IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
There's no need to run all the code on mt7530_setup_port5() if port 5 is
disabled. The only case for calling mt7530_setup_port5() from
mt7530_setup() is when PHY muxing is enabled. That is because port 5 is not
defined as a port on the devicetree, therefore, it cannot be controlled by
phylink.
Because of this, run mt7530_setup_port5() if priv->p5_intf_sel is
P5_INTF_SEL_PHY_P0 or P5_INTF_SEL_PHY_P4. Remove the P5_DISABLED case from
mt7530_setup_port5().
Stop initialising the interface variable as the remaining cases will always
call mt7530_setup_port5() with it initialised.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-7-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Running mt7530_setup_port5() from mt7530_setup() used to handle all cases
of configuring port 5, including phylink.
Setting priv->p5_interface under mt7530_setup_port5() makes sure that
mt7530_setup_port5() from mt753x_phylink_mac_config() won't run.
The commit ("net: dsa: mt7530: improve code path for setting up port 5")
makes so that mt7530_setup_port5() from mt7530_setup() runs only on
non-phylink cases.
Get rid of unnecessarily setting priv->p5_interface under
mt7530_setup_port5() as port 5 phylink configuration will be done by
running mt7530_setup_port5() from mt753x_phylink_mac_config() now.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-6-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There're two code paths for setting up port 5:
mt7530_setup()
-> mt7530_setup_port5()
mt753x_phylink_mac_config()
-> mt753x_mac_config()
-> mt7530_mac_config()
-> mt7530_setup_port5()
Currently mt7530_setup_port5() from mt7530_setup() always runs. If port 5
is used as a CPU, DSA, or user port, mt7530_setup_port5() from
mt753x_phylink_mac_config() won't run. That is because priv->p5_interface
set on mt7530_setup_port5() will match state->interface on
mt753x_phylink_mac_config() which will stop running mt7530_setup_port5()
again.
Therefore, mt7530_setup_port5() will never run from
mt753x_phylink_mac_config().
Address this by not running mt7530_setup_port5() from mt7530_setup() if
port 5 is used as a CPU, DSA, or user port. This driver isn't in the
dsa_switches_apply_workarounds[] array so phylink will always be present.
To keep the cases where port 5 isn't controlled by phylink working as
before, preserve the mt7530_setup_port5() call from mt7530_setup().
Do not set priv->p5_intf_sel to P5_DISABLED. It is already set to that when
"priv" is allocated.
Move setting the interface to a more specific location. It's supposed to be
overwritten if PHY muxing is detected.
Improve the comment which explains the process.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-5-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's no logic to numerically order the CPU ports. Just state the port
number instead.
Remove the irrelevant PHY muxing information from
mt7530_mac_port_get_caps(). Explain the supported MII modes instead.
Remove the out of place PHY muxing information from
mt753x_phylink_mac_config(). The function is for MT7530, MT7531, and the
switch on the MT7988 SoC but there's no PHY muxing on MT7531 or the switch
on the MT7988 SoC.
These comments were gradually introduced with the commits below.
commit ca366d6c889b ("net: dsa: mt7530: Convert to PHYLINK API")
commit 38f790a80560 ("net: dsa: mt7530: Add support for port 5")
commit 88bdef8be9f6 ("net: dsa: mt7530: Extend device data ready for adding
a new hardware")
commit c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-4-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce the p5_sgmii field to store the information for whether port 5
has got SGMII or not. Instead of reading the MT7531_TOP_SIG_SR register
multiple times, the register will be read once and the value will be
stored on the p5_sgmii field. This saves unnecessary reads of the
register.
Move the comment about MT7531AE and MT7531BE to mt7531_setup(), where the
switch is identified.
Get rid of mt7531_dual_sgmii_supported() now that priv->p5_sgmii stores the
information. Address the code where mt7531_dual_sgmii_supported() is used.
Get rid of mt7531_is_rgmii_port() which just prints the opposite of
priv->p5_sgmii.
Instead of calling mt7531_pll_setup() then returning, do not call it if
port 5 is SGMII.
