the i915 driver to improve the
BW sharing between MST streams.
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231030155843.2251023-5-imre.deak@intel.com
The current code does '(bpp << 4) / 16' in the MST PBN
calculation, but that is just the same as 'bpp' so the
DSC codepath achieves absolutely nothing. Fix it up so that
the fractional part of the bpp value is actually used instead
of truncated away. 64*1006 has enough zero lsbs that we can
just shift that down in the dividend and thus still manage
to stick to a 32bit divisor.
And while touching this, let's just make the whole thing more
straightforward by making the passed in bpp value .4 binary
fixed point always, instead of having to pass in different
things based on whether DSC is enabled or not.
v2:
- Fix DSC kunit test cases.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: David Francis <David.Francis@amd.com>
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Fixes: dc48529fb14e ("drm/dp_mst: Add PBN calculation for DSC modes")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Imre: Fix kunit test cases]
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231030155843.2251023-3-imre.deak@intel.com
kernel:
- add initial vmemdup-user-array
core:
- fix platform remove() to return void
- drm_file owner updated to reflect owner
- move size calcs to drm buddy allocator
- let GPUVM build as a module
- allow variable number of run-queues in scheduler
edid:
- handle bad h/v sync_end in EDIDs
panfrost:
- add Boris as maintainer
fbdev:
- use fb_ops helpers more
- only allow logo use from fbcon
- rename fb_pgproto to pgprot_framebuffer
- add HPD state to drm_connector_oob_hotplug_event
- convert to fbdev i/o mem helpers
i915:
- Enable meteorlake by default
- Early Xe2 LPD/Lunarlake display enablement
- Rework subplatforms into IP version checks
- GuC based TLB invalidation for Meteorlake
- Display rework for future Xe driver integration
- LNL FBC features
- LNL display feature capability reads
- update recommended fw versions for DG2+
- drop fastboot module parameter
- added deviceid for Arrowlake-S
- drop preproduction workarounds
- don't disable preemption for resets
- cleanup inlines in headers
- PXP firmware loading fix
- Fix sg list lengths
- DSC PPS state readout/verification
- Add more RPL P/U PCI IDs
- Add new DG2-G12 stepping
- DP enhanced framing support to state checker
- Improve shared link bandwidth management
- stop using GEM macros in display code
- refactor related code into display code
- locally enable W=1 warnings
- remove PSR watchdog timers on LNL
amdgpu:
- RAS/FRU EEPROM updatse
- IP discovery updatses
- GC 11.5 support
- DCN 3.5 support
- VPE 6.1 support
- NBIO 7.11 support
- DML2 support
- lots of IP updates
- use flexible arrays for bo list handling
- W=1 fixes
- Enable seamless boot in more cases
- Enable context type property for HDMI
- Rework GPUVM TLB flushing
- VCN IB start/size alignment fixes
amdkfd:
- GC 10/11 fixes
- GC 11.5 support
- use partial migration in GPU faults
radeon:
- W=1 Fixes
- fix some possible buffer overflow/NULL derefs
nouveau:
- update uapi for NO_PREFETCH
- scheduler/fence fixes
- rework suspend/resume for GSP-RM
- rework display in preparation for GSP-RM
habanalabs:
- uapi: expose tsc clock
- uapi: block access to eventfd through control device
- uapi: force dma-buf export to PAGE_SIZE alignments
- complete move to accel subsystem
- move firmware interface include files
- perform hard reset on PCIe AXI drain event
- optimise user interrupt handling
msm:
- DP: use existing helpers for DPCD
- DPU: interrupts reworked
- gpu: a7xx (a730/a740) support
- decouple msm_drv from kms for headless devices
mediatek:
- MT8188 dsi/dp/edp support
- DDP GAMMA - 12 bit LUT support
- connector dynamic selection capability
rockchip:
- rv1126 mipi-dsi/vop support
- add planar formats
ast:
- rename constants
panels:
- Mitsubishi AA084XE01
- JDI LPM102A188A
- LTK050H3148W-CTA6
ivpu:
- power management fixes
qaic:
- add detach slice bo api
komeda:
- add NV12 writeback
tegra:
- support NVSYNC/NHSYNC
- host1x suspend fixes
ili9882t:
- separate into own driver
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEEKbZHaGwW9KfbeusDHTzWXnEhr4FAmVAgzYACgkQDHTzWXnE
hr7ZEQ//UXne3tyGOsU3X8r+lstLFDMa90a3hvTg6hX+Q0MjHd/clwkKFkLpkipL
n7gIZlaHl11dRs0FzrIZA5EVAAgjMLKmIl10NBDFec6ZFA3VERcggx8y61uifI15
VviMR1VbLHYZaCdyrQOK0A4wcktWnKXyoXp7cwy9crdc2GOBMUZkdIqtvD7jHxQx
UMIFnzi1CyKUX/Fjt/JceYcNk9y2ZGkzakYO3sHcUdv4DPu9qX4kNzpjF691AZBP
UeKWvCswTRVg2M0kuo/RYIBzqaTmOlk6dHLWBognIeZPyuyhCcaGC2d64c6tShwQ
dtHdi+IgyQ8s2qb350ymKTQUP7xA/DfZBwH7LvrZALBxeQGYQN1CnsgDMOS2wcUc
XrRFiS7PxEOtMMBctcPBnnoV5ttnsLLlPpzM9puh9sUFMn6CgLzcAMqXdqxzMajH
+dz2aD1N0vMqq4varozOg9SC2QamgUiPN/TQfrulhCTCfQaXczy5x1OYiIz65+Sl
mKoe2WASuP9Ve8do4N/wEwH5SZY2ItipBdUTRxttY9NTanmV0X5DjZBXH5b9XGci
Zl5Ar613f9zwm5T5BVA5k6s3ZbGY6QcP5pDNTCPaSgitfFXIdReBZ2CaYzK3MPg/
Wit/TXrud9yT6VPpI1igboMyasf5QubV1MY1K83kOCWr9u8R2CM=
=l79u
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2023-10-31-1' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Highlights:
- AMD adds some more upcoming HW platforms
- Intel made Meteorlake stable and started adding Lunarlake
- nouveau has a bunch of display rework in prepartion for the NVIDIA
GSP firmware support
- msm adds a7xx support
- habanalabs has finished migration to accel subsystem
Detail summary:
kernel:
- add initial vmemdup-user-array
core:
- fix platform remove() to return void
- drm_file owner updated to reflect owner
- move size calcs to drm buddy allocator
- let GPUVM build as a module
- allow variable number of run-queues in scheduler
edid:
- handle bad h/v sync_end in EDIDs
panfrost:
- add Boris as maintainer
fbdev:
- use fb_ops helpers more
- only allow logo use from fbcon
- rename fb_pgproto to pgprot_framebuffer
- add HPD state to drm_connector_oob_hotplug_event
- convert to fbdev i/o mem helpers
i915:
- Enable meteorlake by default
- Early Xe2 LPD/Lunarlake display enablement
- Rework subplatforms into IP version checks
- GuC based TLB invalidation for Meteorlake
- Display rework for future Xe driver integration
- LNL FBC features
- LNL display feature capability reads
- update recommended fw versions for DG2+
- drop fastboot module parameter
- added deviceid for Arrowlake-S
- drop preproduction workarounds
- don't disable preemption for resets
- cleanup inlines in headers
- PXP firmware loading fix
- Fix sg list lengths
- DSC PPS state readout/verification
- Add more RPL P/U PCI IDs
- Add new DG2-G12 stepping
- DP enhanced framing support to state checker
- Improve shared link bandwidth management
- stop using GEM macros in display code
- refactor related code into display code
- locally enable W=1 warnings
- remove PSR watchdog timers on LNL
amdgpu:
- RAS/FRU EEPROM updatse
- IP discovery updatses
- GC 11.5 support
- DCN 3.5 support
- VPE 6.1 support
- NBIO 7.11 support
- DML2 support
- lots of IP updates
- use flexible arrays for bo list handling
- W=1 fixes
- Enable seamless boot in more cases
- Enable context type property for HDMI
- Rework GPUVM TLB flushing
- VCN IB start/size alignment fixes
amdkfd:
- GC 10/11 fixes
- GC 11.5 support
- use partial migration in GPU faults
radeon:
- W=1 Fixes
- fix some possible buffer overflow/NULL derefs
nouveau:
- update uapi for NO_PREFETCH
- scheduler/fence fixes
- rework suspend/resume for GSP-RM
- rework display in preparation for GSP-RM
habanalabs:
- uapi: expose tsc clock
- uapi: block access to eventfd through control device
- uapi: force dma-buf export to PAGE_SIZE alignments
- complete move to accel subsystem
- move firmware interface include files
- perform hard reset on PCIe AXI drain event
- optimise user interrupt handling
msm:
- DP: use existing helpers for DPCD
- DPU: interrupts reworked
- gpu: a7xx (a730/a740) support
- decouple msm_drv from kms for headless devices
mediatek:
- MT8188 dsi/dp/edp support
- DDP GAMMA - 12 bit LUT support
- connector dynamic selection capability
rockchip:
- rv1126 mipi-dsi/vop support
- add planar formats
ast:
- rename constants
panels:
- Mitsubishi AA084XE01
- JDI LPM102A188A
- LTK050H3148W-CTA6
ivpu:
- power management fixes
qaic:
- add detach slice bo api
komeda:
- add NV12 writeback
tegra:
- support NVSYNC/NHSYNC
- host1x suspend fixes
ili9882t:
- separate into own driver"
* tag 'drm-next-2023-10-31-1' of git://anongit.freedesktop.org/drm/drm: (1803 commits)
drm/amdgpu: Remove unused variables from amdgpu_show_fdinfo
drm/amdgpu: Remove duplicate fdinfo fields
drm/amd/amdgpu: avoid to disable gfxhub interrupt when driver is unloaded
drm/amdgpu: Add EXT_COHERENT support for APU and NUMA systems
drm/amdgpu: Retrieve CE count from ce_count_lo_chip in EccInfo table
drm/amdgpu: Identify data parity error corrected in replay mode
drm/amdgpu: Fix typo in IP discovery parsing
drm/amd/display: fix S/G display enablement
drm/amdxcp: fix amdxcp unloads incompletely
drm/amd/amdgpu: fix the GPU power print error in pm info
drm/amdgpu: Use pcie domain of xcc acpi objects
drm/amd: check num of link levels when update pcie param
drm/amdgpu: Add a read to GFX v9.4.3 ring test
drm/amd/pm: call smu_cmn_get_smc_version in is_mode1_reset_supported.
drm/amdgpu: get RAS poison status from DF v4_6_2
drm/amdgpu: Use discovery table's subrevision
drm/amd/display: 3.2.256
drm/amd/display: add interface to query SubVP status
drm/amd/display: Read before writing Backlight Mode Set Register
drm/amd/display: Disable SYMCLK32_SE RCO on DCN314
...