Remove P5_INTF_SEL_GMAC5_SGMII. The p5_interface_select enum is supposed to
represent the mode that port 5 is being used in, not the hardware
information of port 5. Set p5_intf_sel to P5_INTF_SEL_GMAC5 instead, if
port 5 is not dsa_is_unused_port().
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-3-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the p5_interface_select enumeration as the data type for the
p5_intf_sel field. This ensures p5_intf_sel can only take the values
defined in the p5_interface_select enumeration.
Remove the explicit assignment of 0 to P5_DISABLED as the first enum item
is automatically assigned 0.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-2-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On the MT7530 switch, the CPU_PORT field indicates which CPU port to trap
frames to, regardless of the affinity of the inbound user port.
When multiple CPU ports are in use, if the DSA conduit interface is down,
trapped frames won't be passed to the conduit interface.
To make trapping frames work including this case, implement
ds->ops->conduit_state_change() on this subdriver and set the CPU_PORT
field to the numerically smallest CPU port whose conduit interface is up.
Introduce the active_cpu_ports field to store the information of the active
CPU ports. Correct the macros, CPU_PORT is bits 4 through 6 of the
register.
Add a comment to explain frame trapping for this switch.
Currently, the driver doesn't support the use of multiple CPU ports so this
is not necessarily a bug fix.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-1-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Correct the PHY loopback bit handling in the ksz8_w_phy_bmcr and
ksz8_r_phy_bmcr functions for KSZ8794 and KSZ8873 variants in the ksz8795
driver. Previously, the code erroneously used Bit 7 of port register 0xD
for both chip variants, which is actually for LED configuration. This
update ensures the correct registers and bits are used for the PHY
loopback feature:
- For KSZ8794: Use 0xF / Bit 7.
- For KSZ8873: Use 0xD / Bit 0.
The lack of loopback support was seen on KSZ8873 system by using
"ethtool -t lanX". After this patch, the ethtool selftest will work,
but only if port is not part of a bridge.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240124123314.734815-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the manual checks for register value changes in the
ksz8_w_phy_bmcr function. Instead, rely on regmap_update_bits() for
optimizing register updates.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240124123314.734815-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Isolate the Basic Mode Control Register (BMCR) operations in the ksz8795
driver by moving the BMCR-related code segments from the ksz8_r_phy()
and ksz8_w_phy() functions to newly created ksz8_r_phy_bmcr() and
ksz8_w_phy_bmcr() functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240124123314.734815-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Quoting from commit 4223f8651287 ("net: dsa: mt7530: make NET_DSA_MT7530
select MEDIATEK_GE_PHY"):
Make MediaTek MT753x DSA driver enable MediaTek Gigabit PHYs driver to
properly control MT7530 and MT7531 switch PHYs.
A noticeable change is that the behaviour of switchport interfaces going
up-down-up-down is no longer there.
Now, the switch can be used without the PHYs but, at the moment, every
hardware design out there that I have seen uses them. For that, it would
make the most sense to force the selection of MEDIATEK_GE_PHY for the MDIO
interface which currently controls the MT7530 and MT7531 switches.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122053451.8004-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Setup PMCR port register for actual speed and duplex on internally
connected PHYs of the MT7988 built-in switch. This fixes links with
speeds other than 1000M.
Fixes: 110c18bfed41 ("net: dsa: mt7530: introduce driver for MT7988 built-in switch")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/a5b04dfa8256d8302f402545a51ac4c626fdba25.1706071272.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the MDIO bus of the switches the MT7530 DSA subdriver controls
can only be registered as non-OF-based. Bring support for registering the
bus OF-based.
The subdrivers that control switches [with MDIO bus] probed on OF must
follow this logic to support all cases properly:
No switch MDIO bus defined: Populate ds->user_mii_bus, register the MDIO
bus, set the interrupts for PHYs if "interrupt-controller" is defined at
the switch node. This case should only be covered for the switches which
their dt-bindings documentation didn't document the MDIO bus from the
start. This is to keep supporting the device trees that do not describe the
MDIO bus on the device tree but the MDIO bus is being used nonetheless.
Switch MDIO bus defined: Don't populate ds->user_mii_bus, register the MDIO
bus, set the interrupts for PHYs if ["interrupt-controller" is defined at
the switch node and "interrupts" is defined at the PHY nodes under the
switch MDIO bus node].