As drm_dp_get_mst_branch_device_by_guid() is called from
drm_dp_get_mst_branch_device_by_guid(), mstb parameter has to be checked,
otherwise NULL dereference may occur in the call to
the memcpy() and cause following:
[12579.365869] BUG: kernel NULL pointer dereference, address: 0000000000000049
[12579.365878] #PF: supervisor read access in kernel mode
[12579.365880] #PF: error_code(0x0000) - not-present page
[12579.365882] PGD 0 P4D 0
[12579.365887] Oops: 0000 [#1] PREEMPT SMP NOPTI
...
[12579.365895] Workqueue: events_long drm_dp_mst_up_req_work
[12579.365899] RIP: 0010:memcmp+0xb/0x29
[12579.365921] Call Trace:
[12579.365927] get_mst_branch_device_by_guid_helper+0x22/0x64
[12579.365930] drm_dp_mst_up_req_work+0x137/0x416
[12579.365933] process_one_work+0x1d0/0x419
[12579.365935] worker_thread+0x11a/0x289
[12579.365938] kthread+0x13e/0x14f
[12579.365941] ? process_one_work+0x419/0x419
[12579.365943] ? kthread_blkcg+0x31/0x31
[12579.365946] ret_from_fork+0x1f/0x30
As get_mst_branch_device_by_guid_helper() is recursive, moving condition
to the first line allow to remove a similar one for step over of NULL elements
inside a loop.
Fixes: 5e93b8208d3c ("drm/dp/mst: move GUID storage from mgr, port to only mst branch")
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Lukasz Majczak <lma@semihalf.com>
Reviewed-by: Radoslaw Biernacki <rad@chromium.org>
Signed-off-by: Manasi Navare <navaremanasi@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230922063410.23626-1-lma@semihalf.com
Return an error during payload addition if the payload port isn't
found. This shouldn't change the behavior since only the i915 driver
checks the return value, printing an error message in case of a failure.
While at it simplify the control flow.
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230913223218.540365-2-imre.deak@intel.com
[Why]
Today, the allocation/deallocation steps and status is a bit unclear.
For instance, payload->vc_start_slot = -1 stands for "the failure of
updating DPCD payload ID table" and can also represent as "payload is not
allocated yet". These two cases should be handled differently and hence
better to distinguish them for better understanding.
[How]
Define enumeration - ALLOCATION_LOCAL, ALLOCATION_DFP and ALLOCATION_REMOTE
to distinguish different allocation status. Adjust the code to handle
different status accordingly for better understanding the sequence of
payload allocation and payload removement.
For payload creation, the procedure should look like this:
DRM part 1:
* step 1 - update sw mst mgr variables to add a new payload
* step 2 - add payload at immediate DFP DPCD payload table
Driver:
* Add new payload in HW and sync up with DFP by sending ACT
DRM Part 2:
* Send ALLOCATE_PAYLOAD sideband message to allocate bandwidth along the
virtual channel.
And as for payload removement, the procedure should look like this:
DRM part 1:
* step 1 - Send ALLOCATE_PAYLOAD sideband message to release bandwidth
along the virtual channel
* step 2 - Clear payload allocation at immediate DFP DPCD payload table
Driver:
* Remove the payload in HW and sync up with DFP by sending ACT
DRM part 2:
* update sw mst mgr variables to remove the payload
Note that it's fine to fail when communicate with the branch device
connected at immediate downstrean-facing port, but updating variables of
SW mst mgr and HW configuration should be conducted anyway. That's because
it's under commit_tail and we need to complete the HW programming.
Changes since v1:
* Remove the set but not use variable 'old_payload' in function
'nv50_msto_prepare'. Catched by kernel test robot <lkp@intel.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230807025639.1612361-3-Wayne.Lin@amd.com
[Why]
There is no need to consider payload->delete case since we won't call
drm_dp_add_payload_part2() to create a payload when we're about to
remove it.
[How]
Delete unnecessary case to simplify the code.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230807025639.1612361-2-Wayne.Lin@amd.com
Connectors have source physical address available in display
info. There's no need to parse the EDID again for this. Add
drm_dp_cec_attach() to do this.
Seems like the set_edid/unset_edid naming is a bit specific now that
there's no need to pass the EDID at all, so aim for attach/detach going
forward.
v2: Fix the embarrashing build failures
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: linux-media@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230825130120.1250089-1-jani.nikula@intel.com
As per DP v1.4, a DP DSC Sink device shall support 8bpc in DPCD 6Ah.
Apparently some panels that do support DSC, are not setting the bit for
8bpc.
So always assume 8bpc support by DSC decoder, when DSC is claimed to be
supported.