Switch MDIO bus defined but explicitly disabled: If the device tree says
status = "disabled" for the MDIO bus, we shouldn't need an MDIO bus at all.
Instead, just exit as early as possible and do not call any MDIO API.
The use of ds->user_mii_bus is inappropriate when the MDIO bus of the
switch is described on the device tree [1], which is why we don't populate
ds->user_mii_bus in that case.
Link: https://lore.kernel.org/netdev/20231213120656.x46fyad6ls7sqyzv@skbuf/ [1]
Suggested-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122053431.7751-1-arinc.unal@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
devm_kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure.
Fixes: 05bd97fc559d ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240111072018.75971-1-chentao@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There used to be a of_node_put(priv->master_mii_dn) call in
bcm_sf2_mdio_unregister(), which was accidentally deleted in commit
6ca80638b90c ("net: dsa: Use conduit and user terms").
But it's not needed - we don't need to hold a reference on the
"brcm,unimac-mdio" OF node for that long, since we don't do anything
with it. We can release it as soon as we finish bcm_sf2_mdio_register().
Also reduce "if (err && dn)" to just "if (err)". We know "dn", aka the
former priv->master_mii_dn, is non-NULL. Otherwise, of_mdio_find_bus(dn)
would not have been able to find the bus behind "brcm,unimac-mdio".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcm_sf2 driver does something strange. Instead of calling
of_mdiobus_register() with an OF node argument, it manually assigns the
bus->dev->of_node and then calls the non-OF mdiobus_register(). This
circumvents some code from __of_mdiobus_register() from running, which
sets the auto-scan mask, parses some device tree properties, etc.
I'm going to go out on a limb and say that the OF node isn't, in fact,
needed at all, and can be removed. The MDIO diversion as initially
implemented in commit 461cd1b03e32 ("net: dsa: bcm_sf2: Register our
slave MDIO bus") looked quite different than it is now, after commit
771089c2a485 ("net: dsa: bcm_sf2: Ensure that MDIO diversion is used").
Initially, it made sense, as bcm_sf2 was registering another set of
driver ops for the "brcm,unimac-mdio" OF node. But now, it deletes all
phandles, which makes "phy-handle"s unable to find PHYs, which means
that it always goes through the OF-unaware dsa_user_phy_connect().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accessed either through priv->dev or ds->dev, it is the same device
structure. Keep a single variable which holds a reference to it, and use
it consistently.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__of_mdiobus_register() already calls __mdiobus_register() if the
OF node provided as argument is NULL. We can take advantage of that
and simplify the 2 code path, calling devm_of_mdiobus_register() only
once for both cases.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To simplify reasoning about why the DSA framework provides the
ds->user_mii_bus functionality, drivers should only use it if they
need to. The qca8k driver appears to also use it simply as storage
for a pointer, which is not a good enough reason to make the core
much more difficult to follow.
ds->user_mii_bus is useful for only 2 cases:
1. The driver probes on platform_data (no OF)
2. The driver probes on OF, but there is no OF node for the MDIO bus.
It is unclear if case (1) is supported with qca8k. It might not be:
the driver might crash when of_device_get_match_data() returns NULL
and then it dereferences priv->info without NULL checking.
Anyway, let us limit the ds->user_mii_bus usage only to the above cases,
and not assign it when an OF node is present.
The bus->phy_mask assignment follows along with the movement, because
__of_mdiobus_register() overwrites this bus field anyway. The value set
by the driver only matters for the non-OF code path.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver calls the non-OF devm_mdiobus_register() rather
than devm_of_mdiobus_register() for this case, but it seems to rather
be a confusing coincidence, and not a real use case that needs to be
supported.
If the device tree says status = "disabled" for the MDIO bus, we
shouldn't need an MDIO bus at all. Instead, just exit as early as
possible and do not call any MDIO API.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_get_child_by_name() gives us an OF node with an elevated refcount,
which should be dropped when we're done with it. This is so that,
if (of_node_check_flag(node, OF_DYNAMIC)) is true, the node's memory can
eventually be freed.
There are 2 distinct paths to be considered in qca8k_mdio_register():
- devm_of_mdiobus_register() succeeds: since commit 3b73a7b8ec38 ("net:
mdio_bus: add refcounting for fwnodes to mdiobus"), the MDIO core
treats this well.
- devm_of_mdiobus_register() or anything up to that point fails: it is
the duty of the qca8k driver to release the OF node.
This change addresses the second case by making sure that the OF node
reference is not leaked.
The "mdio" node may be NULL, but of_node_put(NULL) is safe.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the "lantiq,xrx200-mdio" child has status = "disabled", the MDIO bus
creation should be avoided. Use of_device_is_available() to check for
that, and take advantage of 2 facts:
- of_device_is_available(NULL) returns false
- of_node_put(NULL) is a no-op
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver does not need any of the functionalities that make
ds->user_mii_bus special. Those use cases are listed here:
https://lore.kernel.org/netdev/20231221174746.hylsmr3f7g5byrsi@skbuf/
It just makes use of ds->user_mii_bus only as storage for its own MDIO
bus, which otherwise has no connection to the framework. This is because:
- the gswip driver only probes on OF: it fails if of_device_get_match_data()
returns NULL
- when the child OF node of the MDIO bus is absent, no MDIO bus is
registered at all, not even by the DSA framework. In order for that to
have happened, the gswip driver would have needed to provide
->phy_read() and ->phy_write() in struct dsa_switch_ops, which it does
not.
We can break the connection between the gswip driver and the DSA
framework and still preserve the same functionality.
Since commit 3b73a7b8ec38 ("net: mdio_bus: add refcounting for fwnodes
to mdiobus"), MDIO buses take ownership of the OF node handled to them,
and release it on their own. The gswip driver no longer needs to do
this.
Combine that with devres, and we no longer need to keep track of
anything for teardown purposes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__of_mdiobus_register(), called right next, overwrites the phy_mask
we just configured on the bus, so this is redundant and confusing.
Delete it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the applicable subset of an mv88e6xxx port's counters using
ethtool's standardized "rmon" counter group.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chips in this family only have one set of histogram counters, which
can be used to count ingressing and/or egressing traffic. mv88e6xxx
has, up until this point, kept the hardware default of counting both
directions.
In the mean time, standard counter group support has been added to
ethtool. Via that interface, drivers may report ingress-only and
egress-only histograms separately - but not combined.
In order for mv88e6xxx to maximize amount of diagnostic information
that can be exported via standard interfaces, we opt to limit the
histogram counters to ingress traffic only. Which will allow us to
export them via the standard "rmon" group in an upcoming commit.
The reason for choosing ingress-only over egress-only, is to be
compatible with RFC2819 (RMON MIB).
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the applicable subset of an mv88e6xxx port's counters using
ethtool's standardized "eth-mac" counter group.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the upcoming standard counter group support, we are no longer
reading out the whole set of counters, but rather mapping a subset to
the requested group.
Therefore, create an enum with an ID for each stat, such that
mv88e6xxx_hw_stats[] can be subscripted with a human-readable ID
corresponding to the counter's name.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_get_stats, which collects stats from various sources,
expects all callees to return the number of stats read. If an error
occurs, 0 should be returned.
Prevent future mishaps of this kind by updating the return type to
reflect this contract.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change contains no functional change. We simply push the hardware
specific stats logic to a function reading a single counter, rather
than the whole set.
This is a preparatory change for the upcoming standard ethtool
statistics support (i.e. "eth-mac", "eth-ctrl" etc.).
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is more consistent with the driver's general structure.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTU callbacks are in layer 1 size, so for example 1500
bytes is a normal setting. Cache this size, and only add
the layer 2 framing right before choosing the setting. On
the CPU port this will however include the DSA tag since
this is transmitted from the parent ethernet interface!
Add the layer 2 overhead such as ethernet and VLAN framing
and FCS before selecting the size in the register.
This will make the code easier to understand.