v2: Use helper to get check dsc support. (Ankit)
v3: Fix styling and other typos. (Jani)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230824125121.840298-2-ankit.k.nautiyal@intel.com
UAPI Changes:
* fbdev:
* Make fbdev userspace interfaces optional; only leaves the
framebuffer console active
* prime:
* Support dma-buf self-import for all drivers automatically: improves
support for many userspace compositors
Cross-subsystem Changes:
* backlight:
* Fix interaction with fbdev in several drivers
* base: Convert struct platform.remove to return void; part of a larger,
tree-wide effort
* dma-buf: Acquire reservation lock for mmap() in exporters; part
of an on-going effort to simplify locking around dma-bufs
* fbdev:
* Use Linux device instead of fbdev device in many places
* Use deferred-I/O helper macros in various drivers
* i2c: Convert struct i2c from .probe_new to .probe; part of a larger,
tree-wide effort
* video:
* Avoid including <linux/screen_info.h>
Core Changes:
* atomic:
* Improve logging
* prime:
* Remove struct drm_driver.gem_prime_mmap plus driver updates: all
drivers now implement this callback with drm_gem_prime_mmap()
* gem:
* Support execution contexts: provides locking over multiple GEM
objects
* ttm:
* Support init_on_free
* Swapout fixes
Driver Changes:
* accel:
* ivpu: MMU updates; Support debugfs
* ast:
* Improve device-model detection
* Cleanups
* bridge:
* dw-hdmi: Improve support for YUV420 bus format
* dw-mipi-dsi: Fix enable/disable of DSI controller
* lt9611uxc: Use MODULE_FIRMWARE()
* ps8640: Remove broken EDID code
* samsung-dsim: Fix command transfer
* tc358764: Handle HS/VS polarity; Use BIT() macro; Various cleanups
* Cleanups
* ingenic:
* Kconfig REGMAP fixes
* loongson:
* Support display controller
* mgag200:
* Minor fixes
* mxsfb:
* Support disabling overlay planes
* nouveau:
* Improve VRAM detection
* Various fixes and cleanups
* panel:
* panel-edp: Support AUO B116XAB01.4
* Support Visionox R66451 plus DT bindings
* Cleanups
* ssd130x:
* Support per-controller default resolution plus DT bindings
* Reduce memory-allocation overhead
* Cleanups
* tidss:
* Support TI AM625 plus DT bindings
* Implement new connector model plus driver updates
* vkms
* Improve write-back support
* Documentation fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAmSvvRAACgkQaA3BHVML
eiNpGQgAs8jq1XjN9t8jZsdgXnoCbkZyVUI2NO0HwoVwpRCLgbXp5AX5qq2oRciE
TBhe4Fceh/ZsYqHTZQahnguxgRKM5JgXwbI4Z0iiOVcqasNbycaKAqipxJJ7kdo1
qPhGCbgQFVX7oIq2xjfXehh6O0SYX+R9r88X8dMJxMYv/pcLwOHG74kS040WOcQq
uATgcnobOf/D8ZmlqvfKGAeTUoFo/RSR2Uhlauka58qgeUbicrTELZT2barY9d+k
as6U5vv4wx2zMklTkjrlkMpAT1ZpbB9d3jGHwL27VEnjlfd3wV2bdH7Dzn9qZRf/
gn0ALg/b3u5yBWk/k7YBvijXyNcH6Q==
=bBuG
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2023-07-13' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.6:
UAPI Changes:
* fbdev:
* Make fbdev userspace interfaces optional; only leaves the
framebuffer console active
* prime:
* Support dma-buf self-import for all drivers automatically: improves
support for many userspace compositors
Cross-subsystem Changes:
* backlight:
* Fix interaction with fbdev in several drivers
* base: Convert struct platform.remove to return void; part of a larger,
tree-wide effort
* dma-buf: Acquire reservation lock for mmap() in exporters; part
of an on-going effort to simplify locking around dma-bufs
* fbdev:
* Use Linux device instead of fbdev device in many places
* Use deferred-I/O helper macros in various drivers
* i2c: Convert struct i2c from .probe_new to .probe; part of a larger,
tree-wide effort
* video:
* Avoid including <linux/screen_info.h>
Core Changes:
* atomic:
* Improve logging
* prime:
* Remove struct drm_driver.gem_prime_mmap plus driver updates: all
drivers now implement this callback with drm_gem_prime_mmap()
* gem:
* Support execution contexts: provides locking over multiple GEM
objects
* ttm:
* Support init_on_free
* Swapout fixes
Driver Changes:
* accel:
* ivpu: MMU updates; Support debugfs
* ast:
* Improve device-model detection
* Cleanups
* bridge:
* dw-hdmi: Improve support for YUV420 bus format
* dw-mipi-dsi: Fix enable/disable of DSI controller
* lt9611uxc: Use MODULE_FIRMWARE()
* ps8640: Remove broken EDID code
* samsung-dsim: Fix command transfer
* tc358764: Handle HS/VS polarity; Use BIT() macro; Various cleanups
* Cleanups
* ingenic:
* Kconfig REGMAP fixes
* loongson:
* Support display controller
* mgag200:
* Minor fixes
* mxsfb:
* Support disabling overlay planes
* nouveau:
* Improve VRAM detection
* Various fixes and cleanups
* panel:
* panel-edp: Support AUO B116XAB01.4
* Support Visionox R66451 plus DT bindings
* Cleanups
* ssd130x:
* Support per-controller default resolution plus DT bindings
* Reduce memory-allocation overhead
* Cleanups
* tidss:
* Support TI AM625 plus DT bindings
* Implement new connector model plus driver updates
* vkms
* Improve write-back support
* Documentation fixes
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230713090830.GA23281@linux-uq9g
core:
- replace strlcpy with strscpy
- EDID changes to support further conversion to struct drm_edid
- Move i915 DSC parameter code to common DRM helpers
- Add Colorspace functionality
aperture:
- ignore framebuffers with non-primary devices
fbdev:
- use fbdev i/o helpers
- add Kconfig options for fb_ops helpers
- use new fb io helpers directly in drivers
sysfs:
- export DRM connector ID
scheduler:
- Avoid an infinite loop
ttm:
- store function table in .rodata
- Add query for TTM mem limit
- Add NUMA awareness to pools
- Export ttm_pool_fini()
bridge:
- fsl-ldb: support i.MX6SX
- lt9211, lt9611: remove blanking packets
- tc358768: implement input bus formats, devm cleanups
- ti-snd65dsi86: implement wait_hpd_asserted
- analogix: fix endless probe loop
- samsung-dsim: support swapped clock, fix enabling, support var clock
- display-connector: Add support for external power supply
- imx: Fix module linking
- tc358762: Support reset GPIO
panel:
- nt36523: Support Lenovo J606F
- st7703: Support Anbernic RG353V-V2
- InnoLux G070ACE-L01 support
- boe-tv101wum-nl6: Improve initialization
- sharp-ls043t1le001: Mode fixes
- simple: BOE EV121WXM-N10-1850, S6D7AA0
- Ampire AM-800480L1TMQW-T00H
- Rocktech RK043FN48H
- Starry himax83102-j02
- Starry ili9882t
amdgpu:
- add new ctx query flag to handle reset better
- add new query/set shadow buffer for rdna3
- DCN 3.2/3.1.x/3.0.x updates
- Enable DC_FP on loongarch
- PCIe fix for RDNA2
- improve DC FAMS/SubVP support for better power management
- partition support for lots of engines
- Take NUMA into account when allocating memory
- Add new DRM_AMDGPU_WERROR config parameter to help with CI
- Initial SMU13 overdrive support
- Add support for new colorspace KMS API
- W=1 fixes
amdkfd:
- Query TTM mem limit rather than hardcoding it
- GC 9.4.3 partition support
- Handle NUMA for partitions
- Add debugger interface for enabling gdb
- Add KFD event age tracking
radeon:
- Fix possible UAF
i915:
- new getparam for PXP support
- GSC/MEI proxy driver
- Meteorlake display enablement
- avoid clearing preallocated framebuffers with TTM
- implement framebuffer mmap support
- Disable sampler indirect state in bindless heap
- Enable fdinfo for GuC backends
- GuC loading and firmware table handling fixes
- Various refactors for multi-tile enablement
- Define MOCS and PAT tables for MTL
- GSC/MEI support for Meteorlake
- PMU multi-tile support
- Large driver kernel doc cleanup
- Allow VRR toggling and arbitrary refresh rates
- Support async flips on linear buffers on display ver 12+
- Expose CRTC CTM property on ILK/SNB/VLV
- New debugfs for display clock frequencies
- Hotplug refactoring
- Display refactoring
- I915_GEM_CREATE_EXT_SET_PAT for Mesa on Meteorlake
- Use large rings for compute contexts
- HuC loading for MTL
- Allow user to set cache at BO creation
- MTL powermanagement enhancements
- Switch to dedicated workqueues to stop using flush_scheduled_work()
- Move display runtime init under display/
- Remove 10bit gamma on desktop gen3 parts, they don't support it
habanalabs:
- uapi: return 0 for user queries if there was a h/w or f/w error
- Add pci health check when we lose connection with the firmware. This can be used to
distinguish between pci link down and firmware getting stuck.
- Add more info to the error print when TPC interrupt occur.
- Firmware fixes
msm:
- Adreno A660 bindings
- SM8350 MDSS bindings fix
- Added support for DPU on sm6350 and sm6375 platforms
- Implemented tearcheck support to support vsync on SM150 and newer platforms
- Enabled missing features (DSPP, DSC, split display) on sc8180x, sc8280xp, sm8450
- Added support for DSI and 28nm DSI PHY on MSM8226 platform
- Added support for DSI on sm6350 and sm6375 platforms
- Added support for display controller on MSM8226 platform
- A690 GPU support
- Move cmdstream dumping out of fence signaling path
- a610 support
- Support for a6xx devices without GMU
nouveau:
- NULL ptr before deref fixes
armada:
- implement fbdev emulation as client
sun4i:
- fix mipi-dsi dotclock
- release clocks
vc4:
- rgb range toggle property
- BT601 / BT2020 HDMI support
vkms:
- convert to drmm helpers
- add reflection and rotation support
- fix rgb565 conversion
gma500:
- fix iomem access
shmobile:
- support renesas soc platform
- enable fbdev
mxsfb:
- Add support for i.MX93 LCDIF
stm:
- dsi: Use devm_ helper
- ltdc: Fix potential invalid pointer deref
renesas:
- Group drivers in renesas subdirectory to prepare for new platform
- Drop deprecated R-Car H3 ES1.x support
meson:
- Add support for MIPI DSI displays
virtio:
- add sync object support
mediatek:
- Add display binding document for MT6795
-----BEGIN PGP SIGNATURE-----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=FmUA
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2023-06-29' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"There is one set of patches to misc for a i915 gsc/mei proxy driver.
Otherwise it's mostly amdgpu/i915/msm, lots of hw enablement and lots
of refactoring.