The rtl8366rb_max_mtu() callback returns a bogus MTU
just subtracting the CPU tag, which is the only thing
we should NOT subtract. Return the correct layer 1
max MTU after removing headers and checksum.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Correct the use of define DSA_TAG_PROTO_LAN937X_VALUE to
DSA_TAG_PROTO_LAN937X to improve readability.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20231206160124.1935451-1-sean@geanix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch converts some basic cases of ethtool_sprintf() to
ethtool_puts().
The conversions are used in cases where ethtool_sprintf() was being used
with just two arguments:
| ethtool_sprintf(&data, buffer[i].name);
or when it's used with format string: "%s"
| ethtool_sprintf(&data, "%s", buffer[i].name);
which both now become:
| ethtool_puts(&data, buffer[i].name);
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a list of valid protocols for which the driver will provide
it's deferred xmit handler.
When using DSA_TAG_PROTO_KSZ8795 protocol, it does not provide a
"connect" method, therefor ksz_connect() is not allocating ksz_tagger_data.
This avoids the following null pointer dereference:
ksz_connect_tag_protocol from dsa_register_switch+0x9ac/0xee0
dsa_register_switch from ksz_switch_register+0x65c/0x828
ksz_switch_register from ksz_spi_probe+0x11c/0x168
ksz_spi_probe from spi_probe+0x84/0xa8
spi_probe from really_probe+0xc8/0x2d8
Fixes: ab32f56a4100 ("net: dsa: microchip: ptp: add packet transmission timestamping")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20231206071655.1626479-1-sean@geanix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With the ksz_chip_id enums moved to the platform include file for ksz
switches, platform code that instantiates a device can now use these to
set ksz_platform_data::chip_id.
Signed-off-by: Daniel Danzberger <dd@embedd.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ksz driver has bits and pieces of platform_data probing support, but
it doesn't work.
The conventional thing to do is to have an encapsulating structure for
struct dsa_chip_data that gets put into dev->platform_data. This driver
expects a struct ksz_platform_data, but that doesn't contain a struct
dsa_chip_data as first element, which will obviously not work with
dsa_switch_probe() -> dsa_switch_parse().
Pointing dev->platform_data to a struct dsa_chip_data directly is in
principle possible, but that doesn't work either. The driver has
ksz_switch_detect() to read the device ID from hardware, followed by
ksz_check_device_id() to compare it against a predetermined expected
value. This protects against early errors in the SPI/I2C communication.
With platform_data, the mechanism in ksz_check_device_id() doesn't work
and even leads to NULL pointer dereferences, since of_device_get_match_data()
doesn't work in that probe path.
So obviously, the platform_data support is actually missing, and the
existing handling of struct ksz_platform_data is bogus. Complete the
support by adding a struct dsa_chip_data as first element, and fixing up
ksz_check_device_id() to pick up the platform_data instead of the
unavailable of_device_get_match_data().
The early dev->chip_id assignment from ksz_switch_register() is also
bogus, because ksz_switch_detect() sets it to an initial value. So
remove it.
Also, ksz_platform_data :: enabled_ports isn't used anywhere, delete it.
Link: https://lore.kernel.org/netdev/20231204154315.3906267-1-dd@embedd.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Daniel Danzberger <dd@embedd.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Microchip KSZ8863/KSZ8873 have the ability to select between internal
and external RMII reference clock. By default, reference clock
needs to be provided via REFCLKI_3 pin. If required, device can be
setup to provide RMII clock internally so that REFCLKI_3 pin can be
left unconnected.
Add a new "microchip,rmii-clk-internal" property which will set
RMII clock reference to internal. If property is not set, reference
clock needs to be provided externally.
While at it, move the ksz8795_cpu_interface_select() to
ksz8_config_cpu_port() to get a cleaner call path for cpu port.
Signed-off-by: Ante Knezic <ante.knezic@helmholz.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 4a56212774ac, USXGMII support was added for 6393X, but this was
lost in the PCS conversion (the blamed commit), most likely because
these efforts where more or less done in parallel.