core:
- replace strlcpy with strscpy
- EDID changes to support further conversion to struct drm_edid
- Move i915 DSC parameter code to common DRM helpers
- Add Colorspace functionality
aperture:
- ignore framebuffers with non-primary devices
fbdev:
- use fbdev i/o helpers
- add Kconfig options for fb_ops helpers
- use new fb io helpers directly in drivers
sysfs:
- export DRM connector ID
scheduler:
- Avoid an infinite loop
ttm:
- store function table in .rodata
- Add query for TTM mem limit
- Add NUMA awareness to pools
- Export ttm_pool_fini()
bridge:
- fsl-ldb: support i.MX6SX
- lt9211, lt9611: remove blanking packets
- tc358768: implement input bus formats, devm cleanups
- ti-snd65dsi86: implement wait_hpd_asserted
- analogix: fix endless probe loop
- samsung-dsim: support swapped clock, fix enabling, support var
clock
- display-connector: Add support for external power supply
- imx: Fix module linking
- tc358762: Support reset GPIO
panel:
- nt36523: Support Lenovo J606F
- st7703: Support Anbernic RG353V-V2
- InnoLux G070ACE-L01 support
- boe-tv101wum-nl6: Improve initialization
- sharp-ls043t1le001: Mode fixes
- simple: BOE EV121WXM-N10-1850, S6D7AA0
- Ampire AM-800480L1TMQW-T00H
- Rocktech RK043FN48H
- Starry himax83102-j02
- Starry ili9882t
amdgpu:
- add new ctx query flag to handle reset better
- add new query/set shadow buffer for rdna3
- DCN 3.2/3.1.x/3.0.x updates
- Enable DC_FP on loongarch
- PCIe fix for RDNA2
- improve DC FAMS/SubVP support for better power management
- partition support for lots of engines
- Take NUMA into account when allocating memory
- Add new DRM_AMDGPU_WERROR config parameter to help with CI
- Initial SMU13 overdrive support
- Add support for new colorspace KMS API
- W=1 fixes
amdkfd:
- Query TTM mem limit rather than hardcoding it
- GC 9.4.3 partition support
- Handle NUMA for partitions
- Add debugger interface for enabling gdb
- Add KFD event age tracking
radeon:
- Fix possible UAF
i915:
- new getparam for PXP support
- GSC/MEI proxy driver
- Meteorlake display enablement
- avoid clearing preallocated framebuffers with TTM
- implement framebuffer mmap support
- Disable sampler indirect state in bindless heap
- Enable fdinfo for GuC backends
- GuC loading and firmware table handling fixes
- Various refactors for multi-tile enablement
- Define MOCS and PAT tables for MTL
- GSC/MEI support for Meteorlake
- PMU multi-tile support
- Large driver kernel doc cleanup
- Allow VRR toggling and arbitrary refresh rates
- Support async flips on linear buffers on display ver 12+
- Expose CRTC CTM property on ILK/SNB/VLV
- New debugfs for display clock frequencies
- Hotplug refactoring
- Display refactoring
- I915_GEM_CREATE_EXT_SET_PAT for Mesa on Meteorlake
- Use large rings for compute contexts
- HuC loading for MTL
- Allow user to set cache at BO creation
- MTL powermanagement enhancements
- Switch to dedicated workqueues to stop using flush_scheduled_work()
- Move display runtime init under display/
- Remove 10bit gamma on desktop gen3 parts, they don't support it
habanalabs:
- uapi: return 0 for user queries if there was a h/w or f/w error
- Add pci health check when we lose connection with the firmware.
This can be used to distinguish between pci link down and firmware
getting stuck.
- Add more info to the error print when TPC interrupt occur.
- Firmware fixes
msm:
- Adreno A660 bindings
- SM8350 MDSS bindings fix
- Added support for DPU on sm6350 and sm6375 platforms
- Implemented tearcheck support to support vsync on SM150 and newer
platforms
- Enabled missing features (DSPP, DSC, split display) on sc8180x,
sc8280xp, sm8450
- Added support for DSI and 28nm DSI PHY on MSM8226 platform
- Added support for DSI on sm6350 and sm6375 platforms
- Added support for display controller on MSM8226 platform
- A690 GPU support
- Move cmdstream dumping out of fence signaling path
- a610 support
- Support for a6xx devices without GMU
nouveau:
- NULL ptr before deref fixes
armada:
- implement fbdev emulation as client
sun4i:
- fix mipi-dsi dotclock
- release clocks
vc4:
- rgb range toggle property
- BT601 / BT2020 HDMI support
vkms:
- convert to drmm helpers
- add reflection and rotation support
- fix rgb565 conversion
gma500:
- fix iomem access
shmobile:
- support renesas soc platform
- enable fbdev
mxsfb:
- Add support for i.MX93 LCDIF
stm:
- dsi: Use devm_ helper
- ltdc: Fix potential invalid pointer deref
renesas:
- Group drivers in renesas subdirectory to prepare for new platform
- Drop deprecated R-Car H3 ES1.x support
meson:
- Add support for MIPI DSI displays
virtio:
- add sync object support
mediatek:
- Add display binding document for MT6795"
* tag 'drm-next-2023-06-29' of git://anongit.freedesktop.org/drm/drm: (1791 commits)
drm/i915: Fix a NULL vs IS_ERR() bug
drm/i915: make i915_drm_client_fdinfo() reference conditional again
drm/i915/huc: Fix missing error code in intel_huc_init()
drm/i915/gsc: take a wakeref for the proxy-init-completion check
drm/msm/a6xx: Add A610 speedbin support
drm/msm/a6xx: Add A619_holi speedbin support
drm/msm/a6xx: Use adreno_is_aXYZ macros in speedbin matching
drm/msm/a6xx: Use "else if" in GPU speedbin rev matching
drm/msm/a6xx: Fix some A619 tunables
drm/msm/a6xx: Add A610 support
drm/msm/a6xx: Add support for A619_holi
drm/msm/adreno: Disable has_cached_coherent in GMU wrapper configurations
drm/msm/a6xx: Introduce GMU wrapper support
drm/msm/a6xx: Move CX GMU power counter enablement to hw_init
drm/msm/a6xx: Extend and explain UBWC config
drm/msm/a6xx: Remove both GBIF and RBBM GBIF halt on hw init
drm/msm/a6xx: Add a helper for software-resetting the GPU
drm/msm/a6xx: Improve a6xx_bus_clear_pending_transactions()
drm/msm/a6xx: Move a6xx_bus_clear_pending_transactions to a6xx_gpu
drm/msm/a6xx: Move force keepalive vote removal to a6xx_gmu_force_off()
...
- Fix KMSAN vs FORTIFY in strlcpy/strlcat (Alexander Potapenko)
- Convert strreplace() to return string start (Andy Shevchenko)
- Flexible array conversions (Arnd Bergmann, Wyes Karny, Kees Cook)
- Add missing function prototypes seen with W=1 (Arnd Bergmann)
- Fix strscpy() kerndoc typo (Arne Welzel)
- Replace strlcpy() with strscpy() across many subsystems which were
either Acked by respective maintainers or were trivial changes that
went ignored for multiple weeks (Azeem Shaikh)
- Remove unneeded cc-option test for UBSAN_TRAP (Nick Desaulniers)
- Add KUnit tests for strcat()-family
- Enable KUnit tests of FORTIFY wrappers under UML
- Add more complete FORTIFY protections for strlcat()
- Add missed disabling of FORTIFY for all arch purgatories.
- Enable -fstrict-flex-arrays=3 globally
- Tightening UBSAN_BOUNDS when using GCC
- Improve checkpatch to check for strcpy, strncpy, and fake flex arrays
- Improve use of const variables in FORTIFY
- Add requested struct_size_t() helper for types not pointers
- Add __counted_by macro for annotating flexible array size members
-----BEGIN PGP SIGNATURE-----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=s0j1
-----END PGP SIGNATURE-----
Merge tag 'hardening-v6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
"There are three areas of note:
A bunch of strlcpy()->strscpy() conversions ended up living in my tree
since they were either Acked by maintainers for me to carry, or got
ignored for multiple weeks (and were trivial changes).
The compiler option '-fstrict-flex-arrays=3' has been enabled
globally, and has been in -next for the entire devel cycle. This
changes compiler diagnostics (though mainly just -Warray-bounds which
is disabled) and potential UBSAN_BOUNDS and FORTIFY _warning_
coverage. In other words, there are no new restrictions, just
potentially new warnings. Any new FORTIFY warnings we've seen have
been fixed (usually in their respective subsystem trees). For more
details, see commit df8fc4e934c12b.
The under-development compiler attribute __counted_by has been added
so that we can start annotating flexible array members with their
associated structure member that tracks the count of flexible array
elements at run-time. It is possible (likely?) that the exact syntax
of the attribute will change before it is finalized, but GCC and Clang
are working together to sort it out. Any changes can be made to the
macro while we continue to add annotations.
As an example of that last case, I have a treewide commit waiting with
such annotations found via Coccinelle:
https://git.kernel.org/linus/adc5b3cb48a049563dc673f348eab7b6beba8a9b
Also see commit dd06e72e68bcb4 for more details.
Summary:
- Fix KMSAN vs FORTIFY in strlcpy/strlcat (Alexander Potapenko)
- Convert strreplace() to return string start (Andy Shevchenko)
- Flexible array conversions (Arnd Bergmann, Wyes Karny, Kees Cook)
- Add missing function prototypes seen with W=1 (Arnd Bergmann)
- Fix strscpy() kerndoc typo (Arne Welzel)
- Replace strlcpy() with strscpy() across many subsystems which were
either Acked by respective maintainers or were trivial changes that
went ignored for multiple weeks (Azeem Shaikh)
- Remove unneeded cc-option test for UBSAN_TRAP (Nick Desaulniers)
- Add KUnit tests for strcat()-family
- Enable KUnit tests of FORTIFY wrappers under UML
- Add more complete FORTIFY protections for strlcat()
- Add missed disabling of FORTIFY for all arch purgatories.
- Enable -fstrict-flex-arrays=3 globally
- Tightening UBSAN_BOUNDS when using GCC
- Improve checkpatch to check for strcpy, strncpy, and fake flex
arrays
- Improve use of const variables in FORTIFY
- Add requested struct_size_t() helper for types not pointers
- Add __counted_by macro for annotating flexible array size members"
* tag 'hardening-v6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (54 commits)
netfilter: ipset: Replace strlcpy with strscpy
uml: Replace strlcpy with strscpy
um: Use HOST_DIR for mrproper
kallsyms: Replace all non-returning strlcpy with strscpy
sh: Replace all non-returning strlcpy with strscpy
of/flattree: Replace all non-returning strlcpy with strscpy
sparc64: Replace all non-returning strlcpy with strscpy
Hexagon: Replace all non-returning strlcpy with strscpy
kobject: Use return value of strreplace()
lib/string_helpers: Change returned value of the strreplace()
jbd2: Avoid printing outside the boundary of the buffer
checkpatch: Check for 0-length and 1-element arrays
riscv/purgatory: Do not use fortified string functions
s390/purgatory: Do not use fortified string functions
x86/purgatory: Do not use fortified string functions
acpi: Replace struct acpi_table_slit 1-element array with flex-array
clocksource: Replace all non-returning strlcpy with strscpy
string: use __builtin_memcpy() in strlcpy/strlcat
staging: most: Replace all non-returning strlcpy with strscpy
drm/i2c: tda998x: Replace all non-returning strlcpy with strscpy
...
Rename drm_sysfs_connector_status_event() to
drm_sysfs_connector_property_event(). Indeed, "status" is a bit
vague: it can easily be confused with the connected/disconnected
status of the connector. This function has nothing to do with
connected/disconnected: it merely sends a notification that a
connector's property has changed (e.g. HDCP, privacy screen, etc).