Restore this feature by porting Michal's patch to fit the new
implementation.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Michal Smulski <michal.smulski@ooma.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Fixes: e5b732a275f5 ("net: dsa: mv88e6xxx: convert 88e639x to phylink_pcs")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Link: https://lore.kernel.org/r/20231205221359.3926018-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Last part of the driver do now support phylink_mac_link_up(). So, make it
not optional.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20231127145101.3039399-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch introduces the function 'ksz8_phy_port_link_up' to the
Microchip KSZ8xxx driver. This function is responsible for setting up
flow control and duplex settings for the ports that are integrated with
PHYs.
The KSZ8795 switch supports asymmetric pause control, which can't be
fully utilized since a single bit controls both RX and TX pause. Despite
this, the flow control can be adjusted based on the auto-negotiation
process, taking into account the capabilities of both link partners.
On the other hand, the KSZ8873's PORT_FORCE_FLOW_CTRL bit can be set by
the hardware bootstrap, which ignores the auto-negotiation result.
Therefore, even in auto-negotiation mode, we need to ensure that this
bit is correctly set.
When auto-negotiation isn't in use, we enforce symmetric pause control
for the KSZ8795 switch.
Please note, forcing flow control disable on a port while still
advertising pause support isn't possible. While this scenario
might not be practical or desired, it's important to be aware of this
limitation when working with the KSZ8873 and similar devices.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20231127145101.3039399-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow flow control, speed, and duplex settings on the CPU port to be
configurable. Previously, the speed and duplex relied on default switch
values, which limited flexibility. Additionally, flow control was
hardcoded and only functional in duplex mode. This update enhances the
configurability of these parameters.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20231127145101.3039399-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As of commit b92143d4420f ("net: dsa: mv88e6xxx: add infrastructure for
phylink_pcs") probing of a Marvell 88e6350 switch causes a NULL pointer
de-reference like this example:
...
mv88e6085 d0072004.mdio-mii:11: switch 0x3710 detected: Marvell 88E6350, revision 2
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000000 when read
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] ARM
Modules linked in:
CPU: 0 PID: 8 Comm: kworker/u2:0 Not tainted 6.7.0-rc2-dirty #26
Hardware name: Marvell Armada 370/XP (Device Tree)
Workqueue: events_unbound deferred_probe_work_func
PC is at mv88e6xxx_port_setup+0x1c/0x44
LR is at dsa_port_devlink_setup+0x74/0x154
pc : [<c057ea24>] lr : [<c0819598>] psr: a0000013
sp : c184fce0 ip : c542b8f4 fp : 00000000
r10: 00000001 r9 : c542a540 r8 : c542bc00
r7 : c542b838 r6 : c5244580 r5 : 00000005 r4 : c5244580
r3 : 00000000 r2 : c542b840 r1 : 00000005 r0 : c1a02040
...
The Marvell 6350 switch has no SERDES interface and so has no
corresponding pcs_ops defined for it. But during probing a call is made
to mv88e6xxx_port_setup() which unconditionally expects pcs_ops to exist -
though the presence of the pcs_ops->pcs_init function is optional.
Modify code to check for pcs_ops first, before checking for and calling
pcs_ops->pcs_init. Modify checking and use of pcs_ops->pcs_teardown
which may potentially suffer the same problem.
Fixes: b92143d4420f ("net: dsa: mv88e6xxx: add infrastructure for phylink_pcs")
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of commit de5c9bf40c45 ("net: phylink: require supported_interfaces to
be filled") Marvell 88e6350 switches fail to be probed:
...
mv88e6085 d0072004.mdio-mii:11: switch 0x3710 detected: Marvell 88E6350, revision 2
mv88e6085 d0072004.mdio-mii:11: phylink: error: empty supported_interfaces
error creating PHYLINK: -22
mv88e6085: probe of d0072004.mdio-mii:11 failed with error -22
...
The problem stems from the use of mv88e6185_phylink_get_caps() to get
the device capabilities. Create a new dedicated phylink_get_caps for the
6351 family (which the 6350 is one of) to properly support their set of
capabilities.
According to chip.h the 6351 switch family includes the 6171, 6175, 6350
and 6351 switches, so update each of these to use the correct
phylink_get_caps.
Fixes: de5c9bf40c45 ("net: phylink: require supported_interfaces to be filled")
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a dev_dbg message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/all/20231026065408.1087824-1-colin.i.king@gmail.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