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Manasi Navare <navaremanasi@chromium.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230620174231.260335-1-contact@emersion.fr
I've been experiencing some intermittent crashes down in the display
driver code. The symptoms are ususally a line like this in dmesg:
amdgpu 0000:30:00.0: [drm] Failed to create MST payload for port 000000006d3a3885: -5
...followed by an Oops due to a NULL pointer dereference.
Switch to using mgr->dev instead of state->dev since "state" can be
NULL in some cases.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2184855
Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230419112447.18471-1-jlayton@kernel.org
Updates for v6.5.. this includes a backmerg of drm-next tree to be able
to use new DRM DSC helpers.
Core:
+ Add Marijn Suijten as drm/msm reviewer
+ Adreno A660 bindings
+ SM8350 MDSS bindings fix
+ Fix adreno_is_a690() warnings
+ More generic (DRM) and MSM-specific DSC helpers
DP:
+ Removed obsolete USB-PD remains
+ Documented DP compatible string for sm8550 platform
DPU:
+ Enable missing features (DSPP, DSC, split display) on sc8180x,
sc8280xp, sm8450
+ Enabled writeback on sc7280
+ Implemented tearcheck support to support vsync on SM150 and
newer platforms
+ Native HDMI output support
+ Dropped unused features: regdma, GC, IGC
+ Fixed the DSC flush operations
+ Simplified QoS handling, removing obsolete and unused features
and merging SSPP and WB code paths
+ Reworked dpu_encoder initialisation path
+ Enabled DSPP support on sdm845
+ Disabled color-management if DSPP blocks are not available
+ Added support for DSC 1.2 blocks found on sm8350 and later
+ Added .fb_dirty to fix CMD panels
DSI:
+ Drop powerup quirks in favour of using pre_enable_prev_first for
downstream bridges
+ Fixed 14nm DSI PHY programming
+ Added support for DSI and 28nm DSI PHY on MSM8226 platform
+ Make use of DRM and MSM DSC helpers
MDP5:
+ Added support for display controller on MSM8226 platform
GPU:
+ A690 support
+ Don't set IO_PGTABLE_QUIRK_ARM_OUTER_WBWA on devices with coherent SMMU
(like A690)
+ Move cmdstream dumping out of fence signaling path
+ Cleanups
+ Support for a6xx devices without GMU (aka "GMU wrapper"
+ a610 support
+ a619_holi support (a619 variant without GMU)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGsUB=tRB4nR6ZCJMuLhro5zN3BQWUSywVYbaipqqDZ_cQ@mail.gmail.com
[Why]
The sequence for collecting down_reply from source perspective should
be:
Request_n->repeat (get partial reply of Request_n->clear message ready
flag to ack DPRX that the message is received) till all partial
replies for Request_n are received->new Request_n+1.
Now there is chance that drm_dp_mst_hpd_irq() will fire new down
request in the tx queue when the down reply is incomplete. Source is
restricted to generate interveleaved message transactions so we should
avoid it.
Also, while assembling partial reply packets, reading out DPCD DOWN_REP
Sideband MSG buffer + clearing DOWN_REP_MSG_RDY flag should be
wrapped up as a complete operation for reading out a reply packet.
Kicking off a new request before clearing DOWN_REP_MSG_RDY flag might
be risky. e.g. If the reply of the new request has overwritten the
DPRX DOWN_REP Sideband MSG buffer before source writing one to clear
DOWN_REP_MSG_RDY flag, source then unintentionally flushes the reply
for the new request. Should handle the up request in the same way.
[How]
Separete drm_dp_mst_hpd_irq() into 2 steps. After acking the MST IRQ
event, driver calls drm_dp_mst_hpd_irq_send_new_request() and might
trigger drm_dp_mst_kick_tx() only when there is no on going message
transaction.
Changes since v1:
* Reworked on review comments received
-> Adjust the fix to let driver explicitly kick off new down request
when mst irq event is handled and acked
-> Adjust the commit message
Changes since v2:
* Adjust the commit message
* Adjust the naming of the divided 2 functions and add a new input
parameter "ack".
* Adjust code flow as per review comments.
Changes since v3:
* Update the function description of drm_dp_mst_hpd_irq_handle_event
Changes since v4:
* Change ack of drm_dp_mst_hpd_irq_handle_event() to be an array align
the size of esi[]
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a helper setting config values which are typically constant across
operating modes (table E-4 of the standard) and mux_word_size (which is
a const according to 3.5.2).
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/539280/
Link: https://lore.kernel.org/r/20230329-rfc-msm-dsc-helper-v14-2-bafc7be95691@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Convert the topology manager to use struct drm_edid, add
drm_dp_mst_edid_read() that returns drm_edid, and rewrite the old
drm_dp_mst_get_edid() to use it.
Note that the old drm_get_edid() ended up calling
drm_connector_update_edid_property(). This responsibility is now
deferred to drivers, which all do it anyway after calling
drm_dp_mst_edid_read() or drm_dp_mst_get_edid().
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9c32e5c241934093fc4144eed4c01155e1f03af1.1685437501.git.jani.nikula@intel.com
Dave Airlie
Douglas Anderson
Imre Deak
Paloma Arellano
Abhinav Kumar
Jani Nikula
Thomas Zimmermann
Ricardo B. Marliere
Bagas Sanjaya
Linus Torvalds
Heiner Kallweit
Daniel Vetter
Ankit Nautiyal
Ville Syrjälä
Lukasz Majczak
Wayne Lin
Simon Ser
Jeff Layton
Jessica Zhang
Dmitry Baryshkov